Calling the disable_irq() from irq handler might be a bad idea as
disable_irq() should wait for handlers to run. I don't see why
this wouldn't deadlock in wait_event waiting for the threaded
handler to complete.
Use disable_irq_nosync() instead.
Fixes: 390af53e04 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/f2c4c88d90bf7473e1b84b8a99b7b33d7a081764.1612249657.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case allocation fails, we must behave correctly and exit with error.
Fixes: e6b817d4b8 ("vfio-pci/zdev: Add zPCI capabilities to VFIO_DEVICE_GET_INFO")
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
bio_init() clears bio instance, so the bvec index has to be set after
bio_init(), otherwise bio->bi_io_vec may be leaked.
Fixes: 3175199ab0 ("block: split bio_kmalloc from bio_alloc_bioset")
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We cannot modify initial_domain every time while the retry starts. That
will cause the busy waiting that unable to switch to GTT while the vram
is not enough.
Fixes: f8aab60422 ("drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs")
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
(cherry picked from commit 67fba3f1c7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm the driver will calculate a wrong MST timeslots/MTP (aka time unit)
value for MST streams if the link parameters (link rate or lane count)
are limited in a way independent of the sink capabilities (reported by
DPCD).
One example of such a limitation is when a MUX between the sink and
source connects only a limited number of lanes to the display and
connects the rest of the lanes to other peripherals (USB).
Another issue is that atm MST core calculates the divider based on the
backwards compatible DPCD (at address 0x0000) vs. the extended
capability info (at address 0x2200). This can result in leaving some
part of the MST BW unused (For instance in case of the WD19TB dock).
Fix the above two issues by calculating the PBN divider value based on
the rate and lane count link parameters that the driver uses for all
other computation.
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/2977
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-2-imre.deak@intel.com
(cherry picked from commit b59c27cab2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This function will be needed by the next patch where the driver
calculates the BW based on driver specific parameters, so export it.
At the same time sanitize the function params, passing the more natural
link rate instead of the encoding of the same rate.
v2:
- Fix function documentation. (Lyude)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-1-imre.deak@intel.com
(cherry picked from commit a321fc2b4e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Under the GHCB specification, SEV-ES guests can support string I/O.
The current #VC handler contains this support, so remove the need to
unroll kernel string I/O operations. This will reduce the number of #VC
exceptions generated as well as the number VM exits for the guest.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/3de04b5b638546ac75d42ba52307fe1a922173d3.1612203987.git.thomas.lendacky@amd.com
Receiving the first packet in an AMS sequence signals the
beginning of AMS. Set in_ams flag to true when SRC_CAPS are
received during POWER_NEGOTIATION AMS.
This fixes the failure flagged while running TD.PD.SNK.E9
compliance test.
>From Deterministic PD compliance MOI spec:
TD.PD.SNK.E9. GetSinkCap in Place of Accept
Description:
As Provider, the Tester intentionally sends a GetSinkCap message in place
of Accept message and verifies the UUT will send a SoftReset and recover
from the error.
Steps:
a) Run PROC.PD.E1 Bring-up according to the UUT role.
b) The Tester cycles VBus.
c) The Tester sends a Source Capabilities message to the UUT.
d) Upon receipt of a Request message from the UUT, the Tester replies with
a GoodCRC message.
e) The Tester sends a GetSinkCap message to the UUT.
f) If a SoftReset is not received within 15 ms after the GetSinkCap EOP was
sent, the test fails.
g) If a SoftReset is received timely, the Tester replies with an Accept
message.
h) The Tester sends Source Capabilities message to the UUT repeatedly until
nCapsCount reached or a GoodCRC is received. If nCapsCount reached, the
test fails.
