When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
of passing it to the stack immediately, place it on a list in the napi
struct. Then, at flush time (napi_complete_done(), napi_poll(), or
napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
!napi->gro_bitmask, so we have to do it in the callers instead. (There are
a handful of drivers that call napi_gro_flush() themselves, but it's not
clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
list whenever it exceeds gro_normal_batch, a new net/core sysctl that
defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/acpi/scan.c: document why we don't need the device_hotplug_lock
memremap: move from kernel/ to mm/
lib/test_meminit.c: use GFP_ATOMIC in RCU critical section
asm-generic: fix -Wtype-limits compiler warnings
cgroup: kselftest: relax fs_spec checks
mm/memory_hotplug.c: remove unneeded return for void function
mm/migrate.c: initialize pud_entry in migrate_vma()
coredump: split pipe command whitespace before expanding template
page flags: prioritize kasan bits over last-cpuid
ubsan: build ubsan.c more conservatively
kasan: remove clang version check for KASAN_STACK
mm: compaction: avoid 100% CPU usage during compaction when a task is killed
mm: migrate: fix reference check race between __find_get_block() and migration
mm: vmscan: check if mem cgroup is disabled or not before calling memcg slab shrinker
ocfs2: remove set but not used variable 'last_hash'
Revert "kmemleak: allow to coexist with fault injection"
kernel/signal.c: fix a kernel-doc markup
ARM64 randdconfig builds regularly run into a build error, especially
when NUMA_BALANCING and SPARSEMEM are enabled but not SPARSEMEM_VMEMMAP:
#error "KASAN: not enough bits in page flags for tag"
The last-cpuid bits are already contitional on the available space, so
the result of the calculation is a bit random on whether they were
already left out or not.
Adding the kasan tag bits before last-cpuid makes it much more likely to
end up with a successful build here, and should be reliable for
randconfig at least, as long as that does not randomize NR_CPUS or
NODES_SHIFT but uses the defaults.
In order for the modified check to not trigger in the x86 vdso32 code
where all constants are wrong (building with -m32), enclose all the
definitions with an #ifdef.
[arnd@arndb.de: build fix]
Link: http://lkml.kernel.org/r/CAK8P3a3Mno1SWTcuAOT0Wa9VS15pdU6EfnkxLbDpyS55yO04+g@mail.gmail.com
Link: http://lkml.kernel.org/r/20190722115520.3743282-1-arnd@arndb.de
Link: https://lore.kernel.org/lkml/20190618095347.3850490-1-arnd@arndb.de/
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCXURMOQAKCRCAXGG7T9hj
vqZtAP94YCWvBsB6m3UUEzyOinIj9XaVd+K6ET4C6lLyZRsXBAD7BBMlUQQbuZcW
R1wjdC/oph4y52FgGZY+qE3wfRJhAw8=
=LAXD
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.3a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a small cleanup
- a fix for a build error on ARM with some configs
- a fix of a patch for the Xen gntdev driver
- three patches for fixing a potential problem in the swiotlb-xen
driver which Konrad was fine with me carrying them through the Xen
tree
* tag 'for-linus-5.3a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/swiotlb: remember having called xen_create_contiguous_region()
xen/swiotlb: simplify range_straddles_page_boundary()
xen/swiotlb: fix condition for calling xen_destroy_contiguous_region()
xen: avoid link error on ARM
xen/gntdev.c: Replace vm_map_pages() with vm_map_pages_zero()
xen/pciback: remove set but not used variable 'old_state'
-----BEGIN PGP SIGNATURE-----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=P5E/
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190802' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Here's a small collection of fixes that should go into this series.
