The EHCI driver is not stable enough to be enabled by default. In v3.5,
it has at least the following problems:
- warning dump during bootup
- hang during suspend
- prevents CORE powerdomain from entering retention during idle (even
when no USB devices connected.)
This demonstrates that this driver has not been thoroughly tested and
therfore should not be enabled in the default defconfig.
In addition, the problems above cause new PM regressions which need be
addressed before this driver should be enabled in the default
defconfig.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit c0357e975a
bnx2: stop using net_device.{base_addr, irq}.
removed netdev->base_addr so we need to update cnic to get the MMIO
base address from pci_resource_start(). Otherwise, mmap of the uio
device will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a device with limited QMI support. It does not support
normal QMI_WDS commands for connection management. Instead,
sending a QMI_CTL SET_INSTANCE_ID command is required to
enable the network interface:
01 0f 00 00 00 00 00 00 20 00 04 00 01 01 00 00
A number of QMI_DMS and QMI_NAS commands are also supported
for optional device management.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
we set max_prioidx to the first zero bit index of prioidx_map in
function get_prioidx.
So when we delete the low index netprio cgroup and adding a new
netprio cgroup again,the max_prioidx will be set to the low index.
when we set the high index cgroup's net_prio.ifpriomap,the function
write_priomap will call update_netdev_tables to alloc memory which
size is sizeof(struct netprio_map) + sizeof(u32) * (max_prioidx + 1),
so the size of array that map->priomap point to is max_prioidx +1,
which is low than what we actually need.
fix this by adding check in get_prioidx,only set max_prioidx when
max_prioidx low than the new prioidx.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments were wrong here because "AX25_MAX_DIGIS" is 8 but the
comments say 6. Also I've changed the "7" to "AX25_ADDR_LEN".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, we should change ETH_P_IP from host endian
to big endian, htons, not ntohs.
CC: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With lockdep enabled we get:
=============================================
[ INFO: possible recursive locking detected ]
3.4.4-Cavium-Octeon+ #313 Not tainted
---------------------------------------------
kworker/u:1/36 is trying to acquire lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813da7e8>] mdio_mux_read+0x38/0xa0
but task is already holding lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813d79e4>] mdiobus_read+0x44/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&bus->mdio_lock);
lock(&bus->mdio_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
.
.
.
This is a false positive, since we are indeed using 'nested' locking,
we need to use mutex_lock_nested().
Now in theory we can stack multiple MDIO multiplexers, but that would
require passing the nesting level (which is difficult to know) to
mutex_lock_nested(). Instead we assume the simple case of a single
level of nesting. Since these are only warning messages, it isn't so
important to solve the general case.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
broadcom, not marvell.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB and SR-IOV cannot currently be enabled at the same time as the queueing
schemes are incompatible. If they are both enabled it will result in Tx
hangs since only the first Tx queue will be able to transmit any traffic.
This simple fix for this is to block us from enabling TCs in ixgbe_setup_tc
if SR-IOV is enabled. This change will be reverted once we can support
SR-IOV and DCB coexistence.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx phys don't support autonegotiation, so don't use it by
default, as otherwise phy_state_machine() will try to enable it (using
c22 requests, which also don't make any sense for the bcm78xx).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable interrupts if it is not our interrupt
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Optima EEE chipset.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OFF carrier state is setup in probe() open() and suspend() functions.
The carrier ON state is managed in macb_handle_link_change().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two netem bugs :
1) When a frame was dropped by tfifo_enqueue(), drop counter
was incremented twice.
2) When reordering is triggered, we enqueue a packet without
checking queue limit. This can OOM pretty fast when this
is repeated enough, since skbs are orphaned, no socket limit
can help in this situation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mark Gordon <msg@google.com>
Cc: Andreas Terzis <aterzis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
some people report atl1c could cause system hang with following
kernel trace info:
---------------------------------------
WARNING: at.../net/sched/sch_generic.c:258 dev_watchdog+0x1db/0x1d0()
...
