Somehow, firmware could report invalid TX rate, and we consider the
invalid rate as 0 that will make a wrong decision. So, drop invalid
reports, and also suppress the warning message.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-9-pkshih@realtek.com
Some warning messages could bother users. With proper handling, these
situations don't really affect usage, but we still need to keep monitor
these messages. If they happen frequently, we must review driver or
hardware design to clarify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-8-pkshih@realtek.com
To improve VO throughput, we enable VO TX AMPDU.
We measure the latency of enable or disable VO TX AMPDU. The experimental
results show that the difference between the two is insignificant only
300µs, so the little impact can be ignored for user experience.
Moreover, we found some APs will have a group key handshake timeout issue
when the EAPOL's TID is already setup BA session. Therefore, when
transmitting EAPOL, if EAPOL's TID BA session is already setup, we need
to delete it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-7-pkshih@realtek.com
The potential TX stuck occurs when there are lots of packets to be
transmitted and the boundary of the tx_resource is hit. Add this
patch to avoid the TX stuck when burst traffic.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-6-pkshih@realtek.com
In STA mode, if peer is TDLS. Allocate a BSSID CAM entry with peer's
address to match address properly, and then hardware can ACK peer's
packets and receive packets to driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-4-pkshih@realtek.com
Normally, we allocate a BSSID CAM to a vif. By hardware design, we must
allocate a BSSID CAM to each TDLS peer, so separate BSSID CAM operations
that will be used by later patches.
This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-3-pkshih@realtek.com
Normally, we only allocate an address CAM and single one MAC ID to AP in
STA mode. To support TDLS, we handle TDLS peers like AP handles stations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-2-pkshih@realtek.com
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com
The sc7180-trogdor-{lazor,homestar}-*.dtsi files all include
sc7180-trogdor.dtsi and sc7180-trogdor-lazor.dtsi or
sc7180-trogdor-homestar.dtsi, so including it here in the
sc7180-trogdor-{lazor,homestar}.dtsi file means we have a duplicate
include after commit 19794489fa ("arm64: dts: qcom: Only include
sc7180.dtsi in sc7180-trogdor.dtsi"). We include the sc7180-trogdor.dtsi
file in a board like sc7180-trogdor-lazor-r1.dts so that we can include
the display bridge snippet (e.g. sc7180-trogdor-ti-sn65dsi86.dtsi)
instead of making ever increasing variants like
sc7180-trogdor-lazor-ti-sn65dsi86.dtsi.
Unfortunately, having the double include like this means the display
bridge's i2c bus is left disabled instead of enabled by the bridge
snippet. Any boards that use the i2c bus for the display bridge will
have the bus disabled when we include sc7180-trogdor.dtsi the second
time, which picks up the i2c status="disabled" line from sc7180.dtsi.
This leads to the display not turning on and black screens at boot on
lazor and homestar devices.
Fix this by dropping the include and making a note that the
sc7180-trogdor-{lazor,homestar}.dtsi file must be included after
sc7180-trogdor.dtsi
Reported-by: Douglas Anderson <dianders@chromium.org>
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Fixes: 19794489fa ("arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220602190621.1646679-1-swboyd@chromium.org
Eduard Zingerman says:
====================
Hi Everyone,
This is the next iteration of the patch. It includes changes suggested
by Song, Joanne and Alexei. Please find updated intro message and
change log below.
This patch implements inlining of calls to bpf_loop helper function
when bpf_loop's callback is statically known. E.g. the rewrite does
the following transformation during BPF program processing:
bpf_loop(10, foo, NULL, 0);
->
for (int i = 0; i < 10; ++i)
foo(i, NULL);
The transformation leads to measurable latency change for simple
loops. Measurements using `benchs/run_bench_bpf_loop.sh` inside QEMU /
KVM on i7-4710HQ CPU show a drop in latency from 14 ns/op to 2 ns/op.
The change is split in five parts:
* Update to test_verifier.c to specify expected and unexpected
instruction sequences. This allows to check BPF program rewrites
applied by e.g. do_mix_fixups function.
* Update to test_verifier.c to specify BTF function infos and types
per test case. This is necessary for tests that load sub-program
addresses to a variable because of the checks applied by
check_ld_imm function.