i) If a Request is not received timely within 30 ms after the GoodCRC EOP
corresponding to Source Capabilities message was received, the test
fails.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202033859.258491-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in source mode, vbus could be shutoff by protections
circuits. TCPM does not move back to toggling state to
re-initiate connection. Fix this by moving to SRC_UNATTACHED
state when vbus shuts off while in source mode.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210201100212.49863-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chrome OS EC Type-C driver features implemented this round:
* Registration of cable plug information
* Support for SOP' plug registration and altmodes
* Support for reporting number of altmodes supported by partners and plugs
* Send mux configuration ack to EC via a new host command
* Reporting SOP' and Partner PD revisions
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCYBkGLgAKCRBzbaomhzOw
wjQPAQDqtiHflDd1ePu6ihRn8Zjr5xlQ+JN5zKHi7+aZsTdb7gEAtnG4KTJTq94w
RJeIrm8gIB3NNfc6cRAHZ+bTXscZ6wI=
=dfjk
-----END PGP SIGNATURE-----
Merge tag 'tag-ib-usb-typec-chrome-platform-cros-ec-typec-changes-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux into usb-next
Benson writes:
cros-ec-typec changes for usb for v5.12
Chrome OS EC Type-C driver features implemented this round:
* Registration of cable plug information
* Support for SOP' plug registration and altmodes
* Support for reporting number of altmodes supported by partners and plugs
* Send mux configuration ack to EC via a new host command
* Reporting SOP' and Partner PD revisions
* tag 'tag-ib-usb-typec-chrome-platform-cros-ec-typec-changes-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_typec: Set opmode to PD on SOP connected
platform/chrome: cros_ec_typec: Set Partner PD revision from status
platform/chrome: cros_ec_typec: Report SOP' PD revision from status
platform/chrome: cros_ec_typec: Send mux configuration acknowledgment to EC
platform/chrome: cros_ec_typec: Parameterize cros_typec_cmds_supported()
platform/chrome: cros_ec_typec: Register plug altmodes
platform/chrome: cros_ec_typec: Register SOP' cable plug
platform/chrome: cros_ec_typec: Set partner num_altmodes
platform/chrome: cros_ec_typec: Store cable plug type
platform/chrome: cros_ec_typec: Register cable
platform/chrome: cros_ec_typec: Rename discovery struct
platform/chrome: cros_ec_typec: Factor out PD identity parsing
platform/chrome: cros_ec_typec: Make disc_done flag partner-only
Add support to thinkpad_acpi for Lenovo platforms that have DYTC
version 5 support or newer to use the platform profile feature.
This will allow users to determine and control the platform modes
between low-power, balanced operation and performance modes.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210111162237.3469-1-markpearson@lenovo.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFKBAABCgA0FiEEfnIqFpAYrP8+dKQLwfwUeK3K7AkFAmAZU+IWHHV3ZUBrbGVp
bmUta29lbmlnLm9yZwAKCRDB/BR4rcrsCTuhCACc0PdS+8E3DlA0i2rtXbn0erFo
JmINp5WD9DfpVHowDP5PCQGIlUFlyO8mMAoR3VWD0LET0ZBwrDhuwUrYBkMDy6de
ce78N7owfxc7L4C6iXQmQzBEum1s9n0sjwcsHBv0LEmBCG09ikmHcFN7HP2Ek1gT
qdjWixha44A2qdptqPQChoMi/RPhaHEytMDjsxtqa6SCPBBZsUG+FyAsKipxvYj9
1E4BcQ7g7+IDhHt5D7JNIBFMNtLszEZ/Fv2YmolyGQn5i5DwNUcs4DtK0a/4R1Xa
J6rUg/KmOngx5AUOXd7ddgmvw4ebmtMZICMAAPp2ldfZhOa/4LjauAdCH8Xj
=BCZG
-----END PGP SIGNATURE-----
Merge tag 'amba-make-remove-return-void' of https://git.pengutronix.de/git/ukl/linux into devel-stable
Tag for adaptions to struct amba_driver::remove changing prototype
When executing a tracepoint, the tracepoint's func is dereferenced twice -
in __DO_TRACE() (where the returned pointer is checked) and later on in
__traceiter_##_name where the returned pointer is dereferenced without
checking which leads to races against tracepoint_removal_sync() and
crashes.
This adds a check before referencing the pointer in tracepoint_ptr_deref.
