Added helper function that checks phy_mode is RGMII (all variants)
'bool phy_interface_mode_is_rgmii(phy_interface_t mode)'
Changed the following function, to use the above.
'bool phy_interface_is_rgmii(struct phy_device *phydev)'
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FCoE to the list of protocols that can set CHECKSUM_UNNECESSARY; add a
note to CHECKSUM_COMPLETE section to specify that it does not apply to SCTP
and FCoE protocols.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_csum_hwoffload_help() uses netdev features and skb->csum_not_inet to
determine if skb needs software computation of Internet Checksum or crc32c
(or nothing, if this computation can be done by the hardware). Use it in
place of skb_checksum_help() in validate_xmit_skb() to avoid corruption
of non-GSO SCTP packets having skb->ip_summed equal to CHECKSUM_PARTIAL.
While at it, remove references to skb_csum_off_chk* functions, since they
are not present anymore in Linux _ see commit cf53b1da73 ("Revert
"net: Add driver helper functions to determine checksum offloadability"").
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->csum_not_inet carries the indication on which algorithm is needed to
compute checksum on skb in the transmit path, when skb->ip_summed is equal
to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been
yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise,
assume Internet Checksum is needed and thus set skb->csum_not_inet to 0.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was introduced with commit 5a21232983 ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_crc32c_csum_help is like skb_checksum_help, but it is designed for
checksumming SCTP packets using crc32c (see RFC3309), provided that
libcrc32c.ko has been loaded before. In case libcrc32c is not loaded,
invoking skb_crc32c_csum_help on a skb results in one the following
printouts:
warn_crc32c_csum_update: attempt to compute crc32c without libcrc32c.ko
warn_crc32c_csum_combine: attempt to compute crc32c without libcrc32c.ko
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_compute_checksum requires crc32c symbol (provided by libcrc32c), so
it can't be used in net core. Like it has been done previously with other
symbols (e.g. ipv6_dst_lookup), introduce a stub struct skb_checksum_ops
to allow computation of crc32c checksum in net core after sctp.ko (and thus
libcrc32c) has been loaded.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a small batch of fixes before -rc1, but here is a larger one. It
contains a backmerge of 4.12-rc1 since some of the downstream branches we
merge had that as base; at the same time we already had merged contents
before -rc1 and rebase wasn't the right solution.
A mix of random smaller fixes and a few things worth pointing out:
- We've started telling people to avoid cross-tree shared branches if all
they're doing is picking up one or two DT-used constants from a
shared include file, and instead to use the numeric values on first
submission. Follow-up moving over to symbolic names are sent in right
after -rc1, i.e. here. It's only a few minor patches of this type.
- Linus Walleij and others are resurrecting the 'Gemini' platform, and
wanted a cut-down platform-specific defconfig for it. So I picked that
up for them.
- Rob Herring ran 'savedefconfig' on arm64, it's a bit churny but it helps
people to prepare patches since it's a pain when defconfig and current
savedefconfig contents differs too much.
- Devicetree additions for some pinctrl drivers for Armada that were
merged this window. I'd have preferred to see those earlier but it's not
a huge deail.
The biggest change worth pointing out though since it's touching other
parts of the tree: We added prefixes to be used when cross-including
DT contents between arm64 and arm, allowing someone to #include
<arm/foo.dtsi> from arm64, and likewise. As part of that, we needed
arm/foo.dtsi to work on arm as well. The way I suggested this to Heiko
resulted in a recursive symlink.
Instead, I've now moved it out of arch/*/boot/dts/include, into a shared
location under scripts/dtc. While I was at it, I consolidated so all
architectures now behave the same way in this manner.
Rob Herring (DT maintainer) has acked it. I cc:d most other arch
maintainers but nobody seems to care much; it doesn't really affect them
since functionality is unchanged for them by default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2EGB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We had a small batch of fixes before -rc1, but here is a larger one.
It contains a backmerge of 4.12-rc1 since some of the downstream
branches we merge had that as base; at the same time we already had
merged contents before -rc1 and rebase wasn't the right solution.
