Currently, the probe function initializes the PHY, but PHY settings
are lost during the sleep state. Restore the PHY registers when
resuming.
To facilitate this, split sdhci_cdns_phy_init() into the DT parse
part and PHY update part so that the latter can be invoked from the
resume hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support HS400 Enhanced Strobe feature in Xenon.
Enable Enhanced Strobe together with Data Strobe.
Disable Enhanced Strobe when eMMC is not in HS400 mode.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TI's implementation of sdhci controller used in DRA7 SoC's has
CRC in responses with length 136 bits. Add quirk to indicate
the controller has CRC in MMC_RSP_136. If this quirk is
set sdhci library shouldn't shift the response present in
SDHCI_RESPONSE register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Read each register only once and move the code to a separate function so
that it is not jammed against the 80 column margin.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unused clock rate defines. These should not be defined but
requested from the clock framework.
Also correct typo on the DELAY register
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove CLK_DIVIDER_ALLOW_ZERO. This flag means that a 1 based divider
with a 0 value will behave as a bypass clock
The mmc divider does not behave like this, a 0 value disables the clock
Remove this flag so CCF never allows a 0 value on this clock
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CCF generic mux will shift the mask using the value defined in shift
Define the mask accordingly
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a block device to
mmc_blk_ioctl[_multi]_cmd(), let's pass struct mmc_blk_data()
so we operate ioctl()s on the MMC block device representation
rather than the vanilla block device.
This saves a little duplicated code and makes it possible to
issue ioctl()s not targeted for a specific block device but
rather for a specific partition/area.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a struct mmc_blk_data * to mmc_blk_part_switch()
let's pass the actual partition type we want to switch to. This
is necessary in order not to have a block device with a backing
mmc_blk_data and request queue and all for every hardware partition,
such as RPMB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_ioctl() calls either mmc_blk_ioctl_cmd() or
mmc_blk_ioctl_multi_cmd() and each of these make the same
check. Factor it into a new helper function, call it on
both branches of the switch() statement and save a chunk
of duplicate code.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we don't have the block layer enabled, we do not present card
status and extcsd in the debugfs.
Debugfs is not ABI, and maintaining files of no relevance for
non-block devices comes at a high maintenance cost if we shall
support it with the block layer compiled out.
The debugfs entries suffer from all the same starvation
issues as the other userspace things, under e.g. a heavy
dd operation.
The expected number of debugfs users utilizing these two
debugfs files is already low as there is an ioctl() to get the
same information using the mmc-tools, and of these few users
the expected number of people using it on SDIO or combo cards
are expected to be zero.
It is therefore logical to move this over to the block layer
when it is enabled, using the new custom requests and issue
it using the block request queue.
On the other hand it moves some debugfs code from debugfs.c
and into block.c.
Tested during heavy dd load by cat:in the status file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function retrieves the status of the card with the default
number of retries. Since the block layer wants to use this, and
since the block layer is a loadable kernel module, we need to
export this symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have a data pointer for the ioctl() data, but we need to
pass other data along with the DRV_OP:s, so make this a
void * so it can be reused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Get rid of boilerplate code by using module_platform_driver macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new lockdep annotations for completions cause a warning in the
mmc test module, in a function that now has four 150 byte structures
on the stack:
drivers/mmc/core/mmc_test.c: In function 'mmc_test_nonblock_transfer.constprop':
drivers/mmc/core/mmc_test.c:892:1: error: the frame size of 1360 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The mmc_test_ongoing_transfer function evidently had a similar problem,
and worked around it by using dynamic allocation.
This generalizes the approach used by mmc_test_ongoing_transfer() and
applies it to mmc_test_nonblock_transfer() as well.
Fixes: cd8084f91c ("locking/lockdep: Apply crossrelease to completions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC is not a standard SD host controller. SDHCI_CAPABILITIES_1
register address is 0x44 while it's 0x114 (ESDHC_CAPABILITIES_1)
for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD controller with SDHCI_QUIRK_NO_HISPD_BIT quirk probably
use high speed enable bit for other purpose. So this bit
shouldn't be changed for high speed enabling for this type of
SD controller.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the sdhci-s3c version with
the generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the sdhci-pci version with
the generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the tegra version with the
generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hosts supporting 8-bit bus are marked accordingly. If MMC_CAP_8_BIT_DATA
is not among host capabilities, 8BITBUS bit will never be set and it
is not cleared in case some non-SDHCI3 host uses it for something else.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5) SDHI
is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The branch history code has a loop detection function. With this, we can
get the number of iterations by calculating the removed loops.
While it would be nice for knowing the average cycles of iterations.
This patch adds up the cycles in branch entries of removed loops and
save the result to the next branch entry (e.g. branch entry A).
Finally it will display the iteration number and average cycles at the
"from" of branch entry A.
For example:
perf record -g -j any,save_type ./div
perf report --branch-history --no-children --stdio
--22.63%--main div.c:42 (RET CROSS_2M)
compute_flag div.c:28 (cycles:2 iter:173115 avg_cycles:2)
|
--10.73%--compute_flag div.c:27 (RET CROSS_2M)
rand rand.c:28 (cycles:1)
rand rand.c:28 (RET CROSS_2M)
__random random.c:298 (cycles:1)
__random random.c:297 (COND_BWD CROSS_2M)
__random random.c:295 (cycles:1)
__random random.c:295 (COND_BWD CROSS_2M)
__random random.c:295 (cycles:1)
__random random.c:295 (RET CROSS_2M)
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1502111115-18305-1-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ioctls' struct allows the user to provide a metadata address and
length for a passthrough command. This patch uses these values that were
previously ignored and deletes the now unused wrapper function.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
These functions are used only locally in the nvme core.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Only read and write commands need DIF remapping. Everything else uses
a passthrough integrity payload.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Keep the metadata code in a separate helper instead of making the
main function more complicated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The mutex protects against the list of transports changing while a
controller is being created, but using a plain old mutex means that it
also serializes controller creation. This unnecessarily slows down
creating multiple controllers - for example for the RDMA transport,
creating a controller involves establishing one connection for every IO
queue, which involves even more network/software round trips, so the
delay can become significant.
