Running devlink reload command for port in switchdev mode cause
resources to corrupt: driver can't release allocated EQ and reclaim
memory pages, because "rdma" auxiliary device had add CQs which blocks
EQ from deletion.
Erroneous sequence happens during reload-down phase, and is following:
1. detach device - suspends auxiliary devices which support it, destroys
others. During this step "eth-rep" and "rdma-rep" are destroyed,
"eth" - suspended.
2. disable SRIOV - moves device to legacy mode; as part of disablement -
rescans drivers. This step adds "rdma" auxiliary device.
3. destroy EQ table - <failure>.
Driver shouldn't create any device during unload flows. To handle that
implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset
on device attach. If flag is set do no-op on drivers rescan.
Fixes: a925b5e309 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Attempting to boot 32-bit ARM kernels under QEMU's 3.x virt models fails
when we have more than 512M of RAM in the model as we run out of vmalloc
space for the PCI ECAM regions. This failure will be silent when running
libvirt, as the console in that situation is a PCI device.
In this configuration, the kernel maps the whole ECAM, which QEMU sets up
for 256 buses, even when maybe only seven buses are in use. Each bus uses
1M of ECAM space, and ioremap() adds an additional guard page between
allocations. The kernel vmap allocator will align these regions to 512K,
resulting in each mapping eating 1.5M of vmalloc space. This means we need
384M of vmalloc space just to map all of these, which is very wasteful of
resources.
Fix this by only mapping the ECAM for buses we are going to be using. In
my setups, this is around seven buses in most guests, which is 10.5M of
vmalloc space - way smaller than the 384M that would otherwise be required.
This also means that the kernel can boot without forcing extra RAM into
highmem with the vmalloc= argument, or decreasing the virtual RAM available
to the guest.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/E1lhCAV-0002yb-50@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
There is a race between THP unmapping and truncation, when truncate sees
pmd_none() and skips the entry, after munmap's zap_huge_pmd() cleared
it, but before its page_remove_rmap() gets to decrement
compound_mapcount: generating false "BUG: Bad page cache" reports that
the page is still mapped when deleted. This commit fixes that, but not
in the way I hoped.
The first attempt used try_to_unmap(page, TTU_SYNC|TTU_IGNORE_MLOCK)
instead of unmap_mapping_range() in truncate_cleanup_page(): it has
often been an annoyance that we usually call unmap_mapping_range() with
no pages locked, but there apply it to a single locked page.
try_to_unmap() looks more suitable for a single locked page.
However, try_to_unmap_one() contains a VM_BUG_ON_PAGE(!pvmw.pte,page):
it is used to insert THP migration entries, but not used to unmap THPs.
Copy zap_huge_pmd() and add THP handling now? Perhaps, but their TLB
needs are different, I'm too ignorant of the DAX cases, and couldn't
decide how far to go for anon+swap. Set that aside.
The second attempt took a different tack: make no change in truncate.c,
but modify zap_huge_pmd() to insert an invalidated huge pmd instead of
clearing it initially, then pmd_clear() between page_remove_rmap() and
unlocking at the end. Nice. But powerpc blows that approach out of the
water, with its serialize_against_pte_lookup(), and interesting pgtable
usage. It would need serious help to get working on powerpc (with a
minor optimization issue on s390 too). Set that aside.
Just add an "if (page_mapped(page)) synchronize_rcu();" or other such
delay, after unmapping in truncate_cleanup_page()? Perhaps, but though
that's likely to reduce or eliminate the number of incidents, it would
give less assurance of whether we had identified the problem correctly.
This successful iteration introduces "unmap_mapping_page(page)" instead
of try_to_unmap(), and goes the usual unmap_mapping_range_tree() route,
with an addition to details. Then zap_pmd_range() watches for this
case, and does spin_unlock(pmd_lock) if so - just like
page_vma_mapped_walk() now does in the PVMW_SYNC case. Not pretty, but
safe.
Note that unmap_mapping_page() is doing a VM_BUG_ON(!PageLocked) to
assert its interface; but currently that's only used to make sure that
page->mapping is stable, and zap_pmd_range() doesn't care if the page is
locked or not. Along these lines, in invalidate_inode_pages2_range()
move the initial unmap_mapping_range() out from under page lock, before
then calling unmap_mapping_page() under page lock if still mapped.
