In bfq_update_peak_rate, to check whether an I/O request rq is
sequential, only the seek distance of rq w.r.t. the last request
dispatched is controlled. This is not sufficient for non-rotational
storage, where the size of rq is at least as relevant. This commit adds
the missing control.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfq detects the creation of multiple bfq_queues shortly after each
other, namely a burst of queue creations in the terminology used in the
code. If the burst is large, then no queue in the burst is granted
- either I/O-dispatch plugging when the queue remains temporarily idle
while in service;
- or weight raising, because it causes even longer plugging.
In fact, such a plugging tends to lower throughput, while these bursts
are typically due to applications or services that spawn multiple
processes, to reach a common goal as soon as possible. Examples are a
"git grep" or the booting of a system.
Unfortunately, disabling plugging may cause a loss of service guarantees
in asymmetric scenarios, i.e., if queue weights are differentiated or if
more than one group is active.
This commit addresses this issue by no longer disabling I/O-dispatch
plugging for queues in large bursts.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the in-service bfq_queue is sync and remains temporarily idle, then
I/O dispatching (from other queues) may be plugged. It may be dome for
two reasons: either to boost throughput, or to preserve the bandwidth
share of the in-service queue. In the first case, if the I/O of the
in-service queue, when it finally arrives, consists only of one small
I/O request, then it makes sense to plug even the I/O of the in-service
queue. In fact, serving such a small request immediately is likely to
lower throughput instead of boosting it, whereas waiting a little bit is
likely to let that request grow, thanks to request merging, and become
more profitable in terms of throughput (this is likely to happen exactly
because the I/O of the queue has been detected to boost throughput).
On the opposite end, if I/O dispatching is being plugged only to
preserve the bandwidth of the in-service queue, then it would be better
not to plug also the I/O of the in-service queue, because such a
plugging is likely to cause only loss of bandwidth for the queue.
Unfortunately, no distinction is made between the two cases, and the I/O
of the in-service queue is always plugged in case just a small I/O
request arrives. This commit draws this missing distinction and does not
perform harmful plugging.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a preparatory commit for commits that need to check only one of
the two main reasons for idling. This change should also improve the
quality of the code a little bit, by splitting a function that contains
very long, non-trivial and little related comments.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In asymmetric scenarios, i.e., when some bfq_queue or bfq_group needs to
be guaranteed a different bandwidth than other bfq_queues or bfq_groups,
these service guaranteed can be provided only by plugging I/O dispatch,
completely or partially, when the queue in service remains temporarily
empty. A case where asymmetry is particularly strong is when some active
bfq_queues belong to a higher-priority class than some other active
bfq_queues. Unfortunately, this important case is not considered at all
in the code for detecting asymmetric scenarios. This commit adds the
missing logic.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before commit 18e5a57d79 ("block, bfq: postpone rq preparation to
insert or merge"), the destination queue for a request was chosen by a
different hook than the one that then inserted the request. So, between
the execution of the two hooks, the bic of the process generating the
request could happen to be redirected to a different bfq_queue. As a
consequence, the destination bfq_queue stored in the request could be
wrong. Such an event does not need to ba handled any longer.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With some unlucky sequences of events, the function bfq_updated_next_req
updates the current budget of a bfq_queue to a lower value than the
service received by the queue using such a budget. Unfortunately, if
this happens, then the return value of the function bfq_bfqq_budget_left
becomes inconsistent. This commit solves this problem by lower-bounding
the budget computed in bfq_updated_next_req to the service currently
charged to the queue.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To boost throughput on devices with internal queueing and in scenarios
where device idling is not strictly needed, bfq immediately starts
serving a new bfq_queue if the in-service bfq_queue remains without
pending I/O, even if new I/O may arrive soon for the latter queue. Then,
if such I/O actually arrives soon, bfq preempts the new in-service
bfq_queue so as to give the previous queue a chance to go on being
served (in case the previous queue should actually be the one to be
served, according to its timestamps).
