The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The "seg_num," line wasn't indented. All the arguments can fit nicely
on two lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After commit 9cce844abf ("MIPS: CPU#0 is not hotpluggable"),
c->hotpluggable is 0 for CPU 0 and it will not generate a control
file in sysfs for this CPU:
[root@linux loongson]# cat /sys/devices/system/cpu/cpu0/online
cat: /sys/devices/system/cpu/cpu0/online: No such file or directory
[root@linux loongson]# echo 0 > /sys/devices/system/cpu/cpu0/online
bash: /sys/devices/system/cpu/cpu0/online: Permission denied
So no need to check CPU 0 in {loongson3,bmips,octeon}_cpu_disable(),
just remove them.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
kfree(dev) has been called inside put_device so anther
kfree would cause a use-after-free bug/
Fixes: 8286ae0330 ("MIPS: Add CDMM bus support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch provides the test application for DMA_MAP_BENCHMARK.
Before running the test application, we need to bind a device to dma_map_
benchmark driver. For example, unbind "xxx" from its original driver and
bind to dma_map_benchmark:
echo dma_map_benchmark > /sys/bus/platform/devices/xxx/driver_override
echo xxx > /sys/bus/platform/drivers/xxx/unbind
echo xxx > /sys/bus/platform/drivers/dma_map_benchmark/bind
Another example for PCI devices:
echo dma_map_benchmark > /sys/bus/pci/devices/0000:00:01.0/driver_override
echo 0000:00:01.0 > /sys/bus/pci/drivers/xxx/unbind
echo 0000:00:01.0 > /sys/bus/pci/drivers/dma_map_benchmark/bind
The below command will run 16 threads on numa node 0 for 10 seconds on
the device bound to dma_map_benchmark platform_driver or pci_driver:
./dma_map_benchmark -t 16 -s 10 -n 0
dma mapping benchmark: threads:16 seconds:10
average map latency(us):1.1 standard deviation:1.9
average unmap latency(us):0.5 standard deviation:0.8
Cc: Will Deacon <will@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Nowadays, there are increasing requirements to benchmark the performance
of dma_map and dma_unmap particually while the device is attached to an
IOMMU.
This patch enables the support. Users can run specified number of threads
to do dma_map_page and dma_unmap_page on a specific NUMA node with the
specified duration. Then dma_map_benchmark will calculate the average
latency for map and unmap.
A difficulity for this benchmark is that dma_map/unmap APIs must run on
a particular device. Each device might have different backend of IOMMU or
non-IOMMU.
So we use the driver_override to bind dma_map_benchmark to a particual
device by:
For platform devices:
echo dma_map_benchmark > /sys/bus/platform/devices/xxx/driver_override
echo xxx > /sys/bus/platform/drivers/xxx/unbind
echo xxx > /sys/bus/platform/drivers/dma_map_benchmark/bind
For PCI devices:
echo dma_map_benchmark > /sys/bus/pci/devices/0000:00:01.0/driver_override
echo 0000:00:01.0 > /sys/bus/pci/drivers/xxx/unbind
echo 0000:00:01.0 > /sys/bus/pci/drivers/dma_map_benchmark/bind
Cc: Will Deacon <will@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
[hch: folded in two fixes from Colin Ian King <colin.king@canonical.com>]
Signed-off-by: Christoph Hellwig <hch@lst.de>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
So far we have been using huge DMA windows to map all the RAM available.
The RAM is normally mapped to the VM address space contiguously, and
there is always a reasonable upper limit for possible future hot plugged
RAM which makes it easy to map all RAM via IOMMU.
Now there is persistent memory ("ibm,pmemory" in the FDT) which (unlike
normal RAM) can map anywhere in the VM space beyond the maximum RAM size
and since it can be used for DMA, it requires extending the huge window
up to MAX_PHYSMEM_BITS which requires hypervisor support for:
1. huge TCE tables;
2. multilevel TCE tables;
3. huge IOMMU pages.
Certain hypervisors cannot do either so the only option left is
restricting the huge DMA window to include only RAM and fallback to
the default DMA window for persistent memory.
