Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Have the netlink per-protocol optional bind function return an int error code
rather than void to signal a failure.
This will enable netlink protocols to perform extra checks including
capabilities and permissions verifications when updating memberships in
multicast groups.
In netlink_bind() and netlink_setsockopt() the call to the per-protocol bind
function was moved above the multicast group update to prevent any access to
the multicast socket groups before checking with the per-protocol bind
function. This will enable the per-protocol bind function to be used to check
permissions which could be denied before making them available, and to avoid
the messy job of undoing the addition should the per-protocol bind function
fail.
The netfilter subsystem seems to be the only one currently using the
per-protocol bind function.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new ancillary load (bpf call in eBPF parlance) that produces
a 32-bit random number. We are implementing it as an ancillary load
(instead of an ISA opcode) because (a) it is simpler, (b) allows easy
JITing, and (c) seems more in line with generic ISAs that do not have
"get a random number" as a instruction, but as an OS call.
The main use for this ancillary load is to perform random packet sampling.
Signed-off-by: Chema Gonzalez <chema@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethtool patch primarily copies the ioctl command data structures
from/to the User space and invokes the driver hook.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable hibernation for ARM architectures and provide ARM
architecture specific calls used during hibernation.
The swsusp hibernation framework depends on the
platform first having functional suspend/resume.
Then, in order to enable hibernation on a given platform, a
platform_hibernation_ops structure may need to be registered with
the system in order to save/restore any SoC-specific / cpu specific
state needing (re)init over a suspend-to-disk/resume-from-disk cycle.
For example:
- "secure" SoCs that have different sets of control registers
and/or different CR reg access patterns.
- SoCs with L2 caches as the activation sequence there is
SoC-dependent; a full off-on cycle for L2 is not done
by the hibernation support code.
- SoCs requiring steps on wakeup _before_ the "generic" parts
done by cpu_suspend / cpu_resume can work correctly.
- SoCs having persistent state which is maintained during suspend
and resume, but will be lost during the power off cycle after
suspend-to-disk.
This is a rebase/rework of Frank Hofmann's v5 hibernation patchset.
Acked-by: Russ Dill <Russ.Dill@ti.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[fixed duplicate virt_to_pfn() definition --rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bs is no longer used in biovec_create_pool since 9f060e2231 ("block:
Convert integrity to bvec_alloc_bs()")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the 32-bit only setup_sched_clock() API now that all users
have been converted to the 64-bit friendly sched_clock_register().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The caller needs capabilities on the namespace being queried, not on
their own namespace. This is a security bug, although it likely has
only a minor impact.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The edmacc_param struct should follow the layout of the paRAM area in the
HW. Be explicit on the size of the fields (u32) and also mark the struct
as packed to avoid any padding on non 32bit architectures.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-and-Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
-------------------------
Linux does not use the ACC and F bits of the storage key. Newer Linux
versions also do not use the storage keys for dirty and reference
tracking. We can optimize the guest handling for those guests for faults
as well as page-in and page-out by simply not caring about the guest
visible storage key. We trap guest storage key instruction to enable
those keys only on demand.
Migration bitmap
Until now s390 never provided a proper dirty bitmap. Let's provide a
proper migration bitmap for s390. We also change the user dirty tracking
to a fault based mechanism. This makes the host completely independent
from the storage keys. Long term this will allow us to back guest memory
with large pages.
per-VM device attributes
------------------------
To avoid the introduction of new ioctls, let's provide the
attribute semanantic also on the VM-"device".
Userspace controlled CMMA
-------------------------
The CMMA assist is changed from "always on" to "on if requested" via
per-VM device attributes. In addition a callback to reset all usage
states is provided.
Proper guest DAT handling for intercepts
----------------------------------------
While instructions handled by SIE take care of all addressing aspects,
KVM/s390 currently does not care about guest address translation of
intercepts. This worked out fine, because
- the s390 Linux kernel has a 1:1 mapping between kernel virtual<->real
for all pages up to memory size
- intercepts happen only for a small amount of cases
- all of these intercepts happen to be in the kernel text for current
distros
Of course we need to be better for other intercepts, kernel modules etc.
We provide the infrastructure and rework all in-kernel intercepts to work
on logical addresses (paging etc) instead of real ones. The code has
been running internally for several months now, so it is time for going
public.
GDB support
-----------
We provide breakpoints, single stepping and watchpoints.