This contains:
- io_uring potential use-after-free fix (Jackie)
- loop regression fix (Jan)
- O_DIRECT fragmented bio regression fix (Damien)
- Mark Denis as the new floppy maintainer (Denis)
- ataflop switch fall-through annotation (Gustavo)
- libata zpodd overflow fix (Kees)
- libata ahci deferred probe fix (Miquel)
- nbd invalidation BUG_ON() fix (Munehisa)
- dasd endless loop fix (Stefan)"
* tag 'for-linus-20190802' of git://git.kernel.dk/linux-block:
s390/dasd: fix endless loop after read unit address configuration
block: Fix __blkdev_direct_IO() for bio fragments
MAINTAINERS: floppy: take over maintainership
nbd: replace kill_bdev() with __invalidate_device() again
ata: libahci: do not complain in case of deferred probe
io_uring: fix KASAN use after free in io_sq_wq_submit_work
loop: Fix mount(2) failure due to race with LOOP_SET_FD
libata: zpodd: Fix small read overflow in zpodd_get_mech_type()
ataflop: Mark expected switch fall-through
that started getting exercised differently this time around:
- Select regmap MMIO kconfig in spreadtrum driver to avoid compile
errors
- Complete kerneldoc on devm_clk_bulk_get_optional()
- Register an essential clk earlier on mediatek mt8183 SoCs so
the clocksource driver can use it
- Fix divisor math in the at91 driver
- Plug a race in Renesas reset control logic
-----BEGIN PGP SIGNATURE-----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=tNyv
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few fixes for code that came in during the merge window or that
started getting exercised differently this time around:
- Select regmap MMIO kconfig in spreadtrum driver to avoid compile
errors
- Complete kerneldoc on devm_clk_bulk_get_optional()
- Register an essential clk earlier on mediatek mt8183 SoCs so the
clocksource driver can use it
- Fix divisor math in the at91 driver
- Plug a race in Renesas reset control logic"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: renesas: cpg-mssr: Fix reset control race condition
clk: sprd: Select REGMAP_MMIO to avoid compile errors
clk: mediatek: mt8183: Register 13MHz clock earlier for clocksource
clk: Add missing documentation of devm_clk_bulk_get_optional() argument
clk: at91: generated: Truncate divisor to GENERATED_MAX_DIV + 1
Add a pool of flow counters, based on flow counter bulks, removing the
need to allocate a new counter via a costly FW command during the flow
creation process. The time it takes to acquire/release a flow counter
is cut from ~50 [us] to ~50 [ns].
The pool is part of the mlx5 driver instance, and provides flow
counters for aging flows. mlx5_fc_create() was modified to provide
counters for aging flows from the pool by default, and
mlx5_destroy_fc() was modified to release counters back to the pool
for later reuse. If bulk allocation is not supported or fails, and for
non-aging flows, the fallback behavior is to allocate and free
individual counters.
The pool is comprised of three lists of flow counter bulks, one of
fully used bulks, one of partially used bulks, and one of unused
bulks. Counters are provided from the partially used bulks first, to
help limit bulk fragmentation.
The pool maintains a threshold, and strives to maintain the amount of
available counters below it. The pool is increased in size when a
counter acquisition request is made and there are no available
counters, and it is decreased in size when the last counter in a bulk
is released and there are more available counters than the threshold.
All pool size changes are done in the context of the
acquiring/releasing process.
The value of the threshold is directly correlated to the amount of
used counters the pool is providing, while constrained by a hard
maximum, and is recalculated every time a bulk is allocated/freed.
This ensures that the pool only consumes large amounts of memory for
available counters if the pool is being used heavily. When fully
populated and at the hard maximum, the buffer of available counters
consumes ~40 [MB].
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Misc updates from mlx5-next branch.
1) Eli improves the handling of the support for QoS element type
2) Gavi refactors and prepares mlx5 flow counters for bulk allocation
support
3) Parav, refactors and improves E-Switch load/unload flows
4) Saeed, two misc cleanups
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Check if firmware supports the requested element type before
attempting to create the element type.
In addition, explicitly specify the request element type and tsar type.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
First reserved field is off by one instead of reserved_at_1 it should be
reserved_at_2, fix that.
