When I introduced ptracer_cred I failed to consider the weirdness of
fork where the task_struct copies the old value by default. This
winds up leaving ptracer_cred set even when a process forks and
the child process does not wind up being ptraced.
Because ptracer_cred is not set on non-ptraced processes whose
parents were ptraced this has broken the ability of the enlightenment
window manager to start setuid children.
Fix this by properly initializing ptracer_cred in ptrace_init_task
This must be done with a little bit of care to preserve the current value
of ptracer_cred when ptrace carries through fork. Re-reading the
ptracer_cred from the ptracing process at this point is inconsistent
with how PT_PTRACE_CAP has been maintained all of these years.
Tested-by: Takashi Iwai <tiwai@suse.de>
Fixes: 64b875f7ac ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The description of the connection between the dwmmc (SDIO) controller and
the Wifi chip, which is attached to the SDIO bus is wrong. Currently the
SDIO card can't be detected and thus the Wifi doesn't work.
Let's fix this by assigning the correct vmmc supply, which is the always on
regulator VDD_3V3 and remove the WLAN enable regulator altogether. Then to
properly deal with the power on/off sequence, add a mmc-pwrseq node to
describe the resources needed to detect the SDIO card.
Except for the WLAN enable GPIO and its corresponding assert/de-assert
delays, the mmc-pwrseq node also contains a handle to a clock provided by
the hi655x pmic. This clock is also needed to be able to turn on the WiFi
chip.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move the board specific descriptions for the dwmmc nodes in the hi6220 SoC
dtsi, into the hikey dts as it's there these belongs.
While changing this, let's take the opportunity to drop the use of the
"ti,non-removable" binding for one of the dwmmc device nodes, as it's not a
valid binding and not used. Drop also the unnecessary use of "num-slots =
<0x1>" for all of the dwmmc nodes, as there is no need to set this since
when default number of slots is one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add these regulators to better describe the HW, but also because those is
needed in following changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The regulator is a part of the hikey board, therefore let's move it from
the hi6220 SoC dtsi file into the hikey dts file . Let's also rename the
regulator according to the datasheet (5V_HUB) to better reflect the HW.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The hi655x PMIC provides the regulators but also a clock. The latter is
missing so let's add it. This clock is used by WiFi/Bluetooth chip, but
that connection is done in a separate change on top of this one.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
[Ulf: Split patch and updated changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The hi655x PMIC provides the regulators but also a clock. The latter is
missing in the definition, so extend the documentation to include this as
well.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
[Ulf: Split patch and updated changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
If the optional power-off-delay-us property is found, insert the
corresponding delay after asserting the GPIO during power off. This enables
a graceful shutdown sequence for some devices.
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
During power off, after the GPIO pin has been asserted, some devices like
the Wifi chip from TI, Wl18xx, needs a delay before the host continues with
clock gating and turning off regulators as to follow a graceful shutdown
sequence.
Therefore invent an optional power-off-delay-us DT binding for
mmc-pwrseq-simple, to allow us to support this constraint.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To set the mux mode of a pin two bits must be set. Up to now this is
implemented using the following idiom:
writel(mask, reg + CLR);
writel(value, reg + SET);
. This however results in the mux mode being 0 between the two writes.
On my machine there is an IC's reset pin connected to LCD_D20. The
bootloader configures this pin as GPIO output-high (i.e. not holding the
IC in reset). When Linux reconfigures the pin to GPIO the short time
LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse
the connected IC.
The same problem is present for the pin's drive strength setting which is
reset to low drive strength before using the right value.
So instead of relying on the hardware to modify the register setting
using two writes implement the bit toggling using read-modify-write.
Fixes: 17723111e6 ("pinctrl: add pinctrl-mxs support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I have not been able to dedicate time to the GPIO subsystem since quite
some time, and I don't see the situation improving in the near future.
Update the maintainers list to reflect this unfortunate fact.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out there are quite many Chromebooks out there that have the
same keyboard issue than Acer Chromebook. All of them are based on
Intel_Strago reference and report their DMI_PRODUCT_FAMILY as
"Intel_Strago" (Samsung Chromebook 3 and Cyan Chromebooks are exceptions
for which we add separate entries).
Instead of adding each machine to the quirk table, we use
DMI_PRODUCT_FAMILY of "Intel_Strago" that hopefully covers most of the
machines out there currently.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Suggested: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes it is more convenient to be able to match a whole family of
products, like in case of bunch of Chromebooks based on Intel_Strago to
apply a driver quirk instead of quirking each machine one-by-one.
This adds support for DMI_PRODUCT_FAMILY identification string and also
exports it to the userspace through sysfs attribute just like the
existing ones.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Crystal Cove PMIC has 16 real GPIOs but the ACPI code for devices
with this PMIC may address up to 95 GPIOs, these extra GPIOs are
called virtual GPIOs and are used by the ACPI code as a method of
accessing various non GPIO bits of PMIC.
Commit dcdc3018d6 ("gpio: crystalcove: support virtual GPIO") added
dummy support for these to avoid a bunch of ACPI errors, but instead of
ignoring writes / reads to them by doing:
if (gpio >= CRYSTALCOVE_GPIO_NUM)
return 0;
It accidentally introduced the following wrong check:
if (gpio > CRYSTALCOVE_VGPIO_NUM)
return 0;
Which means that attempts by the ACPI code to access these gpios
causes some arbitrary gpio to get touched through for example
GPIO1P0CTLO + gpionr % 8.
