Replace the license boiler plate with a SPDX license identifier.
While in the area, update an email address.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Replace the license boiler plate with a SPDX license identifier.
While in the area, update an email address.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Replace the license boiler plate with a SPDX license identifier.
While in the area, update an email address.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Replace the license boiler plate with a SPDX license identifier.
While in the area, update an email address.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Replace the license boiler plate with a SPDX license identifier.
While in the area, update an email address.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Add device tree bindings for the ADC controller on JZ47xx SoCs,
used by the ingenic-adc driver.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add documentation for the ADC controller on JZ47xx SoCs,
used by the ingenic-adc driver.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We are using "if (ret < 0)" in many places in which the function returns 0
on success. Use "if (ret)" instead for better clarity and correctness.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we snap the timestamp after reading from the buffer and
processing the event. When the IIO poll function is triggered by an
interrupt, we can get a slightly more accurate timestamp by snapping it
prior to reading the data, since the data was already generated prior to
entering the trigger handler. This is not going to make a huge difference,
but we might as well improve slightly.
Do this by using iio_pollfunc_store_time as other drivers do.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
RussianNeuroMancer reported that the Intel 7265 wifi on a Dell Venue 11 Pro
7140 table stopped working after wakeup from suspend and bisected the
problem to 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't
have LTR"). David Ward reported the same problem on a Dell Latitude 7350.
After af8bb9f898 ("PCI/ACPI: Request LTR control from platform before
using it"), we don't enable LTR unless the platform has granted LTR control
to us. In addition, we don't notice if the platform had already enabled
LTR itself.
After 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have
LTR"), we avoid using LTR if we don't think the path to the device has LTR
enabled.
The combination means that if the platform itself enables LTR but declines
to give the OS control over LTR, we unnecessarily avoided using ASPM L1.2.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201469
Fixes: 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR")
Fixes: af8bb9f898 ("PCI/ACPI: Request LTR control from platform before using it")
Reported-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Reported-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.18+
We have added an optional boolean property for configuring a BMI160
interrupt pin as open-drain, as opposed to the default push-pull, so
document this.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bmi160 bindings say that the BMI160 requires level-triggered,
active-low interrupts, but it actually supports all interrupt types, so fix
the note to reflect that.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add interrupt support for the data ready signal on the BMI160, which fires
an interrupt whenever new accelerometer/gyroscope data is ready to read.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX identifiers (GPL 2) for the BMI160 driver. bmi160.h had an
identifier, but the other files did not.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In 'commit 752f66a75a ("bcache: use REQ_PRIO to indicate bio for
metadata")' REQ_META is replaced by REQ_PRIO to indicate metadata bio.
This assumption is not always correct, e.g. XFS uses REQ_META to mark
metadata bio other than REQ_PRIO. This is why Nix noticed that bcache
does not cache metadata for XFS after the above commit.
Thanks to Dave Chinner, he explains the difference between REQ_META and
REQ_PRIO from view of file system developer. Here I quote part of his
explanation from mailing list,
REQ_META is used for metadata. REQ_PRIO is used to communicate to
the lower layers that the submitter considers this IO to be more
important that non REQ_PRIO IO and so dispatch should be expedited.
IOWs, if the filesystem considers metadata IO to be more important
that user data IO, then it will use REQ_PRIO | REQ_META rather than
just REQ_META.
Then it seems bios with REQ_META or REQ_PRIO should both be cached for
performance optimation, because they are all probably low I/O latency
demand by upper layer (e.g. file system).
So in this patch, when we want to decide whether to bypass the cache,
REQ_META and REQ_PRIO are both checked. Then both metadata and
high priority I/O requests will be handled properly.
Reported-by: Nix <nix@esperi.org.uk>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Andre Noll <maan@tuebingen.mpg.de>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable@vger.kernel.org
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.
This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
c->error_limit is in type unsigned int, it is set via cache set sysfs
file io_error_limit. Inside the bcache code, input string is converted
by strtoul_or_return() and set the converted value to c->error_limit.
Because the converted value is unsigned long, and c->error_limit is
unsigned int, if the input is large enought, overflow will happen to
c->error_limit.
This patch uses sysfs_strtoul_clamp() to convert input string, and set
the range in [0, UINT_MAX] to avoid the potential overflow.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
c->journal_delay_ms is in type unsigned short, it is set via sysfs
interface and converted by sysfs_strtoul() from input string to
unsigned short value. Therefore overflow to unsigned short might be
happen when the converted value exceed USHRT_MAX. e.g. writing
65536 into sysfs file journal_delay_ms, c->journal_delay_ms is set to
0.