NETDEV WATCHDOG: eth0 (atl1c): transmit queue 0 timed out
...
---------------------------------------
This is caused by netif_stop_queue calling when cable Link is down.
So remove netif_stop_queue, because link_watch will take it over.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Cloud Ren <cjren@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing some recent work on sctp sack bundling I noted that
sctp_packet_append_chunk was pretty inefficient. Specifially, it was called
recursively while trying to bundle auth and sack chunks. Because of that we
call sctp_packet_bundle_sack and sctp_packet_bundle_auth a total of 4 times for
every call to sctp_packet_append_chunk, knowing that at least 3 of those calls
will do nothing.
So lets refactor sctp_packet_bundle_auth to have an outer part that does the
attempted bundling, and an inner part that just does the chunk appends. This
saves us several calls per iteration that we just don't need.
Also, noticed that the auth and sack bundling fail to free the chunks they
allocate if the append fails, so make sure we add that in
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to the new i.mx clock conversion the mx27 silicon version was printed at boot.
Reenable this feature.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit a1c7fff7e1 (net: netdev_alloc_skb() use build_skb()) broke b44 on
some 64bit machines.
It appears b44 and b43 use __netdev_alloc_skb() instead of alloc_skb()
for their bounce buffers.
There is no need to add an extra NET_SKB_PAD reservation for bounce
buffers :
- In TX path, NET_SKB_PAD is useless
- In RX path in b44, we force a copy of incoming frames if
GFP_DMA allocations were needed.
Reported-and-bisected-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRV_MODULE_VERSION here is "2.7.2.2" which is only 8 chars but we copy
12 bytes from the stack so it's a small information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when sending data over datagram, the send function will attempt to
allocate any size passed on from the userspace.
We should make sure that this size is checked and limited. We'll limit it
to the MTU of the device, which is checked later anyway.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug has been present ever since data-check was introduce
in 2.6.16. However it would only fire if a data-check were
done on a degraded array, which was only possible if the array
has 3 or more devices. This is certainly possible, but is quite
uncommon.
Since hot-replace was added in 3.3 it can happen more often as
the same condition can arise if not all possible replacements are
present.
The problem is that as soon as we submit the last read request, the
'r1_bio' structure could be freed at any time, so we really should
stop looking at it. If the last device is being read from we will
stop looking at it. However if the last device is not due to be read
from, we will still check the bio pointer in the r1_bio, but the
r1_bio might already be free.
So use the read_targets counter to make sure we stop looking for bios
to submit as soon as we have submitted them all.
This fix is suitable for any -stable kernel since 2.6.16.
Cc: stable@vger.kernel.org
Reported-by: Arnold Schulz <arnysch@gmx.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Profiling indicates that MR validation locking is expensive. The MR
table is largely read-only and is a suitable candidate for RCU locking.
The patch uses RCU locking during validation to eliminate one
lock/unlock during that validation.
Reviewed-by: Mike Heinz <michael.william.heinz@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A timing issue can occur where qib_mr_dereg can return -EBUSY if the
MR use count is not zero.
This can occur if the MR is de-registered while RDMA read response
packets are being progressed from the SDMA ring. The suspicion is
that the peer sent an RDMA read request, which has already been copied
across to the peer. The peer sees the completion of his request and
then communicates to the responder that the MR is not needed any
longer. The responder tries to de-register the MR, catching some
responses remaining in the SDMA ring holding the MR use count.
The code now uses a get/put paradigm to track MR use counts and
coordinates with the MR de-registration process using a completion
when the count has reached zero. A timeout on the delay is in place
to catch other EBUSY issues.
The reference count protocol is as follows:
- The return to the user counts as 1
- A reference from the lk_table or the qib_ibdev counts as 1.
- Transient I/O operations increase/decrease as necessary
A lot of code duplication has been folded into the new routines
init_qib_mregion() and deinit_qib_mregion(). Additionally, explicit
initialization of fields to zero is now handled by kzalloc().
