In mlxsw_sp_nexthop6_init(), a next hop is always added to the router
linked list, and mlxsw_sp_nexthop_type_init() is invoked afterwards. When
that function results in an error, the next hop will not have been removed
from the linked list. As the error is propagated upwards and the caller
frees the next hop object, the linked list ends up holding an invalid
object.
A similar issue comes up with mlxsw_sp_nexthop4_init(), where rollback
block does exist, however does not include the linked list removal.
Both IPv6 and IPv4 next hops have a similar issue with next-hop counter
rollbacks. As these were introduced in the same patchset as the next hop
linked list, include the cleanup in this patch.
Fixes: dbe4598c1e ("mlxsw: spectrum_router: Keep nexthops in a linked list")
Fixes: a5390278a5 ("mlxsw: spectrum: Add support for setting counters on nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220629070205.803952-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are UAF bugs in rose_heartbeat_expiry(), rose_timer_expiry()
and rose_idletimer_expiry(). The root cause is that del_timer()
could not stop the timer handler that is running and the refcount
of sock is not managed properly.
One of the UAF bugs is shown below:
(thread 1) | (thread 2)
| rose_bind
| rose_connect
| rose_start_heartbeat
rose_release | (wait a time)
case ROSE_STATE_0 |
rose_destroy_socket | rose_heartbeat_expiry
rose_stop_heartbeat |
sock_put(sk) | ...
sock_put(sk) // FREE |
| bh_lock_sock(sk) // USE
The sock is deallocated by sock_put() in rose_release() and
then used by bh_lock_sock() in rose_heartbeat_expiry().
Although rose_destroy_socket() calls rose_stop_heartbeat(),
it could not stop the timer that is running.
The KASAN report triggered by POC is shown below:
BUG: KASAN: use-after-free in _raw_spin_lock+0x5a/0x110
Write of size 4 at addr ffff88800ae59098 by task swapper/3/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? irq_work_single+0xbb/0x140
? _raw_spin_lock+0x5a/0x110
kasan_report+0xed/0x120
? _raw_spin_lock+0x5a/0x110
kasan_check_range+0x2bd/0x2e0
_raw_spin_lock+0x5a/0x110
rose_heartbeat_expiry+0x39/0x370
? rose_start_heartbeat+0xb0/0xb0
call_timer_fn+0x2d/0x1c0
? rose_start_heartbeat+0xb0/0xb0
expire_timers+0x1f3/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
irq_exit_rcu+0x41/0xa0
sysvec_apic_timer_interrupt+0x8c/0xb0
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1b/0x20
RIP: 0010:default_idle+0xb/0x10
RSP: 0018:ffffc9000012fea0 EFLAGS: 00000202
RAX: 000000000000bcae RBX: ffff888006660f00 RCX: 000000000000bcae
RDX: 0000000000000001 RSI: ffffffff843a11c0 RDI: ffffffff843a1180
RBP: dffffc0000000000 R08: dffffc0000000000 R09: ffffed100da36d46
R10: dfffe9100da36d47 R11: ffffffff83cf0950 R12: 0000000000000000
R13: 1ffff11000ccc1e0 R14: ffffffff8542af28 R15: dffffc0000000000
...
Allocated by task 146:
__kasan_kmalloc+0xc4/0xf0
sk_prot_alloc+0xdd/0x1a0
sk_alloc+0x2d/0x4e0
rose_create+0x7b/0x330
__sock_create+0x2dd/0x640
__sys_socket+0xc7/0x270
__x64_sys_socket+0x71/0x80
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 152:
kasan_set_track+0x4c/0x70
kasan_set_free_info+0x1f/0x40
____kasan_slab_free+0x124/0x190
kfree+0xd3/0x270
__sk_destruct+0x314/0x460
rose_release+0x2fa/0x3b0
sock_close+0xcb/0x230
__fput+0x2d9/0x650
task_work_run+0xd6/0x160
exit_to_user_mode_loop+0xc7/0xd0
exit_to_user_mode_prepare+0x4e/0x80
syscall_exit_to_user_mode+0x20/0x40
do_syscall_64+0x4f/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
This patch adds refcount of sock when we use functions
such as rose_start_heartbeat() and so on to start timer,
and decreases the refcount of sock when timer is finished
or deleted by functions such as rose_stop_heartbeat()
and so on. As a result, the UAF bugs could be mitigated.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Tested-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220629002640.5693-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
This is a usb urb received by "tcpdump -i usbmon2 -X" on a
little-endian CPU:
0x0000: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
^ packet 1 start (pkt_len = 0x05ec)
^^^^ IP alignment pseudo header
^ ethernet packet start
last byte ethernet packet v
padding (8-bytes aligned) vvvv vvvv
0x05e0: c92d d444 1420 8a69 83dd 272f e82b 9811
0x05f0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 2
0x0be0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
...