A mix of random smaller fixes and a few things worth pointing out:
- We've started telling people to avoid cross-tree shared branches if
all they're doing is picking up one or two DT-used constants from a
shared include file, and instead to use the numeric values on first
submission. Follow-up moving over to symbolic names are sent in
right after -rc1, i.e. here. It's only a few minor patches of this
type.
- Linus Walleij and others are resurrecting the 'Gemini' platform,
and wanted a cut-down platform-specific defconfig for it. So I
picked that up for them.
- Rob Herring ran 'savedefconfig' on arm64, it's a bit churny but it
helps people to prepare patches since it's a pain when defconfig
and current savedefconfig contents differs too much.
- Devicetree additions for some pinctrl drivers for Armada that were
merged this window. I'd have preferred to see those earlier but
it's not a huge deail.
The biggest change worth pointing out though since it's touching other
parts of the tree: We added prefixes to be used when cross-including
DT contents between arm64 and arm, allowing someone to #include
<arm/foo.dtsi> from arm64, and likewise. As part of that, we needed
arm/foo.dtsi to work on arm as well. The way I suggested this to Heiko
resulted in a recursive symlink.
Instead, I've now moved it out of arch/*/boot/dts/include, into a
shared location under scripts/dtc. While I was at it, I consolidated
so all architectures now behave the same way in this manner.
Rob Herring (DT maintainer) has acked it. I cc:d most other arch
maintainers but nobody seems to care much; it doesn't really affect
them since functionality is unchanged for them by default"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
arm64: dts: rockchip: fix include reference
firmware: ti_sci: fix strncat length check
ARM: remove duplicate 'const' annotations'
arm64: defconfig: enable options needed for QCom DB410c board
arm64: defconfig: sync with savedefconfig
ARM: configs: add a gemini defconfig
devicetree: Move include prefixes from arch to separate directory
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
soc: bcm: brcmstb: Correctly match 7435 SoC
tee: add ARM_SMCCC dependency
ARM: omap2+: make omap4_get_cpu1_ns_pa_addr declaration usable
ARM64: dts: mediatek: configure some fixed mmc parameters
...
This is required for the panel to work on bcm911360, where CLCDCLK is
the fixed 200Mhz AXI41 clock. The rate set is still passed up to the
CLCDCLK, for platforms that have a settable rate on that one.
v2: Set SET_RATE_PARENT (caught by Linus Walleij), depend on
COMMON_CLK.
v3: Mark the clk_ops static (caught by Stephen).
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508193348.30236-1-eric@anholt.net
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
AXP803 PMIC also have a series of regulators (DCDCs and LDOs)
controllable via I2C/RSB bus.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZF2pwAAoJEHm+PkMAQRiG9aAIAJJyV6Ux9kaX+glqO3KIs0wm
0K/yqMOv1JTfJ1UUgY4iZbk5XOPPmXv1bdKJFECZfuAHdymJUF/RVNNvDlZbaLdd
K8vDEi92eRwcf07a5b/Q2F8yNfADKKmRAA/oAbuQLBhJ0dPHig70PIvi9gq9kqiE
Ft1MinbsZLavYatLm7oVDr/nsYebEDMGwTy0EX5bF2YjydfAlCvVWnI5ld5wisiV
0fQF4W7MMjjcpAzG8uq3atEB8iQcWS2Ykz2chZRbYzHcdV2WJW751Vge9xc05Hzi
rxlqn6peZFiFyM0qdPLhY0ktGzSTZcCFeb3aZicvm5aOamy2KJjOSZrEwjU8kts=
=VHpx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
This creates a new section in the security development index for kernel
keys, and adjusts for ReST markup.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
These fixes were needed to parse lsm_hooks.h kernel-doc. More work is
needed, but this is the first step.
Acked-by: James Morris <james.l.morris@oracle.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This updates the credentials API documentation to ReST markup and moves
it under the security subsection of kernel API documentation.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a new interface for registering a serdev controller and clients, and
a helper function to deregister serdev devices (or a tty device) that
were previously registered using the new interface.
