PMU registration is successfully completed by Device Tree now, so
there is no longer a requirement to register it from platform code.
This patch removes platform registration during a DT boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All Device Tree enablement for Snowball's Platform devices; LEDs, Keys,
Ethernet and all associated AB8500 Multi-Functional Devices are now
complete, so here we remove any trace of adding those devices when Device
Tree is enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention. This patch ensures the
sleepmode property adheres to the rules.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During a Device Tree boot, all probing will now be completed on parse
of the Device Tree binary. In the same patch we remove platform
registration of the Real Time Clock.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add a node for the AB8500 Real Time Clock in all devices
supporting the DB8500. The AB8500 RTC driver makes use of named
interrupts we provide support for this too.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8500 driver has now been provided with IRQ domain support. This
means we can request IRQs from any of it's uses via Device Tree. This
patch advertises the AB8500 as an Interrupt Controller and provides the
correct calls in the format the driver expects.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This node has no properties. It merely allows probing of the
ab8500-debugfs driver during Device Tree initialisation.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we specify each of the ab8500 USB driver's seven IRQs, which the
driver references by name. We also apply regulator support for the
three used by the device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the DT node for the misc/ab8500-pwm driver. It will
allow probing of the driver during a Device Tree enabled boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the DT node for the mfd/ab8500-sysctrl driver. It will
allow probing of the driver during a Device Tree enabled boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch configures the user LED on Snowball to double flash
every second or so, whilst it's still alive. This can give key
indications as to what the board is doing in the case of no
console output.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch configures the user LED on Snowball to double flash
every second or so, whilst it's still alive. This can give key
indications as to what the board is doing in the case of no
console output.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch provides support for the ab8500-gpadc driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch enables and illuminates the user_led on the
Snowball low-cost development board using DT. It also
removes initialisation carried out from platform code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Code exists in the mop500 board file (used for HREF and Snowball)
to initialise Snowball's user LED via the leds-gpio driver. However,
the driver isn't currently built when using the current configuration.
This patch aims to change that behavior.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch provides a way for find_clk() to complete its name-based
searches and still find the nmk-i2c clocks. As Device Tree has a
different naming structure to that of more traditional initialisation
methods, find_clk() not succeed without these bindings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that u5500 is obsolete, u8500 is the only user of the Nomadik
i2c driver. As such there is no requirement to differentiate between
initialisation values. By the time a new SoC is released, almost all
of the ux500 platform will be DT:ed, so we can make decisions based
on the compatible property instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The iommu pool patch has a bug where it would cause a crash when using
only one pool (based on the size of the DMA window).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The rework of the snd-usb endpoint logic moved the calls to
snd_usb_set_interface() into the snd_usb_endpoint implemenation. This
changed the order in which these calls are issued to the device, and
thereby caused regressions for some webcams.
Fix this by moving the calls back to pcm.c for now to make it work again
and use snd_usb_endpoint_activate() to really tear down all remaining
URBs in the flight, consequently fixing another regression caused by USB
packets on the wire after altsetting 0 has been selected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Philipp Dreimann <philipp@dreimann.net>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This change adds support for old Hanwang Art master II tablet
Signed-off-by: weixing <weixing@hanwang.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some platform it may happen that the input clock to keyboard may
change during suspend, thus impacting its wakeup capability.
There is no means for keyboard driver to know this frequency before
hand. Hence introduce a platform data 'suspended_rate' which indicates
the frequency during suspend at which keyboard operates.
Accordingly reprogram keyboard while going into suspend and restore
original configuration at the time of resume.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
SPEAr keyboard should normally disable clock during suspend and enable it
during resume.
For cases where it is expected to act as a wakeup source the clock can
remain in the same state i.e. kept enabled if it is being used.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: Yuri Khan <yurivkhan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TWI bit mask macros are moved to twi head file.
Depend on commit 61c16b5c74
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Current driver was developed based on BF537 0.2 HRM. In high system load, BUFRDERR error
interrupt may be raised if XMTSERV interrupt of last TX byte is not served in time
(set RSTART bit), which breaks restart tranfer as expected.
