Add try-lock for exclusive operation start to allow callers to do more
checks. The same operation must already be running. The try-lock and
unlock must pair and are a substitute for btrfs_exclop_start, thus it
must also pair with btrfs_exclop_finish to release the exclop context.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add support code that will allow canceling relocation on the chunk
granularity. This is different and independent of balance, that also
uses relocation but is a higher level operation and manages it's own
state and pause/cancellation requests.
Relocation is used for resize (shrink) and device deletion so this will
be a common point to implement cancellation for both. The context is
entirely in btrfs_relocate_block_group and btrfs_recover_relocation,
enclosing one chunk relocation. The status bit is set and unset between
the chunks. As relocation can take long, the effects may not be
immediate and the request and actual action can slightly race.
The fs_info::reloc_cancel_req is only supposed to be increased and does
not pair with decrement like fs_info::balance_cancel_req.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The exclusive operation is now atomically checked and set using bit
operations. Switch it to protection by spinlock. The super block lock is
not frequently used and adding a new lock seems like an overkill so it
should be safe to reuse it.
The reason to use spinlock is to enhance the locking context so more
checks can be done, eg. allowing the same exclusive operation enter
the exclop section and cancel the running one. This will be used for
resize and device delete.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Move header offsetof() to the expression that calculates the address so
it's part of get_eb_offset_in_page where the 2nd parameter is the member
offset.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The verification copies the calculated checksum bytes to a temporary
buffer but this is not necessary. We can map the eb header on the first
page and use the checksum bytes directly.
This saves at least one function call and boundary checks so it could
lead to a minor performance improvement.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The s_id is already printed by message helpers.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Several members of compressed_bio are of type that's unnecessarily big
for the values that they'd hold:
- the size of the uncompressed and compressed data is 128K now, we can
keep is as int
- same for number of pages
- the compress type fits to a byte
- the errors is 0/1
The size of the unpatched structure is 80 bytes with several holes.
Reordering nr_pages next to the pages the hole after pending_bios is
filled and the resulting size is 56 bytes. This keeps the csums array
aligned to 8 bytes, which is nice. Further size optimizations may be
possible but right now it looks good to me:
struct compressed_bio {
refcount_t pending_bios; /* 0 4 */
unsigned int nr_pages; /* 4 4 */
struct page * * compressed_pages; /* 8 8 */
struct inode * inode; /* 16 8 */
u64 start; /* 24 8 */
unsigned int len; /* 32 4 */
unsigned int compressed_len; /* 36 4 */
u8 compress_type; /* 40 1 */
u8 errors; /* 41 1 */
/* XXX 2 bytes hole, try to pack */
int mirror_num; /* 44 4 */
struct bio * orig_bio; /* 48 8 */
u8 sums[]; /* 56 0 */
/* size: 56, cachelines: 1, members: 12 */
/* sum members: 54, holes: 1, sum holes: 2 */
/* last cacheline: 56 bytes */
};
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are common values set for the stripe constraints, some of them
are already factored out. Do that for increment and mirror_num as well.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When a log recovery is in progress, lots of operations have to take that
into account, so we keep this status per tree during the operation. Long
time ago error handling revamp patch 79787eaab4 ("btrfs: replace many
BUG_ONs with proper error handling") removed clearing of the status in
an error branch. Add it back as was intended in e02119d5a7 ("Btrfs:
Add a write ahead tree log to optimize synchronous operations").
There are probably no visible effects, log replay is done only during
mount and if it fails all structures are cleared so the stale status
won't be kept.
Fixes: 79787eaab4 ("btrfs: replace many BUG_ONs with proper error handling")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The defrag loop processes leaves in batches and starting transaction for
each. The whole defragmentation on a given root is protected by a bit
but in case the transaction fails, the bit is not cleared
In case the transaction fails the bit would prevent starting
defragmentation again, so make sure it's cleared.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The type of discard_bitmap_bytes and discard_extent_bytes is u64 so the
format should be %llu, though the actual values would hardly ever
overflow to negative values.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
While stress testing our error handling I noticed that sometimes we
would still commit the transaction even though we had aborted the
transaction.
Currently we track if a trans handle has dirtied any metadata, and if it
hasn't we mark the filesystem as having an error (so no new transactions
can be started), but we will allow the current transaction to complete
as we do not mark the transaction itself as having been aborted.
This sounds good in theory, but we were not properly tracking IO errors
in btrfs_finish_ordered_io, and thus committing the transaction with
bogus free space data. This isn't necessarily a problem per-se with the
free space cache, as the other guards in place would have kept us from
accepting the free space cache as valid, but highlights a real world
case where we had a bug and could have corrupted the filesystem because
of it.
