Free memory mapping, if hdmi_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These updates:
* improve the robustness of the driver wrt races
* improve the compliance for sending infoframes and audio
* re-organise the function order in the driver to group like functions
together. (This unfortunately causes a conflict with the change in
drm-misc, but it should be trivial to solve, although it looks more
scarey than it really is - sfr has already sent two reports about
this, one earlier today.)
* simplify tda998x_audio_get_eld and DPMS handling
* power down sections of the chip that we never use
* add some initial preparation for supporting the CEC driver
* 'drm-tda998x-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix spelling mistake
drm/i2c: tda998x: allow sharing of the CEC device accesses
drm/i2c: tda998x: allow interrupt to be shared
drm/i2c: tda998x: power down pre-filter and color conversion
drm/i2c: tda998x: switch to boolean is_on
drm/i2c: tda998x: remove complexity from tda998x_audio_get_eld()
drm/i2c: tda998x: group audio functions together
drm/i2c: tda998x: separate connector initialisation
drm/i2c: tda998x: group connector functions and funcs together
drm/i2c: tda998x: move and rename tda998x_encoder_set_config()
drm/i2c: tda998x: correct function name in comments
drm/i2c: tda998x: only enable audio if supported by sink
drm/i2c: tda998x: only configure infoframes and audio if supported
drm/i2c: tda998x: avoid race when programming audio
drm/i2c: tda998x: avoid racy access to mode clock
drm/i2c: tda998x: avoid race in tda998x_encoder_mode_set()
drm/i2c: tda998x: move audio mutex initialisation
Building on top of the MALI change previously merged, these changes:
* add tracing support for overlay updates
* refactor some of the plane support code
* de-midlayer the driver
* cleanups from other folk reviewing the code
* 'drm-armada-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/armada: fix NULL pointer comparison warning
drm/armada: use DRM_FB_HELPER_DEFAULT_OPS for fb_ops
drm/armada: remove some dead code
drm/armada: mark symbols static where possible
drm/armada: de-midlayer armada
drm/armada: use common helper for plane base address
drm/armada: move setting primary plane position to armada_drm_primary_set()
drm/armada: split out primary plane update
drm/armada: move plane state to struct armada_plane
drm/armada: clean up armada_drm_plane_work_run()
drm/armada: add tracing support
Some monitors will have noise or even no sound after
applying the patch 6014ac12.
In patch 6014ac12, it will reset the cts value to 0 for HDMI.
However, we need to disable Enable CTS or M Prog bit. This is
the initial setting after HW reset.
Fixes: 6014ac122e ("drm/i915/audio: set proper N/M in modeset")
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478853988-139842-1-git-send-email-libin.yang@intel.com
As i915.enable_cmd_parser is an unsafe option, make it read-only at
runtime. Now that it is constant, we can use the value determined during
initialisation as to whether we need the cmdparser at execbuffer time.
v2: Remove the inline for its single user, it is clear enough (and
shorter) without!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124125851.6615-1-chris@chris-wilson.co.uk
The i915_next_seqno read value is to be the next seqno used by the
kernel. However, in the conversion to atomics ops for gt.next_seqno, in
commit 28176ef4cf ("drm/i915: Reserve space in the global seqno during
request allocation"), this was changed from a post-increment to a
pre-increment. This increment was missed from the value reported by
debugfs, so in effect it was reporting the current seqno (last
assigned), not the next seqno.
Fixes: 28176ef4cf ("drm/i915: Reserve space in the global seqno during request allocation")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81209
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124094752.19129-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
No sense in keeping the cmd_descriptor and cmd_table structs in
i915_drv.h, now that they are no longer referenced externally.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479942147-9837-1-git-send-email-matthew.auld@intel.com
Doing cmd_header >> 29 to extract our 3-bit client value where we know
cmd_header is a u32 shouldn't then also require the use of a mask. So
remove the redundant operation and get rid of INSTR_CLIENT_MASK now that
there are no longer any users.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479163174-29686-1-git-send-email-matthew.auld@intel.com
i915_hws_info() has not been kept upto date (missing new engines) and so
I consider it to be unused. HWS is included in the error state, which
would be an avenue to retrieving it if required in future (possibly via
i915_engine_info). As it is currently oopsing with an rpm testcase, just
remove it.
