Since bypassed IOs use no bucket, so do not subtract sectors_to_gc to
trigger gc thread.
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sequential write IOs were tested with bs=1M by FIO in writeback cache
mode, these IOs were expected to be bypassed, but actually they did not.
We debug the code, and find in check_should_bypass():
if (!congested &&
mode == CACHE_MODE_WRITEBACK &&
op_is_write(bio_op(bio)) &&
(bio-＞bi_opf & REQ_SYNC))
goto rescale
that means, If in writeback mode, a write IO with REQ_SYNC flag will not
be bypassed though it is a sequential large IO, It's not a correct thing
to do actually, so this patch remove these codes.
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If blkdev_get_by_path() in register_bcache() fails, we try to lookup the
block device using lookup_bdev() to detect which situation we are in to
properly report error. However we never drop the reference returned to
us from lookup_bdev(). Fix that.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When an RX BA session is started by the driver, and it has to tell
mac80211 about it, the corresponding bit in tid_rx_manage_offl gets
set and the BA session work is scheduled. Upon testing this bit, it
will call __ieee80211_start_rx_ba_session(), thus deadlocking as it
already holds the ampdu_mlme.mtx, which that acquires again.
Fix this by adding ___ieee80211_start_rx_ba_session(), a version of
the function that requires the mutex already held.
Cc: stable@vger.kernel.org
Fixes: 699cb58c8a ("mac80211: manage RX BA session offload without SKB queue")
Reported-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7a7c0a6438 ("mac80211: fix TX aggregation start/stop callback race")
added a cancellation of the ampdu work after the loop that stopped the
Tx and Rx BA sessions. However, in some cases, e.g., during HW reconfig,
the low level driver might call mac80211 APIs to complete the stopping
of the BA sessions, which would queue the ampdu work to handle the actual
completion. This work needs to be performed as otherwise mac80211 data
structures would not be properly synced.
Fix this by checking if BA session STOP_CB bit is set after the BA session
cancellation and properly clean the session.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[Johannes: the work isn't flushed because that could do other things we
don't want, and the locking situation isn't clear]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MIPS is removing this board check so support a cross tree merge.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlmpjMETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NX9B/0SAKFQnfeASg+aZqkPCZjvfSi24LPF
NJ7B4tDdG9/xb09ntLMlILEBXb6psmhZFUXsRojfOUDjeDtWcxzjprFADosX68Js
0HLTnL5rZmycpkS4aZISOu59zhyuLW0EuGgokL8+QagezA0GMSi+h7/F8emO1AUy
iOSCQypgyMSIOKDN6xGyrlwfHdNGeix6sq7t21jw5zi9Oi3iEl/zDdzmH9GaiaNs
Nbm+NqcOrVVoUwxGVM8Gbja8vR/EdWTOv1Rf3OXljv2bACCeAKQ+2sRFq23FMePp
8V0udNxVlXS1r7ZFEq71gHeSQfzgc2h3dQbZa6jEmTw3zsGx+9G89Nkr
=Iq3g
-----END PGP SIGNATURE-----
Merge tag 'spi-falcon-no-board-check' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into 4.14-features
spi: Remove board check from the Falcon driver
MIPS is removing this board check so support a cross tree merge.
Commit 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
added handling of microMIPS instructions to manipulate the stack
pointer. The code that was added violates code style rules with long
lines caused by lots of nested conditionals.
The added code interprets (inline) any known stack pointer manipulation
instruction to find the stack frame size. Handling the microMIPS cases
added quite a bit of complication to this function.
Refactor is_sp_move_ins to perform the interpretation of the immediate
as the instruction manipulating the stack pointer is found. This reduces
the amount of indentation required in get_frame_info, and more closely
matches the operation of is_ra_save_ins.
Suggested-by: Maciej W. Rozycki <macro@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16958/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The stack unwinding code uses the mips_instuction union to decode the
instructions it finds. That union uses the __BITFIELD_FIELD macro to
reorder depending on endianness. The stack unwinding code always places
16bit instructions in halfword 1 of the union. This makes the union
accesses correct for little endian systems. Similarly, 32bit
instructions are reordered such that they are correct for little endian
systems. This handling leaves unwinding the stack on big endian systems
broken, as the mips_instruction union will then look for the fields in
the wrong halfword.
