Add missing support for matching on IPv6 flow label for STEv0.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There are usecases with Connection Tracking that have such connection
as default, printing this warning in dmesg confuses the user.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In the event of SW steering QP entering error state, SW steering
cannot insert more rules, and will silently ignore the insertion
after issuing a warning.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Enable pop VLAN action in TX and push VLAN in RX.
These actions are supported only on STEv1.
On TX: when a host sends a packet, VLAN is popped at the beginning.
On RX: just before passing the packet to the host the VLAN is pushed.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Split modify vlan state in the actions state machine to pop vlan
and push vlan states. This enables using of pop/push vlan without
restrictions (e.g. pop vlan on TX in STEv1).
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
ConnectX supports offloading of various encapsulations and decapsulations
(e.g. VXLAN), which are performed by 'Packet Reformat' action. Starting
with ConnectX-6 DX, a new reformat type is supported - REMOVE_HEADER, which
allows deleting an arbitrary size chunk at the selected position in the packet.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
In line 849 (#1), "mlx5dr_htbl_put(cur_htbl);" drops the reference to
cur_htbl and may cause cur_htbl to be freed.
However, cur_htbl is subsequently used in the next line, which may result
in an use-after-free bug.
Fix this by calling mlx5dr_err() before the cur_htbl is put.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If link aggregation is used within stack devices driver rejects encap
rules if PF of the VF tunnel device is down. This happens because route
resolved for other PF and its eswitch instance is used to determine
correct vport.
To fix that use devcom feature to retrieve other eswitch instance if
failed to find vport for the 1st eswitch and LAG is active.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When indirect forward group is created, flow is added with vhca id but
without setting vhca id valid flag which violates the PRM.
Fix by setting the missing flag, vhca id valid.
Fixes: 34ca65352d ("net/mlx5: E-Switch, Indirect table infrastructure")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
After neigh-update-add failure we are still with a slow path rule but
the driver always assume the rule is an fdb rule.
Fix neigh-update-del by checking slow path tc flag on the flow.
Also fix neigh-update-add for when neigh-update-del fails the same.
Fixes: 5dbe906ff1 ("net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The call to mlx5_unregister_device() means that mlx5_core driver is
removed. In such scenario, we need to disregard all other flags like
attach/detach and forcibly remove all auxiliary devices.
Fixes: a5ae8fc905 ("net/mlx5e: Don't create devices during unload flow")
Tested-and-Reported-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When handling FIB_EVENT_ENTRY_REPLACE event for a new multipath route,
lag activation can be missed if a stale (struct lag_mp)->mfi pointer
exists, which was associated with an older multipath route that had been
removed.
Normally, when a route is removed, it triggers mlx5_lag_fib_event(),
which handles FIB_EVENT_ENTRY_DEL and clears mfi pointer. But, if
mlx5_lag_check_prereq() condition isn't met, for example when eswitch is
in legacy mode, the fib event is skipped and mfi pointer becomes stale.
Fix by resetting mfi pointer to NULL in mlx5_deactivate_lag().
Fixes: 8a66e45859 ("net/mlx5: Change ownership model for lag")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is a spelling mistake in an error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
... not PGD
vmalloc() sets up the kernel page table (starting from @swapper_pg_dir).
But when vmalloc area is accessed in context of a user task, say opening
terminal in n_tty_open(), the user page tables need to be synced from
kernel page tables so that TLB entry is created in "user context".
The old code was doing this incorrectly, as it was updating the user pgd
entry (first level itself) to point to kernel pud table (2nd level),
effectively yanking away the entire user space translation with kernel one.
The correct way to do this is to ONLY update a user space pgd/pud/pmd entry
if it is not popluated already. This ensures that only the missing leaf
pmd entry gets updated to point to relevant kernel pte table.
From code change pov, we are chaging the pattern:
p4d = p4d_offset(pgd, address);
p4d_k = p4d_offset(pgd_k, address);
if (!p4d_present(*p4d_k))
goto bad_area;
set_p4d(p4d, *p4d_k);
with
p4d = p4d_offset(pgd, address);
p4d_k = p4d_offset(pgd_k, address);
if (p4d_none(*p4d_k))
goto bad_area;
if (!p4d_present(*p4d))
set_p4d(p4d, *p4d_k);
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
ARCv2 MMU is software walked and Linux implements 2 levels of paging: pgd/pte.
Forthcoming hw will have multiple levels, so this change preps mm code
for same. It is also fun to try multi levels even on soft-walked code to
ensure generic mm code is robust to handle.
overview
________
2 levels {pgd, pte} : pmd is folded but pmd_* macros are valid and operate on pgd
3 levels {pgd, pmd, pte}:
- pud is folded and pud_* macros point to pgd
- pmd_* macros operate on actual pmd
code changes
____________
1. #include <asm-generic/pgtable-nopud.h>
2. Define CONFIG_PGTABLE_LEVELS 3
3a. Define PMD_SHIFT, PMD_SIZE, PMD_MASK, pmd_t
3b. Define pmd_val() which actually deals with pmd
(pmd_offset(), pmd_index() are provided by generic code)
3c. pmd_alloc_one()/pmd_free() also provided by generic code
(pmd_populate/pmd_free already exist)
4. Define pud_none(), pud_bad() macros based on generic pud_val() which
internally pertains to pgd now.
4b. define pud_populate() to just setup pgd
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
With previous patch ARC pgalloc functions are same as generic, hence
switch to that.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
So far ARC pgtable_t has not been struct page based to avoid extra
page_address() calls involved. However the differences are down to
noise and get in the way of using generic code, hence this patch.
This also allows us to reuse generic THP depost/withdraw code.
There's some additional consideration for PGDIR_SHIFT in 4K page config.
