Beginning to introduce those. Just the callers for now, and it's
clumsier than it'll eventually become; once we finish converting
aio_read and aio_write instances, the things will get nicer.
For now, these guys are in parallel to ->aio_read() and ->aio_write();
they take iocb and iov_iter, with everything in iov_iter already
validated. File offset is passed in iocb->ki_pos, iov/nr_segs -
in iov_iter.
Main concerns in that series are stack footprint and ability to
split the damn thing cleanly.
[fix from Peter Ujfalusi <peter.ujfalusi@ti.com> folded]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since we are about to introduce new methods (read_iter/write_iter), the
tests in a bunch of places would have to grow inconveniently. Check
once (at open() time) and store results in ->f_mode as FMODE_CAN_READ
and FMODE_CAN_WRITE resp. It might end up being a temporary measure -
once everything switches from ->aio_{read,write} to ->{read,write}_iter
it might make sense to return to open-coded checks. We'll see...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now It Can Be Done(tm) - we don't need to do iov_shorten() in
generic_file_direct_write() anymore, now that all ->direct_IO()
instances are converted to proper iov_iter methods and honour
iter->count and iter->iov_offset properly.
Get rid of count/ocount arguments of generic_file_direct_write(),
while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
same as iov_iter_get_pages(), except that pages array is allocated
(kmalloc if possible, vmalloc if that fails) and left for caller to
free. Lustre and NFS ->direct_IO() switched to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
counts the pages covered by iov_iter, up to given limit.
do_block_direct_io() and fuse_iter_npages() switched to
it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
iov_iter_get_pages(iter, pages, maxsize, &start) grabs references pinning
the pages of up to maxsize of (contiguous) data from iter. Returns the
amount of memory grabbed or -error. In case of success, the requested
area begins at offset start in pages[0] and runs through pages[1], etc.
Less than requested amount might be returned - either because the contiguous
area in the beginning of iterator is smaller than requested, or because
the kernel failed to pin that many pages.
direct-io.c switched to using iov_iter_get_pages()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For now, just use the same thing we pass to ->direct_IO() - it's all
iovec-based at the moment. Pass it explicitly to iov_iter_init() and
account for kvec vs. iovec in there, by the same kludge NFS ->direct_IO()
uses.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
iov_iter-using variant of generic_file_aio_read(). Some callers
converted. Note that it's still not quite there for use as ->read_iter() -
we depend on having zero iter->iov_offset in O_DIRECT case. Fortunately,
that's true for all converted callers (and for generic_file_aio_read() itself).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
returns the value aligned as badly as the worst remaining segment
in iov_iter is. Use instead of open-coded equivalents.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
all callers of ->aio_read() and ->aio_write() have iov/nr_segs already
checked - generic_segment_checks() done after that is just an odd way
to spell iov_length().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
agp: info leak in agpioc_info_wrap()
fs/affs/super.c: bugfix / double free
fanotify: fix -EOVERFLOW with large files on 64-bit
slub: use sysfs'es release mechanism for kmem_cache
revert "mm: vmscan: do not swap anon pages just because free+file is low"
autofs: fix lockref lookup
mm: filemap: update find_get_pages_tag() to deal with shadow entries
mm/compaction: make isolate_freepages start at pageblock boundary
MAINTAINERS: zswap/zbud: change maintainer email address
mm/page-writeback.c: fix divide by zero in pos_ratio_polynom
hugetlb: ensure hugepage access is denied if hugepages are not supported
slub: fix memcg_propagate_slab_attrs
drivers/rtc/rtc-pcf8523.c: fix month definition
Currently, I am seeing the following when I `mount -t hugetlbfs /none
/dev/hugetlbfs`, and then simply do a `ls /dev/hugetlbfs`. I think it's
related to the fact that hugetlbfs is properly not correctly setting
itself up in this state?:
Unable to handle kernel paging request for data at address 0x00000031
Faulting instruction address: 0xc000000000245710
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2048 NUMA pSeries
....
In KVM guests on Power, in a guest not backed by hugepages, we see the
following:
AnonHugePages: 0 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 64 kB
HPAGE_SHIFT == 0 in this configuration, which indicates that hugepages
are not supported at boot-time, but this is only checked in
hugetlb_init(). Extract the check to a helper function, and use it in a
few relevant places.
This does make hugetlbfs not supported (not registered at all) in this
environment. I believe this is fine, as there are no valid hugepages
and that won't change at runtime.