Fixes: a12ff35e0f ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a handle to invoke the new FW capability of allocating a bulk of
flow counters.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards introducing the ability to allocate bulks of flow counters,
refactor the flow counter bulk query process, removing functions and
structs whose names indicated being used for flow counter bulk
allocation FW commands, despite them actually only being used to
support bulk querying, and migrate their functionality to correctly
named functions in their natural location, fs_counters.c.
Additionally, optimize the bulk query process by:
* Extracting the memory used for the query to mlx5_fc_stats so
that it is only allocated once, and not for each bulk query.
* Querying all the counters in one function call.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Fix the request of active low GPIO line events.
- Don't issue WARN() stuff on NULL descriptors if
the GPIOLIB is disabled.
- Preserve the descriptor flags when setting the
initial direction on lines.
-----BEGIN PGP SIGNATURE-----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=2Uyx
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Three GPIO fixes, all touching the core, so quite important:
- Fix the request of active low GPIO line events.
- Don't issue WARN() stuff on NULL descriptors if the GPIOLIB is
disabled.
- Preserve the descriptor flags when setting the initial direction on
lines"
* tag 'gpio-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: Preserve desc->flags when setting state
gpio: don't WARN() on NULL descs if gpiolib is disabled
gpiolib: fix incorrect IRQ requesting of an active-low lineevent
Instead of always calling xen_destroy_contiguous_region() in case the
memory is DMA-able for the used device, do so only in case it has been
made DMA-able via xen_create_contiguous_region() before.
This will avoid a lot of xen_destroy_contiguous_region() calls for
64-bit capable devices.
As the memory in question is owned by swiotlb-xen the PG_owner_priv_1
flag of the first allocated page can be used for remembering.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
* lots more HE (802.11ax) support, particularly things
relevant for the the AP side, but also mesh support
* debugfs cleanups from Greg
* some more work on extended key ID
* start using genl parallel_ops, as preparation for
weaning ourselves off RTNL and getting parallelism
* various other changes all over
-----BEGIN PGP SIGNATURE-----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=eUnh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a reasonably large number of changes:
* lots more HE (802.11ax) support, particularly things
relevant for the the AP side, but also mesh support
* debugfs cleanups from Greg
* some more work on extended key ID
* start using genl parallel_ops, as preparation for
weaning ourselves off RTNL and getting parallelism
* various other changes all over
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fwd_cnt and last_fwd_cnt are protected by rx_lock, so we should use
the same spinlock also if we are in the TX path.
Move also buf_alloc under the same lock.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce the number of credit update messages,
we send them only when the space available seen by the
transmitter is less than VIRTIO_VSOCK_MAX_PKT_BUF_SIZE.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since virtio-vsock was introduced, the buffers filled by the host
and pushed to the guest using the vring, are directly queued in
a per-socket list. These buffers are preallocated by the guest
with a fixed size (4 KB).
The maximum amount of memory used by each socket should be
controlled by the credit mechanism.
The default credit available per-socket is 256 KB, but if we use
only 1 byte per packet, the guest can queue up to 262144 of 4 KB
buffers, using up to 1 GB of memory per-socket. In addition, the
guest will continue to fill the vring with new 4 KB free buffers
to avoid starvation of other sockets.
This patch mitigates this issue copying the payload of small
packets (< 128 bytes) into the buffer of last packet queued, in
order to avoid wasting memory.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
This should apply to all stable kernels.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that page_offset is referenced through accessors, remove
the union, and use bv_offset.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb_frag_off(), skb_frag_off_add(), skb_frag_off_set(),
and skb_frag_off_copy() accessors for page_offset.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the locking around nouveau's use of the hmm_range_* APIs. It works
correctly in the success case, but many of the the edge cases have missing
unlocks or double unlocks.
-----BEGIN PGP SIGNATURE-----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=ZdrW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull HMM fixes from Jason Gunthorpe:
"Fix the locking around nouveau's use of the hmm_range_* APIs. It works
correctly in the success case, but many of the the edge cases have
missing unlocks or double unlocks.