Link: https://lkml.kernel.org/r/20210202072326.120557-1-aik@ozlabs.ru
Cc: stable@vger.kernel.org
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
- failed reconnect fixes (Chao Leng)
- various tracing improvements (Michal Krakowiak, Johannes Thumshirn)
- switch the nvmet-fc assoc_list to use RCU protection (Leonid Ravich)
- resync the status codes with the latest spec (Max Gurtovoy)
- minor nvme-tcp improvements (Sagi Grimberg)
- various cleanups (Rikard Falkeborn, Minwoo Im, Chaitanya Kulkarni,
Israel Rukshin)
-----BEGIN PGP SIGNATURE-----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=mwWd
-----END PGP SIGNATURE-----
Merge tag 'nvme-5.21-2020-02-02' of git://git.infradead.org/nvme into for-5.12/drivers
Pull NVMe updates from Christoph:
"nvme updates for 5.12:
- failed reconnect fixes (Chao Leng)
- various tracing improvements (Michal Krakowiak, Johannes Thumshirn)
- switch the nvmet-fc assoc_list to use RCU protection (Leonid Ravich)
- resync the status codes with the latest spec (Max Gurtovoy)
- minor nvme-tcp improvements (Sagi Grimberg)
- various cleanups (Rikard Falkeborn, Minwoo Im, Chaitanya Kulkarni,
Israel Rukshin)"
* tag 'nvme-5.21-2020-02-02' of git://git.infradead.org/nvme: (22 commits)
nvme-tcp: use cancel tagset helper for tear down
nvme-rdma: use cancel tagset helper for tear down
nvme-tcp: add clean action for failed reconnection
nvme-rdma: add clean action for failed reconnection
nvme-core: add cancel tagset helpers
nvme-core: get rid of the extra space
nvme: add tracing of zns commands
nvme: parse format nvm command details when tracing
nvme: update enumerations for status codes
nvmet: add lba to sect conversion helpers
nvmet: remove extra variable in identify ns
nvmet: remove extra variable in id-desclist
nvmet: remove extra variable in smart log nsid
nvme: refactor ns->ctrl by request
nvme-tcp: pass multipage bvec to request iov_iter
nvme-tcp: get rid of unused helper function
nvme-tcp: fix wrong setting of request iov_iter
nvme: support command retry delay for admin command
nvme: constify static attribute_group structs
nvmet-fc: use RCU proctection for assoc_list
...
The previous commit adding new sysfs for keyboard language has warning and
few code correction has to be done as per new review comments.
Below changes has been addressed in this version:
- corrected warning. Many thanks to kernel test robot <lkp@intel.com> for
reporting and determining this warning.
- used sysfs_emit_at() API instead of strcat.
- sorted keyboard language array.
- removed unwanted space and corrected sentences.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nitin Joshi <njoshi1@lenovo.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210202003210.91773-1-njoshi1@lenovo.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit d7cbe2773a ("platform/x86: thinkpad_acpi: set keyboard language")
adds information on keyboard setting to the thinkpad documentation, but
made the subsection title underline too short.
Hence, make htmldocs warns:
Documentation/admin-guide/laptops/thinkpad-acpi.rst:1472: \
WARNING: Title underline too short.
Rectify length of subsection title underline.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210129040849.26740-1-lukas.bulwahn@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
All recent ThinkPad BIOS-es support the GSKL method used to query the
keyboard-layout used by the ECFW for the SHIFT + other-key key-press
emulation for special keys such as e.g. the '=', '(' and ')' keys
above the numpad on 15" models.
So just checking for the method is not a good indicator of the
model supporting getting/setting the keyboard_lang.
On models where this is not supported GSKL succeeds, but it returns
METHOD_ERR in the returned integer to indicate that this is not
supported on this model.
Add a check for METHOD_ERR and return -ENODEV if it is set to
avoid registering a non-working keyboard_lang sysfs-attr on models
where this is not supported.
Cc: Nitin Joshi <njoshi1@lenovo.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210125205258.135664-1-hdegoede@redhat.com
Sleeping while atomic = bad. Let's fix an obvious typo to try to avoid it.
The warning that was seen (on a downstream kernel with the problematic
patch backported):
BUG: sleeping function called from invalid context at mm/page_alloc.c:4726
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 9, name: ksoftirqd/0
CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 5.4.93-12508-gc10c93e28e39 #1
Call trace:
dump_backtrace+0x0/0x154
show_stack+0x20/0x2c
dump_stack+0xa0/0xfc
___might_sleep+0x11c/0x12c
__might_sleep+0x50/0x84
__alloc_pages_nodemask+0xf8/0x2bc
__arm_lpae_alloc_pages+0x48/0x1b4
__arm_lpae_map+0x124/0x274
__arm_lpae_map+0x1cc/0x274
arm_lpae_map+0x140/0x170
arm_smmu_map+0x78/0xbc
__iommu_map+0xd4/0x210
_iommu_map+0x4c/0x84
iommu_map_atomic+0x44/0x58
__iommu_dma_map+0x8c/0xc4
iommu_dma_map_page+0xac/0xf0
Fixes: d8c1df02ac ("iommu: Move iotlb_sync_map out from __iommu_map")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210201170611.1.I64a7b62579287d668d7c89e105dcedf45d641063@changeid
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pulls in updates in the internal headers from OP-TEE OS [1]. A few
defines has been shortened, hence the changes in rpc.c. Defines not used
by the driver in tee_rpc_cmd.h has been filtered out.