Link: https://lkml.kernel.org/r/a2a4a148-cdd8-942c-4ef8-51b77f643dbe@google.com
Fixes: fc127da085 ("truncate: handle file thp")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stressing huge tmpfs often crashed on unmap_page()'s VM_BUG_ON_PAGE
(!unmap_success): with dump_page() showing mapcount:1, but then its raw
struct page output showing _mapcount ffffffff i.e. mapcount 0.
And even if that particular VM_BUG_ON_PAGE(!unmap_success) is removed,
it is immediately followed by a VM_BUG_ON_PAGE(compound_mapcount(head)),
and further down an IS_ENABLED(CONFIG_DEBUG_VM) total_mapcount BUG():
all indicative of some mapcount difficulty in development here perhaps.
But the !CONFIG_DEBUG_VM path handles the failures correctly and
silently.
I believe the problem is that once a racing unmap has cleared pte or
pmd, try_to_unmap_one() may skip taking the page table lock, and emerge
from try_to_unmap() before the racing task has reached decrementing
mapcount.
Instead of abandoning the unsafe VM_BUG_ON_PAGE(), and the ones that
follow, use PVMW_SYNC in try_to_unmap_one() in this case: adding
TTU_SYNC to the options, and passing that from unmap_page().
When CONFIG_DEBUG_VM, or for non-debug too? Consensus is to do the same
for both: the slight overhead added should rarely matter, except perhaps
if splitting sparsely-populated multiply-mapped shmem. Once confident
that bugs are fixed, TTU_SYNC here can be removed, and the race
tolerated.
Link: https://lkml.kernel.org/r/c1e95853-8bcd-d8fd-55fa-e7f2488e78f@google.com
Fixes: fec89c109f ("thp: rewrite freeze_page()/unfreeze_page() with generic rmap walkers")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most callers of is_huge_zero_pmd() supply a pmd already verified
present; but a few (notably zap_huge_pmd()) do not - it might be a pmd
migration entry, in which the pfn is encoded differently from a present
pmd: which might pass the is_huge_zero_pmd() test (though not on x86,
since L1TF forced us to protect against that); or perhaps even crash in
pmd_page() applied to a swap-like entry.
Make it safe by adding pmd_present() check into is_huge_zero_pmd()
itself; and make it quicker by saving huge_zero_pfn, so that
is_huge_zero_pmd() will not need to do that pmd_page() lookup each time.
__split_huge_pmd_locked() checked pmd_trans_huge() before: that worked,
but is unnecessary now that is_huge_zero_pmd() checks present.
Link: https://lkml.kernel.org/r/21ea9ca-a1f5-8b90-5e88-95fb1c49bbfa@google.com
Fixes: e71769ae52 ("mm: enable thp migration for shmem thp")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The routine restore_reserve_on_error is called to restore reservation
information when an error occurs after page allocation. The routine
alloc_huge_page modifies the mapping reserve map and potentially the
reserve count during allocation. If code calling alloc_huge_page
encounters an error after allocation and needs to free the page, the
reservation information needs to be adjusted.
Currently, restore_reserve_on_error only takes action on pages for which
the reserve count was adjusted(HPageRestoreReserve flag). There is
nothing wrong with these adjustments. However, alloc_huge_page ALWAYS
modifies the reserve map during allocation even if the reserve count is
not adjusted. This can cause issues as observed during development of
this patch [1].
One specific series of operations causing an issue is:
- Create a shared hugetlb mapping
Reservations for all pages created by default
- Fault in a page in the mapping
Reservation exists so reservation count is decremented
- Punch a hole in the file/mapping at index previously faulted
Reservation and any associated pages will be removed
- Allocate a page to fill the hole
No reservation entry, so reserve count unmodified
Reservation entry added to map by alloc_huge_page
- Error after allocation and before instantiating the page
Reservation entry remains in map
- Allocate a page to fill the hole
Reservation entry exists, so decrement reservation count
This will cause a reservation count underflow as the reservation count
was decremented twice for the same index.