Fixes/Cleanups
--------------
- Improve program check delivery
- Factor out the handling of transactional memory on program checks
- Use the existing define __LC_PGM_TDB
- Several cleanups in the lowcore structure
- Documentation
NOTES
-----
- All patches touching base s390 are either ACKed or written by the s390
maintainers
- One base KVM patch "KVM: add kvm_is_error_gpa() helper"
- One patch introduces the notion of VM device attributes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jxBp
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140422' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into queue
Lazy storage key handling
-------------------------
Linux does not use the ACC and F bits of the storage key. Newer Linux
versions also do not use the storage keys for dirty and reference
tracking. We can optimize the guest handling for those guests for faults
as well as page-in and page-out by simply not caring about the guest
visible storage key. We trap guest storage key instruction to enable
those keys only on demand.
Migration bitmap
Until now s390 never provided a proper dirty bitmap. Let's provide a
proper migration bitmap for s390. We also change the user dirty tracking
to a fault based mechanism. This makes the host completely independent
from the storage keys. Long term this will allow us to back guest memory
with large pages.
per-VM device attributes
------------------------
To avoid the introduction of new ioctls, let's provide the
attribute semanantic also on the VM-"device".
Userspace controlled CMMA
-------------------------
The CMMA assist is changed from "always on" to "on if requested" via
per-VM device attributes. In addition a callback to reset all usage
states is provided.
Proper guest DAT handling for intercepts
----------------------------------------
While instructions handled by SIE take care of all addressing aspects,
KVM/s390 currently does not care about guest address translation of
intercepts. This worked out fine, because
- the s390 Linux kernel has a 1:1 mapping between kernel virtual<->real
for all pages up to memory size
- intercepts happen only for a small amount of cases
- all of these intercepts happen to be in the kernel text for current
distros
Of course we need to be better for other intercepts, kernel modules etc.
We provide the infrastructure and rework all in-kernel intercepts to work
on logical addresses (paging etc) instead of real ones. The code has
been running internally for several months now, so it is time for going
public.
GDB support
-----------
We provide breakpoints, single stepping and watchpoints.
Fixes/Cleanups
--------------
- Improve program check delivery
- Factor out the handling of transactional memory on program checks
- Use the existing define __LC_PGM_TDB
- Several cleanups in the lowcore structure
- Documentation
NOTES
-----
- All patches touching base s390 are either ACKed or written by the s390
maintainers
- One base KVM patch "KVM: add kvm_is_error_gpa() helper"
- One patch introduces the notion of VM device attributes
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Conflicts:
include/uapi/linux/kvm.h
It's quite common (in the s390 guest access code) to test if a guest
physical address points to a valid guest memory area or not.
So add a simple helper function in common code, since this might be
of interest for other architectures as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fix the following sparse warnings:
drivers/mmc/card/block.c:2421:9: warning: Using plain integer as NULL pointer
drivers/mmc/core/quirks.c:69:9: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch set cleans up the Renesas CMT and TMU drivers in preparation for DT
support.
The first 35 patches are a bunch of necessary cleanups that reorganize the CMT
and TMU drivers, their platform data, and the memory, interrupt and clock
resources they expect. As a result the drivers accept a new platform data
model close to the hardware with supports for all the timer channels using a
single device.
The next 13 patches (36/52 to 48/52) move all CMT and TMU platforms from the
old to the new platform data model. Patches 49/52 to 52/52 then drop support
for the old model and perform one more cleanup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Check EDID Vendor Specific Data Block bytes to see if the connection
is HDMI and set FB_MISC_HDMI.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add driver for STMicroelectronics ST21NFCA NFC controller.
ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as
communication protocol.
Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B.
It is using proprietary gate 15 for ISO14443-3 such as type 1 &
type 2 tags. It is using proprietary gate 14 for type F tags.
ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration.
Standard gate for ISO14443-4 A (13) & B (11) are also used.
ST21NFCA specific mecanism:
One particular point to notice for the data handling is that frame
does not contain any length value. Therefore the i2c part of this driver
is managing the reception with a read length sequence until the end of
frame (0x7e) is reached.
In order to avoid conflict between sof & eof a mecanism
called byte stuffing concist of an escape byte (0x7d) insertion before
special byte (0x7e, 0x7d). The special byte is then xored with 0x20.
In this driver, When data are available in the CLF, the interrupt
gpio is driven to active state and triggered an interrupt.
