Commit 016b87ca5c ("ACPI: EC: Rework flushing of pending work")
introduced a subtle bug into the flushing of pending EC work while
suspended to idle, which may cause the EC driver to fail to
re-enable the EC GPE after handling a non-wakeup event (like a
battery status change event, for example).
The problem is that the work item flushed by flush_scheduled_work()
in __acpi_ec_flush_work() may disable the EC GPE and schedule another
work item expected to re-enable it, but that new work item is not
flushed, so __acpi_ec_flush_work() returns with the EC GPE disabled
and the CPU running it goes into an idle state subsequently. If all
of the other CPUs are in idle states at that point, the EC GPE won't
be re-enabled until at least one CPU is woken up by another interrupt
source, so system wakeup events that would normally come from the EC
then don't work.
This is reproducible on a Dell XPS13 9360 in my office which
sometimes stops reacting to power button and lid events (triggered
by the EC on that machine) after switching from AC power to battery
power or vice versa while suspended to idle (each of those switches
causes the EC GPE to trigger for several times in a row, but they
are not system wakeup events).
To avoid this problem, it is necessary to drain the workqueue
entirely in __acpi_ec_flush_work(), but that cannot be done with
respect to system_wq, because work items may be added to it from
other places while __acpi_ec_flush_work() is running. For this
reason, make the EC driver use a dedicated workqueue for EC events
processing (let that workqueue be ordered so that EC events are
processed sequentially) and use drain_workqueue() on it in
__acpi_ec_flush_work().
Fixes: 016b87ca5c ("ACPI: EC: Rework flushing of pending work")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)
Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().
Otherwise undefined behavior might occur.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SET/CLEAR_FEATURE for Remote Wakeup allowance not handled correctly.
GET_STATUS handling provided not correct data on DATA Stage.
Issue seen when gadget's dr_mode set to "otg" mode and connected
to MacOS.
Both are fixed and tested using USBCV Ch.9 tests.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Fixes: fa389a6d77 ("usb: dwc2: gadget: Add remote_wakeup_allowed flag")
Tested-by: Jack Mitchell <ml@embed.me.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Moved ISOC request length checking from dwc2_hsotg_start_req() function to
dwc2_hsotg_ep_queue().
Fixes: 4fca54aa58 ("usb: gadget: s3c-hsotg: add multi count support")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:
- usb_gadget_vbus_draw() when called from set_config() and
composite_resume() will be passed the MaxPower value without
regard for the current connection speed, resulting in a
violation for USB 2.0 since the max is 500mA.
- the bMaxPower of the configuration descriptor would be
incorrectly encoded, again if the connection speed is only
at USB 2.0 or below, likely wrapping around U8_MAX since
the 2mA multiplier corresponds to a maximum of 510mA.
Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.
Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.
N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SuperSpeedPlus peripherals must report their bMaxPower of the
configuration descriptor in units of 8mA as per the USB 3.2
specification. The current switch statement in encode_bMaxPower()
only checks for USB_SPEED_SUPER but not USB_SPEED_SUPER_PLUS so
the latter falls back to USB 2.0 encoding which uses 2mA units.
Replace the switch with a simple if/else.
Fixes: eae5820b85 ("usb: gadget: composite: Write SuperSpeedPlus config descriptors")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Prior to commit eb9fecb9e6 ("usb: gadget: f_uac2: split out audio
core") the maximum packet size was calculated only from the high-speed
descriptor but now we use the largest of the full-speed and high-speed
descriptors.
This is correct, but the full-speed value is likely to be higher than
that for high-speed and this leads to submitting requests for OUT
transfers (received by the gadget) which are larger than the endpoint's
maximum packet size. These are rightly rejected by the gadget core.
config_ep_by_speed() already sets up the correct maximum packet size for
the enumerated speed in the usb_ep structure, so we can simply use this
instead of the overall value that has been used to allocate buffers for
requests.
Note that the minimum period for ALSA is still set from the largest
value, and this is unavoidable because it's possible to open the audio
device before the gadget has been enumerated.
Tested-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.
Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.
Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.
To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.
At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move the checking, buffer reserve and buffer commit code in
synth_event_trace_start/end() into inline functions
__synth_event_trace_start/end() so they can also be used by
synth_event_trace() and synth_event_trace_array(), and then have all
those functions use them.
