The HOST1X_CHANNEL_DMAEND is an offset relative to the value written to
the HOST1X_CHANNEL_DMASTART register, but it is currently treated as an
absolute address. This can cause SMMU faults if the CDMA fetches past a
pushbuffer's IOMMU mapping.
Properly setting the DMAEND prevents the CDMA from fetching beyond that
address and avoid such issues. This is currently not observed because a
whole (almost) page of essentially scratch space absorbs any excessive
prefetching by CDMA. However, changing the number of slots in the push
buffer can trigger these SMMU faults.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the ARM SMMU provides an input address space that
is 48 bits wide. However, memory clients can only address up to 40 bits.
If the geometry is used as-is, allocations of IOVA space can end up in a
region that is not addressable by the memory clients.
To fix this, restrict the IOVA space to the DMA mask of the host1x
device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 and later support 40 bits of address space. Additional
registers need to be programmed to store the full 40 bits of push
buffer addresses.
Since command stream gathers can also reside in buffers in a 40-bit
address space, a new variant of the GATHER opcode is also introduced.
It takes two parameters: the first parameter contains the lower 32
bits of the address and the second parameter contains bits 32 to 39.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CDMA push buffer can currently only handle opcodes that take a
single word parameter. However, the host1x implementation on Tegra186
and later supports opcodes that require multiple words as parameters.
Unfortunately the way the push buffer is structured, these wide opcodes
cannot simply be composed of two regular opcodes because that could
result in the wide opcode being split across the end of the push buffer
and the final RESTART opcode required to wrap the push buffer around
would break the wide opcode.
One way to fix this would be to remove the concept of slots to simplify
push buffer operations. However, that's not entirely trivial and should
be done in a separate patch. For now, simply use a different function
to push four-word opcodes into the push buffer. Technically only three
words are pushed, with the fourth word used as padding to preserve the
2-word alignment required by the slots abstraction. The fourth word is
always a NOP opcode.
Additional care must be taken when the end of the push buffer is
reached. If a four-word opcode doesn't fit into the push buffer without
being split by the boundary, NOP opcodes will be introduced and the new
wide opcode placed at the beginning of the push buffer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When processing command streams, make sure the host1x's stream ID is
programmed for the channel so that addresses are properly translated
through the SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is one button and a notifier for incoming phone
calls/text messages for which we should wakeup from
suspend.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to use an external link when the file is already here.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To correctly set the size of the image in a plane, it's needed
to divide the height of image by the vertical down sampling factor.
This was only happening in vivid_try_fmt_vid_cap(), but now it
applied in others sizeimage calculations as well.
Signed-off-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a linear pipeline logic for the stream control. It's created by
walking backwards on the entity graph. When the stream starts it will
simply loop through the pipeline calling the respective process_frame
function of each entity.
Fixes: f2fe89061d ("vimc: Virtual Media Controller core, capture
and sensor")
Cc: stable@vger.kernel.org # for v4.20
Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fixed small space-after-tab issue in the patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function is no longer used, so drop it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Internally use ktime_get_ns() to get the timestamp of the event.
Only convert to timespec when interfacing with userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This enables mute LED support and fixes switching jacks when the laptop
is docked.
Signed-off-by: Jurica Vukadin <jurica.vukadin@rt-rk.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
update_wm_post is meant for pre-g4x only. Don't ever set
it on g4x+.
The only effect of a bogus update_wm_post on g4x+ could
be that we clear the legacy_cursor_update flag in
intel_atomic_commit(). Since legacy_cursor_update is
only set for legacy cursor updates (as the name suggests)
and we only set update_wm_post for a modeset the two
cases should never occur at the same time. But let's
be consistent in setting update_wm_post so we don't
end up confusing so many people.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206185433.8116-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add support for booting secondary CPUs on MT7629.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The comparison css->pipes[pipe].bindex < 0 is always false because
bindex is an unsigned int. Fix this by using a signed integer for
the comparison.
Detected by CoverityScan, CID#1476023 ("Unsigned compared against 0")
Fixes: f5f2e42735 ("media: staging/intel-ipu3: Add css pipeline programming")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since ipu3_css_buf_dequeue() never returns NULL, remove the
dead code to fix static checker warning:
drivers/staging/media/ipu3/ipu3.c:493 imgu_isr_threaded()
warn: 'b' is an error pointer or valid
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
[Bug report: https://lore.kernel.org/linux-media/20190104122856.GA1169@kadam/]
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This addresses the below TODO item.
- Use V4L2_CTRL_TYPE_MENU for dual-pipe mode control. (Sakari)
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The UVC video driver converts the timestamp from hardware specific unit
to one known by the kernel at the time when the buffer is dequeued. This
is fine in general, but the streamoff operation consists of the
following steps (among other things):
1. uvc_video_clock_cleanup --- the hardware clock sample array is
released and the pointer to the array is set to NULL,
2. buffers in active state are returned to the user and
3. buf_finish callback is called on buffers that are prepared.
buf_finish includes calling uvc_video_clock_update that accesses the
hardware clock sample array.
The above is serialised by a queue specific mutex. Address the problem
by skipping the clock conversion if the hardware clock sample array is
already released.
Fixes: 9c0863b1cc ("[media] vb2: call buf_finish from __queue_cancel")
Reported-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When initially testing the Camera Terminal Descriptor wTerminalType
field (buffer[4]), no mask is used. Later in the function, the MSB is
overloaded to store the descriptor subtype, and so a mask of 0x7fff
is used to check the type.
