htab can't use generic batch support due some problematic behaviours
inherent to the data structre, i.e. while iterating the bpf map a
concurrent program might delete the next entry that batch was about to
use, in that case there's no easy solution to retrieve the next entry,
the issue has been discussed multiple times (see [1] and [2]).
The only way hmap can be traversed without the problem previously
exposed is by making sure that the map is traversing entire buckets.
This commit implements those strict requirements for hmap, the
implementation follows the same interaction that generic support with
some exceptions:
- If keys/values buffer are not big enough to traverse a bucket,
ENOSPC will be returned.
- out_batch contains the value of the next bucket in the iteration, not
the next key, but this is transparent for the user since the user
should never use out_batch for other than bpf batch syscalls.
This commits implements BPF_MAP_LOOKUP_BATCH and adds support for new
command BPF_MAP_LOOKUP_AND_DELETE_BATCH. Note that for update/delete
batch ops it is possible to use the generic implementations.
[1] https://lore.kernel.org/bpf/20190724165803.87470-1-brianvv@google.com/
[2] https://lore.kernel.org/bpf/20190906225434.3635421-1-yhs@fb.com/
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115184308.162644-6-brianvv@google.com
This adds the generic batch ops functionality to bpf arraymap, note that
since deletion is not a valid operation for arraymap, only batch and
lookup are added.
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200115184308.162644-5-brianvv@google.com
This commit adds generic support for update and delete batch ops that
can be used for almost all the bpf maps. These commands share the same
UAPI attr that lookup and lookup_and_delete batch ops use and the
syscall commands are:
BPF_MAP_UPDATE_BATCH
BPF_MAP_DELETE_BATCH
The main difference between update/delete and lookup batch ops is that
for update/delete keys/values must be specified for userspace and
because of that, neither in_batch nor out_batch are used.
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115184308.162644-4-brianvv@google.com
This commit introduces generic support for the bpf_map_lookup_batch.
This implementation can be used by almost all the bpf maps since its core
implementation is relying on the existing map_get_next_key and
map_lookup_elem. The bpf syscall subcommand introduced is:
BPF_MAP_LOOKUP_BATCH
The UAPI attribute is:
struct { /* struct used by BPF_MAP_*_BATCH commands */
__aligned_u64 in_batch; /* start batch,
* NULL to start from beginning
*/
__aligned_u64 out_batch; /* output: next start batch */
__aligned_u64 keys;
__aligned_u64 values;
__u32 count; /* input/output:
* input: # of key/value
* elements
* output: # of filled elements
*/
__u32 map_fd;
__u64 elem_flags;
__u64 flags;
} batch;
in_batch/out_batch are opaque values use to communicate between
user/kernel space, in_batch/out_batch must be of key_size length.
To start iterating from the beginning in_batch must be null,
count is the # of key/value elements to retrieve. Note that the 'keys'
buffer must be a buffer of key_size * count size and the 'values' buffer
must be value_size * count, where value_size must be aligned to 8 bytes
by userspace if it's dealing with percpu maps. 'count' will contain the
number of keys/values successfully retrieved. Note that 'count' is an
input/output variable and it can contain a lower value after a call.
If there's no more entries to retrieve, ENOENT will be returned. If error
is ENOENT, count might be > 0 in case it copied some values but there were
no more entries to retrieve.
Note that if the return code is an error and not -EFAULT,
count indicates the number of elements successfully processed.
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115184308.162644-3-brianvv@google.com
This commit moves reusable code from map_lookup_elem and map_update_elem
to avoid code duplication in kernel/bpf/syscall.c.
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200115184308.162644-2-brianvv@google.com
- Fix DAT candidate selection on little endian systems,
by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=6zKP
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200114' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- Fix DAT candidate selection on little endian systems,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In f2fs_rename(), new_page is gone after f2fs_set_link(), but it tries
to put again when whiteout is failed and jumped to put_out_dir.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
META_MAPPING is used to move blocks for both encrypted and verity files.
So the META_MAPPING invalidation condition in do_checkpoint() should
consider verity too, not just encrypt.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In low memory scenario, we can allocate multiple bios without
submitting any of them.
- f2fs_write_checkpoint()
- block_operations()
- f2fs_sync_node_pages()
step 1) flush cold nodes, allocate new bio from mempool
- bio_alloc()
- mempool_alloc()
step 2) flush hot nodes, allocate a bio from mempool
- bio_alloc()
- mempool_alloc()
step 3) flush warm nodes, be stuck in below call path
- bio_alloc()
- mempool_alloc()
- loop to wait mempool element release, as we only
reserved memory for two bio allocation, however above
allocated two bios may never be submitted.