However, the in-service bfq_queue, say Q, may also be without further
budget when it remains also pending I/O. Since bfq changes budgets
dynamically to fit the needs of bfq_queues, this happens more often than
one may expect. If this happens, then there is no point in trying to go
on serving Q when new I/O arrives for it soon: Q would be expired
immediately after being selected for service. This would only cause
useless overhead. This commit avoids such a useless selection.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The speed at which a bfq_queue receives I/O is one of the parameters by
which bfq decides whether the queue is soft real-time (i.e., whether the
queue contains the I/O of a soft real-time application). In particular,
when a bfq_queue remains without outstanding I/O requests, bfq computes
the minimum time instant, named soft_rt_next_start, at which the next
request of the queue may arrive for the queue to be deemed as soft real
time.
Unfortunately this filtering may cause problems with a queue in
interactive weight raising. In fact, such a queue may be conveying the
I/O needed to load a soft real-time application. The latter will
actually exhibit a soft real-time I/O pattern after it finally starts
doing its job. But, if soft_rt_next_start is updated for an interactive
bfq_queue, and the queue has received a lot of service before remaining
with no outstanding request (likely to happen on a fast device), then
soft_rt_next_start is assigned such a high value that, for a very long
time, the queue is prevented from being possibly considered as soft real
time.
This commit removes the updating of soft_rt_next_start for bfq_queues in
interactive weight raising.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The mtip32xx driver uses managed resources for DMA coherent memory
and irqs, but then always pairs them with free calls anyway, making
the resource tracking rather pointless. Given some DMA allocations
are transient anyway, the irq freeing seems to require ordering vs
other hardware access the best solution seems to be to stop using
the managed resource API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 2d29f6b96d.
It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone. Let's revert this
for now to have more time for a proper fix.
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While there's a control to allow setting it at runtime, as the
control handler is per file handler, only the application setting
the m2m device can change it. As this is a custom control, it is
unlikely that existing apps would be able to set it.
Due to that, and due to the fact that v4l2-mem2mem serializes all
accesses to a m2m device, trying to setup two GStreamer
v4l2videoconvert instance at the same time will cause frame drops.
So, add an alternate way of setting its default via a modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It doesn't make sense to have a per-device work queue, as the
scheduler should be called per file handler. Having a single
one causes failures if multiple streams are filtered by vim2m.
So, move it to be inside the context structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Despite vim2m is reporting that it supports RGB565BE and YUYV,
that's not true.
Right now, it just says that it supports both format, but it
doesn't actually support them.
Also, horizontal flip is not properly implemented. It sounds
that it was designed to do a pseudo-horizontal flip using 8
tiles. Yet, as it doesn't do format conversion, the result
is a mess.
I suspect that it was done this way in order to save CPU time,
at the time of OMAP2 days.
That's messy and doesn't really help if someone wants to
use vim2m to test a pipeline.
Worse than that, the unique RGB format it says it supports is
RGB565BE, with is not supported by Gstreamer. That prevents
practical usage of it, even for tests.
So, instead, properly implement fourcc format conversions,
adding a few more RGB formats:
- RGB and BGR with 24 bits
- RGB565LE (known as RGB16 at gstreamer)
Also allows using any of the 5 supported formats as either
capture or output.
Note: The YUYV conversion routines are based on the conversion code
written by Hans de Goede inside libv4lconvert (part of v4l-utils),
released under LGPGL 2.1 (GPL 2.0 compatible).