To fix this, use a logical shift to place the 16bit instruction into the
correct position in the word field of the union. Use the same shifting
to order the 2 halfwords of 32bit instuctions. Then replace accesses to
the halfword with accesses to the shifted word.
In the case of the ADDIUS5 instruction, switch to using the
mm16_r5_format union member to avoid the need for a 16bit shift.
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16956/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the immediate encoded in the instruction is accessed, it is sign
extended due to being a signed value being assigned to a signed integer.
The ISA specifies that this operation is an unsigned operation.
The sign extension leads us to incorrectly decode:
801e9c8e: cbf1 sw ra,68(sp)
As having an immediate of 1073741809.
Since the instruction format does not specify signed/unsigned, and this
is currently the only location to use this instuction format, change it
to an unsigned immediate.
Fixes: bb9bc4689b ("MIPS: Calculate microMIPS ra properly when unwinding the stack")
Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Miodrag Dinic <miodrag.dinic@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16957/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
added handling of microMIPS instructions to manipulate the stack
pointer. Unfortunately the decoding of the addiusp instruction was
incorrect, and performed a left shift by 2 bits to the raw immediate,
rather than decoding the immediate and then performing the shift, as
documented in the ISA.
This led to incomplete stack traces, due to incorrect frame sizes being
calculated. For example the instruction:
801faee0 <do_sys_poll>:
801faee0: 4e25 addiu sp,sp,-952
As decoded by objdump, would be interpreted by the existing code as
having manipulated the stack pointer by +1096.
Fix this by changing the order of decoding the immediate and applying
the left shift. Also change to accessing the instuction through the
union to avoid the endianness problem of accesing halfword[0], which
will fail on big endian systems.
Cope with the special behaviour of immediates 0x0, 0x1, 0x1fe and 0x1ff
by XORing with 0x100 again if mod(immediate) < 4. This logic was tested
with the following test code:
int main(int argc, char **argv)
{
unsigned int enc;
int imm;
for (enc = 0; enc < 512; ++enc) {
int tmp = enc << 2;
imm = -(signed short)(tmp | ((tmp & 0x100) ? 0xfe00 : 0));
unsigned short tmp = enc;
tmp = (tmp ^ 0x100) - 0x100;
if ((unsigned short)(tmp + 2) < 4)
tmp ^= 0x100;
imm = -(signed short)(tmp << 2);
printf("%#x\t%d\t->\t(%#x\t%d)\t%#x\t%d\n",
enc, enc,
(short)tmp, (short)tmp,
imm, imm);
}
return EXIT_SUCCESS;
}
Which generates the table:
input encoding -> tmp (matching manual) frame size
-----------------------------------------------------------------------
0 0 -> (0x100 256) 0xfffffc00 -1024
0x1 1 -> (0x101 257) 0xfffffbfc -1028
0x2 2 -> (0x2 2) 0xfffffff8 -8
0x3 3 -> (0x3 3) 0xfffffff4 -12
...
0xfe 254 -> (0xfe 254) 0xfffffc08 -1016
0xff 255 -> (0xff 255) 0xfffffc04 -1020
0x100 256 -> (0xffffff00 -256) 0x400 1024
0x101 257 -> (0xffffff01 -255) 0x3fc 1020
...
0x1fc 508 -> (0xfffffffc -4) 0x10 16
0x1fd 509 -> (0xfffffffd -3) 0xc 12
0x1fe 510 -> (0xfffffefe -258) 0x408 1032
0x1ff 511 -> (0xfffffeff -257) 0x404 1028
Thanks to James Hogan for the test code & verifying the logic.
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Suggested-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16955/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The addiusp instruction uses the pool16d opcode, with bit 0 of the
immediate set. The test for the addiusp opcode erroneously did a logical
and of the immediate with mm_addiusp_func, which has value 1, so this
test always passes when the immediate is non-zero.
Fix the test by replacing the logical and with a bitwise and.
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
added fairly broken support for handling 16bit microMIPS instructions in
get_frame_info(). It adjusts the instruction pointer by 16bits in the
case of a 16bit sp move instruction, but not any other 16bit
instruction.