0x1130: 9d41 9171 8a38 0ec5 eeee f8e3 3b19 87a0
...
0x1720: 8cfc 15ff 5e4c e85c eeee f8e3 3b19 87a0
...
0x1d10: ecfa 2a3a 19ab c78c eeee f8e3 3b19 87a0
...
0x2070: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 7
0x2120: 7c88 4ca5 5c57 7dcc 0d34 7577 f778 7e0a
0x2130: f032 e093 7489 0740 3008 ec05 0000 0080
====1==== ====2====
hdr_off ^
pkt_len = 0x05ec ^^^^
AX_RXHDR_*=0x00830 ^^^^ ^
pkt_len = 0 ^^^^
AX_RXHDR_DROP_ERR=0x80000000 ^^^^ ^
0x2140: 3008 ec05 0000 0080 3008 5805 0000 0080
0x2150: 3008 ec05 0000 0080 3008 ec05 0000 0080
0x2160: 3008 5803 0000 0080 3008 c800 0000 0080
===11==== ===12==== ===13==== ===14====
0x2170: 0000 0000 0e00 3821
^^^^ ^^^^ rx_hdr
^^^^ pkt_cnt=14
^^^^ hdr_off=0x2138
^^^^ ^^^^ padding
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup")
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ADATA IM2P33F8ABR1 reports bogus eui64 values that appear to be the same
across all drives. Quirk them out so they are not marked as "non globally
unique" duplicates.
Co-developed-by: Felipe de Jesus Araujo da Conceição <felipe.conceicao@petrosoftdesign.com>
Signed-off-by: Felipe de Jesus Araujo da Conceição <felipe.conceicao@petrosoftdesign.com>
Signed-off-by: Lamarque V. Souza <lamarque.souza@petrosoftdesign.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the clear_ids attribute is set to true, the EUI/GUID/UUID is cleared
for the passthru target. By default, loop targets will set clear_ids to
true.
This resolves an issue where a connect to a passthru target fails when
using a trtype of 'loop' because EUI/GUID/UUID is not unique.
Fixes: 2079f41ec6 ("nvme: check that EUI/GUID/UUID are globally unique")
Signed-off-by: Alan Adamson <alan.adamson@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On failure, devm_platform_ioremap_resource() returns a ERR_PTR() value
and not NULL. Fix return value checking by using IS_ERR() and return
PTR_ERR() as error value.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628131259.3109124-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
The KASAN logs are as follows:
[ 767.617392] ==================================================================
[ 767.630776] BUG: KASAN: use-after-free in bond_3ad_state_machine_handler+0x13dc/0x1470
[ 767.638764] Read of size 2 at addr ffff00011ba9d430 by task kworker/u8:7/767
[ 767.647361] CPU: 3 PID: 767 Comm: kworker/u8:7 Tainted: G O 5.15.11 #15
[ 767.655329] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 767.660760] Workqueue: lacp_1 bond_3ad_state_machine_handler
[ 767.666468] Call trace:
[ 767.668930] dump_backtrace+0x0/0x2d0
[ 767.672625] show_stack+0x24/0x30
[ 767.675965] dump_stack_lvl+0x68/0x84
[ 767.679659] print_address_description.constprop.0+0x74/0x2b8
[ 767.685451] kasan_report+0x1f0/0x260
[ 767.689148] __asan_load2+0x94/0xd0
[ 767.692667] bond_3ad_state_machine_handler+0x13dc/0x1470
Fixes: 0622cab034 ("bonding: fix 802.3ad aggregator reselection")
Co-developed-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220629012914.361-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need to store the result of the addition back to variable count
after the addition. The store is redundant, replace += with just +
Cleans up clang scan build warning:
warning: Although the value stored to 'count' is used in the enclosing
expression, the value is never actually read from 'count'
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220628145406.183527-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes: dde2584692 ("net: usb/phy: asix: add support for ax88772A/C PHYs")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241 ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Fixes: 877bd862f3 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220628093517.7469-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The incorrect path is causing the following error when trying to run net
kselftests:
In file included from bpf/nat6to4.c:43:
../../../lib/bpf/bpf_helpers.h:11:10: fatal error: 'bpf_helper_defs.h' file not found
^~~~~~~~~~~~~~~~~~~
1 error generated.