Fixes: 3b3f1650b1 ("drm/i915: Allocate intel_engine_cs structure only for the enabled engines")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98838
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124093401.18852-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
Use the color_adjust callback when reserving a node to check if
inserting a node into this hole requires any additional space, and so if
that space then conflicts with an existing allocation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161123141118.23876-2-chris@chris-wilson.co.uk
Some clients would like to iterate over every node within a certain
range. Make a nice little macro for them to hide the mixing of the
rbtree search and linear walk.
v2: Blurb
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161123141118.23876-1-chris@chris-wilson.co.uk
The probe function requests the interrupt before initializing
the ddp component. Which leads to a null pointer dereference at boot.
Fix this by requesting the interrput after all components got
initialized properly.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC
MT8173.")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Change-Id: I57193a7ab554dfb37c35a455900689333adf511c
Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e.
Tlpx, Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP
mode, those signals will cause h-time larger than normal and reduce FPS.
So need to multiply a coefficient to offset the extra signal's effect.
coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+
Ths_trail+Ths_exit)/(htotal*bpp/lane_number)
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
If we want to set the hardware OD to relay mode,
we have to set DISP_OD_CFG register rather than
OD_RELAYMODE; otherwise, the system will access
the wrong address.
Change-Id: Ifb9bb4caa63df906437d48b5d5326b6d04ea332a
Fixes: 7216436420 ("drm/mediatek: set mt8173 dithering function")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
For 64bit bar while reading the higher 32bit the value should be returned
directly.
In the current implementation the higher 32bit value was discarded and not
written to the cfg space of vgpu which lead to an incorrect bar size.
Signed-off-by: Xiaoguang Chen <xiaoguang.chen@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
A late issue discovered by Russell King while testing his setup on Juno.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm/arm: hdlcd: fix plane base address update
one small powerplay fix and one regression fix for older PX systems and d3cold
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix power state when port pm is unavailable (v2)
drm/amdgpu: fix power state when port pm is unavailable
drm/amd/powerplay: avoid out of bounds access on array ps.
In all cases we can now obtain the relevant crtc_state/conn_state
from the relevant callbacks, which means all the ->config accesses
can be removed and the code cleaned up.
Changes since v1:
- cstate -> crtc_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8b02a6b4-606a-e43a-b357-ad17f491525b@linux.intel.com
[mlankhorst: Reinstate missing comment]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
A modeset on one pipe can update dev_priv->atomic_cdclk_freq without
actually touching the hardware, in which case we won't force a modeset
on all the pipes, and thus won't lock any of the other pipes either.
That means a parallel plane update on another pipe could be looking at
a stale dev_priv->atomic_cdcdlk_freq and thus fail to notice when the
plane configuration is invalid, or potentially reject a valid update.
To overcome this we must protect writes to atomic_cdclk_freq with
all the crtc locks, and thus for reads any single crtc lock will
be sufficient protection.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479141311-11904-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we end up not recomputing the cdclk, we need to populate
intel_state->cdclk with the "atomic_cdclk_freq" instead of the
current cdclk_freq. When no pipes are active, the actual cdclk_freq
may be lower than what the configuration of the planes and
pipes would require from the point of view of the software state.
This fixes bogus WARNS from skl_max_scale() which is trying to check
the plane software state against the cdclk frequency. So any time
it got called during DPMS off for instance, we might have tripped
the warn if the current mode would have required a higher than
minimum cdclk.
v2: Drop the dev_cdclk stuff (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: bruno.pagani@ens-lyon.org
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Joseph Yasi <joe.yasi@gmail.com> (v1)
Cc: stable@vger.kernel.org
Fixes: 1a617b7765 ("drm/i915: Keep track of the cdclk as if all crtc's were active.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98214
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479141311-11904-2-git-send-email-ville.syrjala@linux.intel.com
UVD 5 and newer do not have the same placement limitations
as older chips, so skip the first pass since it's just
overhead on chips where we don't have to force placement.
v2: fix inverted logic
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same code duplicated in both functions.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is used for virtualization support. In virtualization,
only SMU manager is needed, DPM should be disabled. This is a
use case for commit 2f9346b6f984
("drm/amdgpu/powerplay: pp module only enable smu when dpm disabled.")
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doesn't make much sense to have the same functionality twice.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop this whole reserve/unreserve dance, just lock the
reservation object manually when creating the BO.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Manually checking why a function could fail is not a good idea
if you can just check the functions return code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mem start is relative to the domain in the address space, so this
worked only when VRAM was mapped at offset 0.