This patch uses sysfs_strtoul_clamp() to convert the input string and
limit value range in [0, USHRT_MAX], to avoid the input overflow.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dc->writeback_rate_minimum is type unsigned integer variable, it is set
via sysfs interface, and converte from input string to unsigned integer
by d_strtoul_nonzero(). When the converted input value is larger than
UINT_MAX, overflow to unsigned integer happens.
This patch fixes the overflow by using sysfs_strotoul_clamp() to
convert input string and limit the value in range [1, UINT_MAX], then
the overflow can be avoided.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current code already uses d_strtoul_nonzero() to convert input string
to an unsigned integer, to make sure writeback_rate_p_term_inverse
won't be zero value. But overflow may happen when converting input
string to an unsigned integer value by d_strtoul_nonzero(), then
dc->writeback_rate_p_term_inverse can still be set to 0 even if the
sysfs file input value is not zero, e.g. 4294967296 (a.k.a UINT_MAX+1).
If dc->writeback_rate_p_term_inverse is set to 0, it might cause a
dev-zero error in following code from __update_writeback_rate(),
int64_t proportional_scaled =
div_s64(error, dc->writeback_rate_p_term_inverse);
This patch replaces d_strtoul_nonzero() by sysfs_strtoul_clamp() and
limit the value range in [1, UINT_MAX]. Then the unsigned integer
overflow and dev-zero error can be avoided.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dc->writeback_rate_i_term_inverse can be set via sysfs interface. It is
in type unsigned int, and convert from input string by d_strtoul(). The
problem is d_strtoul() does not check valid range of the input, if
4294967296 is written into sysfs file writeback_rate_i_term_inverse,
an overflow of unsigned integer will happen and value 0 is set to
dc->writeback_rate_i_term_inverse.
In writeback.c:__update_writeback_rate(), there are following lines of
code,
integral_scaled = div_s64(dc->writeback_rate_integral,
dc->writeback_rate_i_term_inverse);
If dc->writeback_rate_i_term_inverse is set to 0 via sysfs interface,
a div-zero error might be triggered in the above code.
Therefore we need to add a range limitation in the sysfs interface,
this is what this patch does, use sysfs_stroul_clamp() to replace
d_strtoul() and restrict the input range in [1, UINT_MAX].
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sysfs file writeback_delay is used to configure dc->writeback_delay
which is type unsigned int. But bcache code uses sysfs_strtoul() to
convert the input string, therefore it might be overflowed if the input
value is too large. E.g. input value is 4294967296 but indeed 0 is
set to dc->writeback_delay.
This patch uses sysfs_strtoul_clamp() to convert the input string and
set the result value range in [0, UINT_MAX] to avoid such unsigned
integer overflow.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When setting bcache parameters via sysfs, there are some variables are
defined as bit-field value. Current bcache code in sysfs.c uses either
d_strtoul() or sysfs_strtoul() to convert the input string to unsigned
integer value and set it to the corresponded bit-field value.
The problem is, the bit-field value only takes the lowest bit of the
converted value. If input is 2, the expected value (like bool value)
of the bit-field value should be 1, but indeed it is 0.
The following sysfs files for bit-field variables have such problem,
bypass_torture_test, for dc->bypass_torture_test
writeback_metadata, for dc->writeback_metadata
writeback_running, for dc->writeback_running
verify, for c->verify
key_merging_disabled, for c->key_merging_disabled
gc_always_rewrite, for c->gc_always_rewrite
btree_shrinker_disabled,for c->shrinker_disabled
copy_gc_enabled, for c->copy_gc_enabled
This patch uses sysfs_strtoul_bool() to set such bit-field variables,
then if the converted value is non-zero, the bit-field variables will
be set to 1, like setting a bool value like expensive_debug_checks.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When setting bool values via sysfs interface, e.g. writeback_metadata,
if writing 1 into writeback_metadata file, dc->writeback_metadata is
set to 1, but if writing 2 into the file, dc->writeback_metadata is
0. This is misleading, a better result should be 1 for all non-zero
input value.
It is because dc->writeback_metadata is a bit-field variable, and
current code simply use d_strtoul() to convert a string into integer
and takes the lowest bit value. To fix such error, we need a routine
to convert the input string into unsigned integer, and set target
variable to 1 if the converted integer is non-zero.