* The update to verifier.c that tracks state of the parameters for
each bpf_loop call in a program and decides whether it could be
replaced by a loop.
* A set of test cases for `test_verifier` that use capabilities added
by the first two patches to verify instructions produced by inlining
logic.
* Two test cases for `test_prog` to check that possible corner cases
behave as expected.
Additional details are available in commit messages for each patch.
Changes since v7:
- Call to `mark_chain_precision` is added in `loop_flag_is_zero` to
avoid potential issues with state pruning and precision tracking.
- `flags non-zero` test_verifier test case is updated to have two
execution paths reaching `bpf_loop` call, one with flags = 0,
another with flags = 1. Potentially this test case should be able
to show that call to `mark_chain_precision` is necessary in
`loop_flag_is_zero` but not at the moment. Please refer to
discussion for [PATCH bpf-next v7 3/5] for additional details.
- `stack_depth_extra` computation is updated to guarantee that R6, R7
and R8 offsets are always aligned on 8 byte boundary.
- `stack locations for loop vars` test_verifier test case updated to
show that R6, R7, R8 offsets are indeed aligned when function stack
depth is not a multiple of 8.
- I removed Song Liu's ACK from commit message for [PATCH bpf-next v8
4/5] because I updated the patch. (Please let me know if I had to
keep the ACK tag).
Changes since v6:
- Return value of the `optimize_bpf_loop` function is no longer
ignored. This is necessary to properly propagate -ENOMEM error.
Changes since v5:
- Added function `loop_flag_is_zero` to skip a few checks in
`update_loop_inline_state` when loop instruction is not fit for
inline.
Changes since v4:
- Added missing `static` modifier for `update_loop_inline_state` and
`inline_bpf_loop` functions.
- `update_loop_inline_state` updated for better readability.
- Fields `initialized` and `fit_for_inline` of `struct
bpf_loop_inline_state` are changed back from `bool` to bitfields.
- Acks from Song Liu added to comments for patches 1/5, 2/5, 4/5,
5/5.
Changes since v3:
- Function `adjust_stack_depth_for_loop_inlining` is replaced by
function `optimize_bpf_loop`. Function `optimize_bpf_loop` is
responsible for both stack depth adjustment and call instruction
replacement.
- Changes in `do_misc_fixups` are reverted.
- Changes in `adjust_subprog_starts_after_remove` are reverted and
function `adjust_loop_inline_subprogno` is removed. This is
possible because call to `optimize_bpf_loop` is placed before the
dead code removal in `opt_remove_dead_code` (in contrast to the
position of `do_misc_fixups` where inlining was done in v3).
- Field `bpf_insn_aux_data.loop_inline_state` is now a part of
anonymous union at the start of the `bpf_insn_aux_data`.
- Data structure `bpf_loop_inline_state` is simplified to use single
flag field `fit_for_inline` instead of separate fields
`flags_is_zero` & `callback_is_constant`.
- Macro definition `BPF_MAX_LOOPS` is moved from
`include/linux/bpf_verifier.h` to `include/linux/bpf.h` to avoid
include of `include/linux/bpf_verifier.h` in `bpf_iter.c`.
- `inline_bpf_loop` changed back to use array initialization and hard
coded offsets as in v2.
- Style / formatting updates.
Changes since v2:
- fix for `stack_check` test case in `test_progs-no_alu32`, all tests
are passing now;
- v2 3/3 patch is split in three parts:
- kernel changes
- test_verifier changes
- test_prog changes
- updated `inline_bpf_loop` in `verifier.c` to calculate each offset
used in instructions to avoid "magic" numbers;
- removed newline handling logic in `fail_log` branch of
`do_single_test` in `test_verifier.c` to simplify the patch set;
- styling fixes suggested in review for v2 of this patch set.