So we need avoid using default bioset, in this patch we introduce a
private bioset, in where we enlarg mempool element count to total
number of log header, so that we can make sure we have enough
backuped memory pool in scenario of allocating/holding multiple
bios.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Remove duplicate sbi->aw_cnt stats counter that tracks
the number of atomic files currently opened (it also shows
incorrect value sometimes). Use more relit lable sbi->atomic_files
to show in the stats.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
To catch f2fs bugs in write pointer handling code for zoned block
devices, check write pointers of non-open zones that current segments do
not point to. Do this check at mount time, after the fsync data recovery
and current segments' write pointer consistency fix. Or when fsync data
recovery is disabled by mount option, do the check when there is no fsync
data.
Check two items comparing write pointers with valid block maps in SIT.
The first item is check for zones with no valid blocks. When there is no
valid blocks in a zone, the write pointer should be at the start of the
zone. If not, next write operation to the zone will cause unaligned write
error. If write pointer is not at the zone start, reset the write pointer
to place at the zone start.
The second item is check between the write pointer position and the last
valid block in the zone. It is unexpected that the last valid block
position is beyond the write pointer. In such a case, report as a bug.
Fix is not required for such zone, because the zone is not selected for
next write operation until the zone get discarded.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
On sudden f2fs shutdown, write pointers of zoned block devices can go
further but f2fs meta data keeps current segments at positions before the
write operations. After remounting the f2fs, this inconsistency causes
write operations not at write pointers and "Unaligned write command"
error is reported.
To avoid the error, compare current segments with write pointers of open
zones the current segments point to, during mount operation. If the write
pointer position is not aligned with the current segment position, assign
a new zone to the current segment. Also check the newly assigned zone has
write pointer at zone start. If not, reset write pointer of the zone.
Perform the consistency check during fsync recovery. Not to lose the
fsync data, do the check after fsync data gets restored and before
checkpoint commit which flushes data at current segment positions. Not to
cause conflict with kworker's dirfy data/node flush, do the fix within
SBI_POR_DOING protection.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (85) call bpf_get_socket_cookie#46
1: R0_w=invP(id=0) R10=fp0
1: (57) r0 &= 808464432
2: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
2: (14) w0 -= 810299440
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
3: (c4) w0 s>>= 1
4: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
4: (76) if w0 s>= 0x30303030 goto pc+216
221: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
221: (95) exit
processed 6 insns (limit 1000000) [...]
Taking a closer look, the program was xlated as follows:
# ./bpftool p d x i 12
0: (85) call bpf_get_socket_cookie#7800896
1: (bf) r6 = r0
2: (57) r6 &= 808464432
3: (14) w6 -= 810299440
4: (c4) w6 s>>= 1
5: (76) if w6 s>= 0x30303030 goto pc+216
6: (05) goto pc-1
7: (05) goto pc-1
8: (05) goto pc-1
[...]
220: (05) goto pc-1
221: (05) goto pc-1
222: (95) exit
Meaning, the visible effect is very similar to f54c7898ed ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.
The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:
dst_reg->smin_value >>= umin_val;
dst_reg->smax_value >>= umin_val;
dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);
Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:
[...]
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP65535 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (57) r0 &= 808464432
-> R0_runtime = 0x3030
3: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
3: (14) w0 -= 810299440
-> R0_runtime = 0xcfb40000
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
(0xffffffff)
4: (c4) w0 s>>= 1
-> R0_runtime = 0xe7da0000
5: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0x7ffbfff8)
[...]
In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.
Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r2 = 808464432
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP808464432 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (bf) r6 = r0
3: R0_w=invP(id=0) R6_w=invP(id=0) R10=fp0
3: (57) r6 &= 808464432
4: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
4: (14) w6 -= 810299440
5: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
5: (c4) w6 s>>= 1
6: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0xfffbfff8)
6: (76) if w6 s>= 0x30303030 goto pc+216
7: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
7: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 8 insns (limit 1000000) [...]
Fixes: 9cbe1f5a32 ("bpf/verifier: improve register value range tracking with ARSH")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115204733.16648-1-daniel@iogearbox.net
kmemleak detects the following memory leak when hot removing
a network device:
unreferenced object 0xffff888083f63600 (size 256):
comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
hex dump (first 32 bytes):
00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00 .@.3............
