Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The refactoring and consolidation of <asm/pgalloc.h> caused regression
on parisc and ia64. The fix for parisc made it into v5.9-rc1 while the
fix ia64 got delayed a bit and here it is.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAl87qP8THHJwcHRAbGlu
dXguaWJtLmNvbQAKCRA5A4Ymyw79keEuB/4yCQjJbW+0y+DaivCjUtAPpBek+tpn
sYW5nWFiE4JlTfZf1ujQ4QpHHkL9y8OXo3zfE1G49lCT97j1GveMpEu68k31+YjO
uhLY9mv7kFlkuDTgrdkCKOJg+e8HmM6NRUEGJ+Vxoo03S9jpqWjckAURGaluEI/w
uoI8f64Apc6bjGiOygUIva73B2RGjWOnfoVecy0h7EMRrRHgQV/sJQWHRKVcHKok
3Mdnswzg07jmR55GTJtm0rO78h/+5B0FCgr1iOK9oo0tMkxSk3DS0Xy7eHhlPaX4
x1gqhi11XsqDowJfMr/WyfpjGFUp2/yeRoNux1L34zFdxxxKCNowvXk0
=h7gw
-----END PGP SIGNATURE-----
Merge tag 'fixes-2020-08-18' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull ia64 page table fix from Mike Rapoport:
"Fix regression in IA-64 caused by page table allocation refactoring
The refactoring and consolidation of <asm/pgalloc.h> caused regression
on parisc and ia64. The fix for parisc made it into v5.9-rc1 while the
fix ia64 got delayed a bit and here it is"
* tag 'fixes-2020-08-18' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
arch/ia64: Restore arch-specific pgd_offset_k implementation
Recently we found regression when running will_it_scale/page_fault3 test
on ARM64. Over 70% down for the multi processes cases and over 20% down
for the multi threads cases. It turns out the regression is caused by
commit 89b15332af ("mm: drop mmap_sem before calling
balance_dirty_pages() in write fault").
The test mmaps a memory size file then write to the mapping, this would
make all memory dirty and trigger dirty pages throttle, that upstream
commit would release mmap_sem then retry the page fault. The retried
page fault would see correct PTEs installed then just fall through to
spurious TLB flush. The regression is caused by the excessive spurious
TLB flush. It is fine on x86 since x86's spurious TLB flush is no-op.
We could just skip the spurious TLB flush to mitigate the regression.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Xu Yu <xuyu@linux.alibaba.com>
Debugged-by: Xu Yu <xuyu@linux.alibaba.com>
Tested-by: Xu Yu <xuyu@linux.alibaba.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Yang Shi <shy828301@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ext4_generic_delete_entry function does not use the parameter
handle, so it can be removed.
Signed-off-by: Kyoungho Koo <rnrudgh@gmail.com>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/20200810080701.GA14160@koo-Z370-HD3
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
seq_puts is a lot cheaper than seq_printf, so use that to print
literal strings.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/20200810022158.9167-1-vulab@iscas.ac.cn
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
It might be better to adjust the code in two places:
1. Determine whether grp is currupt or not should be placed first.
2. (cr<=2 && free <ac->ac_g_ex.fe_len)should may belong to the crx
strategy, and it may be more appropriate to put it in the
subsequent switch statement block. For cr1, cr2, the conditions
in switch potentially realize the above judgment. For cr0, we
should add (free <ac->ac_g_ex.fe_len) judgment, and then delete
(free / fragments) >= ac->ac_g_ex.fe_len), because cr0 returns
true by default.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/e20b2d8f-1154-adb7-3831-a9e11ba842e9@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
These comments do not seem to be related to ext4_mb_check_limits(),
it may be invalid.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Reviewed-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/c49faf0c-d5d5-9c51-6911-9e0ff57c6bfa@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This reverts commit d313279228.
This patch causes a regression with quite a few devices, as probing fails
because of the race where the first IRQ is dropped on the floor (after
hid_device_io_start() happens, but before the 50ms timeout passess), and
report descriptor never gets parsed and populated.
As this is just a boot time micro-optimization, let's revert the
patch for 5.9 now, and fix this properly eventually for next merge
window.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208935
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Reported-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ppc64le we get the following warning:
In file included from btf_dump.c:16:0:
btf_dump.c: In function ‘btf_dump_emit_struct_def’:
../include/linux/kernel.h:20:17: error: comparison of distinct pointer types lacks a cast [-Werror]
(void) (&_max1 == &_max2); \
^
btf_dump.c:882:11: note: in expansion of macro ‘max’
m_sz = max(0LL, btf__resolve_size(d->btf, m->type));
^~~
Fix by explicitly casting to __s64, which is a return type from
btf__resolve_size().
