Fixes "no previous prototype" warnings.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once mst topology is constructed, later on new connected monitors
are reported to source by CSN message. Within CSN, there is no
carried info of DPCD_REV comparing to LINK_ADDRESS reply. As the
result, we might leave some ports connected to DP but without DPCD
revision number which will affect us determining the capability of
the DP Rx.
[How]
Send out remote DPCD read when the port's dpcd_rev is 0x0 in
detect_ctx(). Firstly, read out the value from DPCD 0x2200. If the
return value is 0x0, it's likely the DP1.2 DP Rx then we reques
revision from DPCD 0x0 again.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The existing calculations in DCN3.1 were placeholder and need to be
replaced with HW team approved calculations.
[How]
The new calculations add new parameters to the bounding box and pipe
params - VblankNom and the bounding box default.
The placeholder calculations are dropped from DCN3.1 in the meantime
while we work out hardware approved replacements.
Also fix a bug where we wipe out other register contents with a REG_SET
instead of a REG_UPDATE for the register we were programming the
min_dst_y_next_start_optimized.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For additional power savings, PSR SU (also referred to as PSR2) can be
enabled on eDP panels with PSR SU support.
PSR2 saves more power compared to PSR1 by allowing more opportunities
for the display hardware to be shut down. In comparison to PSR1, Shut
down can now occur in-between frames, as well as in display regions
where there is no visible update. In otherwords, it allows for some
display hw components to be enabled only for a **selectively updated**
region of the visible display. Hence PSR SU.
[HOW]
To define the SU region, support from the OS is required. OS needs to
inform driver of damaged regions that need to be flushed to the eDP
panel. Today, such support is lacking in most compositors.
Therefore, an in-between solution is to implement PSR SU for MPO and
cursor scenarios. The plane bounds can be used to define the damaged
region to be flushed to panel. This is achieved by:
* Leveraging dm_crtc_state->mpo_requested flag to identify when MPO is
enabled.
* If MPO is enabled, only add updated plane bounds to dirty region.
Determine plane update by either:
* Existence of drm damaged clips attached to the plane (added by a
damage-aware compositor)
* Change in fb id (flip)
* Change in plane bounds (position and dimensions)
* If cursor is enabled, the old_pos and new_pos of cursor plus cursor
size is used as damaged regions(*).
(*) Cursor updates follow a different code path through DC. PSR SU for
cursor is already implemented in DC, and the only thing required to
enable is to set DC_PSR_VERSION_SU_1 on the eDP link. See
dcn10_dmub_update_cursor_data().
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To involve the cursor position into dirty rectangle calculation.
[how]
- separate plane and cursor update by different DMUB command
- send the cursor information while cursor updating, when updating
cursor position/attribute, store cursor pos/attr to hubp, and
notify dmub FW to exit psr before program cursor registers
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently the psr configuration parameters are hardcoded before
feeding into the DC helper before passing to DMUB FW. We'd rework
to call a shared helper to calculate/update generic psr config
fields which are relying on the stream timing and eDP sink PSR
caps to avoid hard-coding.
[how]
- drop part of hard-coded psr config fields by replacing w/ the
call of helper from DM before feeding into DC link setup psr
helper
- For those DM specific psr config fields, e.g. allow smu opt, is
not to be set/updated from the shared helper but to rely on the
DC feature mask
- for the psr version field in psr_config structure, since only
the field psr_version of DC link psr_settings matters for that
fed to DMUB FW, thus no need to set/update the psr_version field
of psr_config structure.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently the amdgpu DM psr configuration parameters are hardcoded
before feeding into the DC helper to setup PSR. We would define a
helper which is to calculate parts of the psr config fields to
avoid hard-coding.
[how]
To make helper shareable, declare and define the helper in the
module_helper, to set/update below fields:
- psr remote buffer setup time
- sdp tx line number deadline
- line time in us
- su_y_granularity
- su_granularity_required
- psr_frame_capture_indication_req
- psr_exit_link_training_required
add another helper to check given the stream context, if there is
only one stream and the output is eDP panel connected.
changes in v2:
------------------
- add detailed comment for how psr setup time is calculated as per
eDP 1.5 spec
Cc: Chandan Vurdigerenataraj <chandan.vurdigerenataraj@amd.com>
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some specific TCON chip has HW limitation to support PSRSU+DSC.
