struct blk_issue_stat squashes three things into one u64:
- The time the driver started working on a request
- The original size of the request (for the io.low controller)
- Flags for writeback throttling
It turns out that on x86_64, we have a 4 byte hole in struct request
which we can fill with the non-timestamp fields from blk_issue_stat,
simplifying things quite a bit.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct blk_issue_stat is going away, and bio->bi_issue_stat doesn't even
use the blk-stats interface, so we can provide a separate implementation
specific for bios. The helpers work the same way as the blk-stats
helpers.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Gets rid of those warnings and better document the parameters.
./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip'
./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip'
./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This symbol is now always identical to CONFIG_ARCH_DMA_ADDR_T_64BIT, so
remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
This way we have one central definition of it, and user can select it as
needed. Note that we now also always select it when CONFIG_DMA_API_DEBUG
is select, which fixes some incorrect checks in a few network drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
This avoids selecting IOMMU_HELPER just for this function. And we only
use it once or twice in normal builds so this often even is a size
reduction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This code is only used by sparc, and all new iommu drivers should use the
drivers/iommu/ framework. Also remove the unused exports.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
This implements of_genpd_opp_to_performance_state() which can be used
from the device drivers or the OPP core to find the performance state
encoded in the "required-opps" property of a node. Normally this would
be called only once for each OPP of the device for which the OPP table
of the device is getting generated.
Different platforms may encode the performance state differently using
the OPP table (they may simply return value of opp-hz or opp-microvolt,
or apply some algorithm on top of those values) and so a new callback
->opp_to_performance_state() is implemented to allow platform specific
drivers to convert the power domain OPP to a performance state value.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The power-domain core would be using the OPP core going forward and the
OPP core has the basic requirement of a device structure for its working.
Add a struct device to the genpd structure. This doesn't register the
device with device core as the "dev" pointer is mostly used by the OPP
core as a cookie for now and registering the device is not mandatory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds a new helper to let the power domain drivers to access
opp->np, so that they can read platform specific properties from the
node.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
A device's DT node or its OPP nodes can contain a phandle to other
device's OPP node, in the "required-opps" property.
This patch implements a routine to find that required OPP from the node
that contains the "required-opps" property.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The "operating-points-v2" property can contain a list of phandles now,
specifically for the power domain providers that provide multiple
domains.
Add support to parse that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an empty arch_pkeys_enabled() in linux/pkeys.h for the
CONFIG_ARCH_HAS_PKEYS=n case.
Split out of a patch by Ram Pai <linuxram@us.ibm.com>.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Move the last remaining pkey helper, vma_pkey() into asm/pkeys.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Consolidate the pkey handling by providing a common empty definition
of vma_pkey() in pkeys.h when CONFIG_ARCH_HAS_PKEYS=n.
This also removes another entanglement of pkeys.h and
asm/mmu_context.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
While trying to unify the pkey handling in show_smap() between x86 and
powerpc we stumbled across various build failures due to the order of
includes between the two arches.
Part of the problem is that linux/pkeys.h includes asm/mmu_context.h,
and the relationship between asm/mmu_context.h and asm/pkeys.h is not
consistent between the two arches.
It would be cleaner if linux/pkeys.h only included asm/pkeys.h,
creating a single integration point for the arch pkey definitions.
So this patch removes the include of asm/mmu_context.h from
linux/pkeys.h.
We can't prove that this is safe in the general case, but it passes
all the build tests I've thrown at it. Also asm/mmu_context.h is
included widely while linux/pkeys.h is not, so most likely any code
that is including linux/pkeys.h is already getting asm/mmu_context.h
from elsewhere.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently only 4bits are allocated in the vma flags to hold 16
keys. This is sufficient for x86. PowerPC supports 32 keys,
which needs 5bits. This patch allocates an additional bit.
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
[mpe: Fold in #if VM_PKEY_BIT4 as noticed by Dave Hansen]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
VM_PKEY_BITx are defined only if CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
is enabled. Powerpc also needs these bits. Hence lets define the
VM_PKEY_BITx bits for any architecture that enables
CONFIG_ARCH_HAS_PKEYS.