[akpm@linux-foundation.org: use pr_info(), per Mel]
[akpm@linux-foundation.org: fix build when HPAGE_SHIFT is undefined]
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs fixes from Al Viro:
"dcache fixes + kvfree() (uninlined, exported by mm/util.c) + posix_acl
bugfix from hch"
The dcache fixes are for a subtle LRU list corruption bug reported by
Miklos Szeredi, where people inside IBM saw list corruptions with the
LTP/host01 test.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
nick kvfree() from apparmor
posix_acl: handle NULL ACL in posix_acl_equiv_mode
dcache: don't need rcu in shrink_dentry_list()
more graceful recovery in umount_collect()
don't remove from shrink list in select_collect()
dentry_kill(): don't try to remove from shrink list
expand the call of dentry_lru_del() in dentry_kill()
new helper: dentry_free()
fold try_prune_one_dentry()
fold d_kill() and d_free()
fix races between __d_instantiate() and checks of dentry flags
Replace uses of &__get_cpu_var for address calculation with this_cpu_ptr.
Link: http://lkml.kernel.org/p/alpine.DEB.2.10.1404291415560.18364@gentwo.org
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This set contains a change to the ABI for the hid-sensors drivers to bring them
in line with the long published documentation. Unfortunately, rather than
reporting true scale and offset values via sysfs they were reporting
some magic numbers that could only be converted to anything useful using
the HID sensors specification. I missed this entirely through the introduction
of a number of drivers, only picking up on it recently. Srinivas has had
user feedback about this as well. The patch set is too large to go as a fix
at this stage in the cycle and is not a regression fix as this was never
right and so will have to wait for the next merge window. Srinivas assures
me that there are relatively few pieces of hardware out there and he has
had a number of people contact him to point out that the drivers did not
obey the ABI. Hence hopefully the fallout of this, if any will be minor.
If we don't fix it now, it will only get worse going forward. There is no
sensible way of maintaining the incorrect ABI as it is simply returning
the wrong values through the standard interfaces.
Non IIO elements
* Introduce devm_kmemdup. Does what it says on the tin.
New drivers:
* hid-sensors rotation devices (output as quaternion)
* Freescale MPL115A2 presure and temperature sensor.
* Melexis mlx90614 contactless infrared sensor.
* Freescale MMA8452Q 3-axis accelerometer.
New functionality:
* Addition of multiple element callback to allow for sysfs interfaces to access
elements such as quaternions which have no useful meaning if all 4 elements
are not presented together. Other future usecases for this include
rotation matrices.
* Support for multiple element buffer entries for exactly the same uses as
the sysfs related elements described above.
* Quaternion support via the quaternion IIO modifier.
* TEMP_AMBIENT and TEMP_OBJECT modifiers to distinguish cases with thermopile
devices.
* hid-sensors gain sysfs access to the sensor readings. Previously these
drivers used the buffered interface only. This change involves some
additional hid-sensors core support to read poll values back from the devices
to allow the drivers to know roughly how long to wait for a result when
polling the sensor. There is also an associated hid-sensors abi to allow
the devices to be turned off between reads and powered up on demand.
Cleanups and fixes
* Hid sensors fix as described above. Result is to make the _scale and _offset
attributes applicable in the same way as for all other IIO drivers.
* Some additional documentation - mostly covering stuff that graduated from
staging without managing to take it's ABI docs with it.
* A series of little tidy ups to the exynos_adc driver that make the code
nicer to read and improve handling of some corner cases.
* A tidy up to mag3110 (logical fix rather than a real one ;). Also enable
user offset calibration for this device.
* Drop some left over IS_ERR() checks from ad799x that snuck through during
the cleanup in the last IIO patch set.
* Fix a naming issue from clashing patches in ak8975 - note the clash only
occured in the last IIO patch set, hence the fix needs to go through this
tree.
* A format string missmatch fix in ad7280.c. Unlikely to have ever had an
impact so not worth rushing through.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ghZG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.16b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new drivers, cleanups and functionality for the 3.16 cycle.
This set contains a change to the ABI for the hid-sensors drivers to bring them
in line with the long published documentation. Unfortunately, rather than
reporting true scale and offset values via sysfs they were reporting
some magic numbers that could only be converted to anything useful using
the HID sensors specification. I missed this entirely through the introduction
of a number of drivers, only picking up on it recently. Srinivas has had
user feedback about this as well. The patch set is too large to go as a fix
at this stage in the cycle and is not a regression fix as this was never
right and so will have to wait for the next merge window. Srinivas assures
me that there are relatively few pieces of hardware out there and he has
had a number of people contact him to point out that the drivers did not
obey the ABI. Hence hopefully the fallout of this, if any will be minor.
If we don't fix it now, it will only get worse going forward. There is no
sensible way of maintaining the incorrect ABI as it is simply returning
the wrong values through the standard interfaces.
Non IIO elements
* Introduce devm_kmemdup. Does what it says on the tin.
New drivers:
* hid-sensors rotation devices (output as quaternion)
* Freescale MPL115A2 presure and temperature sensor.
* Melexis mlx90614 contactless infrared sensor.
