When a group of messages are sent from user space as a set, if
the last message has less than Tx FIFO DEPTH number of bytes
to transfer, Tx half empty interrupt is triggered continuously
from the hardware. It is due to Bus not busy interrupt coming
along with Tx half empty and tx empty.
Hence, service the Tx interrupts before Bus not busy interrupt
to update the i2c message status correctly.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most of these stuff are reported by checkpatch.
But fixes are:
- Incorrect indetation
- Missing blank line after variable declaration
- Additional ()
- Missing spaces around +
- Missing parenthesis when if has them
- Newlines
- Remove MODULE_ALIAS - none is really using it
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Check the return value of xiic_reinit.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Return irq instead of ret which always equals to zero here.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's more logical to read these get timing parameters ACPI method calls
sorted by speed categories in increasing order: Standard-mode,
Fast-mode, Fast-mode Plus and High-speed mode.
Originally these were in order after commit a92ec1746f
("i2c: designware: get fast plus and high speed *CNT configuration") but
got mixed up over the years.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8 ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The rk3568 cru requires a clock input and a phandle to the grf node. Add
these bindings to clear some dtbs_check warnings.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220511150117.113070-2-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When ADQ queue groups (TCs) are created via tc mqprio command,
RSS contexts and associated RSS indirection tables are configured
automatically per TC based on the queue ranges specified for
each traffic class.
For ex:
tc qdisc add dev enp175s0f0 root mqprio num_tc 3 map 0 1 2 \
queues 2@0 8@2 4@10 hw 1 mode channel
will create 3 queue groups (TC 0-2) with queue ranges 2, 8 and 4
in 3 queue groups. Each queue group is associated with its
own RSS context and RSS indirection table.
Add support to expose RSS indirection tables for all ADQ queue
groups using ethtool RSS contexts interface.
ethtool -x enp175s0f0 context <tc-num>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220512213249.3747424-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the capability to map non-linear xdp frames in XDP_TX and ndo_xdp_xmit
callback.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220512212621.3746140-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau says:
====================
mptcp: Subflow accounting fix
This series contains a bug fix affecting the in-kernel path manager
(patch 1), where closing subflows would sometimes not adjust the PM's
count of active subflows. Patch 2 updates the selftests to exercise the
new code.
====================
Link: https://lore.kernel.org/r/20220512232642.541301-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add and delete a bunch of endpoints and verify the
respect of configured limits.
This covers the codepath introduced by the previous patch.
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the PM closes a fully established MPJ subflow or the subflow
creation errors out in it's early stage the subflows counter is
not bumped accordingly.
This change adds the missing accounting, additionally taking care
of updating accordingly the 'accept_subflow' flag.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove napi_weight statics which are set to 64 and never modified,
remnants of the out-of-tree napi_weight module param.
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220512205603.1536771-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
protected_* files have 600 permissions which prevents non-superuser from
reading them.
Container like "AWS greengrass" refuse to launch unless
protected_hardlinks and protected_symlinks are set. When containers like
these run with "userns-remap" or "--user" mapping container's root to
non-superuser on host, they fail to run due to denied read access to these
files.
As these protections are hardly a secret, and do not possess any security
risk, making them world readable.
Though above greengrass usecase needs read access to only
protected_hardlinks and protected_symlinks files, setting all other
protected_* files to 644 to keep consistency.
Link: http://lkml.kernel.org/r/20200709235115.56954-1-jpitti@cisco.com
Fixes: 800179c9b8 ("fs: add link restrictions")
Signed-off-by: Julius Hemanth Pitti <jpitti@cisco.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
At present, pages not in the target zone are added to cc->migratepages
list in isolate_migratepages_block(). As a result, pages may migrate
between nodes unintentionally.
This would be a serious problem for older kernels without commit
a984226f45 ("mm: memcontrol: remove the pgdata parameter of
mem_cgroup_page_lruvec"), because it can corrupt the lru list by
handling pages in list without holding proper lru_lock.