Also, change synth_event_trace_state.enabled to disabled so it only
needs to be set if the event is disabled, which is not normally the
case.
Link: http://lkml.kernel.org/r/b1f3108d0f450e58192955a300e31d0405ab4149.1581374549.git.zanussi@kernel.org
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There's no reason to return -EINVAL when tracing a synthetic event if
it's soft disabled - treat it the same as if it were hard disabled and
return normally.
Have synth_event_trace() and synth_event_trace_array() just return
normally, and have synth_event_trace_start set the trace state to
disabled and return.
Link: http://lkml.kernel.org/r/df5d02a1625aff97c9866506c5bada6a069982ba.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad95 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If the ring_buffer reserve in synth_event_trace_start() fails, the
matching ring_buffer_nest_end() should be called in the error code,
since nothing else will ever call it in this case.
Link: http://lkml.kernel.org/r/20abc444b3eeff76425f895815380abe7aa53ff8.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad95 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull cgroup fix from Tejun Heo:
"I made a mistake while removing cgroup task list lazy init
optimization making the root cgroup.procs show entries for the
init_tasks. The zero entries doesn't cause critical failures but does
make systemd print out warning messages during boot.
Fix it by omitting init_tasks as they should be"
* 'for-5.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: init_tasks shouldn't be linked to the root cgroup
With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:
make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127
Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)
Also, separate handling of each of the lists to its own shell command.
The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 5f70bde26a ("selftests: fix build behaviour on targets' failures")
added a logic to track failure of builds of individual targets. However, it
does exactly the opposite of what a distro kernel needs: we create a RPM
package with a selected set of selftests and we need the build to fail if
build of any of the targets fail.
Both use cases are valid. A distribution kernel is in control of what is
included in the kernel and what is being built; any error needs to be
flagged and acted upon. A CI system that tries to build as many tests as
possible on the best effort basis is not really interested in a failure here
and there.
Support both use cases by introducing a FORCE_TARGETS variable. It is
switched off by default to make life for CI systems easier, distributions
can easily switch it on while building their packages.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
tpm2 tests set fails if there is no /dev/tpm0 and /dev/tpmrm0
supported. Check if these files exist before run and mark test as
skipped in case of absence.
Signed-off-by: Nikita Sobolev <Nikita.Sobolev@synopsys.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
While running the ftracetests, the pid filter test failed because the
instance "foo" existed, and it was using it to rerun the test under a
instance named foo. The collision caused the test to fail as the mkdir
failed as the name already existed.
As of commit b5b77be812 ("selftests: ftrace: Allow some tests to be run
in a tracing instance") all a selftest needs to do to be tested in an
instance is to set the "instance" flag. There's no reason a selftest needs
to create an instance to run its test in an instance directly.
Remove the open coded testing in an instance for the pid filter test and
have it set the "instance" flag instead.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
There is a spelling mistake in a literal string, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=0cTj
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20200210' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Two small fixes: one fixes a locking problem in the recently merged
label translation code, the other fixes an embarrassing 'binderfs' /
'binder' filesystem name check"
* tag 'selinux-pr-20200210' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix sidtab string cache locking
selinux: fix typo in filesystem name
Commit e567cb3fef30 ("MAINTAINERS: add an entry for kfifo") added a new
entry to MAINTAINERS. Following the example of the previous entry on the
list I added a trailing ':' character at the end of the title line.
This however results in rather strange looking output from
scripts/get_maintainer.pl:
$ ./scripts/get_maintainer.pl ./0001-kfifo.patch
Stefani Seibold <stefani@seibold.net> (maintainer:KFIFO:)
linux-kernel@vger.kernel.org (open list)
It turns out there are more entries like this. Fix the entire file by
removing all trailing colons.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200130135515.30359-1-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
kernel/bpf/btf.c:4131:5: warning: symbol 'btf_check_func_type_match' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200210011441.147102-1-yaohongbo@huawei.com
Fix following build error. We could push a tcp.h header into one of the
include paths, but I think its easy enough to simply pull in the three
defines we need here. If we end up using more of tcp.h at some point
we can pull it in later.