Tested all possible format combinations except for RGB565BE,
as Gstreamer currently doesn't support it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This Kselftest update for Linux 5.0-rc5 consists of run-time fixes to
cpu-hotplug, and seccomp tests, compile fixes to ir, net, and timers
Makefiles.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAlxTPLEACgkQCwJExA0N
Qxw7bBAApuoZgq9tdot9yE6BWZ6TFXtaZxRt/Y3ZFSMPqyF2pgizSHI4XIXGaPqe
22EUrCPnSVUwa/2FZRdhMj0gZKAUdHFIZ5/CvuxwrCDOcT0iwsju9u4a23Ms0wKb
/Rgijyshv/25Rc26wUYSHPw1U9cU+THneOb+DsMABRoHP2kbwAFiXUWDkPLCrunL
x85F9NKqlIAE4yv8GcyXMrU6ZMd6ute8UZa5nkBY5HZOX0dqLNgjDflzqUUAwJyE
d0JdOfE6vdyD+bENGzRf6+7C0XCf2ykzPyzWkcqfoQ/1k0fuLlLyySkKlXLx9uF3
5b7cdxKapmWSP+/kVXb/G7JyEgUSw94wX9+JWT39SBio0kbkifQIt5B4rGUglHnh
Zq9ePRXxwE+7KRI1SPnHTrFlx/fbi9WtREj8vMeKtZxwLn/gaLD8dbt8T6c2909i
oOOQH3zdt7w88pD64KantSJ88yNRAtKfgYMkjPosMo7hR7yA29MHtsuwSeydcLs6
XBx04RJceWUnbhPoMIsi03VFJQ1GOBXjyjBgfpKp25BVaAfC4f7XRPqpib/a/iDr
kp32Dz/9PedqkyG8hO6H9VDxC9YBQBDKIJ0me/lKe9R8lqp4a086qOjR+DGE8qye
U9o2tVCkQjY6A0mTiT/HDDtlah30q1sZ7E0GZowKVJOSLfK1U8Q=
=PV+K
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This consists of run-time fixes to cpu-hotplug, and seccomp tests,
compile fixes to ir, net, and timers Makefiles"
* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: timers: use LDLIBS instead of LDFLAGS
selftests: net: use LDLIBS instead of LDFLAGS
selftests/seccomp: Enhance per-arch ptrace syscall skip tests
selftests: Use lirc.h from kernel tree, not from system
selftests: cpu-hotplug: fix case where CPUs offline > CPUs present
These options have just moved around, let's update with make
savedefconfig to make patching the file easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
PROVE_LOCKING enables LOCKDEP, which causes big overhead on cache and
bus transactions.
On some ARM big.LITTLE architecutres (Exynos 5433) the overhead is really big.
The overhead can be measures using hackbench which will speed up
by x3 times (11sec -> 3.4sec).
When you check transaction on cache or buses, the results are way higher
than normal for the same hackbench test:
L1d cache invalidations: 26mln vs 4mln
L2u cache invalidations: 42mln vs 12mln
bus cyc/access: 30cyc/access vs. 20cyc/access
context switch is x3 times cheaper
Enable this option only when you have some locking issue to investigate.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There still is a race window after the commit b027e2298b
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
CPU0 CPU1
---- ----
tty_open
tty_init_dev
tty_ldisc_unlock
schedule
flush_to_ldisc
receive_buf
tty_port_default_receive_buf
tty_ldisc_receive_buf
n_tty_receive_buf_common
__receive_buf
uart_flush_chars
uart_start
/*tty->driver_data is NULL*/
tty->ops->open
/*init tty->driver_data*/
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com>
Tested-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/tty/serial/mps2-uart.c:351:6: warning: logical not is only
applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^ ~
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses after the
'!' to evaluate the bitwise operator first
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses around left
hand side expression to silence this warning
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
1 warning generated.
As it was intended for this check to be the inverse of the one at the
bottom of mps2_init_port, add parentheses around the whole conditional.