Avoid returning a pfn outside the target zone in the case that it is
not aligned with a pageblock boundary. Otherwise
isolate_migratepages_block() will handle pages not in the target zone.
Link: https://lkml.kernel.org/r/20220511044300.4069-1-yamamoto.rei@jp.fujitsu.com
Fixes: 70b44595ea ("mm, compaction: use free lists to quickly locate a migration source")
Signed-off-by: Rei Yamamoto <yamamoto.rei@jp.fujitsu.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Wonhyuk Yang <vvghjk1234@gmail.com>
Cc: Rei Yamamoto <yamamoto.rei@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix the warning - "Enum value 'NR_DAMON_OPS' not described in enum
'damon_ops_id'" generated by the command "make pdfdocs"
Link: https://lkml.kernel.org/r/20220508073316.141401-1-gautammenghani201@gmail.com
Signed-off-by: Gautam Menghani <gautammenghani201@gmail.com>
Reviewed-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We run a lot of automated tests when building our software and run into
OOM scenarios when the tests run unbounded. v1 memcg exports
memcg->watermark as "memory.max_usage_in_bytes" in sysfs. We use this
metric to heuristically limit the number of tests that can run in parallel
based on per test historical data.
This metric is currently not exported for v2 memcg and there is no other
easy way of getting this information. getrusage() syscall returns
"ru_maxrss" which can be used as an approximation but that's the max RSS
of a single child process across all children instead of the aggregated
max for all child processes. The only work around is to periodically poll
"memory.current" but that's not practical for short-lived one-off cgroups.
Hence, expose memcg->watermark as "memory.peak" for v2 memcg.
Link: https://lkml.kernel.org/r/20220507050916.GA13577@us192.sjc.aristanetworks.com
Signed-off-by: Ganesan Rajagopal <rganesan@arista.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We must add hugetlb_free_vmemmap=on (or "off") to the boot cmdline and
reboot the server to enable or disable the feature of optimizing vmemmap
pages associated with HugeTLB pages. However, rebooting usually takes a
long time. So add a sysctl to enable or disable the feature at runtime
without rebooting. Why we need this? There are 3 use cases.
1) The feature of minimizing overhead of struct page associated with
each HugeTLB is disabled by default without passing
"hugetlb_free_vmemmap=on" to the boot cmdline. When we (ByteDance)
deliver the servers to the users who want to enable this feature, they
have to configure the grub (change boot cmdline) and reboot the
servers, whereas rebooting usually takes a long time (we have thousands
of servers). It's a very bad experience for the users. So we need a
approach to enable this feature after rebooting. This is a use case in
our practical environment.
2) Some use cases are that HugeTLB pages are allocated 'on the fly'
instead of being pulled from the HugeTLB pool, those workloads would be
affected with this feature enabled. Those workloads could be
identified by the characteristics of they never explicitly allocating
huge pages with 'nr_hugepages' but only set 'nr_overcommit_hugepages'
and then let the pages be allocated from the buddy allocator at fault
time. We can confirm it is a real use case from the commit
099730d674. For those workloads, the page fault time could be ~2x
slower than before. We suspect those users want to disable this
feature if the system has enabled this before and they don't think the
memory savings benefit is enough to make up for the performance drop.
3) If the workload which wants vmemmap pages to be optimized and the
workload which wants to set 'nr_overcommit_hugepages' and does not want
the extera overhead at fault time when the overcommitted pages be
allocated from the buddy allocator are deployed in the same server.
The user could enable this feature and set 'nr_hugepages' and
'nr_overcommit_hugepages', then disable the feature. In this case, the
overcommited HugeTLB pages will not encounter the extra overhead at
fault time.
Link: https://lkml.kernel.org/r/20220512041142.39501-5-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use kstrtobool rather than open coding "on" and "off" parsing in
mm/hugetlb_vmemmap.c, which is more powerful to handle all kinds of
parameters like 'Yy1Nn0' or [oO][NnFf] for "on" and "off".