Once the i2c_master_recv start, the interrupt gpio is driven to idle
state until its complete. If the frame is incomplete or data are still
available, interrupts will be triggered again.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
when checking if our generic PHY is enabled,
it's a lot easier to use IS_ENABLED() instead
of manually checking for it. While at that, also
remove the bogus defined(MODULE) at the end of
the line.
Signed-off-by: Felipe Balbi <balbi@ti.com>
it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of having a list of global functions that are called,
as only one global function is allow to be enabled at a time, there's
no reason to have a list.
Instead, simply have all the users of the global ops, use the global ops
directly, instead of registering their own ftrace_ops. Just switch what
function is used before enabling the function tracer.
This removes a lot of code as well as the complexity involved with it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds the helper __dev_forward_skb which is identical to
dev_forward_skb except that it doesn't actually inject the skb into
the stack. This is useful where we wish to have finer control over
how the packet is injected, e.g., via netif_rx_ni or netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
serio devices exposed via platform firmware interfaces such as ACPI may
provide additional identifying information of use to userspace.
We don't associate the serio devices with the firmware device (we don't
set it as parent), so there's no way for userspace to make use of this
information.
We cannot change the parent for serio devices instantiated though a
firmware interface as that would break suspend / resume ordering.
Therefore this patch adds a new firmware_id sysfs attribute so that
userspace can get a string from there with any additional identifying
information the firmware interface may provide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Here are a few driver fixes for char/misc drivers that resolve reported
issues.
All have been in linux-next successfully for a few days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRlx4ACgkQMUfUDdst+ylYCgCdHm8SDiXwRfhUQJcYYlXrI1xs
skwAn3p1ydnIyVZJ/B3uxTA/0/1Jof5Z
=no/7
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRl6cACgkQMUfUDdst+yllxACfV9fZ/A6IQja60AdPEo+oa6Cw
RiIAoJtH0D0G0eC4+/Qs9GSRMoB4jPPC
=Wi3a
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
Stick in a comment before someone else tries to fix the sparse warning
this generates.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-o2ro6f3vkxklni0bc8f7m68s@git.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree.
- Drop deprecated MSI-X API use.
- A couple other miscellaneous things.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/PTZ
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree
- drop deprecated MSI-X API use.
- a couple other miscellaneous things.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix over-dereference when terminating
RDMA/cxgb4: Use uninitialized_var()
RDMA/cxgb4: Add missing debug stats
RDMA/cxgb4: Initialize reserved fields in a FW work request
RDMA/cxgb4: Use pr_warn_ratelimited
RDMA/cxgb4: Max fastreg depth depends on DSGL support
RDMA/cxgb4: SQ flush fix
RDMA/cxgb4: rmb() after reading valid gen bit
RDMA/cxgb4: Endpoint timeout fixes
RDMA/cxgb4: Use the BAR2/WC path for kernel QPs and T5 devices
IB/mlx5: Add block multicast loopback support
IB/mthca: Use pci_enable_msix_exact() instead of pci_enable_msix()
IB/qib: Use pci_enable_msix_range() instead of pci_enable_msix()
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch factors out the reading of GPIOs for the Arizona devices
into a helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some busses do not support sending/receiving multiple registers in one go.
Such kind of busses just unpack the registers that have been previously
packed by the regmap core or pack registers that will be later unpacked by
the core code.
Add reg_write and reg_read callbacks in order to optimize access through
this kind of busses.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tps65090 regulator allows you to specify how long you want it to
wait before detecting an overcurrent condition. Allow specifying that
through the device tree (or through platform data).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now this driver uses devm_regulator_register() so we don't need to save rdev
pointer to tps->rdev[i] for cleanup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drivers that call regulator_get_optional are tolerant to the absence of
that regulator. By modifying the value returned from the stub function
to match that seen when a regulator isn't present, callers can wrap the
regulator logic with an IS_ERR based conditional even if they happen to
call regulator_is_supported_voltage. This improves efficiency as well
as eliminates the possibility for a very subtle bug.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add an empty version of of_find_node_by_path().
This fixes following build error for asoc tree:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1471:2: error: implicit declaration of function 'of_find_node_by_path' [-Werror=implicit-function-declaration]
sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds support for building PMU driver as module. It exports
the functions perf_pmu_{register,unregister}() and adds reference tracking
for the PMU driver module.
When the PMU driver is built as a module, each active event of the PMU
holds a reference to the driver module.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1395133004-23205-1-git-send-email-zheng.z.yan@intel.com
Cc: eranian@google.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The last user is gone now, so we can safely remove this function.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
