Russell King says:
====================
sfp: Allow slow to initialise GPON modules to work
Some GPON modules take longer than the SFF MSA specified time to
initialise and respond to transactions on the I2C bus for either
both 0x50 and 0x51, or 0x51 bus addresses. Technically these modules
are non-compliant with the SFP Multi-Source Agreement, they have
been around for some time, so are difficult to just ignore.
Most of the patch series is restructuring the code to make it more
readable, and split various things into separate functions.
We split the three state machines into three separate functions, and
re-arrange them to start probing the module as soon as a module has
been detected (without waiting for the network device.) We try to
read the module's EEPROM, retrying quickly for the first second, and
then once every five seconds for about a minute until we have read
the EEPROM. So that the kernel isn't entirely silent, we print a
message indicating that we're waiting for the module to respond after
the first second, or when all retries have expired.
Once the module ID has been read, we kick off a delayed work queue
which attempts to register the hwmon, retrying for up to a minute if
the monitoring parameters are unreadable; this allows us to proceed
with module initialisation independently of the hwmon state.
With high-power modules, we wait for the netdev to be attached before
switching the module power mode, and retry this in a similar way to
before until we have successfully read and written the EEPROM at 0x51.
We also move the handling of the TX_DISABLE signal entirely to the main
state machine, and avoid probing any on-board PHY while TX_FAULT is
set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is inserted, we attempt to read read the ID from address
0x50. Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51. If this
fails, then we fall into error state, and assume that the module is
not usable.
Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately. However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted. This prompts us to fall into the error state.
Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.
Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)
Only report module removal if we had previously reported a module
insertion.
This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the power mode switching from the probe, so that we don't
repeatedly re-probe the SFP device if there is a problem accessing
the registers at I2C address 0x51.
In splitting this out, we can also fix a bug where we leave the module
in high-power mode when the upstream device is detached but the module
is still inserted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the upstream's attachment state in the state machine rather than
maintaining a boolean, which ensures that we have a strict order of
ATTACH followed by an UP event - we can never believe that a newly
attached upstream will be anything but down.
Rearrange the order of state machines so we run the module state
machine after the upstream device's state machine, so the module state
machine can check the current state of the device and take action to
e.g. reset back to empty state when the upstream is detached.
This is to allow the module detection to run independently of the
network device becoming available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_FAULT should be deasserted to indicate that the module has completed
its initialisation. This may include the on-board PHY, so wait until
the module has deasserted TX_FAULT before probing the PHY.
This means that we need an extra state to handle a TX_FAULT that
remains set for longer than t_init, since using the existing handling
state would bypass the PHY probe.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the next state to sfp_sm_fault() so that it can branch to other
states. This will be necessary to improve the initialisation path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using mdelay() to wait before probing the PHY (which holds
several locks, including the rtnl lock), add an extra wait state to
the state machine to introduce the 50ms delay without holding any
locks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY probe into a separate function, splitting it from
sfp_sm_mod_init(). This will allow us to eliminate the 50ms mdelay()
inside the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialise TX_DISABLE when the sfp cage is probed, and then
maintain its state in the main state machine. However, the module
state machine:
- negates it when detecting a newly inserted module when it's already
guaranteed to be negated.
- negates it when the module is removed, but the main state machine
will do this anyway.
Make TX_DISABLE entirely controlled by the main state machine.
The main state machine also probes the module for a PHY, and removes
the PHY when the the module is removed. Hence, removing the PHY in
sfp_sm_module_remove() is also redundant, and is a left-over from
when we tried to probe for the PHY from the module state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the module indicates that it requires an address change sequence to
switch between address 0x50 and 0x51, which we don't support, we can't
write to the register that controls the power mode to switch to high
power mode. Warn the user that the module may not be functional in
this case, and don't try to change the power mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse the SFP power requirement earlier, in preparation for moving the
power level setup code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8472 rev 12.2 defines the time for the serial bus to become ready
using t_serial. Use this as our identifier for this timeout to make
it clear what we are referring to.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing a module resets the module state machine back to its initial
state. Rather than explicitly handling this in every state, handle it
early on outside of the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp_sm_ins_next() modifies the module state machine. Change it's name
to reflect this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the tx disable assertion on device down to the main state
machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the SFP sub-state machines out of the main state machine function,
in preparation for it doing a bit more with the device state. By doing
so, we ensure that our debug after the main state machine is always
printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Infinite timeout loops are hard to read. Refactor it to plausible 'do {}
while ()'.