[how]
Force ffu mode when DSC enabled if we detect it is the specific
model from sink OUI DPCD. And disable ABM update for this case.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and DMUB fw for PSR-SU
[how]
return True if PSR-SU in the checker should_use_dmub_lock()
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
While support ALPM, do ALPM state transition while PSR entry/exit.
ALPM is needed for PSR-SU feature, and since the function is ready,
we'd enable it by default.
- Add psr level definition to enable/disable ALPM and set ALPM
powerdone mode.
- Enable ALPM by default
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DC driver send PSR exit dmub command to DMUB FW, it might not
wait until PSR exit. Then it may hit the following deadlock situation.
1. DC driver send HW LOCK command to DMUB FW due to frame update
2. DMUB FW Set the HW lock
3. DMUB execute PSR exit sequence and stuck at polling DPG Pending
register due to the HW Lock is set
4. DC driver ask DMUB FW to unlock HW lock, but DMUB FW is polling
DPG pending register
[how]
The reason why DC driver doesn't wait until PSR exit is because some of
the PSR state machine state is not update the dc driver. So when DC
driver read back the PSR state, it take the state for PSR inactive.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current PSR SU programming margin is fixed base on FHD 60HZ
panel. If the resolution and refresh rate become higher, the time
of current margin might not cover the programming SU time.
[how]
Notice that the programming SU time is the same among different
panels.
Instead of fixing the margin with target line number, change the
margin unit to micro second which indicate the time needed for
programming SU. Then FW set the margin line number base on the
line time and margin time.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & how]
We only support line capture indication as 0 for PSRSU
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The Y-granularity panel parameter indicate the grid
pattern granularity in the Y direction for PSRSU.
[How]
Send the Y-granularity data by PSR_COPY_SETTINGS dmub command.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable pipe1 support starting from SIENNA CICHLID asic
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting from SIENNA CICHLID asic supports two gfx pipes, enabling
two graphics queues, 1 on each pipe, pipe0 queue0 would be the normal
piority queue and pipe1 queue0 would be the high priority queue
Only one queue per pipe is visble to SPI, SPI looks at the priority
value assigned to CP_GFX_HQD_QUEUE_PRIORITY from each of the queue's
HQD/MQD.
Create contexts applying AMDGPU_CTX_PRIORITY_HIGH which submits job
to the high priority queue on GFX pipe1. There would be starvation
of LP workload if HP workload is always available.
v2:
- remove unnecessary check(Nirmoy)
- make pipe1 hardware support a separate patch(Nirmoy)
- remove duplicate code(Shashank)
- add CSA support for second gfx pipe(Alex)
v3(Christian):
- fix incorrect indentation
- merge COMPUTE and GFX switch cases as both calls the same function.
v4:
- rebase w/ latest code base
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allocate memory for register value and use the same values for devcoredump.
v1 -> v2: Change krealloc_array() to kmalloc_array()
v2 -> v3: Fix alignment
Signed-off-by: Somalapuram Amaranath <Amaranath.Somalapuram@amd.com>
Reviewed-by: Shashank Sharma <Shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support PSR2 Source DPCD configuration
[How]
Update the PSR2 Source DPCD settings while the PSR2 enabled
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
We need to implement the VSC packet rev4 that is required by PSRSU.
Follow the eDP 1.5 spec pg. 257
changes in v2:
-------------------
- set vsc packet rev2 for PSR1
Cc: Chandan Vurdigerenataraj <chandan.vurdigerenataraj@amd.com>
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Based on PSRSU specification, every selective update frame need to use
two SDP to indicate the frame active range. So we occupy another GSP1
for PSRSU execution.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In PSR-SU design, the DMUB FW handles the combination of multiple
dirty rectangles.
[how]
- create DC dmub update dirty rectangle helper which sends the
dirty rectangles per pipe from DC to DMUB, and DMUB FW will
handle to combine the dirty RECTs
- call the helper from DC commit plane update function.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
set psr version as PSR-SU in kernel-FW interface function to ensure
the correct dmub command parameter is fed into FW.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If user requests for NFT_CHAIN_HW_OFFLOAD, then check if either device
provides the .ndo_setup_tc interface or there is an indirect flow block
that has been registered. Otherwise, bail out early from the preparation
phase. Moreover, validate that family == NFPROTO_NETDEV and hook is
NF_NETDEV_INGRESS.