The diffstat is a bit big as Christoph did a comprehensive job to move
the obsolete API from the core header and into the driver before
fixing its flow, but the risk of regression from this code motion is
low"
* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
nouveau: unlock mmap_sem on all errors from nouveau_range_fault
nouveau: remove the block parameter to nouveau_range_fault
mm/hmm: move hmm_vma_range_done and hmm_vma_fault to nouveau
mm/hmm: always return EBUSY for invalid ranges in hmm_range_{fault,snapshot}
Commit 33ec3e53e7 ("loop: Don't change loop device under exclusive
opener") made LOOP_SET_FD ioctl acquire exclusive block device reference
while it updates loop device binding. However this can make perfectly
valid mount(2) fail with EBUSY due to racing LOOP_SET_FD holding
temporarily the exclusive bdev reference in cases like this:
for i in {a..z}{a..z}; do
dd if=/dev/zero of=$i.image bs=1k count=0 seek=1024
mkfs.ext2 $i.image
mkdir mnt$i
done
echo "Run"
for i in {a..z}{a..z}; do
mount -o loop -t ext2 $i.image mnt$i &
done
Fix the problem by not getting full exclusive bdev reference in
LOOP_SET_FD but instead just mark the bdev as being claimed while we
update the binding information. This just blocks new exclusive openers
instead of failing them with EBUSY thus fixing the problem.
Fixes: 33ec3e53e7 ("loop: Don't change loop device under exclusive opener")
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PC Engines APU got one fix for software dependencies to automatically load them
and another fix for mapping of key button in the front to issue restart event.
OLPC driver is now can be probed automatically based on module device table.
Intel PMC core driver supports Intel Ice Lake NNPI processor.
WMI driver missed description of new field in the structure that has been added.
The following is an automated git shortlog grouped by driver:
intel_pmc_core:
- Add ICL-NNPI support to PMC Core
pcengines-apuv2:
- use KEY_RESTART for front button
- Fix softdep statement
OLPC:
- add SPI MODULE_DEVICE_TABLE
wmi:
- add missing struct parameter description
-----BEGIN PGP SIGNATURE-----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=3TVg
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.3-3' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"Business as usual, a few fixes and new IDs:
- PC Engines APU got one fix for software dependencies to
automatically load them and another fix for mapping of key button
in the front to issue restart event.
- OLPC driver is now probed automatically based on module device
table.
- Intel PMC core driver supports Intel Ice Lake NNPI processor.
- WMI driver missed description of a new field in the structure that
has been added"
* tag 'platform-drivers-x86-v5.3-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: pcengines-apuv2: use KEY_RESTART for front button
platform/x86: intel_pmc_core: Add ICL-NNPI support to PMC Core
Platform: OLPC: add SPI MODULE_DEVICE_TABLE
platform/x86: wmi: add missing struct parameter description
platform/x86: pcengines-apuv2: Fix softdep statement
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HE allows peers to negotiate the aggregation fragmentation level to be used
during transmission. The level can be 1-3. The Ext element is added behind
the ADDBA request inside the action frame. The responder will then reply
with the same level or a lower one if the requested one is not supported.
This patch only handles the negotiation part as the ADDBA frames get passed
to the ATH11k firmware, which does the rest of the magic for us aswell as
generating the requests.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190729104512.27615-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes mentioned that the comment should not reference mac80211 as other
subsystems might call the helper.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
Cc: stable@vger.kernel.org
Reported-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for the fair scheduling class:
- Prevent freeing memory which is accessible by concurrent readers
- Make the RCU annotations for numa groups consistent"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Use RCU accessors consistently for ->numa_group
sched/fair: Don't free p->numa_faults with concurrent readers
The Tegra EQOS driver already resets the MDIO bus at probe time via the
reset GPIO specified in the phy-reset-gpios device tree property. There
is no need to reset the bus again later on.
This avoids the need to query the device tree for the snps,reset GPIO,
which is not part of the Tegra EQOS device tree bindings. This quiesces
an error message from the generic bus reset code if it doesn't find the
snps,reset related delays.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix mismatches in $id values and actual filenames. Now checked by
tools.