Note, the supplied timeout can't be negative for current use, though if
it's not dividable to 10, we may go below 0, that's why type of the
parameter is int. And thus, we may move the check to the loop condition.
No functional change intended.
Link: https://lore.kernel.org/r/20191108111855.85866-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The kbuild test robot found a problem with htmldocs with the recent
change to the SFP interfaces. Fix the kernel documentation for
sfp_bus_put() which was missing an '@' before the argument name
description.
Fixes: 727b3668b7 ("net: sfp: rework upstream interface")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I2C client is instantiated with I2C_CLIENT_WAKE flag (either via
"wakeup-source" device property, or via board info flag), it will mark the
main IRQ line as wakeup IRQ, which will ensure that it will be enabled for
wakeup when system transitions to suspend state. Since our suspend/resume
handlers were only managing IRQ wakeup state, they are no longer needed,
and can be removed.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I2C devices that are supposed to be wakeup sources should be instantiated
with I2C_CLIENT_WAKE flag (which can be either set by in board info, or
retrieved from "wakeup-source" property); individual drivers should not be
marking devices as wakeup sources unconditionally.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing if/else if/else on the chip's model number let's define
chip operations structure and use it to perform indirect calls. With number
of protocols supported by the driver growing, this makes it better
maintainable.
This change includes fixes to checks whether the driver should continue
polling the controller by Sven Van Asbroeck <thesven73@gmail.com>.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using devm_input_allocate_device() that set's up the parent for
us, no need to do it ourselves.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to using threaded IRQ so that we do not need to
manage the interrupt and work separately, and we do not acknowledge
interrupt until we finished handling it completely.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Tested-by: Marek Vasut <marex@denx.de> # ILI2117
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI2117 touch controller. This controller is similar
to the ILI210x and ILI251x, except for the following differences:
- Reading out of touch data must happen at most 300 mS after the
interrupt line was asserted. No command must be sent, the data
are returned upon pure I2C read of 43 bytes long.
- Supports 10 simultaneous touch inputs.
- Touch data format is slightly different.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org> # for DT binding
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the dump's time-stamp, use ktime_get_real in addition to
jiffies. This simplifies the user space implementation and bypasses
some inconsistent behavior with translating jiffies to current time.
The time taken is transformed into nsec, to comply with y2038 issue.
Fixes: c8e1da0bf9 ("devlink: Add health report functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update example in ad7879 device tree documentation to use generic touch
controller node names.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191026090403.3057-3-marcel@ziswiler.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If you prep a read (for example) that needs to get punted to async
context with a timer, if the timeout is sufficiently short, the timer
request will get completed with -ENOENT as it could not find the read.
The issue is that we prep and start the timer before we start the read.
Hence the timer can trigger before the read is even started, and the end
result is then that the timer completes with -ENOENT, while the read
starts instead of being cancelled by the timer.
Fix this by splitting the linked timer into two parts:
1) Prep and validate the linked timer
2) Start timer
The read is then started between steps 1 and 2, so we know that the
timer will always have a consistent view of the read request state.
Reported-by: Hrvoje Zeba <zeba.hrvoje@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't safely cancel under the inflight lock. If the work hasn't been
started yet, then io_wq_cancel_work() simply marks the work as cancelled
and invokes the work handler. But if the work completion needs to grab
the inflight lock because it's grabbing user files, then we'll deadlock
trying to finish the work as we already hold that lock.
Instead grab a reference to the request, if it isn't already zero. If
it's zero, then we know it's going through completion anyway, and we
can safely ignore it. If it's not zero, then we can drop the lock and
attempt to cancel from there.
This also fixes a missing finish_wait() at the end of
io_uring_cancel_files().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we have backpressure, for SQPOLL, we have one more condition
that warrants flagging that the application needs to enter the kernel:
we failed to submit IO due to backpressure. Make sure we catch that
and flag it appropriately.
If we run into backpressure issues with the SQPOLL thread, flag it
as such to the application by setting IORING_SQ_NEED_WAKEUP. This will
cause the application to enter the kernel, and that will flush the
backlog and clear the condition.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It's a little confusing that we have multiple types of command
cancellation opcodes now that we have a generic one. Make the generic
one work with POLL_ADD and TIMEOUT commands as well, that makes for an
easier to use API for the application. The fact that they currently
don't is a bit confusing.
