This reverts commit 55d38d060e. There were
too heavy merge conflicts and the driver code making use of this was not
ready yet anyhow. So, we wait one cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This avoid the need to always translate between the two in ata_prot_flags
and generally cleans up the taskfile protocol usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we set ATA_MAX_SECTORS_LBA48 to 65535 to avoid the corner case
in some drives that commands with "count" set to 0000h (which
reprsents 65536) does not work as expected, lba_48_ok(), which is
used for number-of-blocks checking when libata pack commands, should
use the same limit as well. In fact, there is no reason for the two
functions not to use the macros anyway.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 3647234101 (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 3647234101 ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Let's restore some of the #defines that have been savagely dropped
by the introduction of the KVM ITS code, as pointlessly break
other users (including series that are already in -next).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
arm-gic-v3.h contains bit and register definitions for the GICv3 and ITS,
at least for the bits the we currently care about.
The ITS emulation needs more definitions, so add them and refactor
the memory attribute #defines to be more universally usable.
To avoid changing all users, we still provide some of the old definitons
defined with the help of the new macros.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The kvm_io_bus framework is a nice place of holding information about
various MMIO regions for kernel emulated devices.
Add a call to retrieve the kvm_io_device structure which is associated
with a certain MMIO address. This avoids to duplicate kvm_io_bus'
knowledge of MMIO regions without having to fake MMIO calls if a user
needs the device a certain MMIO address belongs to.
This will be used by the ITS emulation to get the associated ITS device
when someone triggers an MSI via an ioctl from userspace.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The MT6323 is a regulator found on boards based on MediaTek MT7623 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes the old crypto_grab_skcipher helper and replaces
it with crypto_grab_skcipher2.
As this is the final entry point into givcipher this patch also
removes all traces of the top-level givcipher interface, including
all implicit IV generators such as chainiv.
The bottom-level givcipher interface remains until the drivers
using it are converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allows skcipher algorithms and instances to be created
and registered with the crypto API. They are accessible through
the top-level skcipher interface, along with ablkcipher/blkcipher
algorithms and instances.
This patch also introduces a new parameter called chunk size
which is meant for ciphers such as CTR and CTS which ostensibly
can handle arbitrary lengths, but still behave like block ciphers
in that you can only process a partial block at the very end.
For these ciphers the block size will continue to be set to 1
as it is now while the chunk size will be set to the underlying
block size.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The description of min_hw_heartbeat_ms is misleading and needs some
improvements.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This helps in reducing code in .remove callbacks and sometimes
dropping .remove callbacks entirely.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On mips and parisc:
drivers/bluetooth/btwilink.c: In function 'ti_st_open':
drivers/bluetooth/btwilink.c:174:21: warning: overflow in implicit constant conversion [-Woverflow]
hst->reg_status = -EINPROGRESS;
drivers/nfc/nfcwilink.c: In function 'nfcwilink_open':
drivers/nfc/nfcwilink.c:396:31: warning: overflow in implicit constant conversion [-Woverflow]
drv->st_register_cb_status = -EINPROGRESS;
There are actually two issues:
1. Whether "char" is signed or unsigned depends on the architecture.
As the completion callback data is used to pass a (negative) error
code, it should always be signed.
2. EINPROGRESS is 150 on mips, 245 on parisc.
Hence -EINPROGRESS doesn't fit in a signed 8-bit number.
Change the callback status from "char" to "int" to fix these.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a new read function to the at24 driver allowing to retrieve the
factory-programmed mac address embedded in chips from the at24mac
family.
These chips can be instantiated similarily to the at24cs family,
except that there's no way of having access to both the serial number
and the mac address at the same time - the user must instantiate
either an at24cs or at24mac device as both special memory areas are
accessible on the same slave address.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The chips from the at24cs family have two memory areas - a regular
read-write block and a read-only area containing the serial number.
The latter is visible on a different slave address (the address of the
rw memory block + 0x08). In order to access both blocks the user needs
to instantiate a regular at24c device for the rw block address and a
corresponding at24cs device on the serial number block address.
Add a function that allows to access the serial number and assign it
to at24->read_func if the chip allows serial number read operations
and the driver was passed the relevant flag for this device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use BIT() macro to replace the 0xXX constants in platform_data flags
definitions.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for hardware offloading of ipmr/ip6mr we need an
interface that allows to check (and later update) the age of entries.
Relying on stats alone can show activity but not actual age of the entry,
furthermore when there're tens of thousands of entries a lot of the
hardware implementations only support "hit" bits which are cleared on
read to denote that the entry was active and shouldn't be aged out,
these can then be naturally translated into age timestamp and will be
compatible with the software forwarding age. Using a lastuse entry doesn't
affect performance because the members in that cache line are written to
along with the age.
Since all new users are encouraged to use ipmr via netlink, this is
exported via the RTA_EXPIRES attribute.
Also do a minor local variable declaration style adjustment - arrange them
longest to shortest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Shrijeet Mukherjee <shm@cumulusnetworks.com>
CC: Satish Ashok <sashok@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec can't cope with mtu frames which need vlan tag insertion, and
vlan device set the default mtu equal to the underlying dev's one.
By default vlan over macsec devices use invalid mtu, dropping
all the large packets.
This patch adds a netif helper to check if an upper vlan device
needs mtu reduction. The helper is used during vlan devices
initialization to set a valid default and during mtu updating to
forbid invalid, too bit, mtu values.