Also, duplicated code 'while.*num_sge' that decrements reference
counts have been consolidated in qib_put_ss().
Reviewed-by: Ramkrishna Vepa <ramkrishna.vepa@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
An MR reference leak exists when handling UC RDMA writes with
immediate data because we manipulate the reference counts as if the
operation had been a send.
This patch moves the last_imm label so that the RDMA write operations
with immediate data converge at the cq building code. The copy/mr
deref code is now done correctly prior to the branch to last_imm.
Reviewed-by: Edward Mascarenhas <edward.mascarenhas@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These macros will be reused by the mlx4 SRIOV-IB CM paravirtualization
code, and there is no reason to have them declared both in the IB core
in the mlx4 IB driver.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This query is needed for SRIOV alias GUID support.
The query is implemented per the IB Spec definition
in section 15.2.5.18 (GuidInfoRecord).
Signed-off-by: Erez Shitrit <erezsh@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Define pr_fmt and add some pr_debug prints.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, VFs have 0 in their dev->caps.function field. This is a
valid pci id (usually of the PF). Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
sparse correctly warns that if mpa->private_data_size is __be16, then
doing += on it is wrong, even if we do += htons(<something>) -- on a
little endian system, carries will go the wrong way. Fix this up by
doing the addition in native byte order.
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Provide an option for the user to specify that listens should only
accept connections where the incoming address family matches that of
the locally bound address. This is used to support the equivalent of
IPV6_V6ONLY socket option, which allows an app to only accept
connection requests directed to IPv6 addresses.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The rdma_cm maps IPv4 and IPv6 addresses to the same service ID. This
prevents apps from listening only for IPv4 or IPv6 addresses. It also
results in an app binding to an IPv4 address receiving connection
requests for an IPv6 address.
Change this to match socket behavior: restrict listens on IPv4
addresses to only IPv4 addresses, and if a listen is on an IPv6
address, allow it to receive either IPv4 or IPv6 addresses, based on
its address family binding.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The RDMA CM uses a single port space for all associated (tcp, udp,
etc.) port bindings, regardless of the address family that the user
binds to. The result is that if a user binds to AF_INET, but does not
specify an IP address, the bind will occur for AF_INET6. This causes
an attempt to bind to the same port using AF_INET6 to fail, and
connection requests to AF_INET6 will match with the AF_INET listener.
Align the behavior with sockets and restrict the bind to AF_INET only.
If a user binds to AF_INET6, we bind the port to AF_INET6 and
AF_INET depending on the value of bindv6only.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since ee7cd8981e 'virtio: expose added
descriptors immediately.', in virtio balloon virtqueue_get_buf might
now run concurrently with virtqueue_kick. I audited both and this
seems safe in practice but this is not guaranteed by the API.
Additionally, a spurious interrupt might in theory make
virtqueue_get_buf run in parallel with virtqueue_add_buf, which is
racy.
While we might try to protect against spurious callbacks it's
easier to fix the driver: balloon seems to be the only one
(mis)using the API like this, so let's just fix balloon.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed unused var)
ARRAY_SIZE() may be larger than the number of supplies actually used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
References to the WM5102 tables need to be guarded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We're testing for a specific value and while SPI does not detect I/O
errors I2C can.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensures we don't leak the enable we just did.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These registers will be used in future devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures that if we are using a GPIO as a wake source it continues to
function while we're suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now we have regcache sync region we can use it to do a more efficient
sync of the pin configuration after we reset the device during suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While the core isn't useful by itself it does depend on regmap so try to
force that on.
Reported-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8pCq
-----END PGP SIGNATURE-----
Merge tag 'mfd/wm5102' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into for-next
mfd: Initial support for Wolfson Arizona platform and WM5102 devices
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
During conversion to regmap_irq this hunk was missing being moved
to MFD driver to put the chip into clear on read mode. Also as slave
is now set use it to determine which slave for the register call.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a merge error the section of code passing the pdata for the
regulator driver to the mfd_add_devices via the children structure
was missing. This corrects this problem.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