This "skip abort on empty trans handle" is nice in theory, but assumes
we have perfect error handling everywhere, which we clearly do not.
Also we do not allow further transactions to be started, so all this
does is save the last transaction that was happening, which doesn't
necessarily gain us anything other than the potential for real
corruption.
Remove this particular bit of code, if we decide we need to abort the
transaction then abort the current one and keep us from doing real harm
to the file system, regardless of whether this specific trans handle
dirtied anything or not.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At btrfs_truncate() where we truncate the inode either to the same size
or to a smaller size, we always set the full sync flag on the inode.
This is needed in case the truncation drops or trims any file extent items
that start beyond or cross the new inode size, so that the next fsync
drops all inode items from the log and scans again the fs/subvolume tree
to find all items that must be logged.
However if the truncation does not drop or trims any file extent items, we
do not need to set the full sync flag and force the next fsync to use the
slow code path. So do not set the full sync flag in such cases.
One use case where it is frequent to do truncations that do not change
the inode size and do not drop any extents (no prealloc extents beyond
i_size) is when running Microsoft's SQL Server inside a Docker container.
One example workload is the one Philipp Fent reported recently, in the
thread with a link below. In this workload a large number of fsyncs are
preceded by such truncate operations.
After this change I constantly get the runtime for that workload from
Philipp to be reduced by about -12%, for example from 184 seconds down
to 162 seconds.
Link: https://lore.kernel.org/linux-btrfs/93c4600e-5263-5cba-adf0-6f47526e7561@in.tum.de/
Tested-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The comment at the top of btrfs_truncate() mentions that csum items are
dropped or truncated to the new i_size, but this is wrong and non sense,
as they are unrelated to the i_size and are located in the csums tree and
not on a tree with inode items (fs/subvolume tree or a log tree). Instead
that claim applies to file extent items, so fix the comment to refer to
them instead.
While at it make the whole comment for the function more descriptive and
follow the kernel doc style.
Tested-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we fail to update the delayed inode we need to abort the transaction,
because we could leave an inode with the improper counts or some other
such corruption behind.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we get an error while looking up the inode item we'll simply bail
without cleaning up the delayed node. This results in this style of
warning happening on commit:
WARNING: CPU: 0 PID: 76403 at fs/btrfs/delayed-inode.c:1365 btrfs_assert_delayed_root_empty+0x5b/0x90
CPU: 0 PID: 76403 Comm: fsstress Tainted: G W 5.13.0-rc1+ #373
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
RIP: 0010:btrfs_assert_delayed_root_empty+0x5b/0x90
RSP: 0018:ffffb8bb815a7e50 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff95d6d07e1888 RCX: ffff95d6c0fa3000
RDX: 0000000000000002 RSI: 000000000029e91c RDI: ffff95d6c0fc8060
RBP: ffff95d6c0fc8060 R08: 00008d6d701a2c1d R09: 0000000000000000
R10: ffff95d6d1760ea0 R11: 0000000000000001 R12: ffff95d6c15a4d00
R13: ffff95d6c0fa3000 R14: 0000000000000000 R15: ffffb8bb815a7e90
FS: 00007f490e8dbb80(0000) GS:ffff95d73bc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6e75555cb0 CR3: 00000001101ce001 CR4: 0000000000370ef0
Call Trace:
btrfs_commit_transaction+0x43c/0xb00
? finish_wait+0x80/0x80
? vfs_fsync_range+0x90/0x90
iterate_supers+0x8c/0x100
ksys_sync+0x50/0x90
__do_sys_sync+0xa/0x10
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Because the iref isn't dropped and this leaves an elevated node->count,
so any release just re-queues it onto the delayed inodes list. Fix this
by going to the out label to handle the proper cleanup of the delayed
node.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Right now we only cleanup the delayed iref if we have
BTRFS_DELAYED_NODE_DEL_IREF set on the node. However we have some error
conditions that need to cleanup the iref if it still exists, so to make
this code cleaner move the test_bit into btrfs_release_delayed_iref
itself and unconditionally call it in each of the cases instead.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add sysfs interface to limit io during scrub. We relied on the ionice
interface to do that, eg. the idle class let the system usable while
scrub was running. This has changed when mq-deadline got widespread and
did not implement the scheduling classes. That was a CFQ thing that got
deleted. We've got numerous complaints from users about degraded
performance.