Link: https://lkml.kernel.org/r/20220512041142.39501-4-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Optimizing HugeTLB vmemmap pages is not compatible with allocating memmap
on hot added memory. If "hugetlb_free_vmemmap=on" and
memory_hotplug.memmap_on_memory" are both passed on the kernel command
line, optimizing hugetlb pages takes precedence. However, the global
variable memmap_on_memory will still be set to 1, even though we will not
try to allocate memmap on hot added memory.
Also introduce mhp_memmap_on_memory() helper to move the definition of
"memmap_on_memory" to the scope of CONFIG_MHP_MEMMAP_ON_MEMORY. In the
next patch, mhp_memmap_on_memory() will also be exported to be used in
hugetlb_vmemmap.c.
Link: https://lkml.kernel.org/r/20220512041142.39501-3-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "add hugetlb_optimize_vmemmap sysctl", v11.
This series aims to add hugetlb_optimize_vmemmap sysctl to enable or
disable the feature of optimizing vmemmap pages associated with HugeTLB
pages.
This patch (of 4):
If the size of "struct page" is not the power of two but with the feature
of minimizing overhead of struct page associated with each HugeTLB is
enabled, then the vmemmap pages of HugeTLB will be corrupted after
remapping (panic is about to happen in theory). But this only exists when
!CONFIG_MEMCG && !CONFIG_SLUB on x86_64. However, it is not a
conventional configuration nowadays. So it is not a real word issue, just
the result of a code review.
But we cannot prevent anyone from configuring that combined configure.
This hugetlb_optimize_vmemmap should be disable in this case to fix this
issue.
Link: https://lkml.kernel.org/r/20220512041142.39501-1-songmuchun@bytedance.com
Link: https://lkml.kernel.org/r/20220512041142.39501-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb: 2M and
1G, but also CONT-PTE/PMD size: 64K and 32M if a 4K page size specified.
When unmapping a hugetlb page, we will get the relevant page table entry
by huge_pte_offset() only once to nuke it. This is correct for PMD or PUD
size hugetlb, since they always contain only one pmd entry or pud entry in
the page table.
However this is incorrect for CONT-PTE and CONT-PMD size hugetlb, since
they can contain several continuous pte or pmd entry with same page table
attributes, so we will nuke only one pte or pmd entry for this
CONT-PTE/PMD size hugetlb page.
And now try_to_unmap() is only passed a hugetlb page in the case where the
hugetlb page is poisoned. Which means now we will unmap only one pte
entry for a CONT-PTE or CONT-PMD size poisoned hugetlb page, and we can
still access other subpages of a CONT-PTE or CONT-PMD size poisoned
hugetlb page, which will cause serious issues possibly.
So we should change to use huge_ptep_clear_flush() to nuke the hugetlb
page table to fix this issue, which already considered CONT-PTE and
CONT-PMD size hugetlb.
We've already used set_huge_swap_pte_at() to set a poisoned swap entry for
a poisoned hugetlb page. Meanwhile adding a VM_BUG_ON() to make sure the
passed hugetlb page is poisoned in try_to_unmap().
Link: https://lkml.kernel.org/r/0a2e547238cad5bc153a85c3e9658cb9d55f9cac.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/730ea4b6d292f32fb10b7a4e87dad49b0eb30474.1652147571.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb: 2M and
1G, but also CONT-PTE/PMD size: 64K and 32M if a 4K page size specified.
When migrating a hugetlb page, we will get the relevant page table entry
by huge_pte_offset() only once to nuke it and remap it with a migration
pte entry. This is correct for PMD or PUD size hugetlb, since they always
contain only one pmd entry or pud entry in the page table.
However this is incorrect for CONT-PTE and CONT-PMD size hugetlb, since
they can contain several continuous pte or pmd entry with same page table
attributes. So we will nuke or remap only one pte or pmd entry for this
CONT-PTE/PMD size hugetlb page, which is not expected for hugetlb
migration. The problem is we can still continue to modify the subpages'
data of a hugetlb page during migrating a hugetlb page, which can cause a
serious data consistent issue, since we did not nuke the page table entry
and set a migration pte for the subpages of a hugetlb page.