Note that this does not change the ABI.
Link: [1] https://github.com/OP-TEE/optee_os
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Use flexible-array member introduced in C99 instead of zero-length
array. Most of zero-length array was already taken care in previous
patch [1]. Now modified few more cases which were not handled earlier.
[1]. https://patchwork.kernel.org/patch/11394197/
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
trace_qi_submit() could be used when interrupt remapping is supported,
but DMA remapping is not. In this case, the following compile error
occurs.
../drivers/iommu/intel/dmar.c: In function 'qi_submit_sync':
../drivers/iommu/intel/dmar.c:1311:3: error: implicit declaration of function 'trace_qi_submit';
did you mean 'ftrace_nmi_exit'? [-Werror=implicit-function-declaration]
trace_qi_submit(iommu, desc[i].qw0, desc[i].qw1,
^~~~~~~~~~~~~~~
ftrace_nmi_exit
Fixes: f2dd871799 ("iommu/vt-d: Add qi_submit trace event")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210130151907.3929148-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
DT properties "dmic-mode" and "mic-type-X" are optional. Reduces the
log verbosity and changes the message a bit to avoid misleading.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210202033557.1621029-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixup BE DAI links channel count to match topology settings. Normally the
channel count of BE is equal to FE's so we don't have any issue. For some
cases like DSM with 2-channel FE and 4-channel BE the mismatch of BE and
topology will result in audio issues.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Keyon Jie <yang.jie@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210201092345.1214232-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of assigning the needed functions for each driver separately do it
only once in amba_bustype. Move the definition of the functions to their
proper place among the other callbacks used there. Note that the bus's
shutdown function might be called for unbound devices, too, so it needs
additional guarding.
This prepares getting rid of these callbacks in struct device_driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
vfio_platform_remove_common() cannot return non-NULL in
vfio_amba_remove() as the latter is only called if vfio_amba_probe()
returned success.
Diagnosed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20210126165835.687514-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Put helpers (here: amba_get_enable_pclk and amba_put_disable_pclk) at
the top of the file and then define callbacks directly before the
structs they are used in; in the same order.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Consider an amba driver with a .probe but without a .remove callback (e.g.
pl061_gpio_driver). The function amba_probe() is called to bind a device
and so dev_pm_domain_attach() and others are called. As there is no remove
callback amba_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use the core driver callbacks and handle missing amba
callbacks there. For probe refuse registration as a driver without probe
doesn't make sense.
Fixes: 7cfe249475 ("ARM: AMBA: Add pclk support to AMBA bus infrastructure")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmAYD/QQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNLZjCACBK2bCmkVJfs39YeeMhHWVRyiiMpIuCvja
7WuIqeXnbtAg19hkwPqns+XYeTTnoeo/aSZUS9z8DIDUqADMES+1UUMfVf2mfL3A
VD1pGRtQezYS+rDOc5dL9m1CcJ2RRY5tfQEjK8Fnm5CItvylNXbURH1nfu1tMVW7
fn1tMNKCTnY7FkABttKyR4a1XIyFX+fPdSrqd5PjQ7D6rK2ZYrorMf55WpmQEfFu
3er4F3Xz8nJeTvswPUMNB3ibvcdICM9VcSwFHpElTq2dbHUDDz3uFQwyiXrutEmb
Xz4UGabjS/ZEPaty6y7VxdYEbD4Q2dzii57jKKtV49N36iCvkSR2
=5KXT
-----END PGP SIGNATURE-----
Merge tag 'arm-smmu-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into arm/smmu
Arm SMMU updates for 5.12
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
Simplify the frontbuffer unpin by removing the lock requirement. The LRU
bumping was primarily to protect the GTT from being evicted and from
frontbuffers being eagerly shrunk. Now we protect frontbuffers from the
shrinker, and we avoid accidentally evicting from the GTT, so the
benefit from bumping LRU is no more, and we can save more time by not.