Currently only BFQ supports that but it's not a common scheduler and we
can't ask everybody to switch to it.
Alternatively the cgroup io limiting can be used but that also a
non-trivial setup (v2 required, the controller must be enabled on the
system). This can still be used if desired.
Other ideas that have been explored: piggy-back on ionice (that is set
per-process and is accessible) and interpret the class and classdata as
bandwidth limits, but this does not have enough flexibility as there are
only 8 allowed and we'd have to map fixed limits to each value. Also
adjusting the value would need to lookup the process that currently runs
scrub on the given device, and the value is not sticky so would have to
be adjusted each time scrub runs.
Running out of options, sysfs does not look that bad:
- it's accessible from scripts, or udev rules
- the name is similar to what MD-RAID has
(/proc/sys/dev/raid/speed_limit_max or /sys/block/mdX/md/sync_speed_max)
- the value is sticky at least for filesystem mount time
- adjusting the value has immediate effect
- sysfs is available in constrained environments (eg. system rescue)
- the limit also applies to device replace
Sysfs:
- raw value is in bytes
- values written to the file accept suffixes like K, M
- file is in the per-device directory /sys/fs/btrfs/FSID/devinfo/DEVID/scrub_speed_max
- 0 means use default priority of IO
The scheduler is a simple deadline one and the accuracy is up to nearest
128K.
Signed-off-by: David Sterba <dsterba@suse.com>
To be able to construct a zone append bio we need to look up the
btrfs_device. The code doing the chunk map lookup to get the device is
present in btrfs_submit_compressed_write and submit_extent_page.
Factor out the lookup calls into a helper and use it in the submission
paths.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When inode defrag is canceled, the error is set to EAGAIN but then
overwritten by number of defragmented bytes. As this would hide the
error, rather return EAGAIN. This does not harm 'btrfs fi defrag', it
will print the error and continue to next file (as it does in for any
other error).
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
The io_failure_record::in_validation was introduced to handle failed bio
which cross several sectors. In such case, we still need to verify
which sectors are corrupted.
But since we've changed the way how we handle corrupted sectors, by only
submitting repair for each corrupted sector, there is no need for extra
validation any more.
This patch will cleanup all io_failure_record::in_validation related
code.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently btrfs_submit_read_repair() has some extra check on whether the
failed bio needs extra validation for repair. But we can avoid all
these extra mechanisms if we submit the repair for each sector.
By this, each read repair can be easily handled without the need to
verify which sector is corrupted.
This will also benefit subpage, as one subpage bvec can contain several
sectors, making the extra verification more complex.
So this patch will:
- Introduce repair_one_sector()
The main code submitting repair, which is more or less the same as old
btrfs_submit_read_repair().
But this time, it only repairs one sector.
- Make btrfs_submit_read_repair() to handle sectors differently
There are 3 different cases:
* Good sector
We need to release the page and extent, set the range uptodate.
* Bad sector and failed to submit repair bio
We need to release the page and extent, but not set the range
uptodate.
* Bad sector but repair bio submitted
The page and extent release will be handled by the submitted repair
bio. Nothing needs to be done.
Since btrfs_submit_read_repair() will handle the page and extent
release now, we need to skip to next bvec even we hit some error.
- Change the lifespan of @uptodate in end_bio_extent_readpage()
Since now btrfs_submit_read_repair() will handle the full bvec
which contains any corruption, we don't need to bother updating
@uptodate bit anymore.
Just let @uptodate to be local variable inside the main loop,
so that any error from one bvec won't affect later bvec.
- Only export btrfs_repair_one_sector(), unexport
btrfs_submit_read_repair()
The only outside caller for read repair is DIO, which already submits
its repair for just one sector.
Only export btrfs_repair_one_sector() for DIO.
This patch will focus on the change on the repair path, the extra
validation code is still kept as is, and will be cleaned up later.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This will provide the basis for later per-sector repair for subpage,
while still keeping the existing code happy.
As if all csums match, the return value will be 0, same as now.
Only when csum mismatches, the return value is different.
The new return value will be a bitmap, for 4K sectorsize and 4K page
size, it will be either 1, instead of the -EIO (which is not used
directly by the callers, no effective change).
But for 4K sectorsize and 64K page size, aka subpage case, since the
bvec can contain multiple sectors, knowing which sectors are corrupted
will allow us to submit repair only for corrupted sectors.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The 'check_async_write' function is a helper used in
'btrfs_submit_metadata_bio' and it checks if asynchronous writing can be
used for metadata.