To fix this issue, we should change to use huge_ptep_clear_flush() to nuke
a hugetlb page table, and remap it with set_huge_pte_at() and
set_huge_swap_pte_at() when migrating a hugetlb page, which already
considered the CONT-PTE or CONT-PMD size hugetlb.
[akpm@linux-foundation.org: fix nommu build]
[baolin.wang@linux.alibaba.com: fix build errors for !CONFIG_MMU]
Link: https://lkml.kernel.org/r/a4baca670aca637e7198d9ae4543b8873cb224dc.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/ea5abf529f0997b5430961012bfda6166c1efc8c.1652147571.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Fix CONT-PTE/PMD size hugetlb issue when unmapping or migrating", v4.
presently, migrating a hugetlb page or unmapping a poisoned hugetlb page,
we'll use ptep_clear_flush() and set_pte_at() to nuke the page table entry
and remap it, and this is incorrect for CONT-PTE or CONT-PMD size hugetlb
page, which will cause potential data consistent issue. This patch set
will change to use hugetlb related APIs to fix this issue.
Note: Mike pointed out the huge_ptep_get() will only return the one
specific value, and it would not take into account the dirty or young bits
of CONT-PTE/PMDs like the huge_ptep_get_and_clear() [1]. This
inconsistent issue is not introduced by this patch set, and this issue
will be addressed in another thread [2]. Meanwhile the uffd for hugetlb
case [3] pointed out by Gerald also needs another patch to address.
[1] https://lore.kernel.org/linux-mm/85bd80b4-b4fd-0d3f-a2e5-149559f2f387@oracle.com/
[2] https://lore.kernel.org/all/cover.1651998586.git.baolin.wang@linux.alibaba.com/
[3] https://lore.kernel.org/linux-mm/20220503120343.6264e126@thinkpad/
This patch (of 3):
It is incorrect to use ptep_clear_flush() to nuke a hugetlb page table
when unmapping or migrating a hugetlb page, and will change to use
huge_ptep_clear_flush() instead in the following patches.
So this is a preparation patch, which changes the huge_ptep_clear_flush()
to return the original pte to help to nuke a hugetlb page table.
[baolin.wang@linux.alibaba.com: fix build in several more architectures]
Link: https://lkml.kernel.org/r/0009a4cd-2826-e8be-e671-f050d4f18d5d@linux.alibaba.com
[sfr@canb.auug.org.au: fixup]
Link: https://lkml.kernel.org/r/20220511181531.7f27a5c1@canb.auug.org.au
Link: https://lkml.kernel.org/r/cover.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/20f77ddab90baa249bd24504c413189b82acde69.1652270205.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/cover.1652147571.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/dcf065868cce35bceaf138613ad27f17bb7c0c19.1652147571.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Rich Felker <dalias@libc.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Extend and rework the "Temporary Virtual Mappings" section of the
highmem.rst documentation.
Despite the local kmaps were introduced by Thomas Gleixner in October
2020, documentation was still missing information about them. These
additions rely largely on Gleixner's patches, Jonathan Corbet's LWN
articles, comments by Ira Weiny and Matthew Wilcox, and in-code comments
from ./include/linux/highmem.h.
1) Add a paragraph to document kmap_local_page().
2) Reorder the list of functions by decreasing order of preference
of use.
3) Rework part of the kmap() entry in list.
Link: https://lkml.kernel.org/r/20220428212455.892-5-fmdefrancesco@gmail.com
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The use of kmap_atomic() is new code is being deprecated in favor of
kmap_local_page(). For this reason the "Using kmap_atomic" section in
highmem.rst is obsolete and unnecessary, but it can still help developers
if it were moved to kdocs in highmem.h.
Therefore, move the relevant parts of this section from highmem.rst and
merge them with the kdocs in highmem.h.
Link: https://lkml.kernel.org/r/20220428212455.892-4-fmdefrancesco@gmail.com
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
kernel-docs that are in include/linux/highmem.h and in
include/linux/highmem-internal.h should be included in highmem.rst.