A user would observe a very large number for HugePages_Rsvd in
/proc/meminfo. This would also likely cause subsequent allocations of
hugetlb pages to fail as it would 'appear' that all pages are reserved.
This sequence of operations is unlikely to happen, however they were
easily reproduced and observed using hacked up code as described in [1].
Address the issue by having the routine restore_reserve_on_error take
action on pages where HPageRestoreReserve is not set. In this case, we
need to remove any reserve map entry created by alloc_huge_page. A new
helper routine vma_del_reservation assists with this operation.
There are three callers of alloc_huge_page which do not currently call
restore_reserve_on error before freeing a page on error paths. Add
those missing calls.
[1] https://lore.kernel.org/linux-mm/20210528005029.88088-1-almasrymina@google.com/
Link: https://lkml.kernel.org/r/20210607204510.22617-1-mike.kravetz@oracle.com
Fixes: 96b96a96dd ("mm/hugetlb: fix huge page reservation leak in private mapping error paths"
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found it by pure code review, that pte_same_as_swp() of unuse_vma()
didn't take uffd-wp bit into account when comparing ptes.
pte_same_as_swp() returning false negative could cause failure to
swapoff swap ptes that was wr-protected by userfaultfd.
Link: https://lkml.kernel.org/r/20210603180546.9083-1-peterx@redhat.com
Fixes: f45ec5ff16 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [5.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When hugetlb page fault (under overcommitting situation) and
memory_failure() race, VM_BUG_ON_PAGE() is triggered by the following
race:
CPU0: CPU1:
gather_surplus_pages()
page = alloc_surplus_huge_page()
memory_failure_hugetlb()
get_hwpoison_page(page)
__get_hwpoison_page(page)
get_page_unless_zero(page)
zero = put_page_testzero(page)
VM_BUG_ON_PAGE(!zero, page)
enqueue_huge_page(h, page)
put_page(page)
__get_hwpoison_page() only checks the page refcount before taking an
additional one for memory error handling, which is not enough because
there's a time window where compound pages have non-zero refcount during
hugetlb page initialization.
So make __get_hwpoison_page() check page status a bit more for hugetlb
pages with get_hwpoison_huge_page(). Checking hugetlb-specific flags
under hugetlb_lock makes sure that the hugetlb page is not transitive.
It's notable that another new function, HWPoisonHandlable(), is helpful
to prevent a race against other transitive page states (like a generic
compound page just before PageHuge becomes true).
Link: https://lkml.kernel.org/r/20210603233632.2964832-2-nao.horiguchi@gmail.com
Fixes: ead07f6a86 ("mm/memory-failure: introduce get_hwpoison_page() for consistent refcount handling")
Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reported-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org> [5.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Export two functions from GPIO ACPI for wider use
* Clean up Whiskey Cove and Crystal Cove GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- remove platform_set_drvdata() + cleanup probe
gpiolib:
- acpi: Add acpi_gpio_get_io_resource()
- acpi: Introduce acpi_get_and_request_gpiod() helper
wcove:
- Split error handling for CTRL and IRQ registers
- Unify style of to_reg() with to_ireg()
- Use IRQ hardware number getter instead of direct access
-----BEGIN PGP SIGNATURE-----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=WHpx
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.14-1' into review-hans
intel-gpio for v5.14-1
* Export two functions from GPIO ACPI for wider use
* Clean up Whiskey Cove and Crystal Cove GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- remove platform_set_drvdata() + cleanup probe
gpiolib:
- acpi: Add acpi_gpio_get_io_resource()
- acpi: Introduce acpi_get_and_request_gpiod() helper
wcove:
- Split error handling for CTRL and IRQ registers
- Unify style of to_reg() with to_ireg()
- Use IRQ hardware number getter instead of direct access
We can already enable and disable SAM events via one of two ways: either
via a (non-observer) notifier tied to a specific event group, or a
generic event enable/disable request. In some instances, however,
neither method may be desirable.
The first method will tie the event enable request to a specific
notifier, however, when we want to receive notifications for multiple
event groups of the same target category and forward this to the same
notifier callback, we may receive duplicate events, i.e. one event per
registered notifier. The second method will bypass the internal
reference counting mechanism, meaning that a disable request will
disable the event regardless of any other client driver using it, which
may break the functionality of that driver.
