The Dell Canvas 27 has a tool that can be put on the surface and acts
as a dial. The firmware processes the detection of the tool and forward
regular HID reports with X, Y, Azimuth, rotation, width/height.
The firmware also exports Contact ID, Countact Count which may hint that
several totems can be used at the same time (the FW only supports one).
We can tell that MT_TOOL_DIAL will be reported by setting the min/max
of ABS_MT_TOOL_TYPE to MT_TOOL_DIAL.
This tool is aimed at being used by the system and not the applications,
so the user space processing should not go through the regular touch
inputs.
We set INPUT_PROP_DIRECT which applies ID_INPUT_TOUCHSCREEN to this new
type of devices, but we will counter this for the time being with the
special udev hwdb entry mentioned above.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1511846
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the ULP1 mode, in order to achieve the lowest power consumption
with the system in retention mode and be able to resume on the wake
up events, all the clocks are shut off, inclusive the embedded 12MHz
RC oscillator, and the number of wake up sources is limited as well.
When the wake up event is asserted, the embedded 12MHz RC oscillator
restarts automatically.
The ULP1 (Ultra Low-power mode 1) is introduced by SAMA5D2.
The previous size of pm_suspend.o was 2148 bytes. With the addition of
ULP1 mode the new size of pm_suspend.o raised at 2456 bytes.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: aligned with 4.18-rc1]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On modern laptop, there are more and more platforms
have two GPUs, and each of them maybe have audio codec
for HDMP/DP output. For some dGPU which is no output,
audio codec usually is disabled.
In currect HDA audio driver, it will set all codec as
VGA_SWITCHEROO_DIS, the audio which is binded to UMA
will be suspended if user use debugfs to contorl power
In HDA driver side, it is difficult to know which GPU
the audio has binded to. So set the bound gpu pci dev
to vga_switcheroo.
if the audio client is not the third registration, audio
id will set in vga_switcheroo enable function. if the
audio client is the last registration when vga_switcheroo
_ready() get true, we should get audio client id from bound
GPU directly.
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some IP cores have an internal 'bus free' logic which may be more
advanced than just checking if SDA is high. Add a separate callback to
get this status. Filling it is optional.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For bus recovery, we either need to bail out early if we can read SDA or
we need to send STOP after every pulse. Otherwise recovery might be
misinterpreted as an unwanted write. So, require one of those SDA
handling functions to avoid this problem.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mm_struct always contains a cpumask bitmap, regardless of
CONFIG_CPUMASK_OFFSTACK. That means the first step can be to
simplify things, and simply have one bitmask at the end of the
mm_struct for the mm_cpumask.
This does necessitate moving everything else in mm_struct into
an anonymous sub-structure, which can be randomized when struct
randomization is enabled.
The second step is to determine the correct size for the
mm_struct slab object from the size of the mm_struct
(excluding the CPU bitmap) and the size the cpumask.
For init_mm we can simply allocate the maximum size this
kernel is compiled for, since we only have one init_mm
in the system, anyway.
Pointer magic by Mike Galbraith, to evade -Wstringop-overflow
getting confused by the dynamically sized array.
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Rik van Riel <riel@surriel.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-team@fb.com
Cc: luto@kernel.org
Link: http://lkml.kernel.org/r/20180716190337.26133-2-riel@surriel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both the implementation and the users' expectation [1] for the various
wakeup primitives have evolved over time, but the documentation has not
kept up with these changes: brings it into 2018.
[1] http://lkml.kernel.org/r/20180424091510.GB4064@hirez.programming.kicks-ass.net
Also applied feedback from Alan Stern.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Akira Yokosawa <akiyks@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Daniel Lustig <dlustig@nvidia.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jade Alglave <j.alglave@ucl.ac.uk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luc Maranget <luc.maranget@inria.fr>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arch@vger.kernel.org
Cc: parri.andrea@gmail.com
Link: http://lkml.kernel.org/r/20180716180605.16115-12-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are 11 interpretations of the requirements described in the header
comment for smp_mb__after_spinlock(): one for each LKMM maintainer, and
one currently encoded in the Cat file. Stick to the latter (until a more
satisfactory solution is available).
This also reworks some snippets related to the barrier to illustrate the
requirements and to link them to the idioms which are relied upon at its
call sites.