The helper currently only check if the lower dev is a macsec device,
if we get more users, we need to update only the helper (possibly
reserving an additional IFF bit).
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7xlG
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.8-rc1
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
drm/tegra: sor: Reject HDMI 2.0 modes
drm/tegra: sor: Prepare for generic PM domain support
drm/tegra: dsi: Prepare for generic PM domain support
drm/tegra: sor: Make XBAR configurable per SoC
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
dt-bindings: display: tegra: Add source clock for SOR
drm/tegra: sor: Implement sor1_brick clock
drm/tegra: sor: Implement runtime PM
drm/tegra: hdmi: Implement runtime PM
drm/tegra: dsi: Implement runtime PM
drm/tegra: dc: Implement runtime PM
drm/tegra: hdmi: Enable audio over HDMI
drm/tegra: sor: Do not support deep color modes
drm/tegra: sor: Extract tegra_sor_mode_set()
drm/tegra: sor: Split out tegra_sor_apply_config()
drm/tegra: sor: Rename tegra_sor_calc_config()
drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
drm/tegra: dpaux: Add pinctrl support
dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
drm/tegra: Prepare DPAUX for supporting generic PM domains
...
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Aeb
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.8' of github.com:linux-nand/linux into mtd
Pull NAND changes from Boris Brezillon:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
Extend touchscreen_parse_properties() with support for the
touchscreen-inverted-x/y and touchscreen-swapped-x-y properties and
add touchscreen_set_mt_pos() and touchscreen_report_pos() helper
functions for storing coordinates into a input_mt_pos struct, or
directly reporting them, taking these properties into account.
This commit also modifies the existing callers of
touchscreen_parse_properties() to pass in NULL for the new third
argument, keeping the existing behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for non-linear data on raw records. It
extends raw records to have one or multiple fragments that will
be written linearly into the ring slot, where each fragment can
optionally have a custom callback handler to walk and extract
complex, possibly non-linear data.
If a callback handler is provided for a fragment, then the new
__output_custom() will be used instead of __output_copy() for
the perf_output_sample() part. perf_prepare_sample() does all
the size calculation only once, so perf_output_sample() doesn't
need to redo the same work anymore, meaning real_size and padding
will be cached in the raw record. The raw record becomes 32 bytes
in size without holes; to not increase it further and to avoid
doing unnecessary recalculations in fast-path, we can reuse
next pointer of the last fragment, idea here is borrowed from
ZERO_OR_NULL_PTR(), which should keep the perf_output_sample()
path for PERF_SAMPLE_RAW minimal.
This facility is needed for BPF's event output helper as a first
user that will, in a follow-up, add an additional perf_raw_frag
to its perf_raw_record in order to be able to more efficiently
dump skb context after a linear head meta data related to it.
skbs can be non-linear and thus need a custom output function to
dump buffers. Currently, the skb data needs to be copied twice;
with the help of __output_custom() this work only needs to be
done once. Future users could be things like XDP/BPF programs
that work on different context though and would thus also have
a different callback function.
The few users of raw records are adapted to initialize their frag
data from the raw record itself, no change in behavior for them.
The code is based upon a PoC diff provided by Peter Zijlstra [1].
[1] http://thread.gmane.org/gmane.linux.network/421294
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a macro regmap_read_poll_timeout that works similar
to the readx_poll_timeout defined in linux/iopoll.h, except that this
can also return the error value returned by a failed regmap_read.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Barry Song <baohua@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.310333816@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.229913786@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-samsung-soc@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.147940411@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel@stlinux.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153338.062741642@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Straight forward conversion to the state machine. Though the question arises
whether this needs really all these state transitions to work.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.982013161@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Eric Auger <eric.auger@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.900484868@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine. They are installed at runtime so
smpcfd_prepare_cpu() needs to be invoked by the boot-CPU.
Signed-off-by: Richard Weinberger <richard@nod.at>
[ Added the dropped CPU dying case back in. ]
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Davidlohr Bueso <dave@stgolabs>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.818376366@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.736898691@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs. A lot of code is removed because
the for-loop is used and create_hash_tables() is removed since its purpose
is covered by the startup / teardown hooks.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.649867675@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When tearing down, call timers_dead_cpu() before notify_dead().
There is a hidden dependency between:
- timers
- block multiqueue
- rcutree
If timers_dead_cpu() comes later than blk_mq_queue_reinit_notify()
that latter function causes a RCU stall.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.566790058@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Split out the clockevents callbacks instead of piggybacking them on
hrtimers.
This gets rid of a POST_DEAD user. See commit:
54e88fad22 ("sched: Make sure timers have migrated before killing the migration_thread")
We just move the callback state to the proper place in the state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.485419196@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Gang Wei <gang.wei@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ning Sun <ning.sun@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard L Maliszewski <richard.l.maliszewski@intel.com>
Cc: Shane Wang <shane.wang@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Cc: tboot-devel@lists.sourceforge.net
Link: http://lkml.kernel.org/r/20160713153337.400227322@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has an asymmetry of ONLINE code without any corresponding tear
down code. Otherwise, this is a straightforward conversion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.228918408@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has an asymmetry of ONLINE code without any corresponding tear
down code. Otherwise, this is a straightforward conversion.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.147128995@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: oprofile-list@lists.sf.net
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.054827168@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
The get_cpu() in xen_starting_cpu() boils down to preempt_disable() since
we already know the CPU we run on. Disabling preemption shouldn't be required
here from what I see since it we don't switch CPUs while invoking the function.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20160713153336.971559670@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