To address this problem, add new functions that allow enabling and
disabling of events via the event reference counting mechanism built
into the controller, without needing to register a notifier.
This can then be used in combination with observer notifiers to process
multiple events of the same target category without duplication in the
same callback function.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210604134755.535590-3-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently, each SSAM event notifier is directly tied to one group of
events. This makes sense as registering a notifier will automatically
take care of enabling the corresponding event group and normally drivers
only need notifications for a very limited number of events, associated
with different callbacks for each group.
However, there are rare cases, especially for debugging, when we want to
get notifications for a whole event target category instead of just a
single group of events in that category. Registering multiple notifiers,
i.e. one per group, may be infeasible due to two issues: a) we might not
know every event enable/disable specification as some events are
auto-enabled by the EC and b) forwarding this to the same callback will
lead to duplicate events as we might not know the full event
specification to perform the appropriate filtering.
This commit introduces observer-notifiers, which are notifiers that are
not tied to a specific event group and do not attempt to manage any
events. In other words, they can be registered without enabling any
event group or incrementing the corresponding reference count and just
act as silent observers, listening to all currently/previously enabled
events based on their match-specification.
Essentially, this allows us to register one single notifier for a full
event target category, meaning that we can process all events of that
target category in a single callback without duplication. Specifically,
this will be used in the cdev debug interface to forward events to
user-space via a device file from which the events can be read.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210604134755.535590-2-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The legay ide driver has been replace with libata starting in 2003 and has
been scheduled for removal for a while. Finally kill it off so that we
can start cleaning up various bits of cruft it forced on the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a pre-cursor to some upcoming W=1 fix-ups.
Fixes the following W=1 kernel build warning(s):
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mark Lord <mlord@pobox.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210528090502.1799866-2-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Although first implemented for NVME, this check may be usable by
other drivers as well. Microsoft's specification explicitly mentions
that is may be usable by SATA and AHCI devices. Google also indicates
that they have used this with SDHCI in a downstream kernel tree that
a user can plug a storage device into.
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Suggested-by: Keith Busch <kbusch@kernel.org>
CC: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Prike Liang <prike.liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
CXL is a hotplug bus and arranges for nvdimm devices to be dynamically
discovered and removed. The libnvdimm core manages shutdown of nvdimm
security operations when the device is unregistered. That functionality
is moved to nvdimm_delete() and invoked by the CXL-to-nvdimm glue code.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162379910271.2993820.2955889139842401250.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch enables support for Dell S140 and later controllers
that use Intel's PCHs configured as PCI_CLASS_STORAGE_RAID.
Reviewed-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Charles Rose <charles.rose@dell.com>
Link: https://lore.kernel.org/r/20210615190801.1744466-1-charles.rose@dell.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make dm-writecache wait if the kcopyd workqueue is busy (as will
happen if waiting for page allocation or inside submit_bio).
This change improves performance of "mkfs.ext2" by approximately 20%
on one testbed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511 ("ptp: validate the requested frequency adjustment.")
Fixes: d94ba80ebb ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The Arm FFA specification describes a software architecture to
leverages the virtualization extension to isolate software images
provided by an ecosystem of vendors from each other and describes
interfaces that standardize communication between the various software
images including communication between images in the Secure world and
Normal world. Any Hypervisor could use the FFA interfaces to enable
communication between VMs it manages.
The Hypervisor a.k.a Partition managers in FFA terminology can assign
system resources(Memory regions, Devices, CPU cycles) to the partitions
and manage isolation amongst them.