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: akiyks@gmail.com
Cc: dhowells@redhat.com
Cc: j.alglave@ucl.ac.uk
Cc: linux-arch@vger.kernel.org
Cc: luc.maranget@inria.fr
Cc: npiggin@gmail.com
Cc: parri.andrea@gmail.com
Cc: stern@rowland.harvard.edu
Link: http://lkml.kernel.org/r/20180716180605.16115-11-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU updates from Paul E. McKenney:
- An optimization and a fix for RCU expedited grace periods, with
the fix being from Boqun Feng.
- Miscellaneous fixes, including a lockdep-annotation fix from
Boqun Feng.
- SRCU updates.
- Updates to rcutorture and associated scripting.
- Introduce grace-period sequence numbers to the RCU-bh, RCU-preempt,
and RCU-sched flavors, replacing the old ->gpnum and ->completed
pair of fields. This change allows lockless code to obtain the
complete grace-period state with a single READ_ONCE(), which is
needed to maintain tolerable lock contention during the upcoming
consolidation of the three RCU flavors. Note that grace-period
sequence numbers are already used by rcu_barrier(), expedited
RCU grace periods, and SRCU, and are thus already heavily used
and well-tested. Joel Fernandes contributed a number of excellent
fixes and improvements.
- Clean up some grace-period-reporting loose ends, including
improving the handling of quiescent states from offline CPUs
and fixing some false-positive WARN_ON_ONCE() invocations.
(Strictly speaking, the WARN_ON_ONCE() invocations were quite
correct, but their invariants were (harmlessly) violated by the
earlier sloppy handling of quiescent states from offline CPUs.)
In addition, improve grace-period forward-progress guarantees so
as to allow removal of fail-safe checks that required otherwise
needless lock acquisitions. Finally, add more diagnostics to
help debug the upcoming consolidation of the RCU-bh, RCU-preempt,
and RCU-sched flavors.
- Additional miscellaneous fixes, including those contributed by
Byungchul Park, Mauro Carvalho Chehab, Joe Perches, Joel Fernandes,
Steven Rostedt, Andrea Parri, and Neil Brown.
- Additional torture-test changes, including several contributed by
Arnd Bergmann and Joel Fernandes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_hash size is 192 bytes, and uses 3 cache lines, if there is few
flows, gro_hash may be not fully used, so it is unnecessary to iterate
all gro_hash in napi_gro_flush(), to occupy unnecessary cacheline.
convert gro_count to a bitmask, and rename it as gro_bitmask, each bit
represents a element of gro_hash, only flush a gro_hash element if the
related bit is set, to speed up napi_gro_flush().
and update gro_bitmask only if it will be changed, to reduce cache
update
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original kexec_load syscall can not verify file signatures, nor can
the kexec image be measured. Based on policy, deny the kexec_load
syscall.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Differentiate between the kernel reading a file specified by userspace
from the kernel loading a buffer containing data provided by userspace.
This patch defines a new LSM hook named security_kernel_load_data().
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Based on RFC3376 5.1
If no interface
state existed for that multicast address before the change (i.e., the
change consisted of creating a new per-interface record), or if no
state exists after the change (i.e., the change consisted of deleting
a per-interface record), then the "non-existent" state is considered
to have a filter mode of INCLUDE and an empty source list.
Which means a new multicast group should start with state IN().
Function ip_mc_join_group() works correctly for IGMP ASM(Any-Source Multicast)
mode. It adds a group with state EX() and inits crcount to mc_qrv,
so the kernel will send a TO_EX() report message after adding group.
But for IGMPv3 SSM(Source-specific multicast) JOIN_SOURCE_GROUP mode, we
split the group joining into two steps. First we join the group like ASM,
i.e. via ip_mc_join_group(). So the state changes from IN() to EX().
Then we add the source-specific address with INCLUDE mode. So the state
changes from EX() to IN(A).
Before the first step sends a group change record, we finished the second
step. So we will only send the second change record. i.e. TO_IN(A).
Regarding the RFC stands, we should actually send an ALLOW(A) message for
SSM JOIN_SOURCE_GROUP as the state should mimic the 'IN() to IN(A)'
transition.
The issue was exposed by commit a052517a8f ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we used to send both ALLOW(A) and TO_IN(A). After this change we only send
TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add new wrapper
functions so we don't need to change too much code.
v1 -> v2:
In my first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
an filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses' sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
Fixes: a052517a8f ("net/multicast: should not send source list records when have filter mode change")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving zero_resv_unavail before memmap_init_zone(), caused a regression on
x86-32.