* Freescale MMA8452Q 3-axis accelerometer.
New functionality:
* Addition of multiple element callback to allow for sysfs interfaces to access
elements such as quaternions which have no useful meaning if all 4 elements
are not presented together. Other future usecases for this include
rotation matrices.
* Support for multiple element buffer entries for exactly the same uses as
the sysfs related elements described above.
* Quaternion support via the quaternion IIO modifier.
* TEMP_AMBIENT and TEMP_OBJECT modifiers to distinguish cases with thermopile
devices.
* hid-sensors gain sysfs access to the sensor readings. Previously these
drivers used the buffered interface only. This change involves some
additional hid-sensors core support to read poll values back from the devices
to allow the drivers to know roughly how long to wait for a result when
polling the sensor. There is also an associated hid-sensors abi to allow
the devices to be turned off between reads and powered up on demand.
Cleanups and fixes
* Hid sensors fix as described above. Result is to make the _scale and _offset
attributes applicable in the same way as for all other IIO drivers.
* Some additional documentation - mostly covering stuff that graduated from
staging without managing to take it's ABI docs with it.
* A series of little tidy ups to the exynos_adc driver that make the code
nicer to read and improve handling of some corner cases.
* A tidy up to mag3110 (logical fix rather than a real one ;). Also enable
user offset calibration for this device.
* Drop some left over IS_ERR() checks from ad799x that snuck through during
the cleanup in the last IIO patch set.
* Fix a naming issue from clashing patches in ak8975 - note the clash only
occured in the last IIO patch set, hence the fix needs to go through this
tree.
* A format string missmatch fix in ad7280.c. Unlikely to have ever had an
impact so not worth rushing through.
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Here are some tty and serial driver fixes for things reported recently.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNn/10ACgkQMUfUDdst+ynKXgCg1BE7sLm2Nmxkm+nfYceWmRG2
pQAAnRnY2wBwtpVa4mVy1ZR3ykiKPvmY
=42O2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for things reported
recently"
* tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix lockless tty buffer race
Revert "tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
drivers/tty/hvc: don't free hvc_console_setup after init
n_tty: Fix n_tty_write crash when echoing in raw mode
tty: serial: 8250_core.c Bug fix for Exar chips.
The of_dma_is_coherent() helper parses the given DT device
node to see if the "dma-coherent" property is supported and
returns true or false accordingly.
If the arch is always coherent or always noncoherent, then the default
DMA ops has to be specified accordingly.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
On few architectures, there are few restrictions on DMAble area of system
RAM. That also means that devices needs to know about this restrictions so
that the dma_masks can be updated accordingly and dma address translation
helpers can add/subtract the dma offset.
In most of cases DMA addresses can be performed using offset value of
Bus address space relatively to physical address space as following:
PFN->DMA: __pfn_to_phys(pfn + [-]dma_pfn_offset)
DMA->PFN: __phys_to_pfn(dma_addr) + [-]dma_pfn_offset
So we introduce per device dma_pfn_offset which can be popullated
by architecture init code while creating the devices.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Create a general __skb_checksum_validate function (actually a
macro) to subsume the various checksum_init functions. This
function can either init the checksum, or do the full validation
(logically checksum_init+skb_check_complete)-- a flag specifies
if full vaidation is performed. Also, there is a flag to the function
to indicate that zero checksums are allowed (to support optional
UDP checksums).
Added several stub functions for calling __skb_checksum_validate.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible a filesystem may send a flush flagged bio with write
data. There is no such composite NVMe command, so the driver sends flush
and write separately.
The device is allowed to execute these commands in any order, so it was
possible the driver ends the bio after the write completes, but while the
flush is still active. We don't want to let a filesystem believe flush
succeeded before it really has; this could cause data corruption on a
power loss between these events. To fix, this patch splits the flush
and write into chained bios.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
This configures an nvme request_queue as flush capable if the device
has a volatile write cache present.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Make the copyright dates accurate and remove the final paragraph that
includes the address of the FSF.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
When starting lots of dataplane devices the bootup takes very long on
Christian's s390 with irqfd patches. With larger setups he is even
able to trigger some timeouts in some components. Turns out that the
KVM_SET_GSI_ROUTING ioctl takes very long (strace claims up to 0.1 sec)
when having multiple CPUs. This is caused by the synchronize_rcu and
the HZ=100 of s390. By changing the code to use a private srcu we can
speed things up. This patch reduces the boot time till mounting root
from 8 to 2 seconds on my s390 guest with 100 disks.
Uses of hlist_for_each_entry_rcu, hlist_add_head_rcu, hlist_del_init_rcu
are fine because they do not have lockdep checks (hlist_for_each_entry_rcu
uses rcu_dereference_raw rather than rcu_dereference, and write-sides
do not do rcu lockdep at all).