This is the initial and minimal support for the FFA interface to enable
communication between secure partitions and the normal world OS.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAmC19HAACgkQAEG6vDF+
4pijcw//XugK+jFEN7fA6eFzE7OeGt1xPG2mhG5TF1jtvQv2TQlij50V8evOgJmd
kM3h5pUeEWMt4XrF0I2TlLOglBHLpFbU253kRPRC7zeYxK+AzD6TxtABKZ+eykAk
OEQisX9FMp/h1rnnvu/OqT7l2AH/pZkVIwc2GQi6h+BvQzUq/NPanuuT+rS00U2E
lLfZ98MQIjoUSDKr6r0C83gt8BlUWR62jkIkhsLycwFFouhWrdewXptfOntD4wIs
1pDRi4+qdZLbOeFCLxHR9NfMTdGdnBY//P8NwmnSYV6YnbtVcgwvwyRqMAC6ElJM
Lk+AuqJS+RSCdyqQerjkvVMNSQx778nPsmzEMteOyLCAfr2kXhQ84FfqaJpFBDsJ
GQUUW8H5runR2P4p2Q3Tql9tTt7AhrOuO0iUIxBu5cq4YRBPMBamtRbquJtYN+VH
9ggV4ygbkq4BIKYaBFaVffHOg0ygbvDTkXv/09wRmcGNH12y9AeuLyumhwcWxV0Z
Kk0bjEieTjvisrshOeKOp5eOuhyixhFJNcffAOIos3KIkuQ1ivAL7cIig9fWF+k0
AbqOTvX4dVSdIKBi+Q8op2CZ1gyDi80P43MstTgKlbZ8AN2YWxa9S3Iw27D4gY8u
tIN8PqkB2NctwQecVcGv58JyDlqTRnCcuole7fJWr3iGRdGvyV4=
=DQ7A
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=TfmE
-----END PGP SIGNATURE-----
Merge tag 'arm-ffa-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
Arm Firmware Framework for ARMv8-A(FFA) interface driver
The Arm FFA specification describes a software architecture to
leverages the virtualization extension to isolate software images
provided by an ecosystem of vendors from each other and describes
interfaces that standardize communication between the various software
images including communication between images in the Secure world and
Normal world. Any Hypervisor could use the FFA interfaces to enable
communication between VMs it manages.
The Hypervisor a.k.a Partition managers in FFA terminology can assign
system resources(Memory regions, Devices, CPU cycles) to the partitions
and manage isolation amongst them.
This is the initial and minimal support for the FFA interface to enable
communication between secure partitions and the normal world OS.
* tag 'arm-ffa-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Add support for MEM_* interfaces
firmware: arm_ffa: Setup in-kernel users of FFA partitions
firmware: arm_ffa: Add support for SMCCC as transport to FFA driver
firmware: arm_ffa: Add initial Arm FFA driver support
firmware: arm_ffa: Add initial FFA bus support for device enumeration
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
Link: https://lore.kernel.org/r/20210601095838.GA838783@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch introduces a new bpf_attach_type for BPF_PROG_TYPE_SK_REUSEPORT
to check if the attached eBPF program is capable of migrating sockets. When
the eBPF program is attached, we run it for socket migration if the
expected_attach_type is BPF_SK_REUSEPORT_SELECT_OR_MIGRATE or
net.ipv4.tcp_migrate_req is enabled.
Currently, the expected_attach_type is not enforced for the
BPF_PROG_TYPE_SK_REUSEPORT type of program. Thus, this commit follows the
earlier idea in the commit aac3fc320d ("bpf: Post-hooks for sys_bind") to
fix up the zero expected_attach_type in bpf_prog_load_fixup_attach_type().
Moreover, this patch adds a new field (migrating_sk) to sk_reuseport_md to
select a new listener based on the child socket. migrating_sk varies
depending on if it is migrating a request in the accept queue or during
3WHS.
- accept_queue : sock (ESTABLISHED/SYN_RECV)
- 3WHS : request_sock (NEW_SYN_RECV)
In the eBPF program, we can select a new listener by
BPF_FUNC_sk_select_reuseport(). Also, we can cancel migration by returning
SK_DROP. This feature is useful when listeners have different settings at
the socket API level or when we want to free resources as soon as possible.
- SK_PASS with selected_sk, select it as a new listener
- SK_PASS with selected_sk NULL, fallbacks to the random selection
- SK_DROP, cancel the migration.