- Convert nvmem binding to DT schema
- Fix a typo in of_property_read_bool() kerneldoc
- Remove some redundant description in al-fic interrupt-controller
-----BEGIN PGP SIGNATURE-----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=ozkP
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"The nvmem changes would typically go thru Greg's tree, but they were
missed in the merge window. [ Acked by Greg ]
Summary:
- Fix mismatches in $id values and actual filenames. Now checked by
tools.
- Convert nvmem binding to DT schema
- Fix a typo in of_property_read_bool() kerneldoc
- Remove some redundant description in al-fic interrupt-controller"
* tag 'devicetree-fixes-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Fix more $id value mismatches filenames
dt-bindings: nvmem: SID: Fix the examples node names
dt-bindings: nvmem: Add YAML schemas for the generic NVMEM bindings
of: Fix typo in kerneldoc
dt-bindings: interrupt-controller: al-fic: remove redundant binding
dt-bindings: clk: allwinner,sun4i-a10-ccu: Correct path in $id
- Fix duplicate device_unregister() calls (multiple threads competing to
do unregister work when scheduling device removal from a sysfs attribute
of the self-same device).
- Fix badblocks registration order bug. Ensure region badblocks are
initialized in advance of namespace registration.
- Fix a deadlock between the bus lock and probe operations.
- Export device-core infrastructure to coordinate async operations via
the device ->dead state.
- Add device-core infrastructure to validate device_lock() usage with
lockdep.
-----BEGIN PGP SIGNATURE-----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=mhIp
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A collection of locking and async operations fixes for v5.3-rc2. These
had been soaking in a branch targeting the merge window, but missed
due to a regression hunt. This fixed up version has otherwise been in
-next this past week with no reported issues.
In order to gain confidence in the locking changes the pull also
includes a debug / instrumentation patch to enable lockdep coverage
for libnvdimm subsystem operations that depend on the device_lock for
exclusion. As mentioned in the changelog it is a hack, but it works
and documents the locking expectations of the sub-system in a way that
others can use lockdep to verify. The driver core touches got an ack
from Greg.
Summary:
- Fix duplicate device_unregister() calls (multiple threads competing
to do unregister work when scheduling device removal from a sysfs
attribute of the self-same device).
- Fix badblocks registration order bug. Ensure region badblocks are
initialized in advance of namespace registration.
- Fix a deadlock between the bus lock and probe operations.
- Export device-core infrastructure to coordinate async operations
via the device ->dead state.
- Add device-core infrastructure to validate device_lock() usage with
lockdep"
* tag 'libnvdimm-fixes-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
driver-core, libnvdimm: Let device subsystems add local lockdep coverage
libnvdimm/bus: Fix wait_nvdimm_bus_probe_idle() ABBA deadlock
libnvdimm/bus: Stop holding nvdimm_bus_list_mutex over __nd_ioctl()
libnvdimm/bus: Prepare the nd_ioctl() path to be re-entrant
libnvdimm/region: Register badblocks before namespaces
libnvdimm/bus: Prevent duplicate device_unregister() calls
drivers/base: Introduce kill_device()
"Findfrom" is not a word. Replace the function synopsis by something
that makes sense.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl06EYUACgkQSD+KveBX
+j7R4QgAht/C4115mi1Tc3d3zYjHp3SWLFxwK4vF0U2j30ouhsj1oaIP8bQdw6Mr
6hS4IZSdKNO5wo+NNqMnLYVtsAnvNGOuvYwUvMK5TDkdDb2lIzRlxihpWgTqWzXr
6Eh3nv5rTItgLMqxbLL1EE8Idlx3HQDJtU2a/AmxjmU/TqSKzbBTpnKIlRMPDFNC
PLWXjFXBR/XtcTbsnj7RtlD2HkDAERVTiMP2mlTvXjXxlN56YXCle4CWZamgH9H4
bTCrZwQHH9hllMAnAkq4gpHN7Z6/eXjV6jzu+BOE7ChOaEC5N2F+p5ARXqe+HwRL
apMYgRH5u4mzDt+1CbwR/I/pFOw3WA==
=NXce
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-07-25
This series introduces some fixes to mlx5 driver.