Fixes: 702eddc77a ("libbpf: Handle GCC built-in types for Arm NEON")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200818164456.1181661-1-andriin@fb.com
Define shutdown callback for display drm driver,
so as to disable all the CRTCS when shutdown
notification is received by the driver.
This change will turn off the timing engine so
that no display transactions are requested
while mmu translations are getting disabled
during reboot sequence.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Changes in v2:
- Remove NULL check from msm_pdev_shutdown (Stephen Boyd)
- Change commit text to reflect when this issue
was uncovered (Sai Prakash Ranjan)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Changes from v1:
- update commit description with proper ref-accounting justification
commit db37a34c56 ("block, bfq: get a ref to a group when adding it to a service tree")
introduce leak forbfq_group and blkcg_gq objects because of get/put
imbalance.
In fact whole idea of original commit is wrong because bfq_group entity
can not dissapear under us because it is referenced by child bfq_queue's
entities from here:
-> bfq_init_entity()
->bfqg_and_blkg_get(bfqg);
->entity->parent = bfqg->my_entity
-> bfq_put_queue(bfqq)
FINAL_PUT
->bfqg_and_blkg_put(bfqq_group(bfqq))
->kmem_cache_free(bfq_pool, bfqq);
So parent entity can not disappear while child entity is in tree,
and child entities already has proper protection.
This patch revert commit db37a34c56 ("block, bfq: get a ref to a group when adding it to a service tree")
bfq_group leak trace caused by bad commit:
-> blkg_alloc
-> bfq_pq_alloc
-> bfqg_get (+1)
->bfq_activate_bfqq
->bfq_activate_requeue_entity
-> __bfq_activate_entity
->bfq_get_entity
->bfqg_and_blkg_get (+1) <==== : Note1
->bfq_del_bfqq_busy
->bfq_deactivate_entity+0x53/0xc0 [bfq]
->__bfq_deactivate_entity+0x1b8/0x210 [bfq]
-> bfq_forget_entity(is_in_service = true)
entity->on_st_or_in_serv = false <=== :Note2
if (is_in_service)
return; ==> do not touch reference
-> blkcg_css_offline
-> blkcg_destroy_blkgs
-> blkg_destroy
-> bfq_pd_offline
-> __bfq_deactivate_entity
if (!entity->on_st_or_in_serv) /* true, because (Note2)
return false;
-> bfq_pd_free
-> bfqg_put() (-1, byt bfqg->ref == 2) because of (Note2)
So bfq_group and blkcg_gq will leak forever, see test-case below.
##TESTCASE_BEGIN:
#!/bin/bash
max_iters=${1:-100}
#prep cgroup mounts
mount -t tmpfs cgroup_root /sys/fs/cgroup
mkdir /sys/fs/cgroup/blkio
mount -t cgroup -o blkio none /sys/fs/cgroup/blkio
# Prepare blkdev
grep blkio /proc/cgroups
truncate -s 1M img
losetup /dev/loop0 img
echo bfq > /sys/block/loop0/queue/scheduler
grep blkio /proc/cgroups
for ((i=0;i<max_iters;i++))
do
mkdir -p /sys/fs/cgroup/blkio/a
echo 0 > /sys/fs/cgroup/blkio/a/cgroup.procs
dd if=/dev/loop0 bs=4k count=1 of=/dev/null iflag=direct 2> /dev/null
echo 0 > /sys/fs/cgroup/blkio/cgroup.procs
rmdir /sys/fs/cgroup/blkio/a
grep blkio /proc/cgroups
done
##TESTCASE_END:
Fixes: db37a34c56 ("block, bfq: get a ref to a group when adding it to a service tree")
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IA32_MCG_STATUS.RIPV indicates whether the return RIP value pushed onto
the stack as part of machine check delivery is valid or not.
Various drivers copied a code fragment that uses the RIPV bit to
determine the severity of the error as either HW_EVENT_ERR_UNCORRECTED
or HW_EVENT_ERR_FATAL, but this check is reversed (marking errors where
RIPV is set as "FATAL").
Reverse the tests so that the error is marked fatal when RIPV is not set.
Reported-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200707194324.14884-1-tony.luck@intel.com
wired_cmd_repeater_auth_stream_req_in has a variable
length array at the end. we use struct_size() overflow
macro to determine the size for the allocation and sending
size.
This also fixes bug in case number of streams is > 0 in the original
submission. This bug was not triggered as the number of streams is
always one.