Reported-and-tested-by: Matti Hämäläinen <ccr@tnsp.org>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2905
Fixes: c1793ba86a ("drm/i915: Add ww locking to pin_to_display_plane, v2.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119214336.1463-6-chris@chris-wilson.co.uk
(cherry picked from commit 14ca83eece)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If we enable_breadcrumbs for a request while that request is being
removed from HW; we may see that the request is active as we take the
ce->signal_lock and proceed to attach the request to ce->signals.
However, during unsubmission after marking the request as inactive, we
see that the request has not yet been added to ce->signals and so skip
the removal. Pull the check during cancel_breadcrumbs under the same
spinlock as enabling so that we the two tests are consistent in
enable/cancel.
Otherwise, we may insert a request onto ce->signals that we expect should
not be there:
intel_context_remove_breadcrumbs:488 GEM_BUG_ON(!__i915_request_is_complete(rq))
While updating, we can note that we are always called with
irqs-disabled, due to the engine->active.lock being held at the single
caller, and so remove the irqsave/restore making it symmetric to
enable_breadcrumbs.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2931
Fixes: c18636f763 ("drm/i915: Remove requirement for holding i915_request.lock for breadcrumbs")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Cc: <stable@vger.kernel.org> # v5.10+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119162057.31097-1-chris@chris-wilson.co.uk
(cherry picked from commit e7004ea4f5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If while we are cancelling the breadcrumb signaling, we find that the
request is already completed, move it to the irq signaler and let it be
signaled.
v2: Tweak reference counting so that we only acquire a new reference on
adding to a signal list, as opposed to a hidden i915_request_put of the
caller's reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201126140407.31952-5-chris@chris-wilson.co.uk
(cherry picked from commit 85cc2917a3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 0138ba5783 ("powerpc/64/signal: Balance return predictor
stack in signal trampoline") changed __kernel_sigtramp_rt64() VDSO and
trampoline code, and introduced a regression in the way glibc's
backtrace()[1] detects the signal-handler stack frame. Apart from the
practical implications, __kernel_sigtramp_rt64() was a VDSO function
with the semantics that it is a function you can call from userspace
to end a signal handling. Now this semantics are no longer valid.
I believe the aforementioned change affects all releases since 5.9.
This patch tries to fix both the semantics and practical aspect of
__kernel_sigtramp_rt64() returning it to the previous code, whilst
keeping the intended behaviour of 0138ba5783 by adding a new symbol
to serve as the jump target from the kernel to the trampoline. Now the
trampoline has two parts, a new entry point and the old return point.
[1] https://lists.ozlabs.org/pipermail/linuxppc-dev/2021-January/223194.html
Fixes: 0138ba5783 ("powerpc/64/signal: Balance return predictor stack in signal trampoline")
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Raoni Fassina Firmino <raoni@linux.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor tweaks to change log formatting, add stable tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210201200505.iz46ubcizipnkcxe@work-tp
Prevent the ICL HDR plane pipeline from performing YUV color range
correction twice when the input is in limited range. This is done by
removing the limited-range code from icl_program_input_csc().
Before this patch the following could happen: user space gives us a YUV
buffer in limited range; per the pipeline in [1], the plane would first
go through a "YUV Range correct" stage that expands the range; the plane
would then go through the "Input CSC" stage which would also expand the
range because icl_program_input_csc() would use a matrix and an offset
that assume limited-range input; this would ultimately cause dark and
light colors to appear darker and lighter than they should respectively.
This is an issue because if a buffer switches between being scanned out
and being composited with the GPU, the user will see a color difference.
If this switching happens quickly and frequently, the user will perceive
this as a flickering.
[1] https://01.org/sites/default/files/documentation/intel-gfx-prm-osrc-icllp-vol12-displayengine_0.pdf#page=281
Cc: stable@vger.kernel.org
Signed-off-by: Andres Calderon Jaramillo <andrescj@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215224219.3896256-1-andrescj@google.com
(cherry picked from commit fed3875720)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210202084553.30691-1-ville.syrjala@linux.intel.com
This forces reading the base folded state anytime the device is
probed, to make sure it's in sync.
This is useful after a reboot, if the device re-enumerates for
any reason (e.g. ESD shock), or if the driver is unbound/rebound
(debugging/testing).