Changes since v1:
- allow to use SKIP_INSNS in instruction pattern specification in
test_verifier tests;
- fix for a bug in spill offset assignement for loop vars when
bpf_loop is located in a non-main function.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Two new test BPF programs for test_prog selftests checking bpf_loop
behavior. Both are corner cases for bpf_loop inlinig transformation:
- check that bpf_loop behaves correctly when callback function is not
a compile time constant
- check that local function variables are not affected by allocating
additional stack storage for registers spilled by loop inlining
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220620235344.569325-6-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A number of test cases for BPF selftests test_verifier to check how
bpf_loop inline transformation rewrites the BPF program. The following
cases are covered:
- happy path
- no-rewrite when flags is non-zero
- no-rewrite when callback is non-constant
- subprogno in insn_aux is updated correctly when dead sub-programs
are removed
- check that correct stack offsets are assigned for spilling of R6-R8
registers
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220620235344.569325-5-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Calls to `bpf_loop` are replaced with direct loops to avoid
indirection. E.g. the following:
bpf_loop(10, foo, NULL, 0);
Is replaced by equivalent of the following:
for (int i = 0; i < 10; ++i)
foo(i, NULL);
This transformation could be applied when:
- callback is known and does not change during program execution;
- flags passed to `bpf_loop` are always zero.
Inlining logic works as follows:
- During execution simulation function `update_loop_inline_state`
tracks the following information for each `bpf_loop` call
instruction:
- is callback known and constant?
- are flags constant and zero?
- Function `optimize_bpf_loop` increases stack depth for functions
where `bpf_loop` calls can be inlined and invokes `inline_bpf_loop`
to apply the inlining. The additional stack space is used to spill
registers R6, R7 and R8. These registers are used as loop counter,
loop maximal bound and callback context parameter;
Measurements using `benchs/run_bench_bpf_loop.sh` inside QEMU / KVM on
i7-4710HQ CPU show a drop in latency from 14 ns/op to 2 ns/op.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220620235344.569325-4-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The BTF and func_info specification for test_verifier tests follows
the same notation as in prog_tests/btf.c tests. E.g.:
...
.func_info = { { 0, 6 }, { 8, 7 } },
.func_info_cnt = 2,
.btf_strings = "\0int\0",
.btf_types = {
BTF_TYPE_INT_ENC(1, BTF_INT_SIGNED, 0, 32, 4),
BTF_PTR_ENC(1),
},
...
The BTF specification is loaded only when specified.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220620235344.569325-3-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allows to specify expected and unexpected instruction sequences in
test_verifier test cases. The instructions are requested from kernel
after BPF program loading, thus allowing to check some of the
transformations applied by BPF verifier.
- `expected_insn` field specifies a sequence of instructions expected
to be found in the program;
- `unexpected_insn` field specifies a sequence of instructions that
are not expected to be found in the program;
- `INSN_OFF_MASK` and `INSN_IMM_MASK` values could be used to mask
`off` and `imm` fields.
- `SKIP_INSNS` could be used to specify that some instructions in the
(un)expected pattern are not important (behavior similar to usage of
`\t` in `errstr` field).
The intended usage is as follows:
{
"inline simple bpf_loop call",
.insns = {
/* main */
BPF_ALU64_IMM(BPF_MOV, BPF_REG_1, 1),
BPF_RAW_INSN(BPF_LD | BPF_IMM | BPF_DW, BPF_REG_2,
BPF_PSEUDO_FUNC, 0, 6),
...
BPF_EXIT_INSN(),
/* callback */
BPF_ALU64_IMM(BPF_MOV, BPF_REG_0, 1),
BPF_EXIT_INSN(),
},
.expected_insns = {
BPF_ALU64_IMM(BPF_MOV, BPF_REG_1, 1),
SKIP_INSNS(),
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, BPF_PSEUDO_CALL, 8, 1)
},
.unexpected_insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0,
INSN_OFF_MASK, INSN_IMM_MASK),
},
.prog_type = BPF_PROG_TYPE_TRACEPOINT,
.result = ACCEPT,
.runs = 0,
},
Here it is expected that move of 1 to register 1 would remain in place
and helper function call instruction would be replaced by a relative
call instruction.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220620235344.569325-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Some servers do not allow null netname contexts, which would cause
multichannel to revert to single channel when mounting to some
servers (e.g. Azure xSMB).