This defines arch_dma_map_direct/etc to allow generic DMA code perform
additional checks on whether direct DMA is still possible.
This checks if the system has persistent memory. If it does not,
the DMA bypass mode is selected, i.e.
* dev->bus_dma_limit = 0
* dev->dma_ops_bypass = true <- this avoid calling dma_ops for mapping.
If there is such memory, this creates identity mapping only for RAM and
sets the dev->bus_dma_limit to let the generic code decide whether to
call into the direct DMA or the indirect DMA ops.
This should not change the existing behaviour when no persistent memory
as dev->dma_ops_bypass is expected to be set.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
At the moment we allow bypassing DMA ops only when we can do this for
the entire RAM. However there are configs with mixed type memory
where we could still allow bypassing IOMMU in most cases;
POWERPC with persistent memory is one example.
This adds an arch hook to determine where bypass can still work and
we invoke direct DMA API. The following patch checks the bus limit
on POWERPC to allow or disallow direct mapping.
This adds a ARCH_HAS_DMA_MAP_DIRECT config option to make the arch_xxxx
hooks no-op by default.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Provide a weak plat_get_fdt() in relocate.c in case some platform enable
USE_OF while plat_get_fdt() is useless.
1MB RELOCATION_TABLE_SIZE is small for Loongson64 because too many
instructions should be relocated. 2MB is enough in present.
Add KASLR support for Loongson64.
KASLR(kernel address space layout randomization)
To enable KASLR on Loongson64:
First, make loongson3_defconfig.
Then, enable CONFIG_RELOCATABLE and CONFIG_RANDOMIZE_BASE.
Finally, compile the kernel.
To test KASLR on Loongson64:
Start machine with KASLR kernel.
The first time:
# cat /proc/iomem
00200000-0effffff : System RAM
02f30000-03895e9f : Kernel code
03895ea0-03bc7fff : Kernel data
03e30000-04f43f7f : Kernel bss
The second time:
# cat /proc/iomem
00200000-0effffff : System RAM
022f0000-02c55e9f : Kernel code
02c55ea0-02f87fff : Kernel data
031f0000-04303f7f : Kernel bss
We see that code, data and bss sections become randomize.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Apply_r_mips_26_rel() relocates instructions like j, jal and etc. These
instructions consist of 6bits function field and 26bits address field.
The value of target_addr as follows,
=================================================================
| high 4bits | low 28bits |
=================================================================
|the high 4bits of this PC | the low 26bits of instructions << 2|
=================================================================
Thus, loc_orig and log_new both need high 4bits rather than high 6bits.
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, HDMI, DSI, CSI, and an expansion header.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8167
board.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8167 SoC provides the following peripherals: GPIO, UART, USB2,
SPI, eMMC, SDIO, NAND, Flash, ADC, I2C, PWM, TImers, IR, Ethernet,
Audio (I2S, SPDIF, TDM, HDMI), HDMI, DSI, CSI, MDP (Multimedia Data
Path), Video encoding (H.264), Video Decoding (H.264, VP8).
The MT8167 is compatible with MT8516 but provides multimedia IPs to it.
This commit is just adding the basic dtsi file with the support of the
following IOs: GPIO, Clocks.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-2-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The driver references of_device_id table via of_match_device() so it
will be unused for !CONFIG_OF builds:
drivers/mfd/twl6030-irq.c:359:34: warning: ‘twl6030_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match either via ACPI or OF. Its of_device_id table is
referenced via of_match_ptr() so it will be unused for !CONFIG_OF
builds:
drivers/mfd/axp20x-i2c.c:60:34: warning: ‘axp20x_i2c_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/wm8994-core.c:618:34: warning: ‘wm8994_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/sun4i-gpadc.c:79:34: warning: ‘sun4i_gpadc_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/max77686.c:148:34: warning: ‘max77686_pmic_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/stmfx.c:542:34: warning: ‘stmfx_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/rt5033.c:116:34: warning: ‘rt5033_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/mt6397-core.c:214:34: warning: ‘mt6397_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/max77650.c:215:34: warning: ‘max77650_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/fsl-imx25-tsadc.c:190:34: warning: ‘mx25_tsadc_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/ene-kb3930.c:194:34: warning: ‘kb3930_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9150-core.c:505:34: warning: ‘da9150_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9063-i2c.c:348:34: warning: ‘da9063_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9062-core.c:614:34: warning: ‘da9062_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9055-i2c.c:66:34: warning: ‘da9055_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/bcm590xx.c:95:34: warning: ‘bcm590xx_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD_OMAP_USB_HOST uses Common Clock Framework thus it cannot be
built on platforms without it (e.g. compile test on MIPS with LANTIQ):
mips-linux-ld: drivers/mfd/omap-usb-host.o: in function `usbhs_omap_probe':
omap-usb-host.c:(.text+0x940): undefined reference to `clk_set_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the detection order to priorize DMI table entries over available
ACPI entries.