Fixes: 775ea4ea2f ("serial: mps2-uart: support combined irq")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/344
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() prefers calling devm_request_mem_region() with a
resource name instead of a device name -- this looks pretty iff a resource
name isn't specified via a device tree with a "reg-names" property (in this
case, a resource name is set to a device node's full name), but if it is,
it doesn't really scale since these names are only unique to a given device
node, not globally; so, looking at the output of 'cat /proc/iomem', you do
not have an idea which memory region belongs to which device (see "dirmap",
"regs", and "wbuf" lines below):
08000000-0bffffff : dirmap
48000000-bfffffff : System RAM
48000000-48007fff : reserved
48080000-48b0ffff : Kernel code
48b10000-48b8ffff : reserved
48b90000-48c7afff : Kernel data
bc6a4000-bcbfffff : reserved
bcc0f000-bebfffff : reserved
bec0e000-bec0efff : reserved
bec11000-bec11fff : reserved
bec12000-bec14fff : reserved
bec15000-bfffffff : reserved
e6050000-e605004f : gpio@e6050000
e6051000-e605104f : gpio@e6051000
e6052000-e605204f : gpio@e6052000
e6053000-e605304f : gpio@e6053000
e6054000-e605404f : gpio@e6054000
e6055000-e605504f : gpio@e6055000
e6060000-e606050b : pin-controller@e6060000
e6e60000-e6e6003f : e6e60000.serial
e7400000-e7400fff : ethernet@e7400000
ee200000-ee2001ff : regs
ee208000-ee2080ff : wbuf
I think that devm_request_mem_region() should be called with dev_name()
despite the region names won't look as pretty as before (however, we gain
more consistency with e.g. the serial driver:
08000000-0bffffff : ee200000.rpc
48000000-bfffffff : System RAM
48000000-48007fff : reserved
48080000-48b0ffff : Kernel code
48b10000-48b8ffff : reserved
48b90000-48c7afff : Kernel data
bc6a4000-bcbfffff : reserved
bcc0f000-bebfffff : reserved
bec0e000-bec0efff : reserved
bec11000-bec11fff : reserved
bec12000-bec14fff : reserved
bec15000-bfffffff : reserved
e6050000-e605004f : e6050000.gpio
e6051000-e605104f : e6051000.gpio
e6052000-e605204f : e6052000.gpio
e6053000-e605304f : e6053000.gpio
e6054000-e605404f : e6054000.gpio
e6055000-e605504f : e6055000.gpio
e6060000-e606050b : e6060000.pin-controller
e6e60000-e6e6003f : e6e60000.serial
e7400000-e7400fff : e7400000.ethernet
ee200000-ee2001ff : ee200000.rpc
ee208000-ee2080ff : ee200000.rpc
Fixes: 72f8c0bfa0 ("lib: devres: add convenience function to remap a resource")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silence warnings (triggered at W=1) by adding relevant __printf
attributes.
drivers/base/cpu.c:432:2: warning: function '__cpu_device_create' might be a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a Kconfig dependency to ensure Intel Stratix10 service layer driver
can be built only on the platform that supports it.
Signed-off-by: Richard Gong <richard.gong@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable bugfix:
- Fix up return value on fatal errors in nfs_page_async_flush()
Other bugfix:
- Fix NULL pointer dereference of dev_name
-----BEGIN PGP SIGNATURE-----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=ZOXa
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"This addresses two bugs, one in the error code handling of
nfs_page_async_flush() and one to fix a potential NULL pointer
dereference in nfs_parse_devname().
Stable bugfix:
- Fix up return value on fatal errors in nfs_page_async_flush()
Other bugfix:
- Fix NULL pointer dereference of dev_name"
* tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix up return value on fatal errors in nfs_page_async_flush()
nfs: Fix NULL pointer dereference of dev_name
Drivers shouldn't be using these values, add a TODO so someone removes
them.
Changes in v2:
- Add drm_display_mode.vrefresh removal (Ville)
- Add Sam's R-b and bonus points
Changes in v3:
- Add hsync removal todo item (Daniel)
- Change vrefresh wording to make removal less optional
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Bonus-points-awarded-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129192637.73296-1-sean@poorly.run
Only three fixes: a fix for Realtek HD-audio looks lengthy, but it's
just a code shuffling, and the actual changes are fairly small. The
rest are a PCM core fix for a long-standing bug that was recently
scratched by syzkaller, and a trivial USB-audio quirk for DSD
support.
