RISC-V does, in-general, not have "efficient unaligned access". When
testing the RISC-V BPF JIT, some selftests failed in the verification
due to misaligned access. Annotate these tests with the
F_NEEDS_EFFICIENT_UNALIGNED_ACCESS flag.
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit f9ebd1bb41 ("mtd: rawnand: Deprecate ->erase()") discouraged
the use of this hook, so I am happy to follow the suggestion.
Although the Denali IP provides a special MAP10 command for erasing,
using it would not buy us much. The Denali IP actually works with the
generic erasing by single_erase() + ->cmdfunc hook (nand_command_lp)
+ ->cmd_ctrl hook (denali_cmd_ctrl).
This method is also deprecated, but denali_erase() can go away
irrespective of ->exec_op conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Update Documentation/networking/filter.txt and
Documentation/sysctl/net.txt to mention RISC-V.
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_base.c:5556:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5575:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5613:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_legacy.c:332:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_legacy.c:483:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This commit adds a BPF JIT for RV64G.
The JIT is a two-pass JIT, and has a dynamic prolog/epilogue (similar
to the MIPS64 BPF JIT) instead of static ones (e.g. x86_64).
At the moment the RISC-V Linux port does not support
CONFIG_HAVE_KPROBES, which means that CONFIG_BPF_EVENTS is not
supported. Thus, no tests involving BPF_PROG_TYPE_TRACEPOINT,
BPF_PROG_TYPE_PERF_EVENT, BPF_PROG_TYPE_KPROBE and
BPF_PROG_TYPE_RAW_TRACEPOINT passes.
The implementation does not support "far branching" (>4KiB).
Test results:
# modprobe test_bpf
test_bpf: Summary: 378 PASSED, 0 FAILED, [366/366 JIT'ed]
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier
...
Summary: 761 PASSED, 507 SKIPPED, 2 FAILED
Note that "test_verifier" was run with one build with
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y and one without, otherwise
many of the the tests that require unaligned access were skipped.
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y:
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier | grep -c 'NOTE.*unknown align'
0
No CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS:
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier | grep -c 'NOTE.*unknown align'
59
The two failing test_verifier tests are:
"ld_abs: vlan + abs, test 1"
"ld_abs: jump around ld_abs"
This is due to that "far branching" involved in those tests.
All tests where done on QEMU (QEMU emulator version 3.1.50
(v3.1.0-688-g8ae951fbc106)).
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add initial support for the Amlogic NAND flash controller which is
available on Meson SoCs.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Andrii Nakryiko says:
====================
This patch series adds BTF deduplication algorithm to libbpf. This algorithm
allows to take BTF type information containing duplicate per-compilation unit
information and reduce it to equivalent set of BTF types with no duplication without
loss of information. It also deduplicates strings and removes those strings that
are not referenced from any BTF type (and line information in .BTF.ext section,
if any).
Algorithm also resolves struct/union forward declarations into concrete BTF types
across multiple compilation units to facilitate better deduplication ratio. If
undesired, this resolution can be disabled through specifying corresponding options.
When applied to BTF data emitted by pahole's DWARF->BTF converter, it reduces
the overall size of .BTF section by about 65x, from about 112MB to 1.75MB, leaving
only 29247 out of initial 3073497 BTF type descriptors.
Algorithm with minor differences and preliminary results before FUNC/FUNC_PROTO
support is also described more verbosely at:
https://facebookmicrosites.github.io/bpf/blog/2018/11/14/btf-enhancement.html
v1->v2:
- rebase on latest bpf-next
- err_log/elog -> pr_debug
- btf__dedup, btf__get_strings, btf__get_nr_types listed under 0.0.2 version
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch sets up a new kind of tests (BTF dedup tests) and tests few aspects of
BTF dedup algorithm. More complete set of tests will come in follow up patches.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch implements BTF types deduplication algorithm. It allows to
greatly compress typical output of pahole's DWARF-to-BTF conversion or
LLVM's compilation output by detecting and collapsing identical types emitted in
isolation per compilation unit. Algorithm also resolves struct/union forward
declarations into concrete BTF types representing referenced struct/union. If
undesired, this resolution can be disabled through specifying corresponding options.
Algorithm itself and its application to Linux kernel's BTF types is
described in details at:
https://facebookmicrosites.github.io/bpf/blog/2018/11/14/btf-enhancement.html
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This pre-patch extracts calculation of amount of space taken by BTF type descriptor
for later reuse by btf_dedup functionality.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are about to simplify the locking in the rawnand framework, and part
of this simplication is about getting rid of chip->state, so let's
first patch drivers that check the state.