Without this, the tablet switch state is only synchronized after a
key is pressed (since the device would then send a report that
includes the switch state), leading to strange UX (e.g. UI
mode changes when a key is pressed after reboot).
This is not a problem on detachable base attach, as the device,
by itself, sends a report after it is booted up.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A typical USB keyboard usually splits its keys into several reports:
- one for the basic alphanumeric keys, modifier keys, F<n> keys, six pack
keys and keypad. This report's application is normally listed as
GenericDesktop.Keyboard
- a GenericDesktop.SystemControl report for the system control keys, such
as power and sleep
- Consumer.ConsumerControl report for multimedia (forward, rewind,
play/pause, mute, etc) and other extended keys.
- additional output, vendor specific, and feature reports
Splitting each report into a separate input device is wasteful and even
hurts userspace as it makes it harder to determine the true capabilities
(set of available keys) of a keyboard, so let's adjust application
matching to merge system control and consumer control reports with
keyboard report, if one has already been processed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Redirect my older email addresses that are in the git logs.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested both with Corsairs firmware 11.3 and 13.0 for the Corsairs MP600
and both have the issue as reported by the kernel.
nvme nvme0: missing or invalid SUBNQN field.
Signed-off-by: Claus Stovgaard <claus.stovgaard@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds audio jack injection feature through debugfs, with
this feature, we could validate alsa userspace changes by injecting
plugin or plugout events to the non-phantom audio jacks.
With this change, the sound core will build the folders
$debugfs_mount_dir/sound/cardN if SND_DEBUG and DEBUG_FS are enabled.
And if users also enable the SND_JACK_INJECTION_DEBUG, the jack
injection nodes will be built in the folder cardN like below:
$tree $debugfs_mount_dir/sound
$debugfs_mount_dir/sound
├── card0
│ ├── HDMI_DP_pcm_10_Jack
│ │ ├── jackin_inject
│ │ ├── kctl_id
│ │ ├── mask_bits
│ │ ├── status
│ │ ├── sw_inject_enable
│ │ └── type
...
│ └── HDMI_DP_pcm_9_Jack
│ ├── jackin_inject
│ ├── kctl_id
│ ├── mask_bits
│ ├── status
│ ├── sw_inject_enable
│ └── type
└── card1
├── HDMI_DP_pcm_5_Jack
│ ├── jackin_inject
│ ├── kctl_id
│ ├── mask_bits
│ ├── status
│ ├── sw_inject_enable
│ └── type
...
├── Headphone_Jack
│ ├── jackin_inject
│ ├── kctl_id
│ ├── mask_bits
│ ├── status
│ ├── sw_inject_enable
│ └── type
└── Headset_Mic_Jack
├── jackin_inject
├── kctl_id
├── mask_bits
├── status
├── sw_inject_enable
└── type
The nodes kctl_id, mask_bits, status and type are read-only, users
could check jack or jack_kctl's information through them.
The nodes sw_inject_enable and jackin_inject are directly used for
injection. The sw_inject_enable is read-write, users could check if
software injection is enabled or not on this jack, and users could
echo 1 or 0 to enable or disable software injection on this jack. Once
the injection is enabled, the jack will not change by hardware events
anymore, once the injection is disabled, the jack will restore the
last reported hardware events to the jack. The jackin_inject is
write-only, if the injection is enabled, users could echo 1 or 0 to
this node to inject plugin or plugout events to this jack.
For the detailed usage information on these nodes, please refer to
Documentation/sound/designs/jack-injection.rst.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210127085639.74954-2-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Output loopback is a feature where you can record what you hear.
The HDSP series of the RME interfaces provides this functionality
at the hardware level and this patch exposes controls to enable or
disable it per output (playback) channel.
This probably works on other cards but due to a lack of hardware
it is only tested and enabled for the HDSP9632 card with this patch.
Should this patch be accepted a separate patch will be posted to
https://github.com/alsa-project/alsa-tools/tree/master/hdspmixer
which adds "LPBK" buttons to each output in the playback strip for
the user to be able to control this feature from the user land.
Users from Windows tool TotalMixFX should be familiar with this.
Signed-off-by: Jasmin Fazlic <superfassl@gmail.com>
Link: https://lore.kernel.org/r/95cb3117-e85a-51a6-c2ce-bf736e70fc4c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use nvme_cancel_tagset and nvme_cancel_admin_tagset to clean code for
tear down process.
Signed-off-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
