Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().
At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.
It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.
The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.
The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.
These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.
The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current mail address is rejected, last activity (with a different
address) in git-history is from 2012. Remove this.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove cite "Not sure what this does, but it is absolutely essential".
Extract initialization of trackstick part when touchpad is in passthrough
mode for v3 and v6 protocols into own function. Initialization for v3 is:
setscale11, setscale11, setscale11, nibble 0x9, nibble 0x4. Initialization
for v6 is: setscale11, setscale11, setscale11, setrate 0xC8, setrate 0x14.
Nibbles 0x9 and 0x4 for v3 protocol correspond to setrate 0xC8 and 0x14,
therefore these sequences are same.
When touchpad is in passthrough mode, then OS communicates with trackstick
and this sequence is some magic vendor PS/2 command to put trackstick into
"extended" mode. After that sequence trackstick starts reporting packets in
some vendor 4 bytes format (first byte is always 0xE8).
Next step after configuring trackstick to be in "extended" mode, is to
configure touchpad for v3 protocol to expect that trackstick reports data
in "extended" mode. For v3 protocol this is done by setting bit 1 in
register 0xC2C8 (offset 0x08 from base address 0xC2C0).
When both touchpad and trackstick are not configured for "extended" mode
then touchpad reports trackstick packets in different format, which is not
supported by psmouse/alps driver (yet).
In Cirque documentation GP-AN- 130823 INTERFACING TO GEN4 OVER I2C (PDF)
available at http://www.cirque.com/gen4-dev-resources is Logical Address
0xC2C8 named as PS2AuxControl and Bit Number 1 as ProcessAuxExtendedData
with description: Auxiliary device data is assumed to be extended data when
set.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John Fastabend says:
====================
While testing sockmap with more programs (besides our test programs)
I found a couple issues.
The attached series fixes an issue where pinned maps were not
working correctly, blocking sockets returned zero, and an error
path that when the sock hit an out of memory case resulted in a
double page_put() while doing ingress redirects.
See individual patches for more details.
v2: Incorporated Daniel's feedback to use map ops for uref put op
which also fixed the build error discovered in v1.
v3: rename map_put_uref to map_release_uref
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the case where the socket memory boundary is hit the redirect
path returns an ENOMEM error. However, before checking for this
condition the redirect scatterlist buffer is setup with a valid
page and length. This is never unwound so when the buffers are
released latter in the error path we do a put_page() and clear
the scatterlist fields. But, because the initial error happens
before completing the scatterlist buffer we end up with both the
original buffer and the redirect buffer pointing to the same page
resulting in duplicate put_page() calls.
To fix this simply move the initial configuration of the redirect
scatterlist buffer below the sock memory check.
Found this while running TCP_STREAM test with netperf using Cilium.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the recvmsg handler we need to add a wait event to support the
blocking use cases. Without this we return zero and may confuse
user applications. In the wait event any data received on the
sk either via sk_receive_queue or the psock ingress list will
wake up the sock.
Fixes: fa246693a1 ("bpf: sockmap, BPF_F_INGRESS flag for BPF_SK_SKB_STREAM_VERDICT")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Relying on map_release hook to decrement the reference counts when a
map is removed only works if the map is not being pinned. In the
pinned case the ref is decremented immediately and the BPF programs
released. After this BPF programs may not be in-use which is not
what the user would expect.
This patch moves the release logic into bpf_map_put_uref() and brings
sockmap in-line with how a similar case is handled in prog array maps.
Fixes: 3d9e952697 ("bpf: sockmap, fix leaking maps with attached but not detached progs")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Per Documentation/bpf/bpf_devel_QA.txt add the -target flag to the
sockmap Makefile. Relevant text quoted here,
Otherwise, you can use bpf target. Additionally, you _must_ use
bpf target when:
- Your program uses data structures with pointer or long / unsigned
long types that interface with BPF helpers or context data
structures. Access into these structures is verified by the BPF
verifier and may result in verification failures if the native
architecture is not aligned with the BPF architecture, e.g. 64-bit.
An example of this is BPF_PROG_TYPE_SK_MSG require '-target bpf'
Fixes: 69e8cc134b ("bpf: sockmap sample program")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF_PROG_TYPE_SK_MSG programs use a 'void *' for both data and the
data_end pointers. Additionally, the verifier ensures that every
accesses into the values is a __u64 read. This correctly maps on
to the BPF 64-bit architecture.