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
backtrace:
[<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
[<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
[<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
[<00000000046e64f1>] really_probe+0x22f/0xb50
[<000000005cc35eb7>] driver_probe_device+0x25e/0x370
[<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
[<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
[<00000000a72c362f>] bus_probe_device+0x1a6/0x260
[<0000000008478399>] device_add+0x10a3/0x18e0
[<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
[<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
[<000000002c94bb64>] process_one_work+0x919/0x17d0
[<0000000096de6781>] worker_thread+0x87/0xb40
[<00000000fbe7397e>] kthread+0x333/0x3f0
[<000000004f844269>] ret_from_fork+0x3a/0x50
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the retry of btsoc initialization when it fails. There are
reports that the btsoc initialization may fail on some platforms but the
repro ratio is very low. The symptoms is the firmware downloading failed
due to the UART write timed out. The failure may be caused by UART,
platform HW or the btsoc itself but it's very difficlut to root cause,
given the repro ratio is very low. Add a retry for the btsoc initialization
can work around most of the failures and make Bluetooth finally works.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Current qca_power_shutdown() only supports wcn399x, this patch adds Rome
power off support to it. For Rome it just needs to pull down the bt_en
GPIO to power off it. This patch also replaces all the power off operation
in qca_close() with the unified qca_power_shutdown() call.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.
To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().
Packetdrill to demonstrate:
// Disable RACK and set max_reordering to keep things simple
0 `sysctl -q net.ipv4.tcp_recovery=0`
+0 `sysctl -q net.ipv4.tcp_max_reordering=3`
// Establish a connection
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <...>
+.01 < . 1:1(0) ack 1 win 257
+0 accept(3, ..., ...) = 4
// Send 8 data segments
+0 write(4, ..., 8000) = 8000
+0 > P. 1:8001(8000) ack 1
// Enter recovery and 1:3001 is marked lost
+.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>
// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
+0 > . 1:1001(1000) ack 1
// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
+.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost
// BUG: 2001:3001 was not retransmitted
+0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for getting IRQ directly from DT instead of relying on
converting a GPIO to IRQ. This is needed for platforms with GPIO
controllers that that do not support gpiod_to_irq().
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add interrupts and interrupt-names as optional properties
to support host-wakeup by interrupt properties instead of
host-wakeup-gpios.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check for valid packet type before calling hci_recv_frame which is
inline with what other drivers are doing.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables H5 driver to properly handle ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables H4 driver to properly handle ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reuse __check_timeout on hci_sched_le following the same logic
used hci_sched_acl.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables passing ISO packets to the monitor socket.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This make virtual controllers to pass ISO packets around.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These adds the HCI definitions for handling CIS connections along with
ISO data packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MGMT command is added to receive the list of blocked keys from
user-space.
The list is used to:
1) Block keys from being distributed by the device during
the ke distribution phase of SMP.
2) Filter out any keys that were previously saved so
they are no longer used.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a test that will attach a FENTRY and FEXIT program to the XDP test
program. It will also verify data from the XDP context on FENTRY and
verifies the return code on exit.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/157909410480.47481.11202505690938004673.stgit@xdp-tutorial
Investigation on the AXP803 shows that VBUS_PLUGIN/VBUS_REMOVAL IRQs are
triggered on the rising/falling edge of AXP20X_PWR_STATUS_VBUS_USED. The
reason IRQs do not arrive while N_VBUSEN/DRIVEVBUS is high is because
AXP20X_PWR_STATUS_VBUS_USED also never goes high.
This also means that if VBUS is online, a VBUS_REMOVAL IRQ is received
immediately on setting N_VBUSEN/DRIVEVBUS high (and VBUS_PLUGIN shortly
after it is set back low). This was also verified to be the case when
manually offlining VBUS through AXP20X_VBUS_PATH_SELECT.
As long as VBUS is online, a present->absent transition necessarily
implies an online->offline transition. Since will cause an IRQ, there is
no need to poll while VBUS is online.
To ensure the driver's view of VBUS online status remains accurate,
unconditionally poll once when receiving an IRQ and when resuming. If
VBUS is still online at that time, polling will cease until the next
VBUS_REMOVAL IRQ.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The USB power supply input can be used as a wakeup source. Hook up the
VBUS_PLUGIN IRQ to trigger wakeup based on userspace configuration.
To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.
Because we now depend on the specific order of the IRQs (we assume
VBUS_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.
To avoid spuriously waking up the system when the USB power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.
The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
snd_seq_info_timer_read() reads the information of the timer assigned
for each queue, but it's done in a racy way which may lead to UAF as
spotted by syzkaller.
This patch applies the missing q->timer_mutex lock while accessing the
timer object as well as a slight code change to adapt the standard
coding style.
Reported-by: syzbot+2b2ef983f973e5c40943@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200115203733.26530-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AXP803/AXP813 have a flag that enables/disables the USB power supply
input. Allow control of this flag via the ONLINE property on those
variants.
It may be necessary to offline the USB power supply input when using
the USB port in OTG mode, or to allow userspace to disable charging.