This makes it more easy for product developers to patch product specific
handling into the driver.
Furthermore it allows to simplify the implementation a bit and
especially to remove the need to force synchronous probing.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Correct power-off programming sequence in order to fix shutting down
devices which are using TPS65910 PMIC.
In accordance to the TPS65910 datasheet, the PMIC's state-machine
transitions into the OFF state only when DEV_OFF bit of DEVCTRL_REG is
set. The ON / SLEEP states also should be cleared, otherwise PMIC won't
get into a proper state on shutdown. Devices like Nexus 7 tablet and Ouya
game console are shutting down properly now.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Zack Pearsall <zpearsall@yahoo.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/altera-sysmgr.c:155:36-39: WARNING: Suspicious code. resource_size is maybe missing with res
Generated by: scripts/coccinelle/api/resource_size.cocci
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SPI bus number must be assigned dynamically for each device, otherwise it
will crash when multiple devices are plugged to system.
Reported-and-tested-by: syzbot+c60ddb60b685777d9d59@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When a packet is fragmented by batman-adv, the original batman-adv header
is not modified. Only a new fragmentation is inserted between the original
one and the ethernet header. The code must therefore make sure that it has
a writable region of this size in the skbuff head.
But it is not useful to always reallocate the skbuff by this size even when
there would be more than enough headroom still in the skb. The reallocation
is just to costly during in this codepath.
Fixes: ee75ed8887 ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv net_device is trying to propagate the needed_headroom and
needed_tailroom from the lower devices. This is needed to avoid cost
intensive reallocations using pskb_expand_head during the transmission.
But the fragmentation code split the skb's without adding extra room at the
end/beginning of the various fragments. This reduced the performance of
transmissions over complex scenarios (batadv on vxlan on wireguard) because
the lower devices had to perform the reallocations at least once.
Fixes: ee75ed8887 ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.
This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.
Fixes: 7bca68c784 ("batman-adv: Add lower layer needed_(head|tail)room to own ones")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In msi2500_stop_streaming(), there is an if statement on line 870 to
check whether dev->udev is NULL:
if (dev->udev)
When dev->udev is NULL, it is used on line 877:
msi2500_ctrl_msg(dev, CMD_STOP_STREAMING, 0)
usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0), ...)
Thus, a possible null-pointer dereference may occur.
To fix this bug, dev->udev is checked before calling msi2500_ctrl_msg().
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add a new label that puts the last used
node, and edit the goto statements in the middle of the loop to first go
to the new label.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported on:
https://lore.kernel.org/linux-media/20190627222020.45909-1-willemdebruijn.kernel@gmail.com/
if gp8psk_usb_in_op() returns an error, the status var is not
initialized. Yet, this var is used later on, in order to
identify:
- if the device was already started;
- if firmware has loaded;
- if the LNBf was powered on.
Using status = 0 seems to ensure that everything will be
properly powered up.
So, instead of the proposed solution, let's just set
status = 0.
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the setting of DMA cache parameters, program more appropriate
values and explicitly set sharability domain.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'pci_set_dma_mask()' + 'pci_set_consistent_dma_mask()' can be replaced by
an equivalent 'dma_set_mask_and_coherent()' which is much less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