Now due to page tables being PAGE_SIZE deep only, the address split
can't be really arbitrary.
Tested-by: kernel test robot <lkp@intel.com>
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
To check beacon protection had a mismatch of the key ID we
currently use the key ID from the firmware, but firmware
side we want to clean up the API to stop reporting this.
Instead, check the IWL_RX_MPDU_STATUS_KEY_VALID bit that
indicates that the firmware used the correct key, and if
that's set but we get invalid MIC/replay use the key ID
from the frame to look up the key and notify mac80211 of
MIC error or replay. Since both keys must have the same
cipher and thus MIC length, we can use either of them to
look up the MIC length.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.30e665d39b07.I78bf7d304ef5a80cecf5fa1c1fca0b51b956cceb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Enable/disable setting the session id in the FTM frame
2. Set the BSS color for the responder
3. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.0a10d43f3d7f.Ice4112c1910cf94babd1c2d492a3a3de9f7ee6cb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This version adds the following configuration options:
1. Set the BSS color for NDP ranging
2. Set the minimum and maximum time between measurements for
non trigger based NDP ranging.
3. Terminate the session in case the responder requests LMR feedback.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210826224715.9dcd5210b7e5.I76f6977cde852de0f251344e279ad85076eef8d6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can send this even if initializing in RF-kill, thus
suppressing a bunch of error messages about it. In fact,
we _want_ to, since we might still want to debug the
firmware even if in RF-kill.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.bcdb076609e2.I2d177c00772510b5338d8aa45af7558138b08448@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When P2P roc is removed, the IWL_MVM_STATUS_NEED_FLUSH_P2P bit is set
to indicate to iwl_mvm_roc_done_wk() that the removed roc is a P2P
one, so it will flush the broadcast station and not the aux station.
However, since setting this bit and scheduling the worker is done
in roc ended flow as well as in case the roc is removed, there is
a race where the worker has already started running (but did not
test this bit yet) and then it is scheduled again. In this case,
the first run of the worker will clear this bit, and thus the second
run will find it already cleared and will try to flush and remove
the aux station by mistake.
Fix it by scheduling the worker only if this bit is not yet set. In
case this bit is already set, the worker is either running or
scheduled, so there is no need to re-schedule it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.8c147659b331.If5924375e9bfd46214ab8ab81cb9d0f5c82fbcbc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug dump ranges aren't just an array of such ranges
since each range has a variable size. Therefore, the use
of a struct array is misleading at best.
Change it to be a u8 data[] instead of the struct array,
the code doesn't significantly change since it's actually
doing things correctly now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.693c9891097d.Idcaab1fd659e8be2f56be647b2534befd61a4460@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't use this, but we embed this struct elsewhere and
having structs with flexible arrays embedded isn't quite
right, with sparse (for example) complaining. Remove the
data[] member in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.72ca1232b27c.I6ec766691b89670e1683f9fc0fbd12648309a574@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
DMA-API debug code pointed out that in this code path we
never check the return value of dma_map_page(), which could
fail.
However, we don't really even want to unmap/remap, we just
want to ensure that we can actually access the last version
of the data that the (now-dead) device may have written, so
only need to dma_sync_single_for_cpu() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.5987f35883a2.I2d9ea5ecc69a5e5947b546fb15f33363a0595651@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to load the regdomain only in the load stage,
this caused the 'iw phy phy0 reg get' command to fail if we
booted a machine with wifi off.
Therefor we should load it in INIT stage already.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.a6077801d7d5.I7d8d5c895bc467efbf81ea055dde366ea01cced1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We used to read the PPAG, WRDS, EWRD, WGDS tables from ACPI
in the load stage only. This prevented vendor commands from
being executed before bringing the interface up. Move reading those tables
to INIT stage.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.ce3b60f0b426.I3643bf00e714aae930880cc7d6cf390b142eaccb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit 79f033f6f2 ("iwlwifi: dbg: don't limit dump decisions
to all or monitor") we changed the code to pass around a bitmap,
but in the monitor_only case, one place accidentally used the bit
number, not the bit mask, resulting in CSR and FW_INFO getting
dumped instead of monitor data. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.774fd8729a33.Ic985a787071d1c0b127ef0ba8367da896ee11f57@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By mistake we were considering the first element of the WTAS wifi
package as part of the data we want to rid, but that element is the wifi
package signature (always 0x07), so it should be skipped.
Change the code to read the data starting from element 1 instead.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Fixes: 28dd7ccdc5 ("iwlwifi: acpi: read TAS table from ACPI and send it to the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.ff8148197b15.I70636c04e37b2b57a5df3ce611511f62203d27a7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command has same size and layout as
version 10. It just sends corresponding station id in one
of the reserved fields. It's not used in the driver, so just
be ready to accept version 11.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.0a387598eef1.I3be0bbf603ef95c644218be8a12b329411f11646@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GEO profiles have been stored in single-dimension arrays and the
access has been done via a single index. We will soon need to support
different revisions of this table, which will make the flat array even
harder to handle. To prepare for that, convert the single-dimension
array to a struct with substructures.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.56f3506411a2.I600ed3708d19f2263a5a8d143f6711d08499bbb0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change the SAR profile tables storage to revision 2 regardless of the
revision we read from ACPI. Revision 2 is a superset of revision 1,
which is in turn a superset of revision 0, so they can all be stored
inside revision 2.
Add support for reading and storing also revisions 1 and 2, whose only
difference is the number of chains and number of sub-bands. So most
of the code revolves around passing different chain and sub-band
sizes.
With this patch we still pass only revision 0 to the firmware, but
that will be changed in a separate patch.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.2edad09415c8.I36297aef90a9ec6a3ea1bf1a151a62f272826d59@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