"Buffer Read Error (BUFRDERR)" description in Blackfin HRM only applys to BF537
rev. < 0.3. In later rev. and later announced Blackfin chips, such as BF527 and
BF548, a new TWI master feature "Clock Stretching" is added into the TWI controller,
BUFRDERR interrupt is not triggered after TX FIFO is empty.
This patch sets RSTART bit at the beginning of the first transfer. The SCL and SDA
is hold till XMTSERV interrupt of last TX byte is served. Restart transfer is not broken
in high system load.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In order to mark I2C transfer fail when MEN bit in I2C controller is
reset unexpectedly in MCOMP interrupt, interrupt status bits XMTSERV or
RCVSERV should be checked.
Master Transfer Complete (MCOMP).
[1] The initiated master transfer has completed. In the absence of a
repeat start, the bus has been released.
[0] The completion of a transfer has not been detected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[wsa: fixed spaces around operators and typo in commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Checking for adc->ts_pend already claimed should be done with the
lock held.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The rate of xusbxti clock is set in individual machine files.
The default value should be defined at the clock definition
and individual machine files should modify it if required.
Division by zero in kernel.
[<c0011849>] (unwind_backtrace+0x1/0x9c) from [<c022c663>] (Ldiv0+0x9/0x12)
[<c022c663>] (Ldiv0+0x9/0x12) from [<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78)
[<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78) from [<c0019e67>] (clk_set_rate+0x2f/0x78)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some fault i2c device may hold the sda/scl line and cause i2c driver
wait in the BUS busy loop. The I2C framework already retry the
transfer loop before timeout. Return -EAGAIN instead of pull BUSBUSY
in the other loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
For transfer counts > 255 bytes i2c-bfin-twi sets the data
transfer counter DCNT to 0xFF indicating unlimited transfers.
It then uses a flag iface->manual_stop to manually issue the STOP
condition, once the required amount of bytes are received.
We found that on I2C receive operation issuing the STOP condition
together with a FULL RCV FIFO (2bytes) will cause SDA and SCL be
constantly driven low.
This patch stops receiving operation immediately in last rx interrupt.
This patch also wakes up waiting process when transfer completes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
For transfer counts > 255 bytes i2c-bfin-twi sets the data
transfer counter DCNT to 0xFF indicating unlimited transfers.
It then uses a flag iface->manual_stop to manually issue the STOP
condition, once the required amount of bytes are received.
We found that on I2C receive operation issuing the STOP condition
together with a FULL RCV FIFO (2bytes) will cause SDA and SCL be
constantly driven low.
Temporary workaround until further investigation:
Discard the RCV FIFO before issuing the STOP condition.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add node for EXYNOS4 interrupt combiner controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for device based discovery.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The set_level callback in the controller data, which is used to configure
the slave select line, cannot be supported when migrating the driver to
device tree based discovery. Since all the platforms currently use gpio
as the slave select line, this callback can be removed from the
controller data and replaced with call to gpio_set_value in the driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With the spi controller hardware configuration moved into the driver data, there
are no more default hardware configuration data that is passed through platform
data. Accordingly, the s3c64xx_spi{0|1|2}_set_platdata functions are adapted to
these changes.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The platform data pointer that is passed to the spi gpio setup functions
is not used. Hence, this parameter is removed from all the spi gpio setup
functions.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Platform data is used to specify controller hardware specific information
such as the tx/rx fifo level mask and bit offset of rx fifo level. Such
information is not suitable to be supplied from device tree. Instead,
it can be moved into the driver data and removed from platform data.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The macro S3C64XX_SPI_ST_TRLCNTZ is not used and hence it is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 4972a80e16 (ARM: SAMSUNG: Add device tree support for pl330 dma
engine wrappers) introduced a new member 'dt_dmach_prop' in the struct
samsung_dma_info which is used to specify the dma channel number property
as obtained from the device tree. It also introduced a new dma request id
'DMACH_DT_PROP' to indicate that a device tree node property represting
the dma channel is available in 'struct samsung_dma_info'.
Add dma request id 'DMACH_DT_PROP' in s3c64xx dma channel id list in order
to maintain compatibility to the changes in the Samsung dma wrappper
operations.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The shdma base library has originally been extracted from the shdma driver,
which now can be converted to actually use it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