Once every driver currently using the tty_port_register_device() helpers
have been vetted and converted to use the new serdev registration
interface (at least for deregistration), we can move serdev registration
to the current helpers and get rid of the serdev-specific functions.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the sram-exec functionality, which allows allocation of
executable memory and provides an API to move code to it, is only
selected in configs for the ARM architecture. Based on commit
5756e9dd0d ("ARM: 6640/1: Thumb-2: Symbol manipulation macros for
function body copying") simply copying a C function pointer address
using memcpy without consideration of alignment and Thumb is unsafe on
ARM platforms.
The aforementioned patch introduces the fncpy macro which is a safe way
to copy executable code on ARM platforms, so let's make use of that here
rather than the unsafe plain memcpy that was previously used by
sram_exec_copy. Now sram_exec_copy will move the code to "dst" and
return an address that is guaranteed to be safely callable.
In the future, architectures hoping to make use of the sram-exec
functionality must define an fncpy macro just as ARM has done to
guarantee or check for safe copying to executable memory before allowing
the arch to select CONFIG_SRAM_EXEC.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vhost-vsock is a software device so there is no probe call that causes
the driver to register its misc char device node. This creates a
chicken and egg problem: userspace applications must open
/dev/vhost-vsock to use the driver but the file doesn't exist until the
kernel module has been loaded.
Use the devname modalias mechanism so that /dev/vhost-vsock is created
at boot. The vhost_vsock kernel module is automatically loaded when the
first application opens /dev/host-vsock.
Note that the "reserved for local use" range in
Documentation/admin-guide/devices.txt is incorrect. The userio driver
already occupies part of that range. I've updated the documentation
accordingly.
Cc: device@lanana.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 6fe729c4bd ("serdev: Add serdev_device_write
subroutine") the function serdev_device_write_buf cannot be used in
atomic context anymore (mutex_lock is sleeping). So restore the old
behavior.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 6fe729c4bd ("serdev: Add serdev_device_write subroutine")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probing of THRE irq behaviour assumes the other end will be reading
bytes out of the buffer in order to probe the port at driver init. In
some cases the other end cannot be relied upon to read these bytes, so
provide a flag for them to skip this step.
Bit 19 was chosen as the flags are a int and the top bits are taken.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch exports skb_array through tap_get_skb_array(). Caller can
then manipulate skb array directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports skb_array through tun_get_skb_array(). Caller can
then manipulate skb array directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduce a batched version of consuming, consumer can
dequeue more than one pointers from the ring at a time. We don't care
about the reorder of reading here so no need for compiler barrier.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications that consume a batch of entries in one go
can benefit from ability to return some of them back
into the ring.
Add an API for that - assuming there's space. If there's no space
naturally can't do this and have to drop entries, but this implies ring
is full so we'd likely drop some anyway.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAPI Changes:
- Return -ENODEV instead of -ENXIO when creating cma fb w/o valid gem (Daniel)
- Add aspect ratio and custom scaling propertis to connector state (Maarten)
Cross-subsystem Changes:
- None
Core Changes:
- Add Laurent as bridge reviewer and Andrzej as bridge maintainer (Archit)
- Maintain new STM driver through -misc (Yannick)
- Misc doc improvements (as is tradition) (Daniel)
- Add driver-private objects to atomic state (Dhinakaran)
- Deprecate preclose hook in modern drivers (use postclose) (Daniel)
- Add hwmode to vblank struct. This fixes mode access in irq context and reduced
a bunch of boilerplate (Daniel)
Driver Changes:
- vc4: Add out-fence support to vc4 V3D rendering (Eric)
- stm: Add stm32f429 display hw and am-480272h3tmqw-t01h panel support (Yannick)
- vc4: Remove 256MB cma limit from vc4 (Eric)
- dw-hdmi: Disable audio when inactive, instead of always enabled (Romain)
- zte: Add support for VGA to the ZTE driver (Shawn)
- i915: Track DP MST bandwidth and check it in atomic_check (Dhinakaran)