Fixes: cf67838c44 ("selftests net: fix bpf build error")
Signed-off-by: Coleman Dietsch <dietschc@csp.edu>
Link: https://lore.kernel.org/r/20220628174744.7908-1-dietschc@csp.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Restore set counter when one of the CPU loses race to add elements
to sets.
2) After NF_STOLEN, skb might be there no more, update nftables trace
infra to avoid access to skb in this case. From Florian Westphal.
3) nftables bridge might register a prerouting hook with zero priority,
br_netfilter incorrectly skips it. Also from Florian.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: br_netfilter: do not skip all hooks with 0 priority
netfilter: nf_tables: avoid skb access on nf_stolen
netfilter: nft_dynset: restore set element counter when failing to update
====================
Link: https://lore.kernel.org/r/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a KASAN warning in raid5_add_disk when running the LVM testsuite.
The warning happens in the test
lvconvert-raid-reshape-linear_to_raid6-single-type.sh. We fix the warning
by verifying that rdev->saved_raid_disk is within limits.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
There's a KASAN warning in raid5_remove_disk when running the LVM
testsuite. We fix this warning by verifying that the "number" variable is
within limits.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
x86_64 allmodconfig build with W=1 gives these warnings:
drivers/ata/pata_cs5535.c: In function ‘cs5535_set_piomode’:
drivers/ata/pata_cs5535.c:93:11: error: variable ‘dummy’ set but not
used [-Werror=unused-but-set-variable]
u32 reg, dummy;
^~~~~
drivers/ata/pata_cs5535.c: In function ‘cs5535_set_dmamode’:
drivers/ata/pata_cs5535.c:132:11: error: variable ‘dummy’ set but not
used [-Werror=unused-but-set-variable]
u32 reg, dummy;
^~~~~
cc1: all warnings being treated as errors
Mark variables 'dummy' as "maybe unused" as they are only ever written
in rdmsr() calls.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Bpftool used to bump the memlock rlimit to make sure to be able to load
BPF objects. After the kernel has switched to memcg-based memory
accounting [0] in 5.11, bpftool has relied on libbpf to probe the system
for memcg-based accounting support and for raising the rlimit if
necessary [1]. But this was later reverted, because the probe would
sometimes fail, resulting in bpftool not being able to load all required
objects [2].
Here we add a more efficient probe, in bpftool itself. We first lower
the rlimit to 0, then we attempt to load a BPF object (and finally reset
the rlimit): if the load succeeds, then memcg-based memory accounting is
supported.
This approach was earlier proposed for the probe in libbpf itself [3],
but given that the library may be used in multithreaded applications,
the probe could have undesirable consequences if one thread attempts to
lock kernel memory while memlock rlimit is at 0. Since bpftool is
single-threaded and the rlimit is process-based, this is fine to do in
bpftool itself.
This probe was inspired by the similar one from the cilium/ebpf Go
library [4].
[0] commit 97306be45f ("Merge branch 'switch to memcg-based memory accounting'")
[1] commit a777e18f1b ("bpftool: Use libbpf 1.0 API mode instead of RLIMIT_MEMLOCK")
[2] commit 6b4384ff10 ("Revert "bpftool: Use libbpf 1.0 API mode instead of RLIMIT_MEMLOCK"")
[3] https://lore.kernel.org/bpf/20220609143614.97837-1-quentin@isovalent.com/t/#u
[4] https://github.com/cilium/ebpf/blob/v0.9.0/rlimit/rlimit.go#L39
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yafang Shao <laoar.shao@gmail.com>
Link: https://lore.kernel.org/bpf/20220629111351.47699-1-quentin@isovalent.com
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622063231.20612-1-jiangjian@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes: 5b5513b880 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stanislav Fomichev says:
====================
This series implements new lsm flavor for attaching per-cgroup programs to
existing lsm hooks. The cgroup is taken out of 'current', unless
the first argument of the hook is 'struct socket'. In this case,
the cgroup association is taken out of socket. The attachment
looks like a regular per-cgroup attachment: we add new BPF_LSM_CGROUP
attach type which, together with attach_btf_id, signals per-cgroup lsm.
Behind the scenes, we allocate trampoline shim program and
attach to lsm. This program looks up cgroup from current/socket
and runs cgroup's effective prog array. The rest of the per-cgroup BPF
stays the same: hierarchy, local storage, retval conventions
(return 1 == success).