When the USB VBUS input is disabled via the PATH_SEL bit, the VBUS_USED
bit in PWR_INPUT_STATUS is cleared, so there is no change needed when
getting the property.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some SRP targets that do not support specification SRP-2, put the garbage
to the reserved bits of the SRP login response. The problem was not
detected for a long time because the SRP initiator ignored those bits. But
now one of them is used as SRP_LOGIN_RSP_IMMED_SUPP. And it causes a
critical error on the target when the initiator sends immediate data.
The ib_srp module has a use_imm_date parameter to enable or disable
immediate data manually. But it does not help in the above case, because
use_imm_date is ignored at handling the SRP login response. The problem is
definitely caused by a bug on the target side, but the initiator's
behavior also does not look correct. The initiator should not use
immediate data if use_imm_date is disabled by a user.
This commit adds an additional checking of use_imm_date at the handling of
SRP login response to avoid unexpected use of immediate data.
Fixes: 882981f4a4 ("RDMA/srp: Add support for immediate data")
Link: https://lore.kernel.org/r/20200115133055.30232-1-sergeygo@mellanox.com
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The SGE buffer size and max_inline data should be derived from the size of
the WQE. Each value individually sets the WQE size, so compute the actual
sizes based on the actual WQE size and configure the QP with the maximums.
Also fix the missing return of the actual maximum capability to the caller.
Link: https://lore.kernel.org/r/1578962480-17814-3-git-send-email-rao.shoaib@oracle.com
Signed-off-by: Rao Shoaib <rao.shoaib@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of ad-hoc variant ID checks throughout the code, let's start
moving the variant-specific details to a match structure. This allows
for future flexibility, and it better matches the other axp20x power
supply drivers.
This commit removes most variant checks from axp20x_usb_power_probe().
Other parts of the driver still do ID matching; they are left unchanged
for now.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/ucs1002_power.c:492:5: warning: symbol 'ucs1002_regulator_enable' was not declared. Should it be static?
Fixes: a3d70dacc7 ("power: suppy: ucs1002: disable power when max current is 0")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Suspend to IDLE invokes tick_unfreeze() on resume. tick_unfreeze() on the
first resuming CPU resumes timekeeping, which also has the side effect of
resetting the softlockup watchdog on this CPU.
But on the secondary CPUs the watchdog is not reset in the resume /
unfreeze() path, which can result in false softlockup warnings on those
CPUs depending on the time spent in suspend.
Prevent this by clearing the softlock watchdog in the unfreeze path also
on the secondary resuming CPUs.
[ tglx: Massaged changelog ]
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200110083902.27276-1-chunyan.zhang@unisoc.com
The recommendation is that the set_active should be done
with pm runtime disabled.
Also fix the remove path for clocking.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's not always the case that clock is already available when i2c
driver get probed at the first time, e.g. the clock is provided by
clock wizard which may be probed after i2c driver. So let's defer
the probe when devm_clk_get() call fails and give it chance to
try later.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add timeout to the rx fifo empty wait loop. Also check for the return
value for xiic_reinit and pass it to xiic_start_xfer.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
size_t should be printed with its own format to be 64-bit friendly and
fix warning when compiling on 64-bit platform (e.g. with COMPILE_TEST):
drivers/i2c/busses/i2c-highlander.c: In function ‘highlander_i2c_smbus_xfer’:
drivers/i2c/busses/i2c-highlander.c:325:22: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pnx.c: In function ‘i2c_pnx_probe’:
drivers/i2c/busses/i2c-pnx.c:737:47: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 5 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pmcmsp.c: In function ‘pmcmsptwi_probe’:
drivers/i2c/busses/i2c-pmcmsp.c:276:25: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 3 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The LLVM patch https://reviews.llvm.org/D72197 makes LLVM emit function call
relocations within the same section. This includes a default .text section,
which contains any BPF sub-programs. This wasn't the case before and so libbpf
was able to get a way with slightly simpler handling of subprogram call
relocations.
This patch adds support for .text section relocations. It needs to ensure
correct order of relocations, so does two passes:
- first, relocate .text instructions, if there are any relocations in it;
- then process all the other programs and copy over patched .text instructions
for all sub-program calls.
v1->v2:
- break early once .text program is processed.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115190856.2391325-1-andriin@fb.com
Intel Software Developer's Manual, volume 3, chapter 9.11.6 says:
"Note that the microcode update must be aligned on a 16-byte boundary
and the size of the microcode update must be 1-KByte granular"
When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image. Image that was created something like this:
iucode_tool --write-earlyfw=FOO.cpio microcode-files...
However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.
Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.
[ If we end up having other firmware with much bigger alignment
requirements, we might need to introduce some method for the firmware
to specify it, this is the minimal "just increase the alignment a bit
to account for this one special case" patch - Linus ]
Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