Make the function return bool and get rid of the local variable async in
btrfs_submit_metadata_bio storing the result of check_async_write's
tests.
As this is touching all function call sites, also rename it to
should_async_write as this is more in line with the naming we use.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we can't read a reliable write pointer from a sequential zone fail
creating the block group with an I/O error.
Also if the read write pointer is beyond the end of the respective zone,
fail the creation of the block group on this zone with an I/O error.
While this could also happen in real world scenarios with misbehaving
drives, this issue addresses a problem uncovered by fstests' test case
generic/475.
CC: stable@vger.kernel.org # 5.12+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This extends patch 784daf2b96 ("btrfs: zoned: sanity check zone
type"), the message was supposed to be there but was lost during merge.
We want to make the error noticeable so add it.
Fixes: 784daf2b96 ("btrfs: zoned: sanity check zone type")
CC: stable@vger.kernel.org # 5.12+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we decide to flush delalloc from the preemptive flusher, we really do
not want to wait on ordered extents, as it gains us nothing. However
there was logic to go ahead and wait on ordered extents if there was
more ordered bytes than delalloc bytes. We do not want this behavior,
so pass through whether this flushing is for preemption, and do not wait
for ordered extents if that's the case. Also break out of the shrink
loop after the first flushing, as we just want to one shot shrink
delalloc.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
While testing heavy delalloc workloads I noticed that sometimes we'd
just stop preemptively flushing when we had loads of delalloc available
to flush. This is because we skip preemptive flushing if delalloc <=
ordered. However if we start with say 4gib of delalloc, and we flush
2gib of that, we'll stop flushing there, when we still have 2gib of
delalloc to flush.
Instead adjust the ordered bytes down by half, this way if 2/3 of our
outstanding delalloc reservations are tied up by ordered extents we
don't bother preemptive flushing, as we're getting close to the state
where we need to wait on ordered extents.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When deciding if we should preemptively flush space, we will add in the
amount of space used by all block rsvs. However this also includes the
global block rsv, which isn't flushable so shouldn't be accounted for in
this calculation. If we decide to use ->bytes_may_use in our used
calculation we need to subtract the global rsv size from this amount so
it most closely matches the flushable space.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We calculate the amount of "free" space available for normal
reservations by taking the total space and subtracting out the hard used
space, which is readonly, used, and reserved space.
However we weren't taking into account the global block rsv, which is
essentially hard used space. Handle this by subtracting it from the
available free space, so that our threshold more closely mirrors
reality.
We need to do the check because it's possible that the global_rsv_size +
used is > total_bytes, sometimes the global reserve can end up being
calculated as larger than the available size (think small filesystems
where we only have the original 8MiB chunk of metadata). It doesn't
usually happen, but that can get us into trouble so this is safer.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Global rsv can't be used for normal allocations, and for very full file
systems we can decide to try and async flush constantly even though
there's really not a lot of space to reclaim. Deal with this by
including the global block rsv size in the "total used" calculation.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We were clamping the threshold for preemptive reclaim any time we added
a ticket to wait on, which if we have a lot of threads means we'd
essentially max out the clamp the first time we start to flush.
Instead of doing this, simply do it every time we have to start
flushing, this will make us ramp up gradually instead of going to max
clamping as soon as we start needing to do flushing.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
need_preemptive_reclaim() does some calculations, which aren't heavy,
but if we're already running preemptive reclaim there's no reason to do
them at all, so re-order the checks so that we don't do the calculation
if we're already doing reclaim.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit b2598edf8b ("btrfs: remove unused argument seed from
btrfs_find_device") removed the argument seed from btrfs_find_device
but forgot the comment, so remove it.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Su Yue <l@damenly.su>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
try_lock_extent() returns 1 on success or 0 for failure and not an error
code. If try_lock_extent() fails, read_extent_buffer_subpage() returns
zero indicating subpage extent read success.
Return EAGAIN/EWOULDBLOCK if try_lock_extent() fails in locking the
extent.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
in case of driver wants to sync part of ranges with offset,
swiotlb_tbl_sync_single() copies from orig_addr base to tlb_addr with
offset and ends up with data mismatch.
It was removed from
"swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single",
but said logic has to be added back in.
From Linus's email:
"That commit which the removed the offset calculation entirely, because the old
(unsigned long)tlb_addr & (IO_TLB_SIZE - 1)
was wrong, but instead of removing it, I think it should have just
fixed it to be
(tlb_addr - mem->start) & (IO_TLB_SIZE - 1);
instead. That way the slot offset always matches the slot index calculation."