Use kdocs directives to include the above-mentioned comments into
highmem.rst.
Link: https://lkml.kernel.org/r/20220428212455.892-3-fmdefrancesco@gmail.com
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Extend and reorganize Highmem's documentation", v4.
This series has the purpose to extend and reorganize Highmem's
documentation.
This is a work in progress because some information should still be moved
from highmem.rst to highmem.h and highmem-internal.h. Specifically I'm
talking about moving the "how to" information to the relevant headers, as
it as been suggested by Ira Weiny (Intel).
Also, this is a work in progress because some kdocs in highmem.h and
highmem-internal.h should be improved.
This patch (of 4):
`scripts/kernel-doc -v -none include/linux/highmem*` reports the following
warnings:
include/linux/highmem.h:160: warning: expecting prototype for kunmap_atomic(). Prototype was for nr_free_highpages() instead
include/linux/highmem.h:204: warning: No description found for return value of 'alloc_zeroed_user_highpage_movable'
include/linux/highmem-internal.h:256: warning: Function parameter or member '__addr' not described in 'kunmap_atomic'
include/linux/highmem-internal.h:256: warning: Excess function parameter 'addr' description in 'kunmap_atomic'
Fix these warnings by (1) moving the kernel-doc comments from highmem.h to
highmem-internal.h (which is the file were the kunmap_atomic() macro is
actually defined), (2) extending and merging it with the comment which was
already in highmem-internal.h, and (3) using correct parameter names (4)
correcting a few technical inaccuracies in comments, and (5) adding a
deprecation notice in kunmap_atomic() for consistency with kmap_atomic().
Link: https://lkml.kernel.org/r/20220428212455.892-1-fmdefrancesco@gmail.com
Link: https://lkml.kernel.org/r/20220428212455.892-2-fmdefrancesco@gmail.com
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
fbdev:
- revert NULL deref fix that turned into a use-after-free
- prevent use-after-free in fbdev
- efifb/simplefb/vesafb: fix cleanup paths to avoid use-after-frees
dma-buf:
- fix panic in stats setup
vc4:
- fix hdmi build
nouveau:
- tegra iommu present fix
- fix leak in backlight name
vmwgfx:
- Black screen due to fences using FIFO checks on SVGA3
- Random black screens on boot due to uninitialized drm_mode_fb_cmd2
- Hangs on SVGA3 due to command buffers being used with gbobjects
-----BEGIN PGP SIGNATURE-----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=wF/s
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2022-05-14' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"Turns out I was right, some fixes hadn't made it to me yet. The vmwgfx
ones also popped up later, but all seem like bad enough things to fix.
The dma-buf, vc4 and nouveau ones are all pretty small.
The fbdev fixes are a bit more complicated: a fix to cleanup fbdev
devices properly, uncovered some use-after-free bugs in existing
drivers. Then the fix for those bugs wasn't correct. This reverts that
fix, and puts the proper fixes in place in the drivers to avoid the
use-after-frees.
This has had a fair number of eyes on it at this stage, and I'm
confident enough that it puts things in the right place, and is less
dangerous than reverting our way out of the initial change at this
stage.
fbdev:
- revert NULL deref fix that turned into a use-after-free
- prevent use-after-free in fbdev
- efifb/simplefb/vesafb: fix cleanup paths to avoid use-after-frees
dma-buf:
- fix panic in stats setup
vc4:
- fix hdmi build
nouveau:
- tegra iommu present fix
- fix leak in backlight name
vmwgfx:
- Black screen due to fences using FIFO checks on SVGA3
- Random black screens on boot due to uninitialized drm_mode_fb_cmd2
- Hangs on SVGA3 due to command buffers being used with gbobjects"
* tag 'drm-fixes-2022-05-14' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Disable command buffers on svga3 without gbobjects
drm/vmwgfx: Initialize drm_mode_fb_cmd2
drm/vmwgfx: Fix fencing on SVGAv3
drm/vc4: hdmi: Fix build error for implicit function declaration
dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
fbdev: efifb: Fix a use-after-free due early fb_info cleanup
drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
drm/nouveau/tegra: Stop using iommu_present()
fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: Prevent possible use-after-free in fb_release()
Revert "fbdev: Make fb_release() return -ENODEV if fbdev was unregistered"
The np variable is used globally for stm32_pctl_probe() and in one of
its code branches. cppcheck is not happy with that:
pinctrl-stm32.c:1530:23: warning: Local variable 'np' shadows outer variable [shadowVariable]
Instead of simply renaming one of the variables convert some code to
use a device pointer directly.