-----BEGIN PGP SIGNATURE-----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=KZ/d
-----END PGP SIGNATURE-----
Merge tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only three fixes.
The fix for Realtek HD-audio looks lengthy, but it's just a code
shuffling, and the actual changes are fairly small.
The rest are a PCM core fix for a long-standing bug that was recently
scratched by syzkaller, and a trivial USB-audio quirk for DSD support"
* tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fixed hp_pin no value
ALSA: pcm: Fix tight loop of OSS capture stream
ALSA: usb-audio: Add Opus #3 to quirks for native DSD support
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2019-01-31
An update from ieee802154 for your *net* tree.
I waited a while to see if anything else comes up, but it seems this time
we only have one fixup patch for the -rc rounds.
Colin fixed some indentation in the mcr20a drivers. That's about it.
If there are any problems with taking these two before the final 5.0 let
me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peng Donglin <dolinux.peng@gmail.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The test_insert_dup() function from lib/test_rhashtable.c passes a
pointer to a stack object to rhltable_init(). Allocate the hash table
dynamically to avoid that the following is reported with object
debugging enabled:
ODEBUG: object (ptrval) is on stack (ptrval), but NOT annotated.
WARNING: CPU: 0 PID: 1 at lib/debugobjects.c:368 __debug_object_init+0x312/0x480
Modules linked in:
EIP: __debug_object_init+0x312/0x480
Call Trace:
? debug_object_init+0x1a/0x20
? __init_work+0x16/0x30
? rhashtable_init+0x1e1/0x460
? sched_clock_cpu+0x57/0xe0
? rhltable_init+0xb/0x20
? test_insert_dup+0x32/0x20f
? trace_hardirqs_on+0x38/0xf0
? ida_dump+0x10/0x10
? jhash+0x130/0x130
? my_hashfn+0x30/0x30
? test_rht_init+0x6aa/0xab4
? ida_dump+0x10/0x10
? test_rhltable+0xc5c/0xc5c
? do_one_initcall+0x67/0x28e
? trace_hardirqs_off+0x22/0xe0
? restore_all_kernel+0xf/0x70
? trace_hardirqs_on_thunk+0xc/0x10
? restore_all_kernel+0xf/0x70
? kernel_init_freeable+0x142/0x213
? rest_init+0x230/0x230
? kernel_init+0x10/0x110
? schedule_tail_wrapper+0x9/0xc
? ret_from_fork+0x19/0x24
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the macvlan_port_exists() macro with its twin from netdevice.h
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHYs used with PCIe controller can also be used with other
controllers such as USB or SATA. In order to configure the PHY
to work with PCIe controller, invoke phy_set_mode() API with mode
set to PHY_MODE_PCIE.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
dra74x/dra76x and dra72x have separate compatible strings. Add support
for these compatible strings in pci-dra7xx driver to perform syscon
configurations required to get x2 mode working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add syscon properties required for configuring PCIe in x2 lane mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add new compatible strings for dra74x SoC (also used by dra76x) and
dra72x. This can be used to perform SoC specific configuration
(like configuring PCIe in x2 lane mode).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
The size of L2TPv2 header with all optional fields is 14 bytes.
l2tp_udp_recv_core only moves 10 bytes to the linear part of a
skb. This may lead to l2tp_recv_common read data outside of a skb.
This patch make sure that there is at least 14 bytes in the linear
part of a skb to meet the maximum need of l2tp_udp_recv_core and
l2tp_recv_common. The minimum size of both PPP HDLC-like frame and
Ethernet frame is larger than 14 bytes, so we are safe to do so.
Also remove L2TP_HDR_SIZE_NOSEQ, it is unused now.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This series adds the OPFN feature, which is used as the negotiation
protocol by TID RDMA. This adds a totally hidden, in-band negotiation
transfer that happens on the consumer's queue pair but without the
consumer's knowledge. For that reason, things like completions for OPFN
transfers must be filtered out of the completion queue and not sent to
the consumer. This feature does not impact any consumer APIs, but does
impact the driver/driver wire API.