(Unfortunatly that broke NVMe).
The use-case that drivers are hitting is as follow:
1. Get dma_addr_t from dma_map_single()
dma_addr_t tlb_addr = dma_map_single(dev, vaddr, vsize, DMA_TO_DEVICE);
|<---------------vsize------------->|
+-----------------------------------+
| | original buffer
+-----------------------------------+
vaddr
swiotlb_align_offset
|<----->|<---------------vsize------------->|
+-------+-----------------------------------+
| | | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
2. Do something
3. Sync dma_addr_t through dma_sync_single_for_device(..)
dma_sync_single_for_device(dev, tlb_addr + offset, size, DMA_TO_DEVICE);
Error case.
Copy data to original buffer but it is from base addr (instead of
base addr + offset) in original buffer:
swiotlb_align_offset
|<----->|<- offset ->|<- size ->|
+-------+-----------------------------------+
| | |##########| | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
|<- size ->|
+-----------------------------------+
|##########| | original buffer
+-----------------------------------+
vaddr
The fix is to copy the data to the original buffer and take into
account the offset, like so:
swiotlb_align_offset
|<----->|<- offset ->|<- size ->|
+-------+-----------------------------------+
| | |##########| | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
|<- offset ->|<- size ->|
+-----------------------------------+
| |##########| | original buffer
+-----------------------------------+
vaddr
[One fix which was Linus's that made more sense to as it created a
symmetry would break NVMe. The reason for that is the:
unsigned int offset = (tlb_addr - mem->start) & (IO_TLB_SIZE - 1);
would come up with the proper offset, but it would lose the
alignment (which this patch contains).]
Fixes: 16fc3cef33 ("swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single")
Signed-off-by: Bumyong Lee <bumyong.lee@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Dominique MARTINET <dominique.martinet@atmark-techno.com>
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
H_RPT_INVALIDATE does two types of TLB invalidations:
1. Process-scoped invalidations for guests when LPCR[GTSE]=0.
This is currently not used in KVM as GTSE is not usually
disabled in KVM.
2. Partition-scoped invalidations that an L1 hypervisor does on
behalf of an L2 guest. This is currently handled
by H_TLB_INVALIDATE hcall and this new replaces the old that.
This commit enables process-scoped invalidations for L1 guests.
Support for process-scoped and partition-scoped invalidations
from/for nested guests will be added separately.
Process scoped tlbie invalidations from L1 and nested guests
need RS register for TLBIE instruction to contain both PID and
LPID. This patch introduces primitives that execute tlbie
instruction with both PID and LPID set in prepartion for
H_RPT_INVALIDATE hcall.
A description of H_RPT_INVALIDATE follows:
int64 /* H_Success: Return code on successful completion */
/* H_Busy - repeat the call with the same */
/* H_Parameter, H_P2, H_P3, H_P4, H_P5 : Invalid
parameters */
hcall(const uint64 H_RPT_INVALIDATE, /* Invalidate RPT
translation
lookaside information */
uint64 id, /* PID/LPID to invalidate */
uint64 target, /* Invalidation target */
uint64 type, /* Type of lookaside information */
uint64 pg_sizes, /* Page sizes */
uint64 start, /* Start of Effective Address (EA)
range (inclusive) */
uint64 end) /* End of EA range (exclusive) */
Invalidation targets (target)
-----------------------------
Core MMU 0x01 /* All virtual processors in the
partition */
Core local MMU 0x02 /* Current virtual processor */
Nest MMU 0x04 /* All nest/accelerator agents
in use by the partition */
A combination of the above can be specified,
except core and core local.
Type of translation to invalidate (type)
---------------------------------------
NESTED 0x0001 /* invalidate nested guest partition-scope */
TLB 0x0002 /* Invalidate TLB */
PWC 0x0004 /* Invalidate Page Walk Cache */
PRT 0x0008 /* Invalidate caching of Process Table
Entries if NESTED is clear */
PAT 0x0008 /* Invalidate caching of Partition Table
Entries if NESTED is set */
A combination of the above can be specified.
Page size mask (pages)
----------------------
4K 0x01
64K 0x02
2M 0x04
1G 0x08
All sizes (-1UL)
A combination of the above can be specified.
All page sizes can be selected with -1.
Semantics: Invalidate radix tree lookaside information
matching the parameters given.
* Return H_P2, H_P3 or H_P4 if target, type, or pageSizes parameters
are different from the defined values.