Commit b6c7a324df ("MIPS: Fix get_frame_info() handling of microMIPS
function size") goes some way to fixing get_frame_info() to iterate over
microMIPS instuctions, but the instruction pointer is still manipulated
using a postincrement, and is of union mips_instruction type. Since the
union is sized to the largest member (a word), but microMIPS
instructions are a mix of halfword and word sizes, the function does not
always iterate correctly, ending up misaligned with the instruction
stream and interpreting it incorrectly.
Since the instruction modifying the stack pointer is usually the first
in the function, that one is usually handled correctly. But the
instruction which saves the return address to the sp is some variable
number of instructions into the frame and is frequently missed due to
not being on a word boundary, leading to incomplete walking of the
stack.
Fix this by incrementing the instruction pointer based on the size of
the previously decoded instruction (& remove the hack introduced by
commit 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
which adjusts the instruction pointer in the case of a 16bit sp move
instruction, but not any other).
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Honor the NL80211_RRF_NO_HT40{MINUS,PLUS} flags in
reg_process_ht_flags_channel. Not doing so leads can lead
to a firmware assert in iwlwifi for example.
Fixes: b0d7aa5959 ("cfg80211: allow wiphy specific regdomain management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: 3f0a06b036 ("MIPS: ralink: adds clkdev code")
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter, as some device
drivers rely on this.
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: f8ede0f700 ("MIPS: Loongson 2F: Add CPU frequency scaling support")
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16777/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.")
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16776/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: 780019ddf0 ("MIPS: AR7: Implement clock API")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reported-by: Mathias Kresin <dev@kresin.me>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16775/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The channels are only 0x40 bytes large, so 0x40 would be the next one's
CHANCFG_REG. Also the position makes it clear that this was intended to
be 0x04. So clearly a typo.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: bcm-kernel-feedback-list@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/15316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On allocating the interrupts routed via a wire-to-MSI bridge, the allocator
iterates over the MSI descriptors to build the hierarchy, but fails to use
the descriptor interrupt number, and instead uses the base number,
generating the wrong IRQ domain mappings.
The fix is to use the MSI descriptor interrupt number when setting up
the interrupt instead of the base interrupt for the allocation range.
The only saving grace is that although the MSI descriptors are allocated
in bulk, the wired interrupts are only allocated one by one (so
desc->irq == virq) and the bug went unnoticed so far.
Fixes: 2145ac9310 ("genirq/msi: Add msi_domain_populate_irqs")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170906103540.373864a2.john@metanate.com
This patch adds ALPS PTP sticks with pid/device id 0x120A to the list of
devices supported by hid-multitouch.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MIPS frame save code was just saving a few registers, enough to
do a backtrace if every function set up a frame. However, this is
not working if you are using DWARF unwinding, because most of the
registers are wrong. This was causing kdump backtraces to be short
or bogus.
So save all the registers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16989/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On the 2nd generation Lenovo Tablet only clickpad is working; the
trackpoint and three mouse buttons do not work.
hid_multitouch must export all inputs in order to get trackpoint and
buttons to function.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Modify the SAVE_SOME macro to look more like a standard
function, doing the arithmetic for the frame on the SP
register instead of copying it from K1, and by saving
the stored EPC from the RA. This lets the get_frame_info()
function process this function like any other. It also
remove an instruction or two from the kernel entry,
making it more efficient.
unwind_stack_by_address() has special handling for
the top of the interrupt stack, but without this change
unwinding will still fail if you get an interrupt while
handling an interrupt and try to do a traceback from
the second interrupt.
This change modifies the get_saved_sp macro to
optionally store the fetched value right into sp and store the
old SP value into K0. Then it's just a matter of subtracting
the frame from SP and storing the old SP from K0.
This required changing the DADDI workaround a bit, since K0
holds the SP, we had to use K1 for AT. But it eliminated
some of the special handling for the DADDI workaround.