This patch introduces a new macro called sysfs_strtoul_bool(), it can
be used to convert input string into bool value, we can use it to set
bool value for bit-field vairables.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value
4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.
This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cache set congested threshold values congested_read_threshold_us and
congested_write_threshold_us can be set via sysfs interface. These
two values are 'unsigned int' type, but sysfs interface uses strtoul
to convert input string. So if people input a large number like
9999999999, the value indeed set is 1410065407, which is not expected
behavior.
This patch replaces sysfs_strtoul() by sysfs_strtoul_clamp() when
convert input string to unsigned int value, and set value range in
[0, UINT_MAX], to avoid the above integer overflow errors.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently sysfs_strtoul_clamp() is defined as,
82 #define sysfs_strtoul_clamp(file, var, min, max) \
83 do { \
84 if (attr == &sysfs_ ## file) \
85 return strtoul_safe_clamp(buf, var, min, max) \
86 ?: (ssize_t) size; \
87 } while (0)
The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.
To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.
Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stale && dirty keys can be produced in the follow way:
After writeback in write_dirty_finish(), dirty keys k1 will
replace by clean keys k2
==>ret = bch_btree_insert(dc->disk.c, &keys, NULL, &w->key);
==>btree_insert_fn(struct btree_op *b_op, struct btree *b)
==>static int bch_btree_insert_node(struct btree *b,
struct btree_op *op,
struct keylist *insert_keys,
atomic_t *journal_ref,
Then two steps:
A) update k1 to k2 in btree node memory;
bch_btree_insert_keys(b, op, insert_keys, replace_key)
B) Write the bset(contains k2) to cache disk by a 30s delay work
bch_btree_leaf_dirty(b, journal_ref).
But before the 30s delay work write the bset to cache device,
these things happened:
A) GC works, and reclaim the bucket k2 point to;
B) Allocator works, and invalidate the bucket k2 point to,
and increase the gen of the bucket, and place it into free_inc
fifo;
C) Until now, the 30s delay work still does not finish work,
so in the disk, the key still is k1, it is dirty and stale
(its gen is smaller than the gen of the bucket). and then the
machine power off suddenly happens;
D) When the machine power on again, after the btree reconstruction,
the stale dirty key appear.
In bch_extent_bad(), when expensive_debug_checks is off, it would
treat the dirty key as good even it is stale keys, and it would
cause bellow probelms:
A) In read_dirty() it would cause machine crash:
BUG_ON(ptr_stale(dc->disk.c, &w->key, 0));
B) It could be worse when reads hits stale dirty keys, it would
read old incorrect data.
This patch tolerate the existence of these stale && dirty keys,
and treat them as bad key in bch_extent_bad().
(Coly Li: fix indent which was modified by sender's email client)
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a hunk of code that is indented one level too deep, fix this
by removing the extra tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When there are multiple bcache devices, after a reboot the name of
bcache devices may change (e.g. current /dev/bcache1 was /dev/bcache0
before reboot). Therefore we need the backing device UUID (sb.uuid) to
identify each bcache device.
Backing device uuid can be found by program bcache-super-show, but
directly exporting backing_dev_uuid by sysfs file
/sys/block/bcache<?>/bcache/backing_dev_uuid is a much simpler method.
With backing_dev_uuid, and partition uuids from /dev/disk/by-partuuid/,
now we can identify each bcache device and its partitions conveniently.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch export dc->backing_dev_name to sysfs file
/sys/block/bcache<?>/bcache/backing_dev_name, then people or user space
tools may know the backing device name of this bcache device.
Of cause it can be done by parsing sysfs links, but this method can be
much simpler to find the link between bcache device and backing device.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In stats.c:bch_cache_accounting_clear(), a hard coded number '7' is
used in memset(). It is because in struct cache_stats, there are 7
atomic_t type members. This is not good when new members added into
struct stats, the hard coded number will only clear part of memory.
This patch replaces 'sizeof(unsigned long) * 7' by more generic
'sizeof(struct cache_stats))', to avoid potential error if new
member added into struct cache_stats.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The generic netlink code is expected to trigger notification messages when
configuration might have been changed. But the configuration of batman-adv
is most of the time still done using sysfs. So the sysfs interface should
also trigger the corresponding netlink messages via the "config" multicast
group.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The B.A.T.M.A.N. V implementation tries to estimate the link throughput of
an interface to an originator using different automatic methods. It is
still possible to overwrite it the link throughput for all reachable
originators via this interface.