1) Ariel is addressing an issue with enacp flow counter race condition
2) Aya fixes ethtool speed handling
3) Edward fixes modify_cq hw bits alignment
4) Maor fixes RDMA_RX capabilities handling
5) Mark reverses unregister devices order to address an issue with LAG
6) From Tariq,
- wrong max num channels indication regression
- TLS counters naming and documentation as suggested by Jakub
- kTLS, Call WARN_ONCE on netdev mismatch
There is one patch in this series that touches nfp driver to align
TLS statistics names with latest documentation, Jakub is CC'ed.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5: Use reversed order when unregister devices')
For -stable v4.20
('net/mlx5e: Prevent encap flow counter update async to user query')
('net/mlx5: Fix modify_cq_in alignment')
For -stable v5.1
('net/mlx5e: Fix matching of speed to PRM link modes')
For -stable v5.2
('net/mlx5: Add missing RDMA_RX capabilities')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.
However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.
In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.
Fixes: 5eb5f8608e ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=HIzH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190726' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Several io_uring fixes/improvements:
- Blocking fix for O_DIRECT (me)
- Latter page slowness for registered buffers (me)
- Fix poll hang under certain conditions (me)
- Defer sequence check fix for wrapped rings (Zhengyuan)
- Mismatch in async inc/dec accounting (Zhengyuan)
- Memory ordering issue that could cause stall (Zhengyuan)
- Track sequential defer in bytes, not pages (Zhengyuan)
- NVMe pull request from Christoph
- Set of hang fixes for wbt (Josef)
- Redundant error message kill for libahci (Ding)
- Remove unused blk_mq_sched_started_request() and related ops (Marcos)
- drbd dynamic alloc shash descriptor to reduce stack use (Arnd)
- blkcg ->pd_stat() non-debug print (Tejun)
- bcache memory leak fix (Wei)
- Comment fix (Akinobu)
- BFQ perf regression fix (Paolo)
* tag 'for-linus-20190726' of git://git.kernel.dk/linux-block: (24 commits)
io_uring: ensure ->list is initialized for poll commands
Revert "nvme-pci: don't create a read hctx mapping without read queues"
nvme: fix multipath crash when ANA is deactivated
nvme: fix memory leak caused by incorrect subsystem free
nvme: ignore subnqn for ADATA SX6000LNP
drbd: dynamically allocate shash descriptor
block: blk-mq: Remove blk_mq_sched_started_request and started_request
bcache: fix possible memory leak in bch_cached_dev_run()
io_uring: track io length in async_list based on bytes
io_uring: don't use iov_iter_advance() for fixed buffers
block: properly handle IOCB_NOWAIT for async O_DIRECT IO
blk-mq: allow REQ_NOWAIT to return an error inline
io_uring: add a memory barrier before atomic_read
rq-qos: use a mb for got_token
rq-qos: set ourself TASK_UNINTERRUPTIBLE after we schedule
rq-qos: don't reset has_sleepers on spurious wakeups
rq-qos: fix missed wake-ups in rq_qos_throttle
wait: add wq_has_single_sleeper helper
block, bfq: check also in-flight I/O in dispatch plugging
block: fix sysfs module parameters directory path in comment
...