Fixes: bb949ed9b1 ("pinctrl: stm32: Switch to use for_each_gpiochip_node() helper")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20220507102257.26414-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, dumping almost all BTFs specified by id requires
using the -B option to pass the base BTF. For kernel module
BTFs the vmlinux BTF sysfs path should work.
This patch simplifies dumping by ID usage by loading
vmlinux BTF from sysfs as base, if base BTF was not specified
and the ID corresponds to a kernel module BTF.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20220513121743.12411-1-larysa.zaremba@intel.com
The manual describes function 0x6 of pin PA2 as "SPI1_CLK", so change
the comment to reflect that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220504170736.2669595-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change suniv f1c100s pinctrl,PD14 multiplexing function lvds1 to uart2
When the pin PD13 and PD14 is setting up to uart2 function in dts,
there's an error occurred:
1c20800.pinctrl: unsupported function uart2 on pin PD14
Because 'uart2' is not any one multiplexing option of PD14,
and pinctrl don't know how to configure it.
So change the pin PD14 lvds1 function to uart2.
Signed-off-by: IotaHydrae <writeforever@foxmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/tencent_70C1308DDA794C81CAEF389049055BACEC09@qq.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before commit 322cff70d4 the fifo_time member of requests on a dispatch
list was not used. Commit 322cff70d4 introduces code that reads the
fifo_time member of requests on dispatch lists. Hence this patch that sets
the fifo_time member when adding a request to a dispatch list.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Fixes: 322cff70d4 ("block/mq-deadline: Prioritize high-priority requests")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220513171307.32564-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of having uninitialized versions of arguments as separate
bpf_arg_types (eg ARG_PTR_TO_UNINIT_MEM as the uninitialized version
of ARG_PTR_TO_MEM), we can instead use MEM_UNINIT as a bpf_type_flag
modifier to denote that the argument is uninitialized.
Doing so cleans up some of the logic in the verifier. We no longer
need to do two checks against an argument type (eg "if
(base_type(arg_type) == ARG_PTR_TO_MEM || base_type(arg_type) ==
ARG_PTR_TO_UNINIT_MEM)"), since uninitialized and initialized
versions of the same argument type will now share the same base type.
In the near future, MEM_UNINIT will be used by dynptr helper functions
as well.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/r/20220509224257.3222614-2-joannelkoong@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
iommu detection improvement for nouveau, a memory leak fix for nouveau,
pointer dereference fix for dma_buf_file_release(), and a build breakage
fix for vc4
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYn4I8QAKCRDj7w1vZxhR
xTQqAQCERNogpvxEuKGk1643nNiPtDLbYcwJMifqa7sQIQk13AD9EKR9oV+JyIZj
2tS06uFF1qWQeXAgS8wGToirZ2E3Fgo=
=a0hl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2022-05-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Multiple fixes to fbdev to address a regression at unregistration, an
iommu detection improvement for nouveau, a memory leak fix for nouveau,
pointer dereference fix for dma_buf_file_release(), and a build breakage
fix for vc4
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220513073044.ymayac7x7bzatrt7@houat
The asynchronous zspage free worker tries to lock a zspage's entire page
list without defending against page migration. Since pages which haven't
yet been locked can concurrently migrate off the zspage page list while
lock_zspage() churns away, lock_zspage() can suffer from a few different
lethal races.