- vgem: Enable gem dmabuf import iface to facilitate ion testing (Laura)
- vc4: Add support for Cygnus (new dt compat string + couple bug fixes) (Eric)
- pl111: Add driver for pl111 CLCD display controller (Eric/Tom)
- vgem: Subclass drm_device instead of standalone platform device (Chris)
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tom Cooksey <tom.cooksey@arm.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
* tag 'drm-misc-next-2017-05-16' of git://anongit.freedesktop.org/git/drm-misc: (72 commits)
drm: add missing declaration to drm_blend.h
drm/dp: Wait up all outstanding tx waiters
drm/dp: Read the tx msg state once after checking for an event
drm/prime: Forward declare struct device
drm/vblank: Lock down vblank->hwmode more
drm/vblank: drop the mode argument from drm_calc_vbltimestamp_from_scanoutpos
drm/vblank: Add FIXME comments about moving the vblank ts hooks
drm/vblank: Switch to bool in_vblank_irq in get_vblank_timestamp
drm/vblank: Switch drm_driver->get_vblank_timestamp to return a bool
drm/vgem: Convert to a struct drm_device subclass
gpu: drm: gma500: remove dead code
drm/sti: Adjust two checks for null pointers in sti_hqvdp_probe()
drm/sti: Fix typos in a comment line
drm/sti: Fix a typo in a comment line
drm/sti: Replace 17 seq_puts() calls by seq_putc()
drm/sti: Reduce function calls for sequence output at five places
drm/sti: use seq_puts to display a string
drm: Nerf the preclose callback for modern drivers
drm/exynos: Merge pre/postclose hooks
drm/tegra: switch to postclose
...
Enabling the tracer selftest triggers occasionally the warning in
text_poke(), which warns when the to be modified page is not marked
reserved.
The reason is that the tracer selftest installs kprobes on functions marked
__init for testing. These probes are removed after the tests, but that
removal schedules the delayed kprobes_optimizer work, which will do the
actual text poke. If the work is executed after the init text is freed,
then the warning triggers. The bug can be reproduced reliably when the work
delay is increased.
Flush the optimizer work and wait for the optimizing/unoptimizing lists to
become empty before returning from the kprobes tracer selftest. That
ensures that all operations which were queued due to the probes removal
have completed.
Link: http://lkml.kernel.org/r/20170516094802.76a468bb@gandalf.local.home
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6274de498 ("kprobes: Support delayed unoptimizing")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The kill_css() function may be called more than once under the condition
that the css was killed but not physically removed yet followed by the
removal of the cgroup that is hosting the css. This patch prevents any
harmm from being done when that happens.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v4.5+
TCP Timestamps option is defined in RFC 7323
Traditionally on linux, it has been tied to the internal
'jiffies' variable, because it had been a cheap and good enough
generator.
For TCP flows on the Internet, 1 ms resolution would be much better
than 4ms or 10ms (HZ=250 or HZ=100 respectively)
For TCP flows in the DC, Google has used usec resolution for more
than two years with great success [1]
Receive size autotuning (DRS) is indeed more precise and converges
faster to optimal window size.
This patch converts tp->tcp_mstamp to a plain u64 value storing
a 1 usec TCP clock.
This choice will allow us to upstream the 1 usec TS option as
discussed in IETF 97.
[1] https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver would need to know if there are any active references to a
a PASID before cleaning up its resources. This function helps check
if there are any active users of a PASID before it can perform any
recovery on that device.
To: Joerg Roedel <joro@8bytes.org>
To: linux-kernel@vger.kernel.org
To: David Woodhouse <dwmw2@infradead.org>
Cc: Jean-Phillipe Brucker <jean-philippe.brucker@arm.com>
Cc: iommu@lists.linux-foundation.org
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Usually usb phy need register one extcon device to get the connection
notifications. It will remove some duplicate code if the extcon device
is registered using common code instead of each phy driver having its
own related extcon APIs. So we add one pointer of extcon device into
usb phy structure, and some other helper functions to register extcon.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some situations, e.g. when registering alternate modes for local typec
ports, it may be handy to use constant mode descriptors. Allow this by
changing the mode descriptor arguments of typec_port_register_altmode()
et.al. to using const pointers.