Add a helper that takes care of it, so we can user it from both
IORING_OP_ASYNC_CANCEL and from the linked timeout cancellation.
Reported-by: Hrvoje Zeba <zeba.hrvoje@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One thing that really sucks for userspace APIs is if the kernel passes
back -ENOMEM/-EAGAIN for resource shortages. The application really has
no idea of what to do in those cases. Should it try and reap
completions? Probably a good idea. Will it solve the issue? Who knows.
This patch adds a simple fallback mechanism if we fail to allocate
memory for a request. If we fail allocating memory from the slab for a
request, we punt to a pre-allocated request. There's just one of these
per io_ring_ctx, but the important part is if we ever return -EBUSY to
the application, the applications knows that it can wait for events and
make forward progress when events have completed. This is the important
part.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.
[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8dfd ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org # v4.12+
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TUNNEL_OPTIONS_PRESENT (TUNNEL_GENEVE_OPT|TUNNEL_VXLAN_OPT|
TUNNEL_ERSPAN_OPT) flags should be set only according to
tb[LWTUNNEL_IP_OPTS], which is done in ip_tun_parse_opts().
When setting info key.tun_flags, the TUNNEL_OPTIONS_PRESENT
bits in tb[LWTUNNEL_IP(6)_FLAGS] passed from users should
be ignored.
While at it, replace all (TUNNEL_GENEVE_OPT|TUNNEL_VXLAN_OPT|
TUNNEL_ERSPAN_OPT) with 'TUNNEL_OPTIONS_PRESENT'.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Fixes: 32a2b002ce ("ipv6: route: per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
erspan v1 has OPT_ERSPAN_INDEX while erspan v2 has OPT_ERSPAN_DIR and
OPT_ERSPAN_HWID attributes, and they require different nlsize when
dumping.
So this patch is to get nlsize for erspan options properly according
to erspan version.
Fixes: b0a21810bd ("lwtunnel: add options setting and dumping for erspan")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the new options added in kernel, all should always use strict
parsing from the beginning with nla_parse_nested(), instead of
nla_parse_nested_deprecated().
Fixes: b0a21810bd ("lwtunnel: add options setting and dumping for erspan")
Fixes: edf31cbb15 ("lwtunnel: add options setting and dumping for vxlan")
Fixes: 4ece477870 ("lwtunnel: add options setting and dumping for geneve")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Why]
On Navi10, and presumably arcterus, updating pp_table via sysfs would
not re-scale the maximum possible power limit one can set. On navi10,
the SMU code ignored the power percentage overdrive setting entirely,
and would not allow you to exceed the default power limit at all.
[How]
Adding a function to the SMU interface to get the pptable version of the
default power limit allows ASIC-specific code to provide the correct
maximum-settable power limit for the current pptable.
v3: fix spelling (Alex)
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, navi10 overdrive settings could not be printed via
pp_od_clk_voltage
[How]
Implement printing for the overdrive settings for the following clocks
in navi10's ppt print_clk_levels implementation:
* SMU_OD_SCLK
* SMU_OD_MCLK
* SMU_OD_VDDC_CURVE
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, there was no way to set the gfxclk voltage curve in
the overdrive settings for navi10 through pp_od_clk_voltage
[How]
Add the required implementation to navi10's ppt dpm table editing
implementation, similar to the vega20 implementation and interface.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this patch, there was no way to use pp_od_clk_voltage on navi
[How]
Similar to the vega20 implementation, but using the common smc_v11_0
headers, implemented the pp_od_clk_voltage API for navi10's pptable
implementation
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
flush/cancel delayed works before doing finalization
to avoid concurrently requests.
Signed-off-by: Jesse Zhang <zhexi.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes the formatting on one comment and consolidates the
pci_get_drvdata() into the radeon_suspend_kms().
Signed-off-by: Kyle Mahlkuch <kmahlkuc@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When a custom powerplay table is provided, we need to update
the OD VDDC flag to avoid AVFS being enabled when it shouldn't be.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205393
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
xgmi, ras, hdcp and dtm ta are actually separated ucode and
need to handled case by case to upload to psp.
We support the case that ta binary have one or multiple of
them built-in. As a result, the driver should check each ta
binariy's availablity before decide to upload them to psp.
In the terminate (unload) case, the driver will check the
context readiness before perform unload activity. It's fine
to keep it as is.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
