head is traversed using hlist_for_each_entry_rcu outside an RCU
read-side critical section but under the protection of dtab->index_lock.
Hence, add corresponding lockdep expression to silence false-positive
lockdep warnings, and harden RCU lists.
Fixes: 6f9d451ab1 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200123120437.26506-1-frextrite@gmail.com
Existing clock divider functions is not checking for
base of divider. So, if any clock divider is power of 2
then clock rate calculation will be wrong.
Add support to calculate divider value for the clocks
with CLK_DIVIDER_POWER_OF_TWO flag.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-7-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
zynqmp_clk_divider_round_rate() returns actual divider value
after calculating from parent rate and desired rate, even though
that rate is not supported by single divider of hardware. It is
also possible that such divisor value can be achieved through 2
different dividers. As, Linux tries to set such divisor value(out
of range) in single divider set divider is getting failed.
Fix the same by computing best possible combination of two
divisors which provides more accurate clock rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-6-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To achieve best possible rate, maximum limit of divider is required
while computation. Get maximum supported divisor from firmware. To
maintain backward compatibility assign maximum possible value(0xFFFF)
if query for max divisor is not successful.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-5-git-send-email-rajan.vaja@xilinx.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
[sboyd@kernel.org: Remove else return and just return]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Warn user if clock is used by more than allowed devices.
This check is done by firmware and returns respective
error code. Upon receiving error code for excessive user,
warn user for the same.
This change is done to restrict VPLL use count. It is
assumed that VPLL is used by one user only.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-4-git-send-email-rajan.vaja@xilinx.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Versal compatible string to support Versal
binding.
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-3-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Convert the gpio-leds binding to DT schema format.
Drop the last example as the node name collides when built, and it doesn't
add much value.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the common LEDs properties bindings to a schema. As trigger source
providers are different nodes, we need to split trigger source properties
to a separate file.
Bindings for LED controllers can reference the common schema for the LED
child nodes:
patternProperties:
"^led@[0-4]":
type: object
allOf:
- $ref: common.yaml#
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: linux-leds@vger.kernel.org
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Show thermal and SVI registers for Family 17h CPUs.
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The maximum Tdie or Tctl is not published for Ryzen CPUs. What is
known, however, is that the traditional value of 70 degrees C is no
longer correct. On top of that, the limit applies to Tctl, not to Tdie.
Displaying it in either context is meaningless, confusing, and wrong.
Stop doing it.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ryzen CPUs report core and SoC voltages and currents. Add support
for it to the k10temp driver.
For the time being, only report voltages and currents for Ryzen
CPUs. Threadripper and EPYC appear to use a different mechanism.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Zen2 reports reporting temperatures per CPU die (called Core Complex Dies,
or CCD, by AMD). Add support for it to the k10temp driver.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert driver to use devm_hwmon_device_register_with_info to simplify
the code and to reduce its size.
Old size (x86_64):
text data bss dec hex filename
8247 4488 64 12799 31ff drivers/hwmon/k10temp.o
New size:
text data bss dec hex filename
6778 2792 64 9634 25a2 drivers/hwmon/k10temp.o
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using bitops makes bit masks and shifts easier to read.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver stops the fan in suspend but leaves the fan on in
shutdown. It seems strange to leave the fan on in shutdown because there
is no use case in my mind and the gpio-fan driver on the other hand stops
in shutdown.
This change turns off the fan in shutdown. If anyone complains then we'll
add an optional property to switch the behavior.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kamil Debski <kamil@wypas.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/1579534344-11694-1-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for devices XDPE12254, XDPE12284.
All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-5-vadimp@mellanox.com
[groeck: Added missing break statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend "vrm_version" with the type for Intel IMVP9 and AMD 6.25mV VID
modes.
Add calculation for those types.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-3-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-2-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1578411640-16929-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/hwmon/w83627ehf.c: In function 'w83627ehf_check_fan_inputs':
drivers/hwmon/w83627ehf.c:1296:24: warning:
variable 'fan4min' set but not used [-Wunused-but-set-variable]
commit 62000264cfa8 ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200108034514.50130-1-yuehaibing@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1: +23.0°C
or directly from sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +23.0°C, highest = +34.0°C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for a number of manufacturer-specific registers in the
debugfs entries, as well as support to read and write the
PMBUS_ON_OFF_CONFIG register through debugfs.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-2-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now the nct677* are gone, we can clean up some flags that are
always the same now and simplify some code.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nct6775 and nct6776 are supported by the separate nct6775.c driver,
so remove the code from the w83627ehf driver.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-2-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix sparse warning:
drivers/hwmon/w83627ehf.c:1202:1: warning:
symbol 'sensor_dev_attr_pwm1_target' was not declared. Should it be static?
and many more similar messages.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Link: https://lore.kernel.org/r/20191213015605.172472-1-chenzhou10@huawei.com
[groeck: Dropped all but one log message from description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a chip is write protected, we can not change any limits, and we can
not clear status flags. This may be the reason why clearing status flags
is reported to not work for some chips. Detect the condition in the pmbus
core. If the chip is write protected, set limit attributes as read-only,
and set the flag indicating that the status flag should be ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon ABI supports enable attributes since commit fb41a710f8
("hwmon: Document the sensor enable attribute"), but did not
add support for those attributes to the hwmon core. Do that now.
Since the enable attributes are logically the most important attributes,
they are added as first attribute to the attribute list. Move
hwmon_in_enable from last to first place for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the old hwmon_device_register code to
devm_hwmon_device_register_with_info.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191124202030.45360-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the generic PCI host binding to DT schema. The derivative Juno,
PLDA XpressRICH3-AXI, and Designware ECAM bindings all just vary in
their compatible strings. The simplest way to convert those to
schema is just add them into the common generic PCI host schema.
The HiSilicon ECAM and Cavium ThunderX PEM bindings have an additional
'reg' entry, but are otherwise the same binding as well.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Will Deacon <will@kernel.org>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the Arm Versatile PCI host binding to a DT schema.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
syzbot reported an out-of-bound access in em_nbyte. As initially
analyzed by Eric, this is because em_nbyte sets its own em->datalen
in em_nbyte_change() other than the one specified by user, but this
value gets overwritten later by its caller tcf_em_validate().
We should leave em->datalen untouched to respect their choices.
I audit all the in-tree ematch users, all of those implement
->change() set em->datalen, so we can just avoid setting it twice
in this case.
Reported-and-tested-by: syzbot+5af9a90dad568aa9f611@syzkaller.appspotmail.com
Reported-by: syzbot+2f07903a5b05e7f36410@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the reader of the document is aware that some active
installation of the libyaml development package is required and
provide two examples.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 DFSDM bindings to DT schema format
using json-schema.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