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most mainstream architectures are using 65536 entries, so lets stick to
that. If someone is really desperate to override it that can still be
done through <asm/dma-mapping.h>, but I'd rather see a really good
rationale for that.
dma_debug_init is now called as a core_initcall, which for many
architectures means much earlier, and provides dma-debug functionality
earlier in the boot process. This should be safe as it only relies
on the memory allocator already being available.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Seccomp logging for "handled" actions such as RET_TRAP, RET_TRACE, or
RET_ERRNO can be very noisy for processes that are being audited. This
patch modifies the seccomp logging behavior to treat processes that are
being inspected via the audit subsystem the same as processes that
aren't under inspection. Handled actions will no longer be logged just
because the process is being inspected. Since v4.14, applications have
the ability to request logging of handled actions by using the
SECCOMP_FILTER_FLAG_LOG flag when loading seccomp filters.
With this patch, the logic for deciding if an action will be logged is:
if action == RET_ALLOW:
do not log
else if action not in actions_logged:
do not log
else if action == RET_KILL:
log
else if action == RET_LOG:
log
else if filter-requests-logging:
log
else:
do not log
Reported-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The decision to log a seccomp action will always be subject to the
value of the kernel.seccomp.actions_logged sysctl, even for processes
that are being inspected via the audit subsystem, in an upcoming patch.
Therefore, we need to emit an audit record on attempts at writing to the
actions_logged sysctl when auditing is enabled.
This patch updates the write handler for the actions_logged sysctl to
emit an audit record on attempts to write to the sysctl. Successful
writes to the sysctl will result in a record that includes a normalized
list of logged actions in the "actions" field and a "res" field equal to
1. Unsuccessful writes to the sysctl will result in a record that
doesn't include the "actions" field and has a "res" field equal to 0.
Not all unsuccessful writes to the sysctl are audited. For example, an
audit record will not be emitted if an unprivileged process attempts to
open the sysctl file for reading since that access control check is not
part of the sysctl's write handler.
Below are some example audit records when writing various strings to the
actions_logged sysctl.
Writing "not-a-real-action", when the kernel.seccomp.actions_logged
sysctl previously was "kill_process kill_thread trap errno trace log",
emits this audit record:
type=CONFIG_CHANGE msg=audit(1525392371.454:120): op=seccomp-logging
actions=? old-actions=kill_process,kill_thread,trap,errno,trace,log
res=0
If you then write "kill_process kill_thread errno trace log", this audit
record is emitted:
type=CONFIG_CHANGE msg=audit(1525392401.645:126): op=seccomp-logging
actions=kill_process,kill_thread,errno,trace,log
old-actions=kill_process,kill_thread,trap,errno,trace,log res=1
If you then write "log log errno trace kill_process kill_thread", which
is unordered and contains the log action twice, it results in the same
actions value as the previous record:
type=CONFIG_CHANGE msg=audit(1525392436.354:132): op=seccomp-logging
actions=kill_process,kill_thread,errno,trace,log
old-actions=kill_process,kill_thread,errno,trace,log res=1
If you then write an empty string to the sysctl, this audit record is
emitted:
type=CONFIG_CHANGE msg=audit(1525392494.413:138): op=seccomp-logging
actions=(none) old-actions=kill_process,kill_thread,errno,trace,log
res=1
No audit records are generated when reading the actions_logged sysctl.
Suggested-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
When the core networking needs to detect the transport offset in a given
packet and parse it explicitly, a full-blown flow_keys struct is used for
storage.
This patch introduces a smaller keys store, rework the basic flow dissect
helper to use it, and apply this new helper where possible - namely in
skb_probe_transport_header(). The used flow dissector data structures
are renamed to match more closely the new role.
The above gives ~50% performance improvement in micro benchmarking around
skb_probe_transport_header() and ~30% around eth_get_headlen(), mostly due
to the smaller memset. Small, but measurable improvement is measured also
in macro benchmarking.
v1 -> v2: use the new helper in eth_get_headlen() and skb_get_poff(),
as per DaveM suggestion
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 67db3e4bfb ("tcp: no longer hold ehash lock while calling
tcp_get_info()") removes the only users of u64_stats_update_end/begin_raw()
without removing the function in header file.