The cause is that we access struct pages before they are allocated when
CONFIG_FLAT_NODE_MEM_MAP is used.
free_area_init_nodes()
zero_resv_unavail()
mm_zero_struct_page(pfn_to_page(pfn)); <- struct page is not alloced
free_area_init_node()
if CONFIG_FLAT_NODE_MEM_MAP
alloc_node_mem_map()
memblock_virt_alloc_node_nopanic() <- struct page alloced here
On the other hand memblock_virt_alloc_node_nopanic() zeroes all the memory
that it returns, so we do not need to do zero_resv_unavail() here.
Fixes: e181ae0c5d ("mm: zero unavailable pages before memmap init")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Tested-by: Matt Hart <matt@mattface.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
similar to previous change, this also allows to remove it
from nf_ipv6_ops and avoid the indirection.
It also removes the bogus dependency of nf_conntrack_ipv6 on ipv6 module:
ipv6 checksum functions are built into kernel even if CONFIG_IPV6=m,
but ipv6/netfilter.o isn't.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
allows to make nf_ip_checksum_partial static, it no longer
has an external caller.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support for the Processig Units defined in
the UAC3 spec. The main difference with the previous specs
is the lack of on/off switches in the controls for these
units and the addiction of the new Multi Function Processing
Unit.
The current version of the UAC3 spec doesn't define any
useful controls for the new Multi Function Processing Unit
so no control will get created once this unit is parsed.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A recent extension to the GIC architecture allows a hypervisor to
arbitrarily reduce the number of LPIs available to a guest, no
matter what the GIC says about the valid range of IntIDs.
Let's factor in this information when computing the number of
available LPIs
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For devices with a class, we create a "glue" directory between
the parent device and the new device with the class name.
This directory is never "explicitely" removed when empty however,
this is left to the implicit sysfs removal done by kobject_release()
when the object loses its last reference via kobject_put().
This is problematic because as long as it's not been removed from
sysfs, it is still present in the class kset and in sysfs directory
structure.
The presence in the class kset exposes a use after free bug fixed
by the previous patch, but the presence in sysfs means that until
the kobject is released, which can take a while (especially with
kobject debugging), any attempt at re-creating such as binding a
new device for that class/parent pair, will result in a sysfs
duplicate file name error.
This fixes it by instead doing an explicit kobject_del() when
the glue dir is empty, by keeping track of the number of
child devices of the gluedir.
This is made easy by the fact that all glue dir operations are
done with a global mutex, and there's already a function
(cleanup_glue_dir) called in all the right places taking that
mutex that can be enhanced for this. It appears that this was
in fact the intent of the function, but the implementation was
wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use "/**" to begin this comment block since it is not a
kernel-doc comment block.
Also adjust comment line to fit in 80 characters.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for a "RZ_SCIFA" which is different than a traditional
SCIFA. It looks like a normal SCIF with FIFO data, but with a
compressed address space. Also, the break out of interrupts
are different then traditinal SCIF: ERI/BRI, RXI, TXI, TEI, DRI.
The R7S9210 (RZ/A2) contains this type of SCIF.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field support_vsel is currently only used in the device tree
case. Get rid of it. No change in behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete
These supplement the existing HS400 operation:
* prepare_hs400_tuning
This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
This can be done in an implementation of complete_hs400_tuning
If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Complete the implementation for Innova TLS (FPGA-based) hardware by
adding support for rx inline crypto offload.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new netdev tls op for resynchronizing HW tls context
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a netdev feature to configure TLS RX inline crypto offload.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decrypted bit is propogated to cloned/copied skbs.
This will be used later by the inline crypto receive side offload
of tls.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
7b0a911478 ("efi/x86: Move the EFI BGRT init code to early init code")
... removed the implementation and all the references to
efi_late_init() but the function is still declared at
include/linux/efi.h.
Hence, remove the unnecessary declaration.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180711094040.12506-6-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Presently, when a user process requests the kernel to execute any
UEFI runtime service, the kernel temporarily switches to a separate
set of page tables that describe the virtual mapping of the UEFI
runtime services regions in memory. Since UEFI runtime services are
typically invoked with interrupts enabled, any code that may be called
during this time, will have an incorrect view of the process's address
space. Although it is unusual for code running in interrupt context to
make assumptions about the process context it runs in, there are cases
(such as the perf subsystem taking samples) where this causes problems.