At a high level OPFN enables exchanging parameters between two hosts
using IB compare and swap requests to a special virtual address. The
request uses a reserved IB work request opcode (see patch 3).
* opfn:
IB/hfi1: Add static trace for OPFN
IB/hfi1: Integrate OPFN into RC transactions
IB/hfi1, IB/rdmavt: Allow for extending of QP's s_ack_queue
IB/hfi1: OPFN interface
IB/hfi1: Add OPFN helper functions for TID RDMA feature
IB/hfi1: OPFN support discovery
Signed-off-by: Doug Ledford <dledford@redhat.com>
Report correct eeprom per channel power value.
Fix chan_vs_power map in mt76x0_get_power_info routine
Fixes: f2a2e819d6 ("mt76x0: remove eeprom dependency from mt76x0_get_power_info")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While cross checking PCI IDs from Intel Media SDK
and kernel Dmitry noticed this gap. So we checked the
spec and this new ID had been recently added.
v2: Adding new H_GT1 entry to i915_pci.c (Jose)
Reported-by: Dmitry Rogozhkin<dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Rogozhkin<dmitry.v.rogozhkin@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190201235049.27206-1-rodrigo.vivi@intel.com
We really want to have fastboot enabled by default to avoid an ugly
modeset during boot.
Currently we are enabling fastboot by default on gen9+ (Skylake and newer).
The intention is to enable it on older generations after it has seen more
testing on gen9+.
VLV and CHV devices are still being sold in stores today, as such it is
desirable to also enable fastboot by default on these now.
I've extensively tested fastboot=1 support on over 50 different
Bay- and Cherry-Trail devices. Testing DSI and eDP panels as well as
HDMI output (and even DP over Type-C on one device).
All 50 devices work fine with fastboot=1. On 2 devices their DSI panel
turns black as soon as the i915 driver loads when fastboot=0, so having
fastboot enabled is required for these 2 to work properly (for lack of
a better fix).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129142237.8684-1-hdegoede@redhat.com
Enables blend optimization for floating point RTs
This restores the workaround that was reverted in c358514ba8
("Revert "drm/i915/icl: WaEnableFloatBlendOptimization"").
The revert was due to the register write seemingly not sticking,
but the HW team has confirmed that this is because the
register is WO and that the workaround is indeed required.
Here the wa is added with a mask of 0 since the register is WO.
References: https://hsdes.intel.com/resource/1408134172
References: https://bugs.freedesktop.org/show_bug.cgi?id=107338
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Talha Nassar <talha.nassar@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1548983324-15344-4-git-send-email-talha.nassar@intel.com
Top comment in intel_workarounds.c says common code should come first so
lets respect that. Also, by moving the common code together opportunities
to reduce duplication will become more obvious.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1548983324-15344-2-git-send-email-talha.nassar@intel.com
The are a couple of statments that are one level too deep, fix this by
removing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch adds the static trace to the OPFN code and moves tid related
static trace code into a new header file.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
OPFN parameter negotiation allows a pair of connected RC QPs to exchange
a set of parameters in succession. This negotiation does not commence
till the first ULP request. Because OPFN operations are operations
private to the driver, they do not generate user completions or put the
QP into error when they run out of retries. This patch integrates the
OPFN protocol into the transactions of an RC QP.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The OPFN protocol uses the COMPARE_SWAP request to exchange data
between the requester and the responder and therefore needs to
be stored in the QP's s_ack_queue when the request is received
on the responder side. However, because the user does not know
anything about the OPFN protocol, this extra entry in the
queue cannot be advertised to the user. This patch adds an extra
entry in a QP's s_ack_queue.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
OPFN allows a pair of connected RC QPs to exchange a set of parameters
in succession. The parameter exchange itself is done using the IB compare
and swap request with a special virtual address. The request is triggered
using a reserved IB work request opcode. This patch implements the OPFN
interface to initialize, start, process, and reset the OPFN request.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