Current limitations:
* haven't considered sleepable bpf; can be extended later on
* not sure the verifier does the right thing with null checks;
see latest selftest for details
* total of 10 (global) per-cgroup LSM attach points
v11:
- Martin: address selftest memory & fd leaks
- Martin: address moving into root (instead have another temp leaf cgroup)
- Martin: move tools/include/uapi/linux/bpf.h change from libbpf patch
into 'sync tools' patch
v10:
- Martin: reword commit message, drop outdated items
- Martin: remove rcu_real_lock from __cgroup_bpf_run_lsm_current
- Martin: remove CONFIG_BPF_LSM from cgroup_bpf_release
- Martin: fix leaking shim reference in bpf_cgroup_link_release
- Martin: WARN_ON_ONCE for bpf_trampoline_lookup in bpf_trampoline_unlink_cgroup_shim
- Martin: sync tools/include/linux/btf_ids.h
- Martin: move progs/flags closer to the places where they are used in __cgroup_bpf_query
- Martin: remove sk_clone_security & sctp_bind_connect from bpf_lsm_locked_sockopt_hooks
- Martin: try to determine vmlinux btf_id in bpftool
- Martin: update tools header in a separate commit
- Quentin: do libbpf_find_kernel_btf from the ops that need it
- lkp@intel.com: another build failure
v9:
Major change since last version is the switch to bpf_setsockopt to
change the socket state instead of letting the progs poke socket directly.
This, in turn, highlights the challenge that we need to care about whether
the socket is locked or not when we call bpf_setsockopt. (with my original
example selftest, the hooks are running early in the init phase for this
not to matter).
For now, I've added two btf id lists:
* hooks where we know the socket is locked and it's safe to call bpf_setsockopt
* hooks where we know the socket is _not_ locked, but the hook works on
the socket that's not yet exposed to userspace so it should be safe
(for this mode, special new set of bpf_{s,g}etsockopt helpers
is added; they don't have sock_owned_by_me check)
Going forward, for the rest of the hooks, this might be a good motivation
to expand lsm cgroup to support sleeping bpf and allow the callers to
lock/unlock sockets or have a new bpf_setsockopt variant that does the
locking.
- ifdef around cleanup in cgroup_bpf_release
- Andrii: a few nits in libbpf patches
- Martin: remove unused btf_id_set_index
- Martin: bring back refcnt for cgroup_atype
- Martin: make __cgroup_bpf_query a bit more readable
- Martin: expose dst_prog->aux->attach_btf as attach_btf_obj_id as well
- Martin: reorg check_return_code path for BPF_LSM_CGROUP
- Martin: return directly from check_helper_call (instead of goto err)
- Martin: add note to new warning in check_return_code, print only for void hooks
- Martin: remove confusing shim reuse
- Martin: use bpf_{s,g}etsockopt instead of poking into socket data
- Martin: use CONFIG_CGROUP_BPF in bpf_prog_alloc_no_stats/bpf_prog_free_deferred
v8:
- CI: fix compile issue
- CI: fix broken bpf_cookie
- Yonghong: remove __bpf_trampoline_unlink_prog comment
- Yonghong: move cgroup_atype around to fill the gap
- Yonghong: make bpf_lsm_find_cgroup_shim void
- Yonghong: rename regs to args
- Yonghong: remove if(current) check
- Martin: move refcnt into bpf_link
- Martin: move shim management to bpf_link ops
- Martin: use cgroup_atype for shim only
- Martin: go back to arrays for managing cgroup_atype(s)
- Martin: export bpf_obj_id(aux->attach_btf)
- Andrii: reorder SEC_DEF("lsm_cgroup+")
- Andrii: OPTS_SET instead of OPTS_HAS
- Andrii: rename attach_btf_func_id
- Andrii: move into 1.0 map
v7:
- there were a lot of comments last time, hope I didn't forget anything,
some of the bigger ones:
- Martin: use/extend BTF_SOCK_TYPE_SOCKET
- Martin: expose bpf_set_retval
- Martin: reject 'return 0' at the verifier for 'void' hooks
- Martin: prog_query returns all BPF_LSM_CGROUP, prog_info
returns attach_btf_func_id
- Andrii: split libbpf changes
- Andrii: add field access test to test_progs, not test_verifier (still
using asm though)
- things that I haven't addressed, stating them here explicitly, let
me know if some of these are still problematic:
1. Andrii: exposing only link-based api: seems like the changes
to support non-link-based ones are minimal, couple of lines,
so seems like it worth having it?