However, to ensure that when building on 32bit architectures that
clang uses correct types the '-target bpf' option _must_ be
specified. To make this clear add a note to the Documentation.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Before [1], When MAC address of the netdevice is changed, default GID is
supposed to get deleted and added back which affects the node and/or port
GUID in below sequence.
netdevice_event()
-> NETDEV_CHANGEADDR
default_del_cmd()
del_netdev_default_ips()
bond_delete_netdev_default_gids()
ib_cache_gid_set_default_gid()
ib_cache_gid_del()
add_cmd()
[..]
However, ib_cache_gid_del() was not getting invoked in non bonding
scenarios because event_ndev and rdma_ndev are same.
Therefore, fix such condition to ignore checking upper device when event
ndev and rdma_dev are same; similar to bond_set_netdev_default_gids().
Which this fix ib_cache_gid_del() is invoked correctly; however
ib_cache_gid_del() doesn't find the default GID for deletion because
find_gid() was given default_gid = false with
GID_ATTR_FIND_MASK_DEFAULT set.
But it was getting overwritten by ib_cache_gid_set_default_gid() later
on as part of add_cmd().
Therefore, mac address change used to work for default GID.
With refactor series [1], this incorrect behavior is detected.
Therefore,
when deleting default GID, set default_gid and set MASK flag.
when deleting IP based GID, clear default_gid and set MASK flag.
[1] https://patchwork.kernel.org/patch/10319151/
Fixes: 238fdf48f2 ("IB/core: Add RoCE table bonding support")
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When IPv6 link local address is removed, if it matches with the default
GID, default GID(s)s gets removed which may not be a desired behavior.
This behavior is introduced by refactor work in Fixes tag.
When IPv6 link address is removed, removing its equivalent RoCEv2 GID
which exactly matches with default RoCEv2 GID, is right thing to do.
However achieving it correctly requires lot more changes, likely in
roce_gid_mgmt.c and core/cache.c. This should be done as independent
patch.
Therefore, this patch preserves behavior of not deleteing default GIDs.
This is done by providing explicit hint to consider default GID property
using mask and default_gid; similar to add_gid().
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Default GIDs are marked reserved at the start of the GID table at index
0 and 1 by gid_table_reserve_default(). Currently when default GID is
requested, it can still allocates an empty slot which was not marked as
RESERVED for default GID, which is incorrect.
At least in current code flow of roce_gid_mgmt.c, in theory we can
still request to allocate more than one/two default GIDs depending
on how upper devices are setup.
Therefore, it is better for cache layer to only allow our reserved slots
to be used by default GID allocation requests.
Fixes: 598ff6bae6 ("IB/core: Refactor GID modify code for RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Running bpf programs requires disabled preemption,
however at least some* of the BPF_PROG_RUN_ARRAY users
do not follow this rule.
To fix this bug, and also to make it not happen in the future,
let's add explicit preemption disabling/re-enabling
to the __BPF_PROG_RUN_ARRAY code.
* for example:
[ 17.624472] RIP: 0010:__cgroup_bpf_run_filter_sk+0x1c4/0x1d0
...
[ 17.640890] inet6_create+0x3eb/0x520
[ 17.641405] __sock_create+0x242/0x340
[ 17.641939] __sys_socket+0x57/0xe0
[ 17.642370] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 17.642944] SyS_socket+0xa/0x10
[ 17.643357] do_syscall_64+0x79/0x220
[ 17.643879] entry_SYSCALL_64_after_hwframe+0x42/0xb7
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix SIP conntrack with phones sending session descriptions for different
media types but same port numbers, from Florian Westphal.
2) Fix incorrect rtnl_lock mutex logic from IPVS sync thread, from Julian
Anastasov.
3) Skip compat array allocation in ebtables if there is no entries, also
from Florian.
4) Do not lose left/right bits when shifting marks from xt_connmark, from
Jack Ma.
5) Silence false positive memleak in conntrack extensions, from Cong Wang.
6) Fix CONFIG_NF_REJECT_IPV6=m link problems, from Arnd Bergmann.
7) Cannot kfree rule that is already in list in nf_tables, switch order
so this error handling is not required, from Florian Westphal.
8) Release set name in error path, from Florian.
9) include kmemleak.h in nf_conntrack_extend.c, from Stepheh Rothwell.
10) NAT chain and extensions depend on NF_TABLES.
11) Out of bound access when renaming chains, from Taehee Yoo.
12) Incorrect casting in xt_connmark leads to wrong bitshifting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[ 7.956247]
[ 7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[ 7.973239] pgd = eebfc000
[ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.
This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.
Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.
Fixes: 0cf1725676 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch initialize stack variables which are used in
frag_lowpan_compare_key to zero. In my case there are padding bytes in the
structures ieee802154_addr as well in frag_lowpan_compare_key. Otherwise
the key variable contains random bytes. The result is that a compare of
two keys by memcmp works incorrect.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reported-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
We already allocated the device and platform data at this
point. Instead of simply return from the probe function we
need to cleanup the resources first.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Xue Liu <liuxuenetmail@gmail.com>
atusb_probe() is never called in atomic context.