Signed-off-by: Mats Karrman <mats.dev.list@gmail.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some regulators have different settling times for voltage increases and
decreases. To avoid a time penalty on the faster transition allow for
different settings for up- and downward transitions.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OF graph want to count its endpoint number, same as
of_get_child_count(). This patch adds of_graph_get_endpoint_count()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linux kernel already has of_graph_get_remote_port_parent(),
but, sometimes we want to get own port parent.
This patch adds of_graph_get_port_parent()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It should use same method to get same result.
To getting remote-endpoint node,
let's use of_graph_get_remote_endpoint()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 51f5677777 "nfsd: check for oversized NFSv2/v3
arguments", which breaks support for NFSv3 ACLs.
That patch was actually an earlier draft of a fix for the problem that
was eventually fixed by e6838a29ec "nfsd: check for oversized NFSv2/v3
arguments". But somehow I accidentally left this earlier draft in the
branch that was part of my 2.12 pull request.
Reported-by: Eryu Guan <eguan@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
BBR congestion control depends on pacing, and pacing is
currently handled by sch_fq packet scheduler for performance reasons,
and also because implemening pacing with FQ was convenient to truly
avoid bursts.
However there are many cases where this packet scheduler constraint
is not practical.
- Many linux hosts are not focusing on handling thousands of TCP
flows in the most efficient way.
- Some routers use fq_codel or other AQM, but still would like
to use BBR for the few TCP flows they initiate/terminate.
This patch implements an automatic fallback to internal pacing.
Pacing is requested either by BBR or use of SO_MAX_PACING_RATE option.
If sch_fq happens to be in the egress path, pacing is delegated to
the qdisc, otherwise pacing is done by TCP itself.
One advantage of pacing from TCP stack is to get more precise rtt
estimations, and less work done from TX completion, since TCP Small
queue limits are not generally hit. Setups with single TX queue but
many cpus might even benefit from this.
Note that unlike sch_fq, we do not take into account header sizes.
Taking care of these headers would add additional complexity for
no practical differences in behavior.
Some performance numbers using 800 TCP_STREAM flows rate limited to
~48 Mbit per second on 40Gbit NIC.
If MQ+pfifo_fast is used on the NIC :
$ sar -n DEV 1 5 | grep eth
14:48:44 eth0 725743.00 2932134.00 46776.76 4335184.68 0.00 0.00 1.00
14:48:45 eth0 725349.00 2932112.00 46751.86 4335158.90 0.00 0.00 0.00
14:48:46 eth0 725101.00 2931153.00 46735.07 4333748.63 0.00 0.00 0.00
14:48:47 eth0 725099.00 2931161.00 46735.11 4333760.44 0.00 0.00 1.00
14:48:48 eth0 725160.00 2931731.00 46738.88 4334606.07 0.00 0.00 0.00
Average: eth0 725290.40 2931658.20 46747.54 4334491.74 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
4 0 0 259825920 45644 2708324 0 0 21 2 247 98 0 0 100 0 0
4 0 0 259823744 45644 2708356 0 0 0 0 2400825 159843 0 19 81 0 0
0 0 0 259824208 45644 2708072 0 0 0 0 2407351 159929 0 19 81 0 0
1 0 0 259824592 45644 2708128 0 0 0 0 2405183 160386 0 19 80 0 0
1 0 0 259824272 45644 2707868 0 0 0 32 2396361 158037 0 19 81 0 0
Now use MQ+FQ :
lpaa23:~# echo fq >/proc/sys/net/core/default_qdisc
lpaa23:~# tc qdisc replace dev eth0 root mq
$ sar -n DEV 1 5 | grep eth
14:49:57 eth0 678614.00 2727930.00 43739.13 4033279.14 0.00 0.00 0.00
14:49:58 eth0 677620.00 2723971.00 43674.69 4027429.62 0.00 0.00 1.00
14:49:59 eth0 676396.00 2719050.00 43596.83 4020125.02 0.00 0.00 0.00
14:50:00 eth0 675197.00 2714173.00 43518.62 4012938.90 0.00 0.00 1.00
14:50:01 eth0 676388.00 2719063.00 43595.47 4020171.64 0.00 0.00 0.00
Average: eth0 676843.00 2720837.40 43624.95 4022788.86 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 259832240 46008 2710912 0 0 21 2 223 192 0 1 99 0 0
1 0 0 259832896 46008 2710744 0 0 0 0 1702206 198078 0 17 82 0 0
0 0 0 259830272 46008 2710596 0 0 0 0 1696340 197756 1 17 83 0 0
4 0 0 259829168 46024 2710584 0 0 16 0 1688472 197158 1 17 82 0 0
3 0 0 259830224 46024 2710408 0 0 0 0 1692450 197212 0 18 82 0 0
As expected, number of interrupts per second is very different.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
under udp flood the sk_receive_queue spinlock is heavily contended.