Fixes: c56967d674 (mei: hdcp: Replace one-element array with flexible-array member)
Fixes: 0a1af1b5c1 (misc/mei/hdcp: Verify M_prime)
Cc: <stable@vger.kernel.org> # v5.1+: c56967d674 (mei: hdcp: Replace one-element array with flexible-array member)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200818075406.2532605-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work
even if UART isn't console") worked pretty well and I've been doing a
lot of debugging with it. However, recently I typed "dmesg" in kdb
and then held the space key down to scroll through the pagination. My
device hung. This was repeatable and I found that it was introduced
with the aforementioned commit.
It turns out that there are some strange boundary cases in geni where
in some weird situations it will signal RX_LAST but then will put 0 in
RX_LAST_BYTE. This means that the entire last FIFO entry is valid.
This weird corner case is handled in qcom_geni_serial_handle_rx()
where you can see that we only honor RX_LAST_BYTE if RX_LAST is set
_and_ RX_LAST_BYTE is non-zero. If either of these is not true we use
BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word.
Let's fix kgdb. While at it, also use the proper #define for 4.
Fixes: e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check to fbcon_resize() to ensure that a possible change to user font
height or user font width will not allow a font data out-of-bounds access.
NOTE: must use original charcount in calculation as font charcount can
change and cannot be used to determine the font data allocated size.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/1596213192-6635-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I do not know when ConfigInfoView::createStandardContextMenu() is
called.
Because QTextEdit::createStandardContextMenu() is not virtual,
ConfigInfoView::createStandardContextMenu() cannot override it.
Even if right-click the ConfigInfoView window, the "Show Debug Info"
menu does not show up.
Build up the menu in the constructor, and invoke it from the
contextMenuEvent().
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
If you right-click in the ConfigList window, you will see the following
messages in the console:
QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:888
QObject::connect: (sender name: 'config')
QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:897
QObject::connect: (sender name: 'config')
QObject::connect: No such slot QAction::setOn(bool) in scripts/kconfig/qconf.cc:906
QObject::connect: (sender name: 'config')
Right, there is no such slot in QAction. I think this is a typo of
setChecked.
Due to this bug, when you toggled the menu "Option->Show Name/Range/Data"
the state of the context menu was not previously updated. Fix this.
Fixes: d5d973c3f8 ("Port xconfig to Qt5 - Put back some of the old implementation(part 2)")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Use the proper form of the RESTRICT keyword.
Quote the comments properly too.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The '%' in filter/filter-out matches to any number of any characters,
including empty string.
So, '%config' matches to 'config', and '%install' to 'install'.
Drop the redundant patterns.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Fix the following warning from sparse:
scripts/extract-cert.c:74:5: warning: symbol 'kbuild_verbose' was not declared. Should it be static?
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Drivers using serialio were already made available in Kconfig only under
the ISA condition.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20200804160659.7y76sdseow43lfms@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was missed while introducing the tty-based serial access.
The only remaining use of wait_for_xmitr with tty-based access is in
spk_synth_is_alive_restart to check whether the synth can be restarted.
With tty-based this is up to the tty layer to cope with the buffering
etc. so we can just say yes.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20200804160637.x3iycau5izywbgzl@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.
After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.
Trigger a reprobe ourselves when new specialised drivers get registered.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only ever used the ID table matching before, but we should also support
open-coded match functions.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and
"otg_usb3_port" with -EINVAL because "0" is a valid value
represents usb2 port 0 or usb3 port 0.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.
This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.
Cc: stable@vger.kernel.org
Fixes: 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.
This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix 2 unlocked ucsi_run_command calls:
1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().
2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().
This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():
AB order:
1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
which takes ucsi_connector->lock
BA order:
1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
ucsi->ppm_lock
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).
Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
(through ucsi_partner_change())
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") introduced the use of a "match" function to select a
non-generic/better driver for a particular USB device. This
unfortunately breaks the operation of usbip in general, as reported in
the kernel bugzilla with bug 208267 (linked below).
Upon inspecting the aforementioned commit, one can observe that the
original code in the usb_device_match function used to return 1
unconditionally, but the aforementioned commit makes the usb_device_match
function use identifier tables and "match" virtual functions, if either of
them are available.
Hence, this commit implements a match function for usbip that
unconditionally returns true to ensure that usbip is functional again.
This change has been verified to restore usbip functionality, with a
v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses
usbip to redirect USB devices between VMs.
Thanks to Jonathan Dieter for the effort in bisecting this issue down
to the aforementioned commit.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443
Link: https://github.com/QubesOS/qubes-issues/issues/5905
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: <stable@vger.kernel.org> # 5.7
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