Remove no longer used functions.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if a device supports extended config space, i.e., it is a PCI-X Mode 2
or a PCI Express device, the extended space may not be accessible if
there's a conventional PCI bus in the path to it.
We currently figure that out in pci_cfg_space_size() by reading the first
dword of extended config space. On most platforms that returns ~0 data if
the space is inaccessible, but it may set error bits in PCI status
registers, and on some platforms it causes exceptions that we currently
don't recover from.
For example, a PCIe-to-conventional PCI bridge treats config transactions
with a non-zero Extended Register Address as an Unsupported Request on PCIe
and a received Master-Abort on the destination bus (see PCI Express to
PCI/PCI-X Bridge spec, r1.0, sec 4.1.3).
A sample case is a LS1043A CPU (NXP QorIQ Layerscape) platform with the
following bus topology:
LS1043 PCIe Root Port
-> PEX8112 PCIe-to-PCI bridge (doesn't support ext cfg on PCI side)
-> PMC slot connector (for legacy PMC modules)
With a PMC module topology as follows:
PMC connector
-> PCI-to-PCIe bridge
-> PCIe switch (4 ports)
-> 4 PCIe devices (one on each port)
The PCIe devices on the PMC module support extended config space, but we
can't reach it because the PEX8112 can't generate accesses to the extended
space on its secondary bus. Attempts to access it cause Unsupported
Request errors, which result in synchronous aborts on this platform.
To avoid these errors, check whether bridges are capable of generating
extended config space addresses on their secondary interfaces. If they
can't, we restrict devices below the bridge to only the 256-byte
PCI-compatible config space.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
[bhelgaas: changelog, rework patch so bus_flags testing is all in
pci_bridge_child_ext_cfg_accessible()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several PCIe hotplug controllers have errata that mean they do not set the
Command Completed bit unless writes to the Slot Command register change
"Control" bits. Command Completed is never set for writes that only change
software notification "Enable" bits. This results in timeouts like this:
pciehp 0000:00:1c.0:pcie004: Timeout on hotplug command 0x1038 (issued 65284 msec ago)
When this erratum is present, avoid these timeouts by marking commands
"completed" immediately unless they change the "Control" bits.
Here's the text of the Intel erratum CF118. We assume this applies to all
Intel parts:
CF118 PCIe Slot Status Register Command Completed bit not always
updated on any configuration write to the Slot Control
Register
Problem: For PCIe root ports (devices 0 - 10) supporting hot-plug,
the Slot Status Register (offset AAh) Command Completed
(bit[4]) status is updated under the following condition:
IOH will set Command Completed bit after delivering the new
commands written in the Slot Controller register (offset
A8h) to VPP. The IOH detects new commands written in Slot
Control register by checking the change of value for Power
Controller Control (bit[10]), Power Indicator Control
(bits[9:8]), Attention Indicator Control (bits[7:6]), or
Electromechanical Interlock Control (bit[11]) fields. Any
other configuration writes to the Slot Control register
without changing the values of these fields will not cause
Command Completed bit to be set.
The PCIe Base Specification Revision 2.0 or later describes
the “Slot Control Register” in section 7.8.10, as follows
(Reference section 7.8.10, Slot Control Register, Offset
18h). In hot-plug capable Downstream Ports, a write to the
Slot Control register must cause a hot-plug command to be
generated (see Section 6.7.3.2 for details on hot-plug
commands). A write to the Slot Control register in a
Downstream Port that is not hotplug capable must not cause a
hot-plug command to be executed.
The PCIe Spec intended that every write to the Slot Control
Register is a command and expected a command complete status
to abstract the VPP implementation specific nuances from the
OS software. IOH PCIe Slot Control Register implementation
is not fully conforming to the PCIe Specification in this
respect.
Implication: Software checking on the Command Completed status after
writing to the Slot Control register may time out.