The simplest way to fix this is to change the mutex to an rwsem and only
hold it for writing when the list is being mutated. Since we can take
the rwsem for reading while creating a controller, we can create multiple
controllers in parallel.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe 1.3 specification defines the Optional Admin Command Support feature
flags, bit 8 set to '1' then the controller supports the Doorbell Buffer
Config command. Bit 7 is used for Virtualization Mangement command.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: f9f38e33 ("nvme: improve performance for virtual NVMe devices")
Cc: stable@vger.kernel.org
The NVMe 1.3 specification says in section 5.21.1.13:
"After a successful completion of a Set Features enabling the host memory
buffer, the host shall not write to the associated host memory region,
buffer size, or descriptor list until the host memory buffer has been
disabled."
While this doesn't state that the descriptor list must remain accessible
to the device it certainly implies it must remaing readable by the device.
So switch to a dma coherent allocation for the descriptor list just to be
safe - it's not like the cost for it matters compared to the actual
memory buffers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 87ad72a59a ("nvme-pci: implement host memory buffer support")
Due to various page sizes in the system (IOMMU/device/kernel), we
set the fabrics controller page size to 4k and block layer boundaries
accordinglly. In architectures that uses different kernel page size
we'll have a mismatch to the MR page size that may cause a mapping error.
Update the MR page size to correspond to the core ctrl settings.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Switch from calling functions exported by the GIC interrupt controller
to using new accessors provided by asm/mips-gic.h. This will allow the
counter-handling functionality to be removed from the interrupt
controller driver, where it doesn't really belong, and also allow for
inlining of the accesses to the GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17021/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduces a new header providing accessor functions for the
MIPS Global Interrupt Controller (GIC) mirroring those provided for the
other 2 components of the MIPS Coherent Processing System (CPS) - the
Coherence Manager (CM) & Cluster Power Controller (CPC).
This header makes use of the new standardised CPS accessor macros where
possible, but does require some custom accessors for cases where we have
either a bit or a register per interrupt.
A major advantage of this over the existing
include/linux/irqchip/mips-gic.h definitions is that code performing
accesses can become much simpler, for example this:
gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) +
GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr),
(unsigned long)trig << GIC_INTR_BIT(intr));
...can become simply:
change_gic_trig(intr, trig);
The accessors handle 32 vs 64 bit in the same way as for CM & CPC code,
which means that GIC code will also not need to worry about the access
size in most cases. They are also accessible outside of
drivers/irqchip/irq-mips-gic.c which will allow for simplification in
the use of the non-interrupt portions of the GIC (eg. counters) which
currently require the interrupt controller driver to expose helper
functions for access.
This patch doesn't change any existing code over to use the new
accessors yet, since a wholesale change would be invasive & difficult to
review. Instead follow-on patches will convert code piecemeal to use
this new header. The one change to existing code is to rename gic_base
to mips_gic_base & make it global, in order to fit in with the naming
expected by the standardised CPS accessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the information needed to issue requests to a CQE is already in
struct mmc_request and struct mmc_data. Add data block address, some flags,
and the task id (tag), and allow for cmd being NULL which it is for CQE
tasks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_return_hold() / mmc_retune_release() are used around a group of
commands to prevent re-tuning between the commands. Re-tuning can still
happen before the first command. In some cases, re-tuning must be
prevented entirely. Add mmc_retune_hold_now() for that purpose. It is
added in preparation for CQE support where it will be used by CQE recovery.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Packed commands support was removed but some bits got left behind. Remove
them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sunxi_mmc_clk_set_phase expects the actual card clock rate to be passed
to it. When the internal divider code was reworked in change ("mmc: sunxi:
Support MMC DDR52 transfer mode with new timing mode"), this requirement
was missed, and the module clock rate was passed in instead. This broke 8
bit DDR MMC on old controllers, as the module clock rate is double the
card clock rate, for which we have no valid delay settings.
Fix this by applying the internal divider to the clock rate right after
we configure it in hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the 64 bit sdbuf width on Renesas R-Car Gen3. If the
registers are 8 byte apart, the width is also 64 bit. For all others,
the width is 32 bit, even if the registers are only 16 bit apart.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't use this new define yet, but it is helpful to document which
versions we know of.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is documented, so enable it to follow the recommendation in the docs
and also save a few cycles.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is one SDHI instance on Gen2 which does not have the CBSY bit.
So, turn CBSY usage into an extra flag and set it accordingly. This has
the additional advantage that we can also set it for other incarnations
later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon specific system-level suspend and resume support.
Especially during resume, re-configure Xenon specific registers
since registers setting will be lost in suspend if Xenon is power off.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.
It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict the code
under the rockchip specified context. So after merging this patch, it
sets up the cto timer for all the platforms using dwmmc IP which isn't
ideal but at least we don't advertise new quirk here. Fortunately, no
obvious performance regression was found by test and the pre-existing
similar catch-all timer for sdhci has proved it's an acceptant way to
make the code as robust as possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
