Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Modify dma controller nodes name to fit with the standard naming.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
phy-names is required by usbotg_hs driver to get the phy, otherwise, it
considers that there is no phys property.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB OTG HS on stm32mp15 dkx in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp15 dk boards.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USBPHYC (USB PHY Controller on stm32mp15 DKx boards.
This enables the two usbphyc usb2 ports, which require 3 supplies:
3v3, 1v1 and 1v8.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Commit 179e5a6114 ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.
Fixes: f702e0b93c ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Memory address/size depends on board design, so memory node should
be in board DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Memory address/size depends on board design, so memory node should
be in board DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7D is supported for either the v7-A or the v7-M cores,
but the latter causes a warning:
WARNING: unmet direct dependencies detected for ARM_ERRATA_814220
Depends on [n]: CPU_V7 [=n]
Selected by [y]:
- SOC_IMX7D [=y] && ARCH_MXC [=y] && (ARCH_MULTI_V7 [=n] || ARM_SINGLE_ARMV7M [=y])
Make the select statement conditional.
Fixes: 4562fa4c86 ("ARM: imx: Enable ARM_ERRATA_814220 for i.MX6UL and i.MX7D")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 micro-SD port.
Pass the "broken-cd" property to describe the absence of the card detect
GPIO so that polling must be used.
According to Documentation/devicetree/bindings/mmc/mmc-controller.yaml:
broken-cd:
$ref: /schemas/types.yaml#/definitions/flag
description:
There is no card detection available; polling must be used.
Even though no error is oberved in the kernel, the lack of the
'broken-cd' property caused the micro-SD to not be detected in U-Boot,
so let's improve the device tree description to make it more accurate.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf6 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 3feea8805d ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead1 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 93385546ba ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is nothing to synchronize in regards to memory stores, thus all
readl/writel occurrences in the code could be replaced with a relaxed
versions, for consistency.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-9-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "spinlock.h", which was included indirectly, and sort includes in
alphabet order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-8-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes few dozens of legit checkpatch warnings, adds missed
handling of potential error-cases and prettifies code where makes sense.
All these clean-up changes are quite minor and do not fix any real
problems.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-7-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHY provides init/shutdown callbacks which allow USB-host drivers
to abstract PHY's hardware management in a common way. This change allows
to remove Tegra-specific PHY handling from the ChipIdea driver.
Note that ChipIdea's driver shall be changed at the same time because it
turns PHY ON without the PHY's initialization and this doesn't work now,
resulting in a NULL dereference of phy->freq because it's set during of
the PHY's initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY driver should keep track of the enable state, otherwise enable
refcount is screwed if USB driver tries to enable PHY when it is already
enabled. This will be the case for ChipIdea and Tegra EHCI drivers once
PHY driver will gain support for the init/shutdown callbacks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, the PHY's clock needs to unprepared to keep prepare count
balanced. Secondly, downstream code suggests that reset is synchronous
and thus it should be asserted before disabling clock.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-4-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found that PHY's enable refcounting was broken and after fixing it
I also found that machine started to hang after EHCI driver module
removal. Turned out that the teardown order is incorrect because HCD must
be unregistered *before* PHY's disabling. Note that it is also not correct
to assert the shared reset during of driver's removal because PHY takes
care of resetting shared pads and thus it's better to remove that part
from the EHCI driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA Tegra SoCs use ChipIdea silicon IP for the USB controllers.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `connected` value for wired devices was not properly initialized,
it must be set to `true` upon creation, because wired devices do not
generate connection events.
When a raw client (the Steam Client) uses the device, the input device
is destroyed. Then, when the raw client finishes, it must be recreated.
But since the `connected` variable was false this never happended.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-9-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMEM framework is an interface for the at24 EEPROMs as well as for
other drivers, instead of passing the wp-gpios over the different
drivers each time, it would be better to pass it over the NVMEM
subsystem once and for all.
Removing the support for the write-protect pin after adding it to the
NVMEM subsystem.
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Defining the USB modes from the latest USB Power Delivery
Specification - USB 2.0, USB 3.2 and USB4 - as special modal
states just like the Accessory Modes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-14-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing all the details that the alternate mode drivers
provide to the mux drivers during mode changes.
The mux drivers will in practice need to be able to make
decisions on their own. It is not enough that they get only
the requested port state. With the Thunderbolt 3 alternate
mode for example the mux driver will need to consider also
the capabilities of the cable before configuring the mux.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-13-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discover Identity command response has also 3 product type
specific VDOs on top of ID Header VDO, Cert Stat VDO and
Product VDO.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-11-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMEM framework is an interface for the at24 EEPROMs as well as for
other drivers, instead of passing the wp-gpios over the different
drivers each time, it would be better to pass it over the NVMEM
subsystem once and for all.
Making wp-gpios a reference to the property defined by nvmem.
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The latest version of the USB Power Delivery Specification
R3.0 added UFP and DFP product types for the Discover
Identity message. Both types can be used for example for
checking the USB capability of the partner, which means the
USB modes (USB 2.0, USB 3.0 and USB4) that the partner
device supports.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-10-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 2.0 of the USB Power Delivery Specification R3.0
defines a new message called Enter_USB, which is made with
USB4 in mind. Enter_USB message is in practice the same as
the Enter Mode command (used when entering alternate modes)
that just needs to be used when entering USB4 mode.
The message does also support entering USB 2.0 or USB 3.2
mode instead of USB4 mode, but it is only required with
USB4. I.e. with USB2 and USB3 Enter_USB message is optional.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-9-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write-protect pin handling looks like a standard property that
could benefit other users if available in the core nvmem framework.
Instead of modifying all the memory drivers to check this pin, make
the NVMEM subsystem check if the write-protect GPIO being passed
through the nvmem_config or defined in the device tree and pull it
low whenever writing to the memory.
There was a suggestion for introducing the gpiodesc from pdata, but
as pdata is already removed it could be replaced by adding it to
nvmem_config.
Reference: https://lists.96boards.org/pipermail/dev/2018-August/001056.html
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Thunderbolt 3, and probable USB4 too, will need to be able
to get details about the cables. Adding typec_cable_get()
function that the alternate mode drivers can use to gain
access to gain access to the cable.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the port drivers were expected to check does the
connector have the mode enabled or disabled when the alt
mode drivers attempted to enter the mode, but since
typec_altmode_enter() puts the connector into USB Safe
State before calling the port driver, it really has to do
the check on its own, and before changing the state.
Otherwise the connector may be left in USB Safe State if the
port driver does not move it back to normal USB operation
when the mode is disabled.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several memories have a write-protect pin, that when pulled high, it
blocks the write operation.
On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing.
Instead of modifying all the memory drivers to check this pin, make
the NVMEM subsystem check if the write-protect GPIO being passed
through the nvmem_config or defined in the device tree and pull it
low whenever writing to the memory.
Add a new optional property to the device tree binding document, which
allows to specify the GPIO line to which the write-protect pin is
connected.
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This patch switches to platform_get_irq_optional() from
platform_get_irq() as it causes a false-positive error such as 'IRQ
index 0 not found' when IRQ is not used. The IRQ usage is optional in
this gpio-altera driver, so the error log is undesirable.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We should not be reaching into property entries and initialize them by
hand, but rather use proper initializer macros. This way we can alter
internal representation of property entries with no visible changes to
their users.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IMX DSP is only needed by SOF or any other module that
wants to communicate with the DSP. When SOF is build
as a module IMX DSP is forced to be built inside the
kernel image. This is not optimal, so allow IMX DSP
to be built as a module.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