Workaround: Software can read the Slot Control register and compare the
existing and new values to determine if it should check the
Command Completed status after writing to the Slot Control
register.
Per Sinan, the Qualcomm QDF2400 controller also does not set the Command
Completed bit unless writes to the Slot Command register change "Control"
bits.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Link: https://lkml.kernel.org/r/8770820b-85a0-172b-7230-3a44524e6c9f@molgen.mpg.de
Reported-by: Paul Menzel <pmenzel+linux-pci@molgen.mpg.de> # Lenovo X60
Tested-by: Paul Menzel <pmenzel+linux-pci@molgen.mpg.de> # Lenovo X60
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> # Qcom quirk
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Solve those Sphinx warnings:
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.sign' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.realbits' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.storagebits' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.shift' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.repeat' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:270: warning: Function parameter or member 'scan_type.endianness' not described in 'iio_chan_spec'
./include/linux/iio/iio.h:191: WARNING: Unexpected indentation.
./include/linux/iio/iio.h:192: WARNING: Block quote ends without a blank line; unexpected unindent.
./include/linux/iio/iio.h:198: WARNING: Definition list ends without a blank line; unexpected unindent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This simplifies allocation of the generic RPC slot and xprtrdma
specific per-RPC resources.
It also makes xprtrdma more like the socket-based transports:
->buf_alloc and ->buf_free are now responsible only for send and
receive buffers.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Refactor: xprtrdma needs to have better control over when RPCs are
awoken from the backlog queue, so replace xprt_free_slot with a
transport op callout.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
alloc_slot is a transport-specific op, but initializing an rpc_rqst
is common to all transports. In addition, the only part of initial-
izing an rpc_rqst that needs serialization is getting a fresh XID.
Move rpc_rqst initialization to common code in preparation for
adding a transport-specific alloc_slot to xprtrdma.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This was used by the ide, scsi and networking code in the past to
determine if they should bounce payloads. Now that the dma mapping
always have to support dma to all physical memory (thanks to swiotlb
for non-iommu systems) there is no need to this crude hack any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Palmer Dabbelt <palmer@sifive.com> (for riscv)
Reviewed-by: Jens Axboe <axboe@kernel.dk>
ide_toggle_bounce did select various strange block bounce limits, including
not bouncing at all as soon as an iommu is present in the system. Given
that the dma_map routines now handle any required bounce buffering except
for ISA DMA, and the ide code already must handle either ISA DMA or highmem
at least for iommu equipped systems we can get rid of the block layer
bounce limit setting entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:
1) Add Maglev support to IPVS. Moreover, store lastest server weight in
IPVS since this is needed by maglev, patches from from Inju Song.
2) Preparation works to add iptables flowtable support, patches
from Felix Fietkau.
3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
packet is seen via new teardown state, also from Felix.
4) Add support for extended netlink error reporting for nf_tables.
5) Support for larger timeouts that 23 days in nf_tables, patch from
Florian Westphal.
6) Always set an upper limit to dynamic sets, also from Florian.
7) Allow number generator to make map lookups, from Laura Garcia.
8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.
9) Extend ip6tables SRH match to support previous, next and last SID,
from Ahmed Abdelsalam.
10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.
11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.
12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
from Taehee Yoo.
13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
Make rt and exthdr built-in too, again from Florian.
14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_osf_ttl() and nf_osf_match() into nf_osf.c to prepare for
nf_tables support.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Here are some USB driver fixes for 4.17-rc4.
The majority of them are some USB gadget fixes that missed my last pull
request. The "largest" patch in here is a fix for the old visor driver
that syzbot found 6 months or so ago and I finally remembered to fix it.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWu4/Kw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykQrwCdFtLciG+1aDp5lDc8wzlOPdsUa5cAoK2f+7Je
stELc5F5nAEES/DMFG1c
=CDZC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver fixes for 4.17-rc4.