Fixes: 4c14d7043f ("cifs: populate empty hostnames for extra channels")
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
If a read races with an invalidation followed by another read, it is
possible for a folio to be replaced with a higher-order folio. If that
happens, we'll see a sibling entry for the new folio in the next iteration
of the loop. This manifests as a NULL pointer dereference while holding
the RCU read lock.
Handle this by simply returning. The next call will find the new folio
and handle it correctly. The other ways of handling this rare race are
more complex and it's just not worth it.
Reported-by: Dave Chinner <david@fromorbit.com>
Reported-by: Brian Foster <bfoster@redhat.com>
Debugged-by: Brian Foster <bfoster@redhat.com>
Tested-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Fixes: cbd59c48ae ("mm/filemap: use head pages in generic_file_buffered_read")
Cc: stable@vger.kernel.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
We had an off-by-one error which meant that we never marked the first page
in a read as accessed. This was visible as a slowdown when re-reading
a file as pages were being evicted from cache too soon. In reviewing
this code, we noticed a second bug where a multi-page folio would be
marked as accessed multiple times when doing reads that were less than
the size of the folio.
Abstract the comparison of whether two file positions are in the same
folio into a new function, fixing both of these bugs.
Reported-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
clk_put() already checks the clk ptr using !clk and IS_ERR()
so there is no need to check it again before calling it.
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
clk_disable() already checks the clk ptr using IS_ERR_OR_NULL(clk) and
clk_enable() checks the clk ptr using !clk, so there is no need to check clk
ptr again before calling them.
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Helge Deller <deller@gmx.de>
In pxa3xx_gcu_write, a count parameter of type size_t is passed to words of
type int. Then, copy_from_user() may cause a heap overflow because it is used
as the third argument of copy_from_user().
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
This reverts commit 73867c8709 ("drm/i915/display: Remove check for
low voltage sku for max dp source rate"), which, on an i7-11850H iGPU
with a Thinkpad X1 Extreme Gen 4, attached to a LG LP160UQ1-SPB1
embedded panel, causes wild flickering glitching technicolor
pyrotechnics on resumption from suspend. The display shows strobing
colors in an utter disaster explosion of pantone, as though bombs were
dropped on the leprechauns at the base of the rainbow.
Rebooting the machine fixes the issue, presumably because the display is
initialized by firmware rather than by i915. Otherwise, the GPU appears
to work fine.
Bisection traced it back to this commit, which makes sense given the
issues.
Note: This re-opens, and puts back to the drawing board,
https://gitlab.freedesktop.org/drm/intel/-/issues/5272 which was fixed
by the regressing commit.
Fixes: 73867c8709 ("drm/i915/display: Remove check for low voltage sku for max dp source rate")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6205
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220613102241.9236-1-Jason@zx2c4.com
(cherry picked from commit d592983508)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are some functions that were missed by commit d77e745613 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.
The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.
Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-4-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e745613 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.
But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.
Also is a fragile assumption to make so is better to make it fail earlier.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-3-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e745613 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.
Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-2-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Eight fixes, all in drivers (ufs, scsi_debug, storvsc, iscsi, ibmvfc).
Apart from the ufs command clearing updates, these are mostly minor
and obvious fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYrBbayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQKMAP9WilSW
JKNlEf0HGBvL14QAKoeg7OpF9wzYA6Bzl8h3qwEAlgcudJOdNCspWIHMFWdCnFEV
oe25ZYfLhLazqs4oUsA=
=04cZ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes, all in drivers (ufs, scsi_debug, storvsc, iscsi, ibmvfc).
Apart from the ufs command clearing updates, these are mostly minor
and obvious fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvfc: Store vhost pointer during subcrq allocation
scsi: ibmvfc: Allocate/free queue resource only during probe/remove
scsi: storvsc: Correct reporting of Hyper-V I/O size limits
scsi: ufs: Fix a race between the interrupt handler and the reset handler
scsi: ufs: Support clearing multiple commands at once
scsi: ufs: Simplify ufshcd_clear_cmd()
scsi: iscsi: Exclude zero from the endpoint ID range
scsi: scsi_debug: Fix zone transition to full condition
- Don't set data source if it's not a memory operation in ARM SPE (Statistical
Profiling Extensions).
- Fix handling of exponent floating point values in perf stat expressions.