2. Alexei: applying cgroup_atype for all cgroup hooks, not only
cgroup lsm: looks a bit harder to apply everywhere that I
originally thought; with lsm cgroup, we have a shim_prog pointer where
we store cgroup_atype; for non-lsm programs, we don't have a
trace program where to store it, so we still need some kind
of global table to map from "static" hook to "dynamic" slot.
So I'm dropping this "can be easily extended" clause from the
description for now. I have converted this whole machinery
to an RCU-managed list to remove synchronize_rcu().
- also note that I had to introduce new bpf_shim_tramp_link and
moved refcnt there; we need something to manage new bpf_tramp_link
v6:
- remove active count & stats for shim program (Martin KaFai Lau)
- remove NULL/error check for btf_vmlinux (Martin)
- don't check cgroup_atype in bpf_cgroup_lsm_shim_release (Martin)
- use old_prog (instead of passed one) in __cgroup_bpf_detach (Martin)
- make sure attach_btf_id is the same in __cgroup_bpf_replace (Martin)
- enable cgroup local storage and test it (Martin)
- properly implement prog query and add bpftool & tests (Martin)
- prohibit non-shared cgroup storage mode for BPF_LSM_CGROUP (Martin)
v5:
- __cgroup_bpf_run_lsm_socket remove NULL sock/sk checks (Martin KaFai Lau)
- __cgroup_bpf_run_lsm_{socket,current} s/prog/shim_prog/ (Martin)
- make sure bpf_lsm_find_cgroup_shim works for hooks without args (Martin)
- __cgroup_bpf_attach make sure attach_btf_id is the same when replacing (Martin)
- call bpf_cgroup_lsm_shim_release only for LSM_CGROUP (Martin)
- drop BPF_LSM_CGROUP from bpf_attach_type_to_tramp (Martin)
- drop jited check from cgroup_shim_find (Martin)
- new patch to convert cgroup_bpf to hlist_node (Jakub Sitnicki)
- new shim flavor for 'struct sock' + list of exceptions (Martin)
v4:
- fix build when jit is on but syscall is off
v3:
- add BPF_LSM_CGROUP to bpftool
- use simple int instead of refcnt_t (to avoid use-after-free
false positive)
v2:
- addressed build bot failures
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement bpf_prog_query_opts as a more expendable version of
bpf_prog_query. Expose new prog_attach_flags and attach_btf_func_id as
well:
* prog_attach_flags is a per-program attach_type; relevant only for
lsm cgroup program which might have different attach_flags
per attach_btf_id
* attach_btf_func_id is a new field expose for prog_query which
specifies real btf function id for lsm cgroup attachments
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-10-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
lsm_cgroup/ is the prefix for BPF_LSM_CGROUP.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-9-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Has been slowly getting out of sync, let's update it.
resolve_btfids usage has been updated to match the header changes.
Also bring new parts of tools/include/uapi/linux/bpf.h.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-8-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
I don't see how to make it nice without introducing btf id lists
for the hooks where these helpers are allowed. Some LSM hooks
work on the locked sockets, some are triggering early and
don't grab any locks, so have two lists for now:
1. LSM hooks which trigger under socket lock - minority of the hooks,
but ideal case for us, we can expose existing BTF-based helpers
2. LSM hooks which trigger without socket lock, but they trigger
early in the socket creation path where it should be safe to
do setsockopt without any locks
3. The rest are prohibited. I'm thinking that this use-case might
be a good gateway to sleeping lsm cgroup hooks in the future.
We can either expose lock/unlock operations (and add tracking
to the verifier) or have another set of bpf_setsockopt
wrapper that grab the locks and might sleep.
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-7-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We have two options:
1. Treat all BPF_LSM_CGROUP the same, regardless of attach_btf_id
2. Treat BPF_LSM_CGROUP+attach_btf_id as a separate hook point
I was doing (2) in the original patch, but switching to (1) here:
* bpf_prog_query returns all attached BPF_LSM_CGROUP programs
regardless of attach_btf_id
* attach_btf_id is exported via bpf_prog_info
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-6-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow attaching to lsm hooks in the cgroup context.
Attaching to per-cgroup LSM works exactly like attaching
to other per-cgroup hooks. New BPF_LSM_CGROUP is added
to trigger new mode; the actual lsm hook we attach to is
signaled via existing attach_btf_id.