All of them do that to get a timeout value based on the operation that
is being executed. Since a timeout is, by definition, something that
is here to prevent hanging on an event that might never happen,
picking the maximum timeout value no matter the operation should be
harmless.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stop initializing omap_gpmc_controller fields are declaration time and
replace that by a call to nand_controller_init(). Since the same object
might be shared by several NAND chips and the NAND controller driver
expects a ->probe() per-chip, we need to keep track of the
omap_gpmc_controller state (whether it's already been initialized or
not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller->wq has never been meant to be used by NAND controller
drivers. This waitqueue is used by the framework to serialize accesses
to a NAND controller, and messing up with its state is a really bad
idea.
Declare a completion object in tmio_nand and use it to wait for RB
transitions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller_init() has been added to simplify nand_controller
struct initialization. Use this function instead of duplicating the
logic.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In non-EDO, tREA should be less than tRP to guarantee that the
controller does not sample the IO lines too early. Unfortunately, the
sunxi NAND controller does not allow us to have different values for
tRP and tREH (tRP = tREH = tRW / 2).
We have 2 options to overcome this limitation:
1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint
2/ Use EDO mode (only works if timings->tRLOH > 0)
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The datasheet specifies the upper four bits are reserved.
Testing on real hardware shows that these bits can indeed be nonzero.
Signed-off-by: Emil Lenngren <emil.lenngren@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix the struct description and use standard kernel-doc header format
(even if the file is not parsed by the doc generator).
We also replace tabs by a single space.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
And get rif of all legacy hooks and unused fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag and fix MODULE_LICENSE() to
match GPL-2.0+.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace them by nand_chip pointers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_chip objects are sometimes called chip and sometimes nand. Rename
all of them into nand to make things consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use struct_size() to calculate sunxi_nand object size.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
sunxi_nand_chip objects are sometimes called chip and other times
called sunxi_nand. Make that consistent and name all occurrences
sunxi_nand.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch adds the polling mode, a basic mode that do not need
any DMA channels. This mode is also useful for debug purpose.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch is based on FMC2 command sequencer.
The purpose of the command sequencer is to facilitate the programming
and the reading of NAND flash pages with the ECC and to free the CPU
of sequencing tasks.
It requires one DMA channel for write and two DMA channels for read
operations.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4 and
MT29F8G16ABACAH4
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NMI handling code should be executed between calls to nmi_enter and
nmi_exit.
Add a separate domain handler to properly setup NMI context when handling
an interrupt requested as NMI.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide flow handlers that are NMI safe for interrupts and percpu_devid
interrupts.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for percpu_devid interrupts treated as NMIs.
Percpu_devid NMIs need to be setup/torn down on each CPU they target.
The same restrictions as for global NMIs still apply for percpu_devid NMIs.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add functionality to allocate interrupt lines that will deliver IRQs
as Non-Maskable Interrupts. These allocations are only successful if
the irqchip provides the necessary support and allows NMI delivery for the
interrupt line.
Interrupt lines allocated for NMI delivery must be enabled/disabled through
enable_nmi/disable_nmi_nosync to keep their state consistent.
To treat a PERCPU IRQ as NMI, the interrupt must not be shared nor threaded,
the irqchip directly managing the IRQ must be the root irqchip and the
irqchip cannot be behind a slow bus.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since 2.5.34 the code has had the potential to not allocate siginfo
for SIGSTOP signals. Except for ptrace this is perfectly fine as only
ptrace can use PTRACE_PEEK_SIGINFO and see what the contents of
the delivered siginfo are.
Users of PTRACE_PEEK_SIGINFO that care about the contents siginfo
for SIGSTOP are rare, but they do exist. A seccomp self test
has cared and lldb cares.
Jack Andersen <jackoalan@gmail.com> writes:
> The patch titled
> `signal: Never allocate siginfo for SIGKILL or SIGSTOP`
> created a regression for users of PTRACE_GETSIGINFO needing to
> discern signals that were raised via the tgkill syscall.
>
> A notable user of this tgkill+ptrace combination is lldb while
> debugging a multithreaded program. Without the ability to detect a
> SIGSTOP originating from tgkill, lldb does not have a way to
> synchronize on a per-thread basis and falls back to SIGSTOP-ing the
> entire process.
Everyone affected by this please note. The kernel can still fail to
allocate a siginfo structure. The allocation is with GFP_KERNEL and
is best effort only. If memory is tight when the signal allocation
comes in this will fail to allocate a siginfo.