- Don't leak fd on failure on libperf open.
- Fix 'perf test' CPU topology test for PPC guest systems.
- Fix undefined behaviour on breakpoint account 'perf test' entry.
- Record only user callchains on the "Check ARM64 callgraphs are complete in FP
mode" 'perf test' entry.
- Fix "perf stat CSV output linter" test on s390.
- Sync batch of kernel headers with tools/perf/.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYq93OQAKCRCyPKLppCJ+
Jy0RAQD+B7rvd/4VcbLY7hJkhH4h8C2J4Le59Owq3W8TZTTNDgEAupY1IDPnJlWZ
BxIkcRKh0+aB6tVGMKIASlWs3ugc+wQ=
=Ym7P
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.19-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Don't set data source if it's not a memory operation in ARM SPE
(Statistical Profiling Extensions).
- Fix handling of exponent floating point values in perf stat
expressions.
- Don't leak fd on failure on libperf open.
- Fix 'perf test' CPU topology test for PPC guest systems.
- Fix undefined behaviour on breakpoint account 'perf test' entry.
- Record only user callchains on the "Check ARM64 callgraphs are
complete in FP mode" 'perf test' entry.
- Fix "perf stat CSV output linter" test on s390.
- Sync batch of kernel headers with tools/perf/.
* tag 'perf-tools-fixes-for-v5.19-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
tools headers UAPI: Sync linux/prctl.h with the kernel sources
perf metrics: Ensure at least 1 id per metric
tools headers arm64: Sync arm64's cputype.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf arm-spe: Don't set data source if it's not a memory operation
perf expr: Allow exponents on floating point values
perf test topology: Use !strncmp(right platform) to fix guest PPC comparision check
perf test: Record only user callchains on the "Check Arm64 callgraphs are complete in fp mode" test
perf beauty: Update copy of linux/socket.h with the kernel sources
perf test: Fix variable length array undefined behavior in bp_account
libperf evsel: Open shouldn't leak fd on failure
perf test: Fix "perf stat CSV output linter" test on s390
perf unwind: Fix uninitialized variable
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEjUuTAak14xi+SF7M4CHKc/GJqRAFAmKwXZMACgkQ4CHKc/GJ
qRBZ+gf8C8JlLczNn8oTHZNthCqbe8BENLmI+CdFZ3+Gxijt4XHdS4AEWadcUo2O
m5ZoUNgLiAjChRSZNO4veib5zsERotDhOiOjkG8/ppf0p5WTNY50vQ0McXsndJ9K
IikInusZsyeJrANSi7SeN5vrODP6609SRQiLF+ZH0XrGDvzENHGU8CW0kYU3RsH4
c/Pf8zOMDPkbGsFJk/d/PXgr2dr5hPGz8KOrHI6S5DtY6ODyclx3WaELSGbq7xqz
PubVx2yItQS1nwBQQA9DmE2HZX1lqro50WlJDPDexZft/LBnTosPtdV9E1IC2OK0
JdFim9GClURNXS3xQoZjWFSNocTOvA==
=FgiZ
-----END PGP SIGNATURE-----
Merge tag 'slab-for-5.19-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fixes from Vlastimil Babka:
- A slub fix for PREEMPT_RT locking semantics from Sebastian.
- A slub fix for state corruption due to a possible race scenario from
Jann.
* tag 'slab-for-5.19-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slub: add missing TID updates on slab deactivation
mm/slub: Move the stackdepot related allocation out of IRQ-off section.
Check vm_fault->pgoff before using it. When we removed the warning, we
also removed the check.
Fixes: 7b26e4e211 ("udmabuf: drop WARN_ON() check.")
Reported-by: zdi-disclosures@trendmicro.com
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we mark for reissue, we assume that the buffer will remain stable.
Hence if are using a provided buffer, we need to ensure that we stick
with it for the duration of that request.
This only affects block devices that use provided buffers, as those are
the only ones that get marked with REQ_F_REISSUE.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PCI-specific power management (pci_driver.suspend and pci_driver.resume) is
deprecated. If drivers implement power management, they should use the
generic power management framework, not the PCI-specific hooks.