The majority of them are some USB gadget fixes that missed my last
pull request. The "largest" patch in here is a fix for the old visor
driver that syzbot found 6 months or so ago and I finally remembered
to fix it.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: host: ehci: Use dma_pool_zalloc()"
usb: typec: tps6598x: handle block reads separately with plain-I2C adapters
usb: typec: tcpm: Release the role mux when exiting
USB: Accept bulk endpoints with 1024-byte maxpacket
xhci: Fix use-after-free in xhci_free_virt_device
USB: serial: visor: handle potential invalid device configuration
USB: serial: option: adding support for ublox R410M
usb: musb: trace: fix NULL pointer dereference in musb_g_tx()
usb: musb: host: fix potential NULL pointer dereference
usb: gadget: composite Allow for larger configuration descriptors
usb: dwc3: gadget: Fix list_del corruption in dwc3_ep_dequeue
usb: dwc3: gadget: dwc3_gadget_del_and_unmap_request() can be static
usb: dwc2: pci: Fix error return code in dwc2_pci_probe()
usb: dwc2: WA for Full speed ISOC IN in DDMA mode.
usb: dwc2: dwc2_vbus_supply_init: fix error check
usb: gadget: f_phonet: fix pn_net_xmit()'s return type
This driver depends on sony-laptop driver, but this is available
only for x86. So, add a stub function, in order to allow building
it on non-x86 too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
window for the driver that got merged in the merge window. Plus a
warning fix for unused PM ops and a couple fixes for the meson clk
driver clk names that went unnoticed with the regmap rework. There's
also another fix in here for the mux rounding flag which wasn't doing
what it said it did, but now it does.
-----BEGIN PGP SIGNATURE-----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=3cjp
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes froom Stephen Boyd:
"A handful of fixes for the stm32mp1 clk driver came in during the
merge window for the driver that got merged in the merge window.
Plus a warning fix for unused PM ops and a couple fixes for the meson
clk driver clk names that went unnoticed with the regmap rework.
There's also another fix in here for the mux rounding flag which
wasn't doing what it said it did, but now it does"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: meson: meson8b: fix meson8b_cpu_clk parent clock name
clk: meson: meson8b: fix meson8b_fclk_div3_div clock name
clk: meson: drop meson_aoclk_gate_regmap_ops
clk: meson: honor CLK_MUX_ROUND_CLOSEST in clk_regmap
clk: honor CLK_MUX_ROUND_CLOSEST in generic clk mux
clk: cs2000: mark resume function as __maybe_unused
clk: stm32mp1: remove ck_apb_dbg clock
clk: stm32mp1: set stgen_k clock as critical
clk: stm32mp1: add missing tzc2 clock
clk: stm32mp1: fix SAI3 & SAI4 clocks
clk: stm32mp1: remove unused dfsdm_src[] const
clk: stm32mp1: add missing static
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=P6V8
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180504' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should to into this release. This contains:
- Set of bcache fixes from Coly, fixing regression in patches that
went into this series.
- Set of NVMe fixes by way of Keith.
- Set of bdi related fixes, one from Jan and two from Tetsuo Handa,
fixing various issues around device addition/removal.
- Two block inflight fixes from Omar, fixing issues around the
transition to using tags for blk-mq inflight accounting that we
did a few releases ago"
* tag 'for-linus-20180504' of git://git.kernel.dk/linux-block:
bdi: Fix oops in wb_workfn()
nvmet: switch loopback target state to connecting when resetting
nvme/multipath: Fix multipath disabled naming collisions
nvme/multipath: Disable runtime writable enabling parameter
nvme: Set integrity flag for user passthrough commands
nvme: fix potential memory leak in option parsing
bdi: Fix use after free bug in debugfs_remove()
bdi: wake up concurrent wb_shutdown() callers.
bcache: use pr_info() to inform duplicated CACHE_SET_IO_DISABLE set
bcache: set dc->io_disable to true in conditional_stop_bcache_device()
bcache: add wait_for_kthread_stop() in bch_allocator_thread()
bcache: count backing device I/O error for writeback I/O
bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()
bcache: store disk name in struct cache and struct cached_dev
blk-mq: fix sysfs inflight counter
blk-mq: count allocated but not started requests in iostats inflight
Switch to SPDX licensing and drop the GPL text which comes redundant.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