There is a noteworthy point. We select a listening socket in three places,
but we do not have struct skb at closing a listener or retransmitting a
SYN+ACK. On the other hand, some helper functions do not expect skb is NULL
(e.g. skb_header_pointer() in BPF_FUNC_skb_load_bytes(), skb_tail_pointer()
in BPF_FUNC_skb_load_bytes_relative()). So we allocate an empty skb
temporarily before running the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201123003828.xjpjdtk4ygl6tg6h@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201203042402.6cskdlit5f3mw4ru@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201209030903.hhow5r53l6fmozjn@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-10-kuniyu@amazon.co.jp
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
-----BEGIN PGP SIGNATURE-----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=g0AU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
soc/tegra: Changes for v5.14-rc1
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
* tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix Tegra234-only builds
soc/tegra: fuse: Don't return -ENOMEM when allocate lookups failed
soc/tegra: regulators: Support core domain state syncing
soc/tegra: pmc: Add driver state syncing
soc/tegra: pmc: Add core power domain
soc/tegra: fuse: Add stubs needed for compile-testing
soc/tegra: Add devm_tegra_core_dev_init_opp_table()
soc/tegra: Add stub for soc_is_tegra()
soc/tegra: regulators: Bump voltages on system reboot
regulator: core: Add regulator_sync_voltage_rdev()
Link: https://lore.kernel.org/r/20210611164437.3568059-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
In some cases the printf() mechanism is too heavy and can't be used.
For example, when debugging a race condition involving devres API.
When CONFIG_DEBUG_DEVRES is enabled I can't reproduce an issue, and
otherwise it's quite visible with a useful information being collected.
Enable trace events for devres part of the driver core.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517122946.53161-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code for platform_device_create() and of_platform_device_destroy() is
only generated if CONFIG_OF_ADDRESS=y. Add stubs to avoid unresolved
symbols when CONFIG_OF_ADDRESS is not set.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.3.I08fd2e1c775af04f663730e9fb4d00e6bbb38541@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FW is now supporting more than 256 MSI-X per PF (up to 2K).
Hence, enlarge interrupt field in CREATE_EQ to make use of the new
MSI-X's.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The users of EQ are running their code on different CPUs and with
various affinity patterns. Move the cpumask setting close to their
actual usage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the common definition of function_nocfi() is provided by
<linux/mm.h>, and architectures are expected to provide a definition in
<asm/memory.h>. Due to header dependencies, this can make it hard to use
function_nocfi() in low-level headers.
As function_nocfi() has no dependency on any mm code, nor on any memory
definitions, it doesn't need to live in <linux/mm.h> or <asm/memory.h>.
Generally, it would make more sense for it to live in
<linux/compiler.h>, where an architecture can override it in
<asm/compiler.h>.
Move the definitions accordingly.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210602153701.35957-1-mark.rutland@arm.com
This reverts commit 4c38f2df71.
There are few races in the frequency invariance support for CPPC driver,
namely the driver doesn't stop the kthread_work and irq_work on policy
exit during suspend/resume or CPU hotplug.
A proper fix won't be possible for the 5.13-rc, as it requires a lot of
changes. Lets revert the patch instead for now.
Fixes: 4c38f2df71 ("cpufreq: CPPC: Add support for frequency invariance")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'mmc_abort_tuning()' made me think tuning gets completely aborted.
However, it sends only a STOP cmd to cancel the current tuning cmd.
Tuning process may still continue after that. So, rename the function to
'mmc_send_abort_tuning()' to better reflect all this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. As a part of this an optional internal cache
on the SD card, can be used to improve performance.
The let the SD card use the cache, the host needs to enable it and manage
flushing of the cache, so let's add support for this.
Note that for an SD card supporting the cache it's mandatory for it, to
also support the poweroff notification feature. According to the SD spec,
if the cache has been enabled and a poweroff notification is sent to the
card, that implicitly also means that the card should flush its internal
cache. Therefore, dealing with cache flushing for REQ_OP_FLUSH block
requests is sufficient.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210511101359.83521-1-ulf.hansson@linaro.org
Rather than only deselecting the SD card via a CMD7, before we cut power to
it at system suspend, at runtime suspend or at shutdown, let's add support
for a graceful power off sequence via enabling the SD Power Off
Notification feature.