For the hooks that have 'struct socket' or 'struct sock' as its first
argument, we use the cgroup associated with that socket. For the rest,
we use 'current' cgroup (this is all on default hierarchy == v2 only).
Note that for some hooks that work on 'struct sock' we still
take the cgroup from 'current' because some of them work on the socket
that hasn't been properly initialized yet.
Behind the scenes, we allocate a shim program that is attached
to the trampoline and runs cgroup effective BPF programs array.
This shim has some rudimentary ref counting and can be shared
between several programs attaching to the same lsm hook from
different cgroups.
Note that this patch bloats cgroup size because we add 211
cgroup_bpf_attach_type(s) for simplicity sake. This will be
addressed in the subsequent patch.
Also note that we only add non-sleepable flavor for now. To enable
sleepable use-cases, bpf_prog_run_array_cg has to grab trace rcu,
shim programs have to be freed via trace rcu, cgroup_bpf.effective
should be also trace-rcu-managed + maybe some other changes that
I'm not aware of.
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-4-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
I'll be adding lsm cgroup specific helpers that grab
trampoline mutex.
No functional changes.
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220628174314.1216643-2-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit 26984d9d58 ("PM / devfreq: passive: Keep cpufreq_policy for
possible cpus") reworked governor_passive.c, and accidently added a
tab in the first line, i.e., the SPDX-License-Identifier line.
The checkpatch script warns with the SPDX_LICENSE_TAG warning, and hence
pointed this issue out while investigating checkpatch warnings.
Revert this editing accident. No functional change.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Remove cpufreq_passive_unregister_notifier from
cpufreq_passive_register_notifier in case of error as devfreq core
already call unregister on GOV_START fail.
This fix the kernel always printing a WARN on governor PROBE_DEFER as
cpufreq_passive_unregister_notifier is called two times and return
error on the second call as the cpufreq is already unregistered.
Fixes: a03dacb031 ("PM / devfreq: Add cpu based scaling support to passive governor")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On a devfreq PROBE_DEFER, the freq_table in the driver profile struct,
is never reset and may be leaved in an undefined state.
This comes from the fact that we store the freq_table in the driver
profile struct that is commonly defined as static and not reset on
PROBE_DEFER.
We currently skip the reinit of the freq_table if we found
it's already defined since a driver may declare his own freq_table.
This logic is flawed in the case devfreq core generate a freq_table, set
it in the profile struct and then PROBE_DEFER, freeing the freq_table.
In this case devfreq will found a NOT NULL freq_table that has been
freed, skip the freq_table generation and probe the driver based on the
wrong table.
To fix this and correctly handle PROBE_DEFER, use a local freq_table and
max_state in the devfreq struct and never modify the freq_table present
in the profile struct if it does provide it.
Fixes: 0ec09ac2ce ("PM / devfreq: Set the freq_table of devfreq device")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
This function only calls of_node_put() in normal path,
missing it in error paths.
Add missing of_node_put() to avoid refcount leak.
Fixes: f262f28c14 ("PM / devfreq: event: Add devfreq_event class")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
HZ macros has been centralized in units.h since [1]. Use it to avoid
duplicated definition.
[1] commit e2c77032fc ("units: add the HZ macros")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
With the passive governor, the cpu based scaling can PROBE_DEFER due to
the fact that CPU policy are not ready.
The cpufreq passive unregister notifier is called both from the
GOV_START errors and for the GOV_STOP and assume the notifier is
successfully registred every time. With GOV_START failing it's wrong to
loop over each possible CPU since the register path has failed for
some CPU policy not ready. Change the logic and unregister the notifer
based on the current allocated parent_cpu_data list to correctly handle
errors and the governor unregister path.
Fixes: a03dacb031 ("PM / devfreq: Add cpu based scaling support to passive governor")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Don't print warning when a governor PROBE_DEFER as it's not a real
GOV_START fail.
Fixes: a03dacb031 ("PM / devfreq: Add cpu based scaling support to passive governor")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The cpufreq passive register notifier can PROBE_DEFER and the devfreq
struct is freed and then reallocaed on probe retry.
The current logic assume that the code can't PROBE_DEFER so the devfreq
struct in the this variable in devfreq_passive_data is assumed to be
(if already set) always correct.
This cause kernel panic as the code try to access the wrong address.
To correctly handle this, update the this variable in
devfreq_passive_data to the devfreq reallocated struct.
Fixes: a03dacb031 ("PM / devfreq: Add cpu based scaling support to passive governor")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