So let's set up a work queue for calling UEFI runtime services, so that
the actual calls are made when the work queue items are dispatched by a
work queue worker running in a separate kernel thread. Such threads are
not expected to have userland mappings in the first place, and so the
additional mappings created for the UEFI runtime services can never
clash with any.
The ResetSystem() runtime service is not covered by the work queue
handling, since it is not expected to return, and may be called at a
time when the kernel is torn down to the point where we cannot expect
work queues to still be operational.
The non-blocking variants of SetVariable() and QueryVariableInfo()
are also excluded: these are intended to be used from atomic context,
which obviously rules out waiting for a completion to be signalled by
another thread. Note that these variants are currently only used for
UEFI runtime services calls that occur very early in the boot, and
for ones that occur in critical conditions, e.g., to flush kernel logs
to UEFI variables via efi-pstore.
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
[ardb: exclude ResetSystem() from the workqueue treatment
merge from 2 separate patches and rewrite commit log]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180711094040.12506-4-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the comments in the perf events code use articles incorrectly,
using 'a' for words beginning with a vowel sound, where 'an' should be
used.
Signed-off-by: Tobias Tefke <tobias.tefke@tutanota.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: alexander.shishkin@linux.intel.com
Cc: jolsa@redhat.com
Cc: namhyung@kernel.org
Link: http://lkml.kernel.org/r/20180709105715.22938-1-tobias.tefke@tutanota.com
[ Fix a few more perf related 'a event' typo fixes from all around the kernel and tooling tree. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces a compat_id pointer member and sysfs interface
for each fpga region, similar as compat_id for fpga manager, it allows
applications to read the per region compat_id for compatibility
checking before other actions on this fpga-region (e.g. PR).
Signed-off-by: Wu Hao <hao.wu@intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces compat_id support to fpga manager, it adds
a fpga_compat_id pointer to fpga manager data structure to allow
fpga manager drivers to save the compatibility id. This compat_id
could be used for compatibility checking before doing partial
reconfiguration to associated fpga regions.
Signed-off-by: Wu Hao <hao.wu@intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds status sysfs interface for fpga manager, it's a
read only interface which allows user to get fpga manager status,
including full/partial reconfiguration error and other status
information. It adds a status callback to fpga_manager_ops too,
allows each fpga_manager driver to define its own method to
collect latest status from hardware.
The following sysfs file is created:
* /sys/class/fpga_manager/<fpga>/status
Return status of fpga manager, including reconfiguration errors.
Signed-off-by: Wu Hao <hao.wu@intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds region_id to fpga_image_info data structure, it
allows driver to pass region id information to fpga-mgr via
fpga_image_info for fpga reconfiguration function.
Signed-off-by: Wu Hao <hao.wu@intel.com>
Acked-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the initial support for Coresight Address Translation Unit, which
augments the TMC in Coresight SoC-600 by providing an improved Scatter
Gather mechanism. CATU is always connected to a single TMC-ETR and
converts the AXI address with a translated address (from a given SG
table with specific format). The CATU should be programmed in pass
through mode and enabled even if the ETR doesn't use the translation
by CATU.
This patch provides mechanism to enable/disable the CATU always in the
pass through mode.
We reuse the existing ports mechanism to link the TMC-ETR to the
connected CATU.
i.e, TMC-ETR:output_port0 -> CATU:input_port0
Reference manual for CATU component is avilable in version r2p0 of :
"Arm Coresight System-on-Chip SoC-600 Technical Reference Manual".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new coresight device type, which do not belong to any
of the existing types, i.e, source, sink, link etc. A helper
device could be connected to a coresight device, which could
augment the functionality of the coresight device.
This is intended to cover Coresight Address Translation Unit (CATU)
devices, which provide improved Scatter Gather mechanism for TMC
ETR. The idea is that the helper device could be controlled by
the driver of the device it is attached to (in this case ETR),
transparent to the generic coresight driver (and paths).
The operations include enable(), disable(), both of which could
accept a device specific "data" which the driving device and
the helper device could share. Since they don't appear in the
coresight "path" tracked by software, we have to ensure that
they are powered up/down whenever the master device is turned
on.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