Note that, the Power Off Notification feature was added in the SD spec
v4.x, which is several years ago. However, it's still a bit unclear how
often the SD card vendors decides to implement support for it. To validate
these changes a Sandisk Extreme PRO A2 64GB has been used, which seems to
work nicely.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-12-ulf.hansson@linaro.org
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. These registers let the SD card announce
supports for various performance related features, like "self-maintenance",
"cache" and "command queuing".
Let's extend the parsing of SD function extension registers and store the
information in the struct mmc_card. This prepares for subsequent changes to
implement the complete support for new the performance enhancement
features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-11-ulf.hansson@linaro.org
In the SD spec v4.0 the CMD48/49 and CMD58/59 were introduced as optional
commands. In the SD spec v4.1 the SD function extension registers were
introduced, which requires support for CMD48/49/58/59 to be read/written
from/to.
Moreover, a specific function extension register were added to let the card
announce support for optional features in regards to power management. The
features that were added are "Power Off Notification", "Power Down Mode"
and "Power Sustenance".
As a first step to support this, let's read and parse the register for
power management during the SD card initialization and store the
information about the supported features in the struct mmc_card. In this
way, we prepare for subsequent changes to implement the complete support
for the new features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-10-ulf.hansson@linaro.org
In SD spec v4.x the support for CMD48/49 and CMD58/59 were introduced as
optional features. To let the card announce whether it supports the
commands, the SCR register has been extended with corresponding support
bits. Let's parse and store this information for later use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-9-ulf.hansson@linaro.org
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmDDivETHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoTdHD/9sFhALQjPLLj6g8ioa0VHoF/QlxFS8
XA+Ws4syPVxx+QfbrteJMoh98pASRovKUsKUheOQsvWgetprMSpf0/vg9630+4ap
hRmmiCb8SCFZw8aGYUVObKNUfepPqOM4ArrhcPbiw/aF4vGt7GZB1eXP5++yWLfS
BgY6gC9XVFLvxDHVnB6MqtHzGNlxBcj50f+uZiz5I4/Vk2CkUp9wjS2gZFhRVNao
ZFK0xVObbmBlgeMulE604rkCUkZHfdtXDF7gEApCrv5H2eZ2kNKBjEDxarOyngvb
SRkeVjQwDvc5RJ1dBNIlqcCAScpQr4ryCLK+gPLEHwcqEDaz94ClkyMt+TF9Ox40
QYMEvhz+kTo7LCg8r8rS9T/LoXMRdafxlJDK81Kqg+MaqkEKl5qpy15poc9CkyQX
Rrkrpf45dmYPcz7VVpJ6/6MejiUNAKcIAxuP6n2SlXqyN4ViuJGGI27fLw7hDSFs
X1ithEhc7/9kNCuhyZ6rmi3OKk24GoGX5tSPjyt1M+LiAm2U7GF1AItPDRu//ZgB
5A4bLgQUX6YmS0EyRjNlru1xYn1JwjLIbuwoq4acxcrCVvoRQ+ZIatPOEEU9K7Fc
wfoglwFyE9EnSkmUNBpOu/neFRYj2OzCWT6uKtxeDU/8cx6NGPi0TNOlaxrf3RFF
2jZj8MEJVHSWYw==
=/dXp
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDHMi0ACgkQJNaLcl1U
h9Dbvgf/dAcS9d9lgjijzGYcvsh3hBpWqimMrO/dfXlalqXfdU0VN82++0WIcpC7
uoQ2I6RwU4NNTvMUjbmyQsYONMBNthxYEgGDdtwOE03TLVJHc9KyKCzRLFp0E0sX
wHvoAbSZbzd1OIC+96iWJzeC9rq24LX5IaP8301hWKFhbZpo3/uP9yTgQuxSp0cf
tuQDu8vzW7TuC7pxy06FgCmVhsEd2OXEO+wu9OWzMoIAh2Z82KlEb8j0cpV0G0d1
jPdDanaFwJ3LZevbMXZQnJyCGRhFU74vboSC3Vb8e2H7eCwb68s3Z5mo1Dxq6M3o
qE9JGQRgVVOHr67vYXfirOzmhz2D5g==
=5rP3
-----END PGP SIGNATURE-----
Merge tag 'for-5.14-regulator' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into regulator-5.14
regulator: Changes for v5.14-rc1
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into staging-next
We want the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