Fixes: c9626a2cbd ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The three commits:
36fd2a65bc ("dt-bindings: display: convert Arm HDLCD to DT schema")
0f6983509e ("dt-bindings: display: convert Arm Komeda to DT schema")
2c8b082a3a ("dt-bindings: display: convert Arm Mali-DP to DT schema")
convert the arm display dt-bindings, arm,*.txt to arm,*.yaml, but miss to
adjust its reference in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about
broken references.
Repair these file references in ARM HDLCD DRM DRIVER, ARM KOMEDA DRM-KMS
DRIVER and ARM MALI-DP DRM DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220601041746.22986-1-lukas.bulwahn@gmail.com
There is a limitation in TI DP83867 PHY device where SGMII AN is only
triggered once after the device is booted up. Even after the PHY TPI is
down and up again, SGMII AN is not triggered and hence no new in-band
message from PHY to MAC side SGMII.
This could cause an issue during power up, when PHY is up prior to MAC.
At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t
receive new in-band message from TI PHY with correct link status, speed
and duplex info.
As suggested by TI, implemented a SW solution here to retrigger SGMII
Auto-Neg whenever there is a link change.
v2: Add Fixes tag in commit message.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Focusrite Saffire 6 has fixed audioformat quirks with multiple
endpoints assigned to a single altsetting. Unfortunately the generic
parser couldn't detect the sync endpoint correctly as the implicit
sync due to the missing EP attribute bits. In the former kernels, it
used to work somehow casually, but it's been broken for a while after
the large code change in 5.11.
This patch cures the regression by the following:
- Allow the static quirk table to provide the sync EP information;
we just need to fill the fields and let the generic parser skipping
parsing if sync_ep is already set.
- Add the sync endpoint information to the entry for Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When ep_idx is already non-zero, it means usually a capture stream
that is set up explicity by a fixed-format quirk, and applying the
check for generic (non-implicit-fb) sync EPs might hit incorrectly,
resulting in a bogus sync endpoint for the capture stream.
This patch adds a check for the ep_idx and skip if it's a secondary
endpoint. It's a part of the fixes for regressions on Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we're about to send the first layoutget for an empty layout, we want
to make sure that we drain out the existing pending layoutget calls
first. The reason is that these layouts may have been already implicitly
returned to the server by a recall to which the client gave a
NFS4ERR_NOMATCHING_LAYOUT response.
The problem is that wait_var_event_killable() could in principle see the
plh_outstanding count go back to '1' when the first process to wake up
starts sending a new layoutget. If it fails to get a layout, then this
loop can continue ad infinitum...
Fixes: 0b77f97a7e ("NFSv4/pnfs: Fix layoutget behaviour after invalidation")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the server tells us that a pNFS layout is not available for a
specific file, then we should not keep pounding it with further
layoutget requests.
Fixes: 183d9e7b11 ("pnfs: rework LAYOUTGET retry handling")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Abort path release flow rule object, however, commit path does not.
Update code to destroy these objects before releasing the transaction.
Fixes: c9626a2cbd ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Release the list of new hooks that are pending to be registered in case
that unsupported flowtable flags are provided.
Fixes: 78d9f48f7f ("netfilter: nf_tables: add devices to existing flowtable")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While using SCMI iterators helpers a few local automatic variables are
defined but then used only as input for sizeof operators.
cppcheck is fooled to complain about this with:
| drivers/firmware/arm_scmi/sensors.c:341:48: warning: Variable 'msg' is
| not assigned a value. [unassignedVariable]
| struct scmi_msg_sensor_list_update_intervals *msg;
Even though this is an innocuos warning, since the uninitialized variable
is at the end never used in the reported cases, fix these occurences all
over SCMI stack to avoid keeping unneeded objects on the stack.
Link: https://lore.kernel.org/r/20220530115237.277077-1-cristian.marussi@arm.com
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Even though malformed replies from firmware must be treated carefully to
avoid memory corruption in the kernel, some out-of-spec SCMI replies can
be tolerated to avoid breaking existing deployed system, as long as they
won't cause memory issues.
Relax the sanity checks on the recieved protocol list in the base protocol
to avoid breaking one of the deployed platform whose firmware is not easily
upgradable currently.