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c: In function ‘connected_socket_v4’:
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:20:11: error: ‘TCP_REPAIR_ON’ undeclared (first use in this function)
repair = TCP_REPAIR_ON;
^
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:20:11: note: each undeclared identifier is reported only once for each function it appears in
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:29:11: error: ‘TCP_REPAIR_OFF_NO_WP’ undeclared (first use in this function)
repair = TCP_REPAIR_OFF_NO_WP;
Then with fix,
$ ./test_progs -n 44
#44/1 sockmap create_update_free:OK
#44/2 sockhash create_update_free:OK
#44 sockmap_basic:OK
Fixes: 5d3919a953 ("selftests/bpf: Test freeing sockmap/sockhash with a socket in it")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/158131347731.21414.12120493483848386652.stgit@john-Precision-5820-Tower
Suppress non-error messages when applying new bootconfig
to initrd image. To enable it, replace printf for error
message with pr_err() macro.
This also adds a testcase for this fix.
Link: http://lkml.kernel.org/r/158125351377.16911.13283712972275131160.stgit@devnote2
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
To reduce the large static array from kernel data, allocate
xbc_nodes array dynamically only if the kernel loads a
bootconfig.
Note that this also add dummy memblock.h for user-spacae
bootconfig tool.
Link: http://lkml.kernel.org/r/158108569699.3187.6512834527603883707.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Commit a6dbe44275 ("vt: perform safe console erase in the right
order") provided fixes to an earlier commit by gathering all console
scrollback flushing operations in a function of its own. This includes
the invocation of vc_sw->con_switch() as previously done through a
update_screen() call. That commit failed to carry over the
con_is_visible() conditional though, as well as cursor handling, which
caused problems when "\e[3J" was written to a background console.
One could argue for preserving the call to update_screen(). However
this does far more than we need, and it is best to remove scrollback
assumptions from it. Instead let's gather the minimum needed to actually
perform scrollback flushing properly in that one place.
While at it, let's document the vc_sw->con_switch() side effect being
relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-and-tested-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2001281205560.1655@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently CONFIG_FSI_MASTER_ASPEED=y implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/fsi/fsi-master-aspeed.o: in function `fsi_master_aspeed_probe':
drivers/fsi/fsi-master-aspeed.c:436: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Fixes: 606397d67f ("fsi: Add ast2600 master driver")
Cc: stable@vger.kernel.org
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200131034832.294268-1-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly state that all contributions to the kernel source tree
really are covered under this COPYING file in case someone thought
otherwise. Lawyers love to be pedantic, even more so than software
engineers at times, and this sentence makes them sleep easier.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200206154800.GA3754085@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter's email address bounces, so remove him as the contact for Amazon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200205122551.GA1185549@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to get an instant RX timeout or end-of-transfer interrupt
before RX DMA was started, if transaction is less than 16 bytes. Transfer
should be handled in PIO mode in this case because DMA can't handle it.
This patch brings back the original behaviour of the driver that was
changed by accident by a previous commit, it fixes occasional Bluetooth HW
initialization failures which I started to notice recently.
Fixes: d5e3fadb70 ("tty: serial: tegra: Activate RX DMA transfer by request")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200209164415.9632-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.
Fixes: 98f2082c3a ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serdev tty-port controller driver should reset the tty-port client
operations also on deregistration to avoid a NULL-pointer dereference in
case the port is later re-registered as a normal tty device.
Note that this can only happen with tty drivers such as 8250 which have
statically allocated port structures that can end up being reused and
where a later registration would not register a serdev controller (e.g.
due to registration errors or if the devicetree has been changed in
between).
Specifically, this can be an issue for any statically defined ports that
would be registered by 8250 core when an 8250 driver is being unbound.
Fixes: bed35c6dfa ("serdev: add a tty port controller driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200210145730.22762-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 56d5893615 ("kbuild: do not create orphan built-in.a or
obj-y objects"), scripts/link-vmlinux.sh does nothing when descending
into init/.
Once the version number becomes out of sync between .version and
include/generated/compile.h, it is not self-healing.
[How to reproduce]
$ echo 100 > .version
$ make
You will see the number in the .version is always bigger than that in
compile.h by one. After this, every time you run 'make', the vmlinux is
re-linked even when none of source files is updated.
Fixes: 56d5893615 ("kbuild: do not create orphan built-in.a or obj-y objects")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
memcpy() writes one more byte than allocated.