This function is only set as ".probe" in struct usb_driver.
Despite never getting called from atomic context,
atusb_probe() calls usb_alloc_urb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
We're missing a sentinel entry in kpti_safe_list. Thus is_midr_in_range_list()
can walk past the end of kpti_safe_list. Depending on the contents of memory,
this could erroneously match a CPU's MIDR, cause a data abort, or other bad
outcomes.
Add the sentinel entry to avoid this.
Fixes: be5b299830 ("arm64: capabilities: Add support for checks based on a list of MIDRs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
KMSAN reported use of uninit-value that I tracked to lack
of proper size check on RTA_TABLE attribute.
I also believe RTA_PREFSRC lacks a similar check.
Fixes: 86872cb579 ("[IPv6] route: FIB6 configuration using struct fib6_config")
Fixes: c3968a857a ("ipv6: RTA_PREFSRC support for ipv6 route source address selection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 8a8efa22f5 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.
However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.
One way to reproduce it:
# modprobe bonding
# brctl addbr br0
# brctl addif br0 eth1
# ifconfig bond0 192.168.122.1/24 up
# ifenslave bond0 eth2
# systemctl restart netconsole
# ifenslave bond0 br0
# ifconfig eth2 down
# systemctl restart netconsole
The netpoll won't really work.
This patch is to remove that slave_dev npinfo setting in bond_enslave().
Fixes: 8a8efa22f5 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on discussion with Kate Stewart this license is not a
BSD-2-Clause, but is now formally identified as Linux-OpenIB
by SPDX.
The key difference between the licenses is in the 'warranty'
paragraph.
if_infiniband.h refers to the 'OpenIB.org' license, but
does not include the text, instead it links to an obsolete
web site that contains a license that matches the BSD-2-Clause
SPX. There is no 'three clause' version of the OpenIB.org
license.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Command 'perf record' calls:
cmd_report()
record__auxtrace_init()
auxtrace_record__init()
On s390 function auxtrace_record__init() returns random return value due
to missing initialization.
This sometime causes 'perf record' to exit immediately without error
message and creating a perf.data file.
Fix this by setting error the return code to zero before returning from
platform specific functions which may not set the error code in call
cases.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180423142940.21143-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The RDMA CM will select a source device and address by consulting
the routing table if no source address is passed into
rdma_resolve_address(). Userspace will ask for this by passing an
all-zero source address in the RESOLVE_IP command. Unfortunately
the new check for non-zero address size rejects this with EINVAL,
which breaks valid userspace applications.
Fix this by explicitly allowing a zero address family for the source.
Fixes: 2975d5de64 ("RDMA/ucma: Check AF family prior resolving address")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Several options were incorrectly described, some lacked describing
required arguments while others were simply not documented, fix it.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1524382146-19609-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
.. and other related fields that do not need to be enabled
for events that have sampling leader.
It fixes the perf top usage Ingo reported broken:
# perf top -e '{cycles,msr/aperf/}:S'
The 'msr/aperf/' event is configured for write_back sampling, which is
not allowed by the MSR PMU, so it fails to create the event.
Adjusting related attr test.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-6-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The recent code refactoring made the argument for some helper
functions to be the explicit UAC_CS_* and UAC2_CS_* value instead of
0-based offset. However, there was one place left forgotten, and it
caused a regression on some devices appearing as the inconsistent
mixer setup.
This patch corrects the forgotten conversion.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199449
Fixes: 21e9b3e931 ("ALSA: usb-audio: fix uac control query argument")
Tested-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is one place missing __user annotation to the pointer used by
the recent code refactoring. Reported by sparse.
Fixes: 450296f305 ("ALSA: control: code refactoring TLV ioctl handler")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently all the event parsing fails end up in the event_pmu rule, and
display misleading help like:
$ perf stat -e inst kill
event syntax error: 'inst'
\___ Cannot find PMU `inst'. Missing kernel support?
...
The reason is that the event_pmu is too strong and match also single
string. Changing it to force the '/' separators to be part of the rule,
and getting the proper error now:
$ perf stat -e inst kill
event syntax error: 'inst'
\___ parser error
Run 'perf list' for a list of valid events
...
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-5-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 'perf stat' fallback for EACCES error sets the exclude_kernel
perf_event_attr and tries perf_event_open() again with it. In addition,
it also changes the name of the event to reflect that change by adding
the 'u' modifier.