This patch try to reduce the contention on such lock adding a
second receive queue to the udp sockets; recvmsg() looks first
in such queue and, only if empty, tries to fetch the data from
sk_receive_queue. The latter is spliced into the newly added
queue every time the receive path has to acquire the
sk_receive_queue lock.
The accounting of forward allocated memory is still protected with
the sk_receive_queue lock, so udp_rmem_release() needs to acquire
both locks when the forward deficit is flushed.
On specific scenarios we can end up acquiring and releasing the
sk_receive_queue lock multiple times; that will be covered by
the next patch
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And update __sk_queue_drop_skb() to work on the specified queue.
This will help the udp protocol to use an additional private
rx queue in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HID sensor hubs using Integrated Senor Hub (ISH) has added capability to
support batch mode. This allows host processor to go to sleep for extended
duration, while the sensor hub is storing samples in its internal buffers.
'Commit f4f4673b75 ("iio: add support for hardware fifo")' implements
feature in IIO core to implement such feature. This feature is used in
bmc150-accel-core.c to implement batch mode. This implementation allows
software device buffer watermark to be used as a hint to adjust hardware
FIFO.
But HID sensor hubs don't allow to change internal buffer size of FIFOs.
Instead an additional usage id to set "maximum report latency" is defined.
This allows host to go to sleep upto this latency period without getting
any report. Since there is no ABI to set this latency, a new attribute
"hwfifo_timeout" is added so that user mode can specify a latency.
This change checks presence of usage id to get/set maximum report latency
and if present, it will expose hwfifo_timeout.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This exports tty_open_by_driver so that it can be called from other
places inside the kernel. The checks for null file pointer are based on
Alan Cox's patch here:
http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1215095.html.
Description below is quoted from it:
"[RFC] tty_port: allow a port to be opened with a tty that has no file handle
Let us create tty objects entirely in kernel space. Untested proposal to
show why all the ideas around rewriting half the uart stack are not needed.
With this a kernel created non file backed tty object could be used to handle
data, and set terminal modes. Not all ldiscs can cope with this as N_TTY in
particular has to work back to the fs/tty layer.
The tty_port code is however otherwise clean of file handles as far as I can
tell as is the low level tty port write path used by the ldisc, the
configuration low level interfaces and most of the ldiscs.
Currently you don't have any exposure to see tty hangups because those are
built around the file layer. However a) it's a fixed port so you probably
don't care about that b) if you do we can add a callback and c) you almost
certainly don't want the userspace tear down/rebuild behaviour anyway.
This should however be sufficient if we wanted for example to enumerate all
the bluetooth bound fixed ports via ACPI and make them directly available.
It doesn't deal with the case of a user opening a port that's also kernel
opened and that would need some locking out (so it returned EBUSY if bound
to a kernel device of some kind). That needs resolving along with how you
"up" or "down" your new bluetooth device, or enumerate it while providing
the existing tty API to avoid regressions (and to debug)."
The exported funtion is used later in this patch set to gain access to tty_struct.
[changed export symbol level - gkh]
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The filesystem documentation was moved from DocBook to
Documentation/filesystems/. Update it at the sources.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