The BATADV_CMD_SET_HARDIF/BATADV_CMD_GET_HARDIF commands allow to set/get
the configuration of this feature using the u32
BATADV_ATTR_THROUGHPUT_OVERRIDE attribute. The used unit is in 100 Kbit/s.
If the value is set to 0 then batman-adv will try to estimate the
throughput by itself.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP packets are transmitted every elp_interval milliseconds on an
slave/hard-interface. This value can be changed using the configuration
interface.
The BATADV_CMD_SET_HARDIF/BATADV_CMD_GET_HARDIF commands allow to set/get
the configuration of this feature using the u32 BATADV_ATTR_ELP_INTERVAL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The OGM packets are transmitted every orig_interval milliseconds. This
value can be changed using the configuration interface.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u32 BATADV_ATTR_ORIG_INTERVAL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can use (in an homogeneous mesh) network coding, a
mechanism that aims to increase the overall network throughput by fusing
multiple packets in one transmission.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_NETWORK_CODING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can optimize the flooding of multicast packets based on
the content of the global translation tables. To disable this behavior and
use the broadcast-like flooding of the packets, forceflood has to be
enabled.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_MULTICAST_FORCEFLOOD_ENABLED attribute. Setting the u8 to zero
will disable this feature (allowing multicast optimizations) and setting it
to something else is enabling this feature (forcing simple flooding).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In contrast to other modules, batman-adv allows to set the debug message
verbosity per mesh/soft-interface and not per module (via modparam).
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u32 (bitmask) BATADV_ATTR_LOG_LEVEL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The TQ (B.A.T.M.A.N. IV) and throughput values (B.A.T.M.A.N. V) are reduced
when they are forwarded. One of the reductions is the penalty for
traversing an additional hop. This hop_penalty (0-255) defines the
percentage of reduction (0-100%).
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u8 BATADV_ATTR_HOP_PENALTY
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh/soft-interface can optimize the handling of DHCP packets. Instead
of flooding them through the whole mesh, it can be forwarded as unicast to
a specific gateway server. The originator which injects the packets in the
mesh has to select (based on sel_class thresholds) a responsible gateway
server. This is done by switching this originator to the gw_mode client.
The servers announce their forwarding bandwidth (download/upload) when the
gw_mode server was selected.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the attributes:
* u8 BATADV_ATTR_GW_MODE (0 == off, 1 == client, 2 == server)
* u32 BATADV_ATTR_GW_BANDWIDTH_DOWN (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_BANDWIDTH_UP (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_SEL_CLASS
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can fragment unicast packets when the packet size
exceeds the outgoing slave/hard-interface MTU.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_FRAGMENTATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can use a distributed hash table to answer ARP requests
without flooding the request through the whole mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can try to detect loops in the same mesh caused by
(indirectly) bridged mesh/soft-interfaces of different nodes. Some of the
loops can also be resolved without breaking the mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can use multiple slave/hard-interface ports at the same
time to transport the traffic to other nodes.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_BONDING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can drop messages between clients to implement a
mesh-wide AP isolation.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH and
BATADV_CMD_SET_VLAN/BATADV_CMD_GET_VLAN commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AP_ISOLATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
This feature also requires that skbuff which should be handled as isolated
are marked. The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to
set/get the mark/mask using the u32 attributes BATADV_ATTR_ISOLATION_MARK
and BATADV_ATTR_ISOLATION_MASK.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can delay OGM messages to aggregate different ogms
together in a single OGM packet.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AGGREGATED_OGMS_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the VLANs on top of
the mesh/soft-interface have configuration settings. The genl interface
reflects this by allowing to get/set it using the vlan specific commands
BATADV_CMD_GET_VLAN/BATADV_CMD_SET_VLAN.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_VLAN command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the
slave/hard-interface have B.A.T.M.A.N. V specific configuration settings.
The genl interface reflects this by allowing to get/set it using the
hard-interface specific commands.
The BATADV_CMD_GET_HARDIFS (or short version BATADV_CMD_GET_HARDIF) is
reused as get command because it already allow sto dump the content of
other information from the slave/hard-interface which are not yet
configuration specific.
The set command BATADV_CMD_SET_HARDIF will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_HARDIF
command message type that settings might have been changed and what the
current values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