But it does not take into account the '/' separator, so the event name
can end up mangled, like: (note the '/:' characters)
$ perf stat -e cpu/cpu-cycles/ kill
...
386,832 cpu/cpu-cycles/:u
Adding the code to check on the '/' separator and set the following
correct event name:
$ perf stat -e cpu/cpu-cycles/ kill
...
388,548 cpu/cpu-cycles/u
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-4-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf test case 58 (record+probe_libc_inet_pton.sh) executed on s390x
using kernel 4.16.0rc3 displays this result:
# perf trace --no-syscalls -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
probe_libc:inet_pton: (3ffa0240448)
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
After I installed kernel 4.16.0 the same tests uses commands:
# perf record -e probe_libc:inet_pton/call-graph=dwarf/
-o /tmp/perf.data.abc ping -6 -c 1 ::1
# perf script -i /tmp/perf.data.abc
and displays:
ping 39048 [006] 84230.381198: probe_libc:inet_pton: (3ffa0240448)
140448 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fbde1 gaih_inet (inlined)
fe2b9 __GI_getaddrinfo (inlined)
398d main (/usr/bin/ping)
Nothing else changed including glibc elfutils and other libraries picked
up by the build.
The entries for __libc_start_main and _start are missing.
I bisected missing __libc_start_main and _start to commit
Fixes: 3d20c62466 ("perf unwind: Unwind with libdw doesn't take symfs into account")
When I undo this commit I get this call stack on s390:
[root@s35lp76 perf]# ./perf script -i /tmp/perf.data.abc
ping 39048 [006] 84230.381198: probe_libc:inet_pton: (3ffa0240448)
140448 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fbde1 gaih_inet (inlined)
fe2b9 __GI_getaddrinfo (inlined)
398d main (/usr/bin/ping)
22fbd __libc_start_main (/usr/lib64/libc-2.26.so)
457b _start (/usr/bin/ping)
Looks like dwarf functions dwfl_xxx create different call back stack
trace when using file /usr/lib/debug/usr/bin/ping-20161105-7.fc27.s390x.debug
instead of file /usr/bin/ping.
Fix this test case on s390 and do not expect any call back stack entry
after the main() function. Also be more robust and accept a leading
__GI_ prefix in front of getaddrinfo.
On x86 this test case shows the same call stack using both kernel
versions 4.16.0rc3 and 4.16.0 and also stops at main:
[root@f27 perf]# ./perf script -i /tmp/perf.data.tmr
ping 4446 [000] 172.027088: probe_libc:inet_pton: (7fdfa08c93c0)
1393c0 __GI___inet_pton (/usr/lib64/libc-2.26.so)
fe60d getaddrinfo (/usr/lib64/libc-2.26.so)
2f40 main (/usr/bin/ping)
[root@f27 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Martin Vuille <jpmv27@aim.com>
Link: http://lkml.kernel.org/r/20180423082428.7930-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the type field in pmu-events/arch/s390/mapfile.cvs more generic to
match the created cpuid string for s390.
The pattern also checks for the counter first version number and counter
second version number ([13]\.[1-5]) and the authorization field which
follows.
These numbers do not exist in the cpuid identification string when perf
commands are executed on a z/VM environment (which does not support CPU
counter measurement facility).
CPUID string for LPAR:
cpuid : IBM,3906,704,M03,3.5,002f
CPUID string for z/VM:
cpuid : IBM,2964,702,N96
This allows the removal of s390 specific cpuid compare code and uses the
common compare function with its regular expression matching algorithm.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180423081745.3672-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since commit 39cee200c2 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).
Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.
Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the new HCD flag which prevents USB core from trying to manage our
phys.
This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).
Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e2796 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fe014d4e6b (staging: wilc1000: free memory allocated for general info
message from firmware) introduced a bug by using wrong source address in
kmemdup(). 'conn_info.req_ies' is used for source address in kempdup()
instead of 'hif_drv->usr_conn_req.ies'.
This commit fixes the NULL pointer dereference issue in
host_int_parse_assoc_resp_info() by using the correct source address in
kmemdup().
Fixes: fe014d4e6b (staging: wilc1000: free memory allocated for general info message from firmware)
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
map_groups__fixup_end() was called to set the end addresses of kernel
and module maps. But now since machine__create_modules() sets the end
address of modules properly, the only remaining piece is the kernel map.
We can set it with adjacent module's address directly instead of calling
map_groups__fixup_end(). If there's no module after the kernel map, the
end address will be ~0ULL.
Since it also changes the start address of the kernel map, it needs to
re-insert the map to the kmaps in order to keep a correct ordering. Kim
reported that it caused problems on ARM64.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@lge.com
Link: http://lkml.kernel.org/r/20180419235915.GA19067@sejong
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