Fixes: 8d60526999 ("scripts/kallsyms: change table to store (strcut sym_entry *)")
Reported-by: youling257 <youling257@gmail.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Use the more optimized strlist implementation to do the idle function
lookup.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Acked-by: Song Liu <songliubraving@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200210163147.25358-1-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The "acpi_idle_do_entry", "acpi_processor_ffh_cstate_enter", and
"idle_cpu" symbols appear in 'perf top' output, at least on AMD systems.
Add them to perf's idle_symbols list, so they don't dominate 'perf top'
output.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200207230613.26709-2-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For data collected on machines with front end stalled cycles supported,
such as found on modern AMD CPU families, commit 146540fb54 ("perf
stat: Always separate stalled cycles per insn") introduces a new line in
CSV output with a leading comma that upsets some automated scripts.
Scripts have to use "-e ex_ret_instr" to work around this issue, after
upgrading to a version of perf with that commit.
We could add "if (have_frontend_stalled && !config->csv_sep)" to the not
(total && avg) else clause, to emphasize that CSV users are usually
scripts, and are written to do only what is needed, i.e., they wouldn't
typically invoke "perf stat" without specifying an explicit event list.
But - let alone CSV output - why should users now tolerate a constant
0-reporting extra line in regular terminal output?:
BEFORE:
$ sudo perf stat --all-cpus -einstructions,cycles -- sleep 1
Performance counter stats for 'system wide':
181,110,981 instructions # 0.58 insn per cycle
# 0.00 stalled cycles per insn
309,876,469 cycles
1.002202582 seconds time elapsed
The user would not like to see the now permanent:
"0.00 stalled cycles per insn"
line fixture, as it gives no useful information.
So this patch removes the printing of the zeroed stalled cycles line
altogether, almost reverting the very original commit fb4605ba47
("perf stat: Check for frontend stalled for metrics"), which seems like
it was written to normalize --metric-only column output of common Intel
machines at the time: modern Intel machines have ceased to support the
genericised frontend stalled metrics AFAICT.
AFTER:
$ sudo perf stat --all-cpus -einstructions,cycles -- sleep 1
Performance counter stats for 'system wide':
244,071,432 instructions # 0.69 insn per cycle
355,353,490 cycles
1.001862516 seconds time elapsed
Output behaviour when stalled cycles is indeed measured is not affected
(BEFORE == AFTER):
$ sudo perf stat --all-cpus -einstructions,cycles,stalled-cycles-frontend -- sleep 1
Performance counter stats for 'system wide':
247,227,799 instructions # 0.63 insn per cycle
# 0.26 stalled cycles per insn
394,745,636 cycles
63,194,485 stalled-cycles-frontend # 16.01% frontend cycles idle
1.002079770 seconds time elapsed
Fixes: 146540fb54 ("perf stat: Always separate stalled cycles per insn")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200207230613.26709-1-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use the new usb-device pointer instead of back-casting when accessing
the struct usb_device when parsing endpoints.
Note that this introduces two lines that are longer than 80 chars on
purpose.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tools like Coccinelle may erroneously recommend to use the
devm_platform_ioremap_resource() API for the registers mapping because
these tools are not aware about the implementation details of the driver.
Let's add a clarifying comments to the code, which should help to stop
future attempts to break the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200202224259.29187-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.
Such a request was added by commit a4f55d8b8c ("usb: hub: Check
device descriptor before resusciation"). It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).
The same kind of thing occurs when a port's power session is lost
during system suspend. When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits. The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway. By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing. There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.
Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else. The underlying cause of
Paul's problem lies in his Bluetooth adapter. Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.
The work thread performs its check when it sees that the port's bit is
set in hub->change_bits. In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.
One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits. But it seems simpler to just avoid
setting the bit during hub_activate() in the first place. That's what
this patch does.
(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought. In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes. During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)
Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To work properly on every architectures and compilers, the enum value
needs to be specific numbers.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1580537624-10179-1-git-send-email-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.
There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.
In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.
In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.
The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.
In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.
Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.
[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
[ 74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
[ 74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.077303] usb 5-1.1: Product: Ultra
[ 74.080980] usb 5-1.1: Manufacturer: SanDisk
[ 74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550
[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
[ 34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.604430] usb 6-1.1: Product: Ultra
[ 34.608110] usb 6-1.1: Manufacturer: SanDisk
[ 34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