It also didn't handled multiple drm_mm_nodes for split VRAM.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It can be the case that upon GPU page faults we start trashing
the logs, and so let us ratelimit here to avoid that.
V2. Fix issue where calling dev_err_ratelimited separately for
each line means that some lines corresponding to a single
VM fault may or may not appear depending on the rate.
- Michel Dänzer.
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Port of SI DCE v6 over to new AMDGPU headers. Tested on a
Tahiti with GNOME through various hot plugs/rotations/sizes/fullscreen/windowed and
staging drm/xf86-video-amdgpu.
(v2) Re-factored to remove formatting changes to si_enums.h
as well rename various defines.
(v3) Rebase on upstream
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when shadowing enabled, tesselation app will trigger
vm fault because below three tesselation registers:
VGT_TF_RING_SIZE__CI__VI,
VGT_HS_OFFCHIP_PARAM__CI__VI,
VGT_TF_MEMORY_BASE__CI__VI,
need to be programed after vgt-flush.
Tesselation picture vm fault disappeared after vgt-flush
introduced.
v2:implement vgt-flush for CI & SI.
v3:move vgt flush inside of cntx_cntrl
v4:count vgt flush in frame_size
v5:squash in typo fix
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sw clockgate was used on uvd6.0.
when uvd is idle, we gate the uvd clock.
when decode, we ungate the uvd clock.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Let's try not to abuse plane->plane for sprites on VLV/CHV and instead
use plane->id. Since out watermark structures aren't entirely plane type
agnostic (for now) and start indexing sprites from 0 we'll add a small
helper to convert between the two bases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-7-git-send-email-ville.syrjala@linux.intel.com
Use intel_plane->id to derive the VLV/CHV sprite register offsets
instead of abusing plane->plane which is really meant to for
primary planes only.
v2: Convert assert_sprites_disabled() over as well
v3: Rename the reg macro parameter to 'plane_id' as well (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-6-git-send-email-ville.syrjala@linux.intel.com
Replace the intel_plane->plane and hardcoded 0 usage in the SKL plane
code with intel_plane->id.
This should make the SKL "primary" and "sprite" code virtually
identical, so the next logical step would likely be dropping one
of the copies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-5-git-send-email-ville.syrjala@linux.intel.com
Nuke skl_wm_plane_id() and just use the new intel_plane->id.
v2: Convert skl_write_plane_wm() as well
v3: Convert skl_pipe_wm_get_hw_state() correctly
v4: Rebase due to changes in the wm code
Drop the cursor FIXME from the total data rate calc (Paulo)
Use the "[PLANE:%d:%s]" format in debug print (Paulo)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude <cpaul@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Lyude <lyude@redhat.com>
Add a mask of which planes are available for each pipe. This doesn't
quite work for old platforms with dynamic plane<->pipe assignment, but
as we don't support that sort of stuff (yet) we can get away with it.
The main use I have for this is the for_each_plane_id_on_crtc() macro
for iterating over all possible planes on the crtc. I suppose we could
not add the mask, and instead iterate by comparing intel_plane->pipe
but then we'd need a local intel_plane variable which is just
unnecessary clutter in some cases. But I'm not hung up on this, so if
people prefer the other option I could be convinced to use it.
v2: Use BIT() in the iterator macro too (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-3-git-send-email-ville.syrjala@linux.intel.com
As I told people in [1] we really should not be confusing enum plane
as a per-pipe plane identifier. Looks like that happened nonetheless, so
let's fix it up by splitting the two into two enums.
We'll also want something we just directly pass to various register
offset macros and whatnot on SKL+. So let's make this new thing work for that.
Currently we pass intel_plane->plane for the "sprites" and just a
hardcoded zero for the "primary" planes. We want to get rid of that
hardocoding so that we can share the same code for all planes (apart
from the legacy cursor of course).
[1] https://lists.freedesktop.org/archives/intel-gfx/2015-September/076082.html
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-2-git-send-email-ville.syrjala@linux.intel.com
Someone forgot to make skl_write_{plane,cursor}_wm() static when
removing the prototypes from the header. Sparse isn't pleased.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: e62929b3f6 ("drm/i915/gen9+: Program watermarks as a separate step during evasion, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479846113-24745-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Lyude <lyude@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
v2: agd: fix typo
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Reported-and-tested-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