Including:
- Revert an Intel VT-d patch that caused boot problems on some
machines
- Fix AMD IOMMU interrupts with x2apic enabled
- Fix a potential crash when Intel VT-d domain allocation fails
- Fix crash in Intel VT-d driver when accessing a domain without
a flush queue
- Formatting fix for new Intel VT-d debugfs code
- Fix for use-after-free bug in IOVA code
- Fix for a NULL-pointer dereference in Intel VT-d driver when
PCI hotplug is used
- Compilation fix for one of the previous fixes
-----BEGIN PGP SIGNATURE-----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=F+hM
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- revert an Intel VT-d patch that caused boot problems on some machines
- fix AMD IOMMU interrupts with x2apic enabled
- fix a potential crash when Intel VT-d domain allocation fails
- fix crash in Intel VT-d driver when accessing a domain without a
flush queue
- formatting fix for new Intel VT-d debugfs code
- fix for use-after-free bug in IOVA code
- fix for a NULL-pointer dereference in Intel VT-d driver when PCI
hotplug is used
- compilation fix for one of the previous fixes
* tag 'iommu-fixes-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Add support for X2APIC IOMMU interrupts
iommu/iova: Fix compilation error with !CONFIG_IOMMU_IOVA
iommu/vt-d: Print pasid table entries MSB to LSB in debugfs
iommu/iova: Remove stale cached32_node
iommu/vt-d: Check if domain->pgd was allocated
iommu/vt-d: Don't queue_iova() if there is no flush queue
iommu/vt-d: Avoid duplicated pci dma alias consideration
Revert "iommu/vt-d: Consolidate domain_init() to avoid duplication"
Add support to mac80211 for parsing SPR elements as per
P802.11ax_D4.0 section 9.4.2.241.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190618061915.7102-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-07-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix segfault in libbpf, from Andrii.
2) fix gso_segs access, from Eric.
3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.
The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.
Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.
This causes wrong stats presentation of encapsulation flows to user.
Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.
Fixes: f6dfb4c3f2 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters")
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix modify_cq_in alignment to match the device specification.
After this fix the 'cq_umem_valid' field will be in the right offset.
Cc: <stable@vger.kernel.org> # 4.19
Fixes: bd37197554 ("net/mlx5: Update mlx5_ifc with DEVX UID bits")
Signed-off-by: Edward Srouji <edwards@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
These two functions are marked as a legacy APIs to get rid of, but seem to
suit the current nouveau flow. Move it to the only user in preparation
for fixing a locking bug involving caller and callee. All comments
referring to the old API have been removed as this now is a driver private
helper.
Link: https://lore.kernel.org/r/20190724065258.16603-3-hch@lst.de
Tested-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
DIM causes to the following warnings during kernel compilation
which indicates that tx_profile and rx_profile are supposed to
be declared in *.c and not in *.h files.
In file included from ./include/rdma/ib_verbs.h:64,
from ./include/linux/mlx5/device.h:37,
from ./include/linux/mlx5/driver.h:51,
from ./include/linux/mlx5/vport.h:36,
from drivers/infiniband/hw/mlx5/ib_virt.c:34:
./include/linux/dim.h:326:1: warning: _tx_profile_ defined but not used [-Wunused-const-variable=]
326 | tx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
| ^~~~~~~~~~
./include/linux/dim.h:320:1: warning: _rx_profile_ defined but not used [-Wunused-const-variable=]
320 | rx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
| ^~~~~~~~~~
Fixes: 4f75da3666 ("linux/dim: Move implementation to .c files")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a description for the context parameter in the struct wmi_device_id.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: a48e23385f ("platform/x86: wmi: add context pointer field to struct wmi_device_id")
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The access() (and faccessat()) credentials change can cause an
unnecessary load on the RCU machinery because every access() call ends
up freeing the temporary access credential using RCU.
This isn't really noticeable on small machines, but if you have hundreds
of cores you can cause huge slowdowns due to RCU storms.
It's easy to avoid: the temporary access crededntials aren't actually
normally accessed using RCU at all, so we can avoid the whole issue by
just marking them as such.
* access-creds:
access: avoid the RCU grace period for the temporary subjective credentials
The old code used RCU annotations and accessors inconsistently for
->numa_group, which can lead to use-after-frees and NULL dereferences.
Let all accesses to ->numa_group use proper RCU helpers to prevent such
issues.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Fixes: 8c8a743c50 ("sched/numa: Use {cpu, pid} to create task groups for shared faults")
Link: https://lkml.kernel.org/r/20190716152047.14424-3-jannh@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