So I strongly recommend looking at more robust solutions for
synchronizing with a single thread such as PTRACE_INTERRUPT. Or if
that does not work persuading your friendly local kernel developer to
build the interface you need.
Reported-by: Tycho Andersen <tycho@tycho.ws>
Reported-by: Kees Cook <keescook@chromium.org>
Reported-by: Jack Andersen <jackoalan@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Christian Brauner <christian@brauner.io>
Cc: stable@vger.kernel.org
Fixes: f149b31557 ("signal: Never allocate siginfo for SIGKILL or SIGSTOP")
Fixes: 6dfc88977e42 ("[PATCH] shared thread signals")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Update copyright years and remove a comment which grew incorrect and
useless over time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support both Python 2 and Python 3 in tests/attr.py
The use of "except as" syntax implies the minimum supported Python2 version is
now v2.6
Committer testing:
$ make -C tools/perf PYTHON3=python install-bin
Before:
# perf test attr
16: Setup struct perf_event_attr : FAILED!
48: Synthesize attr update : Ok
[root@quaco ~]# perf test -v attr
16: Setup struct perf_event_attr :
--- start ---
test child forked, pid 3121
File "/home/acme/libexec/perf-core/tests/attr.py", line 324
except Unsup, obj:
^
SyntaxError: invalid syntax
test child finished with -1
---- end ----
Setup struct perf_event_attr: FAILED!
48: Synthesize attr update :
--- start ---
test child forked, pid 3124
test child finished with 0
---- end ----
Synthesize attr update: Ok
#
After:
# perf test attr
16: Setup struct perf_event_attr : Ok
48: Synthesize attr update : Ok
#
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20190124005229.16146-7-tonyj@suse.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Assure a GISA is in use before accessing the IPM to avoid a
null pointer dereference issue.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-16-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
By initializing the GIB, it will be used by the kvm host.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-15-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The patch implements a handler for GIB alert interruptions
on the host. Its task is to alert guests that interrupts are
pending for them.
A GIB alert interrupt statistic counter is added as well:
$ cat /proc/interrupts
CPU0 CPU1
...
GAL: 23 37 [I/O] GIB Alert
...
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-14-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Function kvm_s390_gisa_clear() now clears the Interruption
Pending Mask of the GISA asap. If the GISA is in the alert
list at this time it stays in the list but is removed by
process_gib_alert_list().
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-13-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add the Interruption Alert Mask (IAM) to the architecture specific
kvm struct. This mask in the GISA is used to define for which ISC
a GIB alert will be issued.
The functions kvm_s390_gisc_register() and kvm_s390_gisc_unregister()
are used to (un)register a GISC (guest ISC) with a virtual machine and
its GISA.
Upon successful completion, kvm_s390_gisc_register() returns the
ISC to be used for GIB alert interruptions. A negative return code
indicates an error during registration.
Theses functions will be used by other adapter types like AP and PCI to
request pass-through interruption support.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-12-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Adding the kvm reference to struct sie_page2 will allow to
determine the kvm a given gisa belongs to:
container_of(gisa, struct sie_page2, gisa)->kvm
This functionality will be required to process a gisa in
gib alert interruption context.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-11-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The Guest Information Block (GIB) links the GISA of all guests
that have adapter interrupts pending. These interrupts cannot be
delivered because all vcpus of these guests are currently in WAIT
state or have masked the respective Interruption Sub Class (ISC).
If enabled, a GIB alert is issued on the host to schedule these
guests to run suitable vcpus to consume the pending interruptions.
This mechanism allows to process adapter interrupts for currently
not running guests.
The GIB is created during host initialization and associated with
the Adapter Interruption Facility in case an Adapter Interruption
Virtualization Facility is available.
The GIB initialization and thus the activation of the related code
will be done in an upcoming patch of this series.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-10-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch implements the Set Guest Information Block operation
to request association or disassociation of a Guest Information
Block (GIB) with the Adapter Interruption Facility. The operation
is required to receive GIB alert interrupts for guest adapters
in conjunction with AIV and GISA.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-9-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Use this struct analog to the kvm interruption structs
for kvm emulated floating and local interruptions.
GIB handling will add further fields to this structure as
required.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-8-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This will shorten the length of code lines. All GISA related
static inline functions are local to interrupt.c.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-7-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Interruption types that are not represented in GISA shall
use pending_irqs_no_gisa() to test pending interruptions.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-6-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