Saving the RA register was moved up to before fetching the
CP0_EPC register, so the CP0_EPC register could be stored
into RA and the saved. This lets the traceback code know
where RA is actually stored.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MobileStudio Pro, Cintiq Pro, and 2nd-gen Intuos Pro devices use a
different coordinate system for their touchring and pen twist than prior
devices. Prior devices had zero aligned to the tablet's left and would
increase clockwise. Userspace expects data from the kernel to be in this
old coordinate space, so adjustments are necessary.
While the coordinate system for pen twist is formally defined by the HID
standard, no such definition existed for the touchring at the time these
tablets were introduced. Future tablets are expected to report touchring
data using the same "zero-up clockwise-increasing" coordinate system
defined for twist.
Fixes: 50066a042d ("HID: wacom: generic: Add support for height, tilt, and twist usages")
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org # 4.10, 4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom driver's IRQ handler for Bluetooth reports from the 2nd-gen
Intuos Pro does not correctly process negative numbers. Values for
tilt and rotation (which can go negative) are instead interpreted as
unsigned and so jump to very large values when the data should be
negative. This commit properly casts the data to ensure we report
negative numbers when necessary.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I saw two problems when doing backtraces:
The compiler was putting a "fast return" at the top of some
functions, before it set up the frame. The backtrace code
would stop when it saw a jump instruction, so it would never
get to the stack frame setup and would thus misinterpret it.
To fix this, don't look for jump instructions until the
frame setup has been seen.
The assembly code here is:
ffffffff80b885a0 <serial8250_handle_irq>:
ffffffff80b885a0: c8a00003 bbit0 a1,0x0,ffffffff80b885b0 <serial8250_handle_irq+0x10>
ffffffff80b885a4: 0000102d move v0,zero
ffffffff80b885a8: 03e00008 jr ra
ffffffff80b885ac: 00000000 nop
ffffffff80b885b0: 67bdffd0 daddiu sp,sp,-48
ffffffff80b885b4: ffb00008 sd s0,8(sp)
The second problem was the compiler was putting the last
instruction of the frame save in the delay slot of the
jump instruction. If it saved the RA in there, the
backtrace could would miss it and misinterpret the frame.
To fix this, make sure to process the instruction after
the first jump seen.
The assembly code for this is:
ffffffff80806fd0 <plat_irq_dispatch>:
ffffffff80806fd0: 67bdffd0 daddiu sp,sp,-48
ffffffff80806fd4: ffb30020 sd s3,32(sp)
ffffffff80806fd8: 24130018 li s3,24
ffffffff80806fdc: ffb20018 sd s2,24(sp)
ffffffff80806fe0: 3c12811c lui s2,0x811c
ffffffff80806fe4: ffb10010 sd s1,16(sp)
ffffffff80806fe8: 3c11811c lui s1,0x811c
ffffffff80806fec: ffb00008 sd s0,8(sp)
ffffffff80806ff0: 3c10811c lui s0,0x811c
ffffffff80806ff4: 08201c03 j ffffffff8080700c <plat_irq_dispa
tch+0x3c>
ffffffff80806ff8: ffbf0028 sd ra,40(sp)
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16992/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some laptops have system-control buttons (e.g. KEY_SLEEP) on the same
interface as a hid-multitouch touch-pad.
This commit fixes these buttons not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Ideacom 6680 touchscreen is found in the Dell Latitude 2100. It
has two USB descriptors, the first of which has two input reports. The
HID_QUIRK_MULTI_INPUT quirk is needed to keep the correct maximum
value for ABS_X/ABS_Y (8191 instead of 65535).
Signed-off-by: Nicholas Bishop <nbishop@neverware.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a50aac7193 introduces 'led.groups' and adds EKR support
for these groups. However, unlike the other devices with LEDs,
the EKR's LEDs are read-only and we shouldn't attempt to control
them in wacom_led_control().
See bug: https://sourceforge.net/p/linuxwacom/bugs/342/
Fixes: a50aac7193 ("HID: wacom: leds: dynamically allocate LED groups")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cintiq 12 has 10 expresskey buttons. The bit shift for the last
two buttons were off by 5.