Note that we're hardly relying on the "sleepable" part of srcu. We just
want SRCU's faster detection of grace periods.
Testing was done by Andrew Theurer using netperf tests STREAM, MAERTS
and RR. The difference between results "before" and "after" the patch
has mean -0.2% and standard deviation 0.6%. Using a paired t-test on the
data points says that there is a 2.5% probability that the patch is the
cause of the performance difference (rather than a random fluctuation).
(Restricting the t-test to RR, which is the most likely to be affected,
changes the numbers to respectively -0.3% mean, 0.7% stdev, and 8%
probability that the numbers actually say something about the patch.
The probability increases mostly because there are fewer data points).
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> # s390
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added interface to get poll value in milli-seconds. This value is
changed by changing sampling frequency. This API allows clients
to wait for at least some poll milli seconds before reading a new sample.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hub specify a default unit and alternative units. This
along with unit exponent can be used adjust scale. This change
change HID sensor data units to IIO defined units for each
sensor type. So in this way user space can use a simply use:
"(data + offset) * scale" to get final result.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Q_XQUOTARM quotactl was not working properly, because
we weren't passing around proper flags. The xfs_fs_set_xstate()
ioctl handler used the same flags for Q_XQUOTAON/OFF as
well as for Q_XQUOTARM, but Q_XQUOTAON/OFF look for
XFS_UQUOTA_ACCT, XFS_UQUOTA_ENFD, XFS_GQUOTA_ACCT etc,
i.e. quota type + state, while Q_XQUOTARM looks only for
the type of quota, i.e. XFS_DQ_USER, XFS_DQ_GROUP etc.
Unfortunately these flag spaces overlap a bit, so we
got semi-random results for Q_XQUOTARM; i.e. the value
for XFS_DQ_USER == XFS_UQUOTA_ACCT, etc. yeargh.
Add a new quotactl op vector specifically for the QUOTARM
operation, since it operates with a different flag space.
This has been broken more or less forever, AFAICT.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The current code is a bit hard to parse on which registers can be used,
how they are mapped and all play together. It makes much more sense to
define this a bit more clearly so that the code is a bit more intuitive.
This patch cleans this up, and makes naming a bit more consistent among
the code. This also allows for moving some of the defines into the header
file. Clearing of A and X registers in __sk_run_filter() do not get a
particular register name assigned as they have not an 'official' function,
but rather just result from the concrete initial mapping of old BPF
programs. Since for BPF helper functions for BPF_CALL we already use
small letters, so be consistent here as well. No functional changes.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies label naming for the BPF jump-table.
When we define labels via DL(), we just concatenate/textify
the combination of instruction opcode which consists of the
class, subclass, word size, target register and so on. Each
time we leave BPF_ prefix intact, so that e.g. the preprocessor
generates a label BPF_ALU_BPF_ADD_BPF_X for DL(BPF_ALU, BPF_ADD,
BPF_X) whereas a label name of ALU_ADD_X is much more easy
to grasp. Pure cleanup only.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, cgroup->id has been used to identify all the associated
csses and css_from_id() takes cgroup ID and returns the matching css
by looking up the cgroup and then dereferencing the css associated
with it; however, now that the lifetimes of cgroup and css are
separate, this is incorrect and breaks on the unified hierarchy when a
controller is disabled and enabled back again before the previous
instance is released.
This patch adds css->id which is a subsystem-unique ID and converts
css_from_id() to look up by the new css->id instead. memcg is the
only user of css_from_id() and also converted to use css->id instead.
For traditional hierarchies, this shouldn't make any functional
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jianyu Zhan <nasa4836@gmail.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, cgroup->id is allocated from 0, which is always assigned to
the root cgroup; unfortunately, memcg wants to use ID 0 to indicate
invalid IDs and ends up incrementing all IDs by one.
It's reasonable to reserve 0 for special purposes. This patch updates
cgroup core so that ID 0 is not used and the root cgroups get ID 1.
The ID incrementing is removed form memcg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Li Zefan <lizefan@huawei.com>
There's no reason to use atomic bitops for cgroup_subsys_state->flags,
cgroup_root->flags and various subsys_masks. This patch updates those
to use bitwise and/or operations instead and converts them form
unsigned long to unsigned int.
This makes the fields occupy (marginally) smaller space and makes it
clear that they don't require atomicity.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
The base code imported from the Google tree is ifdef heaven. Prepare to fix
this by adding a helper function.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the mapping of the relID to channel is done under the protection of a
single spin lock. Starting with ws2012, each channel is bound to a specific VCPU
in the guest. Use this binding to eliminate the spin lock by setting up
per-cpu state for mapping relId to the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By ensuring that we set the callback handler to NULL in the channel close
path on the same CPU that the channel is bound to, we can eliminate this lock
acquisition and release in a performance critical path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