Link: https://lore.kernel.org/r/20220523171559.472112-1-cristian.marussi@arm.com
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Upstream commit 9f73f1aef9 ("btrfs: force v2 space cache usage for
subpage mount") forces subpage mount to use v2 cache, to avoid
deprecated v1 cache which doesn't support subpage properly.
But there is a loophole that user can still remount to v1 cache.
The existing check will only give users a warning, but does not really
prevent to do the remount.
Although remounting to v1 will not cause any problems since the v1 cache
will always be marked invalid when mounted with a different page size,
it's still better to prevent v1 cache at all for subpage mounts.
Fixes: 9f73f1aef9 ("btrfs: force v2 space cache usage for subpage mount")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we start an unmount, at close_ctree(), if we have the reclaim task
running and in the middle of a data block group relocation, we can trigger
a deadlock when stopping an async reclaim task, producing a trace like the
following:
[629724.498185] task:kworker/u16:7 state:D stack: 0 pid:681170 ppid: 2 flags:0x00004000
[629724.499760] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
[629724.501267] Call Trace:
[629724.501759] <TASK>
[629724.502174] __schedule+0x3cb/0xed0
[629724.502842] schedule+0x4e/0xb0
[629724.503447] btrfs_wait_on_delayed_iputs+0x7c/0xc0 [btrfs]
[629724.504534] ? prepare_to_wait_exclusive+0xc0/0xc0
[629724.505442] flush_space+0x423/0x630 [btrfs]
[629724.506296] ? rcu_read_unlock_trace_special+0x20/0x50
[629724.507259] ? lock_release+0x220/0x4a0
[629724.507932] ? btrfs_get_alloc_profile+0xb3/0x290 [btrfs]
[629724.508940] ? do_raw_spin_unlock+0x4b/0xa0
[629724.509688] btrfs_async_reclaim_metadata_space+0x139/0x320 [btrfs]
[629724.510922] process_one_work+0x252/0x5a0
[629724.511694] ? process_one_work+0x5a0/0x5a0
[629724.512508] worker_thread+0x52/0x3b0
[629724.513220] ? process_one_work+0x5a0/0x5a0
[629724.514021] kthread+0xf2/0x120
[629724.514627] ? kthread_complete_and_exit+0x20/0x20
[629724.515526] ret_from_fork+0x22/0x30
[629724.516236] </TASK>
[629724.516694] task:umount state:D stack: 0 pid:719055 ppid:695412 flags:0x00004000
[629724.518269] Call Trace:
[629724.518746] <TASK>
[629724.519160] __schedule+0x3cb/0xed0
[629724.519835] schedule+0x4e/0xb0
[629724.520467] schedule_timeout+0xed/0x130
[629724.521221] ? lock_release+0x220/0x4a0
[629724.521946] ? lock_acquired+0x19c/0x420
[629724.522662] ? trace_hardirqs_on+0x1b/0xe0
[629724.523411] __wait_for_common+0xaf/0x1f0
[629724.524189] ? usleep_range_state+0xb0/0xb0
[629724.524997] __flush_work+0x26d/0x530
[629724.525698] ? flush_workqueue_prep_pwqs+0x140/0x140
[629724.526580] ? lock_acquire+0x1a0/0x310
[629724.527324] __cancel_work_timer+0x137/0x1c0
[629724.528190] close_ctree+0xfd/0x531 [btrfs]
[629724.529000] ? evict_inodes+0x166/0x1c0
[629724.529510] generic_shutdown_super+0x74/0x120
[629724.530103] kill_anon_super+0x14/0x30
[629724.530611] btrfs_kill_super+0x12/0x20 [btrfs]
[629724.531246] deactivate_locked_super+0x31/0xa0
[629724.531817] cleanup_mnt+0x147/0x1c0
[629724.532319] task_work_run+0x5c/0xa0
[629724.532984] exit_to_user_mode_prepare+0x1a6/0x1b0
[629724.533598] syscall_exit_to_user_mode+0x16/0x40
[629724.534200] do_syscall_64+0x48/0x90
[629724.534667] entry_SYSCALL_64_after_hwframe+0x44/0xae
[629724.535318] RIP: 0033:0x7fa2b90437a7
[629724.535804] RSP: 002b:00007ffe0b7e4458 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[629724.536912] RAX: 0000000000000000 RBX: 00007fa2b9182264 RCX: 00007fa2b90437a7
[629724.538156] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000555d6cf20dd0
[629724.539053] RBP: 0000555d6cf20ba0 R08: 0000000000000000 R09: 00007ffe0b7e3200
[629724.539956] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[629724.540883] R13: 0000555d6cf20dd0 R14: 0000555d6cf20cb0 R15: 0000000000000000
[629724.541796] </TASK>
This happens because:
1) Before entering close_ctree() we have the async block group reclaim
task running and relocating a data block group;
2) There's an async metadata (or data) space reclaim task running;
3) We enter close_ctree() and park the cleaner kthread;
4) The async space reclaim task is at flush_space() and runs all the