It can lock a page which no longer belongs to the zspage and unsafely
dereference page_private(), it can unsafely dereference a torn pointer to
the next page (since there's a data race), and it can observe a spurious
NULL pointer to the next page and thus not lock all of the zspage's pages
(since a single page migration will reconstruct the entire page list, and
create_page_chain() unconditionally zeroes out each list pointer in the
process).
Fix the races by using migrate_read_lock() in lock_zspage() to synchronize
with page migration.
Link: https://lkml.kernel.org/r/20220509024703.243847-1-sultan@kerneltoast.com
Fixes: 77ff465799 ("zsmalloc: zs_page_migrate: skip unnecessary loops but not return -EBUSY if zspage is not inuse")
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This reverts commit a4efc174b3 which introduced a regression issue
that when there're multiple processes allocating dma memory in parallel by
calling dma_alloc_coherent(), it may fail sometimes as follows:
Error log:
cma: cma_alloc: linux,cma: alloc failed, req-size: 148 pages, ret: -16
cma: number of available pages:
3@125+20@172+12@236+4@380+32@736+17@2287+23@2473+20@36076+99@40477+108@40852+44@41108+20@41196+108@41364+108@41620+
108@42900+108@43156+483@44061+1763@45341+1440@47712+20@49324+20@49388+5076@49452+2304@55040+35@58141+20@58220+20@58284+
7188@58348+84@66220+7276@66452+227@74525+6371@75549=> 33161 free of 81920 total pages
When issue happened, we saw there were still 33161 pages (129M) free CMA
memory and a lot available free slots for 148 pages in CMA bitmap that we
want to allocate.
When dumping memory info, we found that there was also ~342M normal
memory, but only 1352K CMA memory left in buddy system while a lot of
pageblocks were isolated.
Memory info log:
Normal free:351096kB min:30000kB low:37500kB high:45000kB reserved_highatomic:0KB
active_anon:98060kB inactive_anon:98948kB active_file:60864kB inactive_file:31776kB
unevictable:0kB writepending:0kB present:1048576kB managed:1018328kB mlocked:0kB
bounce:0kB free_pcp:220kB local_pcp:192kB free_cma:1352kB lowmem_reserve[]: 0 0 0
Normal: 78*4kB (UECI) 1772*8kB (UMECI) 1335*16kB (UMECI) 360*32kB (UMECI) 65*64kB (UMCI)
36*128kB (UMECI) 16*256kB (UMCI) 6*512kB (EI) 8*1024kB (UEI) 4*2048kB (MI) 8*4096kB (EI)
8*8192kB (UI) 3*16384kB (EI) 8*32768kB (M) = 489288kB
The root cause of this issue is that since commit a4efc174b3 ("mm/cma.c:
remove redundant cma_mutex lock"), CMA supports concurrent memory
allocation. It's possible that the memory range process A trying to alloc
has already been isolated by the allocation of process B during memory
migration.
The problem here is that the memory range isolated during one allocation
by start_isolate_page_range() could be much bigger than the real size we
want to alloc due to the range is aligned to MAX_ORDER_NR_PAGES.
Taking an ARMv7 platform with 1G memory as an example, when
MAX_ORDER_NR_PAGES is big (e.g. 32M with max_order 14) and CMA memory is
relatively small (e.g. 128M), there're only 4 MAX_ORDER slot, then it's
very easy that all CMA memory may have already been isolated by other
processes when one trying to allocate memory using dma_alloc_coherent().
Since current CMA code will only scan one time of whole available CMA
memory, then dma_alloc_coherent() may easy fail due to contention with
other processes.
This patch simply falls back to the original method that using cma_mutex
to make alloc_contig_range() run sequentially to avoid the issue.
Link: https://lkml.kernel.org/r/20220509094551.3596244-1-aisheng.dong@nxp.com
Link: https://lore.kernel.org/all/20220315144521.3810298-2-aisheng.dong@nxp.com/
Fixes: a4efc174b3 ("mm/cma.c: remove redundant cma_mutex lock")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [5.11+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