Convert the sample code to use the generic power management framework.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Helge Deller <deller@gmx.de>
PCI-specific power management (pci_driver.suspend and pci_driver.resume) is
deprecated. The cirrusfb driver has never implemented power management at
all, but if it ever does, it should use the generic power management
framework, not the PCI-specific hooks.
Remove the commented-out references to the PCI-specific power management
hooks.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Helge Deller <deller@gmx.de>
Variable stolen_size can be left uninitialized in a code path with
INTEL_855_GMCH_GMS_DISABLED. Fix this by initializing the variable to 0.
Also fix indentation of function arguments.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Aperture size for i9x5 variants is determined from PCI base address.
if (pci_resource_start(pdev, 2) & 0x08000000)
*aperture_size = MB(128);
...
This condition is incorrect as 128 MiB address can have the address
set as 0x?8000000 or 0x?0000000. Also the code can be simplified to just
use pci_resource_len().
The true settings of the aperture size is in the MSAC register, which
could be used instead. However the value is used only as an info message,
so it doesn't matter.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
This commit adds the kernel config options needed to run the recently
added xdp_synproxy test. Users without these options will hit errors
like this:
test_synproxy:FAIL:iptables -t raw -I PREROUTING -i tmp1 -p
tcp -m tcp --syn --dport 8080 -j CT --notrack unexpected error: 256
(errno 22)
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220620104939.4094104-1-maximmi@nvidia.com
We always allocate skmsg with kzalloc(), so there is no need
to call memset(0) on it, the only thing we need from
sk_msg_init() is sg_init_marker(). So introduce a new helper
which is just kzalloc()+sg_init_marker(), this saves an
unncessary memset(0) for skmsg on fast path.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-5-xiyou.wangcong@gmail.com
With ->read_skb() now we have an entire skb dequeued from
receive queue, now we just need to grab an addtional refcnt
before passing its ownership to recv actors.
And we should not touch them any more, particularly for
skb->sk. Fortunately, skb->sk is already set for most of
the protocols except UDP where skb->sk has been stolen,
so we have to fix it up for UDP case.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-4-xiyou.wangcong@gmail.com
Currently both splice() and sockmap use ->read_sock() to
read skb from receive queue, but for sockmap we only read
one entire skb at a time, so ->read_sock() is too conservative
to use. Introduce a new proto_ops ->read_skb() which supports
this sematic, with this we can finally pass the ownership of
skb to recv actors.
For non-TCP protocols, all ->read_sock() can be simply
converted to ->read_skb().
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-3-xiyou.wangcong@gmail.com
This patch inroduces tcp_read_skb() based on tcp_read_sock(),
a preparation for the next patch which actually introduces
a new sock ops.
TCP is special here, because it has tcp_read_sock() which is
mainly used by splice(). tcp_read_sock() supports partial read
and arbitrary offset, neither of them is needed for sockmap.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-2-xiyou.wangcong@gmail.com
The MLO links used for connection with an MLD AP are decided by the
driver in case of SME offloaded to driver.
Add support for the drivers to indicate the information of links used
for MLO connection in connect and roam callbacks, update the connected
links information in wdev from connect/roam result sent by driver.
Also, send the connected links information to userspace.
Add a netlink flag attribute to indicate that userspace supports
handling of MLO connection. Drivers must not do MLO connection when this
flag is not set. This is to maintain backwards compatibility with older
supplicant versions which doesn't have support for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Print the link ID in link_info_changed function.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add initial support to hwsim for creating MLO-capable
radios dynamically (and statically via module parameter,
but that's not really recommended.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When retrieving scan data, expose not just whether or not the
interface (possibly an MLD) is associated to the BSS or not,
but also on which link ID if it is an MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add to hwsim a link_data structure.
For now, move the beacon interval and beacon timer to
the link_data structure (making them per link).
Set a beacon timer for each link and transmit a per
link beacon (pass the link_id to ieee80211_beacon_get).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should set the STA deflink addresses in case no
link is really added.
Fixes: 046d2e7c50 ("mac80211: prepare sta handling for MLO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maintain a hash table of link-sta addresses so we can find
them for management frames etc. where addresses haven't
been replaced by the drivers to the MLD address yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