If a descriptor is specially crafted to set this overloaded bit in the
original wTerminalType field, the initial type check will fail (falling
through, without adjusting the buffer size), but the later type checks
will pass, assuming the buffer has been made suitably large, causing an
overflow.
Avoid this problem by checking for the MSB in the wTerminalType field.
If the bit is set, assume the descriptor is bad, and abort parsing it.
Originally reported here:
https://groups.google.com/forum/#!topic/syzkaller/Ot1fOE6v1d8
A similar (non-compiling) patch was provided at that time.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Alistair Strachan <astrachan@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we fallback to use "mediatek,mt7623" for MT7623a, remove unused
root node property "mediatek,mt7623a" in the document.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The SOURCE_CHANGE event is decoder specific, so don't allow it for
encoders.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in the bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check that the selection buf_type is valid before calling get_q_data() to
avoid hitting the WARN(1) in that function if the buffer type is not valid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+44b24cff6bf96006ecfa@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 2cc1802f62 ("media: vb2: Keep dma-buf buffers mapped until
they are freed") removed code leaving a local variable unused.
Remove it to avoid a compiler warning.
Fixes: 2cc1802f62 ("media: vb2: Keep dma-buf buffers mapped until they are freed")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3b99ab7dec.
The compatible "mediatek,mt7623a" is useless, so remove it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Apply backpressure to hogs that emit requests faster than the GPU can
process them by waiting for their ring to be less than half-full before
proceeding with taking the struct_mutex.
This is a gross hack to apply throttling backpressure, the long term
goal is to remove the struct_mutex contention so that each client
naturally waits, preferably in an asynchronous, nonblocking fashion
(pipelined operations for the win), for their own resources and never
blocks another client within the driver at least. (Realtime priority
goals would extend to ensuring that resource contention favours high
priority clients as well.)
This patch only limits excessive request production and does not attempt
to throttle clients that block waiting for eviction (either global GTT or
system memory) or any other global resources, see above for the long term
goal.
No microbenchmarks are harmed (to the best of my knowledge).
Testcase: igt/gem_exec_schedule/pi-ringfull-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207071829.5574-1-chris@chris-wilson.co.uk
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc81 ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
If we have a kernel configured for periodic timer interrupts, and we
have cpuidle enabled, then we end up with CPU1 losing timer interupts
after a hotplug.
This can manifest itself in RCU stall warnings, or userspace becoming
unresponsive.
The problem is that the kernel initially wants to use the TWD timer
for interrupts, but the TWD loses context when we enter the C3 cpuidle
state. Nothing reprograms the TWD after idle.
We have solved this in the past by switching to broadcast timer ticks,
and cpuidle44xx switches to that mode at boot time. However, there is
nothing to switch from periodic mode local timers after a hotplug
operation.
We call tick_broadcast_enter() in omap_enter_idle_coupled(), which one
would expect would take care of the issue, but internally this only
deals with one-shot local timers - tick_broadcast_enable() on the other
hand only deals with periodic local timers. So, we need to call both.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: just standardized the subject line]
Signed-off-by: Tony Lindgren <tony@atomide.com>
dirent modification events (create/delete/move) do not carry the
child entry name/inode information. Instead, we report FAN_ONDIR
for mkdir/rmdir so user can differentiate them from creat/unlink.
This is consistent with inotify reporting IN_ISDIR with dirent events
and is useful for implementing recursive directory tree watcher.
We avoid merging dirent events referring to subdirs with dirent events
referring to non subdirs, otherwise, user won't be able to tell from a
mask FAN_CREATE|FAN_DELETE|FAN_ONDIR if it describes mkdir+unlink pair
or rmdir+create pair of events.
For backward compatibility and consistency, do not report FAN_ONDIR
to user in legacy fanotify mode (reporting fd) and report FAN_ONDIR
to user in FAN_REPORT_FID mode for all event types.
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The bluetooth-keyboard which comes with the Toshiba WT10A tablet uses
a couple of usage codes in the vendor specific ffbc page.
The keyboard has a vendor-id of 04f2 which maps to Chicony.
Other then adding a few keymappings for the ffbc usages, no special
handling is necessary. So rather then adding a new hid-toshiba driver,
this commit adds the ID and 2 extra key-mappings to the hid-topseed
driver. The hid-topseed driver already contains mapping for some
ffbc usages (and does nothing else) and it already binds to another
Chicony manufactured keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxXYaEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGkSQH/2yrfnviNPFYpZOR
QQdc71Bfhkd8m85SmWIsSebkxmi3hKFVj15sGbWXd6+0/VxjEEGvQCZpvVwJceke
LwDxtkKGg/74wAqJvlSAWxFNZ+Had4jDeoSoeQChddsBVXBBCxQx2v6ECg3o2x7W
k8Z8t4+3RijDf8fYXY9ETyO2zW8R/wgT+dnl+DPgUH7u4dxh7FzAUfc4bgZIDg+i
FzBQfbTJuz4BU7uRZ9IJiwhWKv0Iyi2DR3BY8Z1pqEpRaUMJMrCs2WGytHbTgt9e
0EtO1airbVneU4eumU/ZaF9cyEbah9HousEPnP7J09WG4s/Odxc4zE+uK1QqS2im
5Xv88is=
=dVd1
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into fbdev-for-next
Linux 5.0-rc5
Sync with upstream (which now contains fbdev-v5.0-rc3 changes) to
prepare a base for fbdev-v5.1 changes.