* Return H_PARAMETER if NESTED is set and pid is not a valid nested
LPID allocated to this partition
* Return H_P5 if (start, end) doesn't form a valid range. Start and
end should be a valid Quadrant address and end > start.
* Return H_NotSupported if the partition is not in running in radix
translation mode.
* May invalidate more translation information than requested.
* If start = 0 and end = -1, set the range to cover all valid
addresses. Else start and end should be aligned to 4kB (lower 11
bits clear).
* If NESTED is clear, then invalidate process scoped lookaside
information. Else pid specifies a nested LPID, and the invalidation
is performed on nested guest partition table and nested guest
partition scope real addresses.
* If pid = 0 and NESTED is clear, then valid addresses are quadrant 3
and quadrant 0 spaces, Else valid addresses are quadrant 0.
* Pages which are fully covered by the range are to be invalidated.
Those which are partially covered are considered outside
invalidation range, which allows a caller to optimally invalidate
ranges that may contain mixed page sizes.
* Return H_SUCCESS on success.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-4-bharata@linux.ibm.com
Add a field to mmu_psize_def to store the page size encodings
of H_RPT_INVALIDATE hcall. Initialize this while scanning the radix
AP encodings. This will be used when invalidating with required
page size encoding in the hcall.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-3-bharata@linux.ibm.com
The type values H_RPTI_TYPE_PRT and H_RPTI_TYPE_PAT indicate
invalidating the caching of process and partition scoped entries
respectively.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210621085003.904767-2-bharata@linux.ibm.com
The kernel and the user obtain an xattr value in two different ways:
kernel (EVM): uses vfs_getxattr_alloc() which obtains the xattr value from
the filesystem handler (raw value);
user (ima-evm-utils): uses vfs_getxattr() which obtains the xattr value
from the LSMs (normalized value).
Normally, this does not have an impact unless security.selinux is set with
setfattr, with a value not terminated by '\0' (this is not the recommended
way, security.selinux should be set with the appropriate tools such as
chcon and restorecon).
In this case, the kernel and the user see two different xattr values: the
former sees the xattr value without '\0' (raw value), the latter sees the
value with '\0' (value normalized by SELinux).
This could result in two different verification outcomes from EVM and
ima-evm-utils, if a signature was calculated with a security.selinux value
terminated by '\0' and the value set in the filesystem is not terminated by
'\0'. The former would report verification failure due to the missing '\0',
while the latter would report verification success (because it gets the
normalized value with '\0').
This patch mitigates this issue by comparing in evm_calc_hmac_or_hash() the
size of the xattr returned by the two xattr functions and by warning the
user if there is a discrepancy.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Suggested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.
Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.
Add support for over and under voltage detection for Vout1 ... Vout4
and VoutL1. Add over-current detection for VoutS1 and finally a
thermal warning (common for all regulators) which alerts 30 C
before temperature reaches the thermal shutdown point. This way
consumer drivers can build error-recovery mechanisms.
Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/05c4f7a8e30ef1d4d5f3ceab07da4ebe68f5b4ed.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BD9576MUF provides over-current protection and detection. Current is
measured as voltage loss over external FET. Allow specifying FET's on
resistance so current monitoring limits can be converted to voltages.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/e5feb160d7e09f33fff5b88f1928c66a15c6680f.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide helper function for IC's implementing regulator notifications
when an IRQ fires. The helper also works for IRQs which can not be acked.
Helper can be set to disable the IRQ at handler and then re-enabling it
on delayed work later. The helper also adds regulator_get_error_flags()
errors in cache for the duration of IRQ disabling.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/ebdf86d8c22b924667ec2385330e30fcbfac0119.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rdev print helpers are a nice way to print messages related to a
specific regulator device. Move them from core.c to internal.h
As the rdev print helpers use rdev_get_name() export it from core.c. Also
move the declaration from coupler.h to driver.h because the rdev name is
not just a coupled regulator property. I guess the main audience for
rdev_get_name() will be the regulator core and drivers.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/dc7fd70dc31de4d0e820b7646bb78eeb04f80735.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 'warning' level events and error flags to regulator core.
Current regulator core notifications are used to inform consumers
about errors where HW is misbehaving in such way it is assumed to
be broken/unrecoverable.
There are PMICs which are designed for system(s) that may have use
for regulator indications sent before HW is damaged so that some
board/consumer specific recovery-event can be performed while
continuing most of the normal operations.
Add new WARNING level events and notifications to be used for
that purpose.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9b54aa5589ae4b5945d53d114bac3fae55fa4818.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