existing delayed iputs;
5) Before the async space reclaim task calls
btrfs_wait_on_delayed_iputs(), the block group reclaim task which is
doing the data block group relocation, creates a delayed iput at
replace_file_extents() (called when COWing leaves that have file extent
items pointing to relocated data extents, during the merging phase
of relocation roots);
6) The async reclaim space reclaim task blocks at
btrfs_wait_on_delayed_iputs(), since we have a new delayed iput;
7) The task at close_ctree() then calls cancel_work_sync() to stop the
async space reclaim task, but it blocks since that task is waiting for
the delayed iput to be run;
8) The delayed iput is never run because the cleaner kthread is parked,
and no one else runs delayed iputs, resulting in a hang.
So fix this by stopping the async block group reclaim task before we
park the cleaner kthread.
Fixes: 18bb8bbf13 ("btrfs: zoned: automatically reclaim zones")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
By assigning xen-grant DMA ops we will restrict memory access for
passed device using Xen grant mappings. This is needed for using any
virtualized device (e.g. virtio) in Xen guests in a safe manner.
Please note, for the virtio devices the XEN_VIRTIO config should
be enabled (it forces ARCH_HAS_RESTRICTED_VIRTIO_MEMORY_ACCESS).
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/1654197833-25362-9-git-send-email-olekstysh@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Use the presence of "iommus" property pointed to the IOMMU node with
recently introduced "xen,grant-dma" compatible as a clear indicator
of enabling Xen grant mappings scheme for that device and read the ID
of Xen domain where the corresponding backend is running. The domid
(domain ID) is used as an argument to the Xen grant mapping APIs.
To avoid the deferred probe timeout which takes place after reusing
generic IOMMU device tree bindings (because the IOMMU device never
becomes available) enable recently introduced stub IOMMU driver by
selecting XEN_GRANT_DMA_IOMMU.
Also introduce xen_is_grant_dma_device() to check whether xen-grant
DMA ops need to be set for a passed device.
Remove the hardcoded domid 0 in xen_grant_setup_dma_ops().
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/1654197833-25362-8-git-send-email-olekstysh@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
In order to reuse generic IOMMU device tree bindings by Xen grant
DMA-mapping layer we need to add this stub driver from a fw_devlink
perspective (grant-dma-ops cannot be converted into the proper
IOMMU driver).
Otherwise, just reusing IOMMU bindings (without having a corresponding
driver) leads to the deferred probe timeout afterwards, because
the IOMMU device never becomes available.
This stub driver does nothing except registering empty iommu_ops,
the upper layer "of_iommu" will treat this as NO_IOMMU condition
and won't return -EPROBE_DEFER.
As this driver is quite different from the most hardware IOMMU
implementations and only needed in Xen guests, place it in drivers/xen
directory. The subsequent commit will make use of it.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/1654197833-25362-7-git-send-email-olekstysh@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
The main purpose of this binding is to communicate Xen specific
information using generic IOMMU device tree bindings (which is
a good fit here) rather than introducing a custom property.
Introduce Xen specific IOMMU for the virtualized device (e.g. virtio)
to be used by Xen grant DMA-mapping layer in the subsequent commit.
The reference to Xen specific IOMMU node using "iommus" property
indicates that Xen grant mappings need to be enabled for the device,
and it specifies the ID of the domain where the corresponding backend
resides. The domid (domain ID) is used as an argument to the Xen grant
mapping APIs.
This is needed for the option to restrict memory access using Xen grant
mappings to work which primary goal is to enable using virtio devices
in Xen guests.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1654197833-25362-6-git-send-email-olekstysh@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