Fixes: c7f0522 ("HID: wacom: Slim down wacom_intuos_pad processing")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Matthieu Robin <matthieu@macolu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The three locks 'lock', 'pgtable_lock' and 'gmap_lock' in the
mm_context_t can be reduced to a single lock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The order in __tlb_flush_mm_lazy is to flush TLB first and then clear
the mm->context.flush_mm bit. This can lead to missed flushes as the
bit can be set anytime, the order needs to be the other way aronud.
But this leads to a different race, __tlb_flush_mm_lazy may be called
on two CPUs concurrently. If mm->context.flush_mm is cleared first then
another CPU can bypass __tlb_flush_mm_lazy although the first CPU has
not done the flush yet. In a virtualized environment the time until the
flush is finally completed can be arbitrarily long.
Add a spinlock to serialize __tlb_flush_mm_lazy and use the function
in finish_arch_post_lock_switch as well.
Cc: <stable@vger.kernel.org>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The local TLB flushing code keeps an additional mask in the mm.context,
the cpu_attach_mask. At the time a global flush of an address space is
done the cpu_attach_mask is copied to the mm_cpumask in order to avoid
future global flushes in case the mm is used by a single CPU only after
the flush.
Trouble is that the reset of the mm_cpumask is racy against the detach
of an mm address space by switch_mm. The current order is first the
global TLB flush and then the copy of the cpu_attach_mask to the
mm_cpumask. The order needs to be the other way around.
Cc: <stable@vger.kernel.org>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KVM has a need to control the interrupts on real and virtualized
AP queue devices. This fix provides a new function to control
the interrupt facilities of an AP queue device.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KVM has a need to fetch the crypto configuration information
as it is returned by the PQAP(QCI) instruction. This patch
introduces a new API ap_query_configuration() which provides
this info in a handy way for the caller.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Under certain specified conditions, the Test AP Queue (TAPQ)
subfunction of the Process Adjunct Processor Queue (PQAP) instruction
will be intercepted by a guest VM. The guest VM must have a means for
executing the intercepted instruction.
The vfio_ap driver will provide an interface to execute the
PQAP(TAPQ) instruction subfunction on behalf of a guest VM.
The code for executing the AP instructions currently resides in the
AP bus. This patch refactors the AP bus code to externalize access
to the PQAP(TAPQ) instruction subfunction to make it available to
the vfio_ap driver.
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In release_stripe_plug(), if a stripe_head has its STRIPE_ON_UNPLUG_LIST
set, it indicates that this stripe_head is already in the raid5_plug_cb
list and release_stripe() would be called instead to drop a reference
count. Otherwise, the STRIPE_ON_UNPLUG_LIST bit would be set for this
stripe_head and it will get queued into the raid5_plug_cb list.
Since break_stripe_batch_list() did not preserve STRIPE_ON_UNPLUG_LIST,
A stripe could be re-added to plug list while it is still on that list
in the following situation. If stripe_head A is added to another
stripe_head B's batch list, in this case A will have its
batch_head != NULL and be added into the plug list. After that,
stripe_head B gets handled and called break_stripe_batch_list() to
reset all the batched stripe_head(including A which is still on
the plug list)'s state and reset their batch_head to NULL.
Before the plug list gets processed, if there is another write request
comes in and get stripe_head A, A will have its batch_head == NULL
(cleared by calling break_stripe_batch_list() on B) and be added to
plug list once again.
Signed-off-by: Dennis Yang <dennisyang@qnap.com>
Cc: stable@vger.kernel.org (v4.1+)
Signed-off-by: Shaohua Li <shli@fb.com>
This patch renames functions regarding to buffer management via META_MAPPING
used for encrypted blocks especially. We can actually use them in generic way.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch replaces (f2fs_encrypted_inode() && S_ISREG()) with
f2fs_encrypted_file(), which gives no functional change.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a test process is not able to write to TH_LOG_STREAM, this step
mechanism enable to print the assert number which triggered the failure.
This can be enabled by setting _metadata->no_print to true at the
beginning of the test sequence.
Update the seccomp-bpf test to return 0 if a test succeeded.
This feature is needed for the Landlock tests.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Link: https://lkml.kernel.org/r/CAGXu5j+D-FP8Kt9unNOqKrQJP4DYTpmgkJxWykZyrYiVPz3Y3Q@mail.gmail.com
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