Since we do support input/output (but not interrupts) on the 0x5e
virtual GPIO, this commit makes to_reg return -ENOTSUPP for unsupported
virtual GPIOs so as to not have to check for (gpio >= CRYSTALCOVE_GPIO_NUM
&& gpio != 0x5e) everywhere and to make it easier to add support for more
virtual GPIOs in the future.
It then adds a check for to_reg returning an error to all callers where
this may happen fixing the ACPI code accessing virtual GPIOs accidentally
causing changes to real GPIOs.
Fixes: dcdc3018d6 ("gpio: crystalcove: support virtual GPIO")
Cc: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I failed to properly onion-wrap the unwind code: We acquire the vblank
reference before we start with the wait-wound locking dance, hence we
must make sure we retry before we drop the reference. Oops.
v2: The vblank_put must be after the frambuffer_put (Michel). I suck at
unwrapping code that doesn't use separate labels for each stage, but
checks each pointer first ... While re-reading everything I also
realized that we must clean up the fb refcounts, and specifically
plane->old_fb before we drop the locks, either in the final unlocking,
or in the w/w retry path. Hence the correct fix is to drop the
vblank_put to the very bottom.
Fixes: 29dc0d1de1 ("drm: Roll out acquire context for the page_flip ioctl")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170522135945.28831-1-daniel.vetter@ffwll.ch
This model is actually called 92XXM2-8 in Windows driver. But since pin
configs for M22 and M28 are identical, just reuse M22 quirk.
Fixes external microphone (tested) and probably docking station ports
(not tested).
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With enabling this workaround, can observe GPU hang issue on Gen9. As
currently host side doesn't have this workaround, disable it from GVT
side.
v2:
- Fix indent error.(Zhenyu)
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
crypto_gcm_setkey() was using wait_for_completion_interruptible() to
wait for completion of async crypto op but if a signal occurs it
may return before DMA ops of HW crypto provider finish, thus
corrupting the data buffer that is kfree'ed in this case.
Resolve this by using wait_for_completion() instead.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
drbg_kcapi_sym_ctr() was using wait_for_completion_interruptible() to
wait for completion of async crypto op but if a signal occurs it
may return before DMA ops of HW crypto provider finish, thus
corrupting the output buffer.
Resolve this by using wait_for_completion() instead.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
public_key_verify_signature() was passing the CRYPTO_TFM_REQ_MAY_BACKLOG
flag to akcipher_request_set_callback() but was not handling correctly
the case where a -EBUSY error could be returned from the call to
crypto_akcipher_verify() if backlog was used, possibly casuing
data corruption due to use-after-free of buffers.
Resolve this by handling -EBUSY correctly.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fix from Herbert Xu:
"This fixes a regression in the skcipher interface that allows bogus
key parameters to hit underlying implementations which can cause
crashes"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Add missing API setkey checks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=vd/K
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fix from Kees Cook:
"Marta noticed another misbehavior in EFI pstore, which this fixes.
Hopefully this is the last of the v4.12 fixes for pstore!"
* tag 'pstore-v4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
efi-pstore: Fix write/erase id tracking
- Revert a 4.11 commit related to the ACPI-based handling of laptop
lids that made changes incompatible with existing user space
stacks and broke things there (Lv Zheng).
- Add .gitignore to the ACPI tools directory (Prarit Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2ew/
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a 4.11 change that turned out to be problematic and add a
.gitignore file.
Specifics:
- Revert a 4.11 commit related to the ACPI-based handling of laptop
lids that made changes incompatible with existing user space stacks
and broke things there (Lv Zheng).
- Add .gitignore to the ACPI tools directory (Prarit Bhargava)"
* tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / button: Remove lid_init_state=method mode"
tools/power/acpi: Add .gitignore file
- Fix RTC wakeup from suspend-to-idle broken by the recent rework
of ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return
an error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2sNW
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix RTC wakeup from suspend-to-idle broken recently, fix CPU
idleness detection condition in the schedutil cpufreq governor, fix a
cpufreq driver build failure, fix an error code path in the power
capping framework, clean up the hibernate core and update the
intel_pstate documentation.
Specifics:
- Fix RTC wakeup from suspend-to-idle broken by the recent rework of
ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return an
error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar)"
* tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dbx500: add a Kconfig symbol
PM / hibernate: Declare variables as static
PowerCap: Fix an error code in powercap_register_zone()
RTC: rtc-cmos: Fix wakeup from suspend-to-idle
PM / wakeup: Fix up wakeup_source_report_event()
cpufreq: intel_pstate: Document the current behavior and user interface
cpufreq: schedutil: use now as reference when aggregating shared policy requests
We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Fixes: 9d64084330 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ci_role BUGs when the role is >= CI_ROLE_END.
This is the case while the role is changing.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ci_role BUGs when the role is >= CI_ROLE_END.
Cc: stable@vger.kernel.org #v3.10+
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When using the 'object' sysfs attribute, T100 is not displayed in
the output.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The datasheet and application note does not mention an allowed range for
the M09_REGISTER_THRESHOLD parameter. One of our customers needs to set
lower values than 20 and they seem to work just fine on EDT EP0xx0M09 with
T5x06 touch.
So, lacking a known lower limit, we increase the range for thresholds,
and set the lower limit to 0. The documentation is updated accordingly.
Signed-off-by: Schoefegger Stefan <stefan.schoefegger@ginzinger.com>
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prior to the pstore interface refactoring, the "id" generated during
a backend pstore_write() was only retained by the internal pstore
inode tracking list. Additionally the "part" was ignored, so EFI
would encode this in the id. This corrects the misunderstandings
and correctly sets "id" during pstore_write(), and uses "part"
directly during pstore_erase().
Reported-by: Marta Lofstedt <marta.lofstedt@intel.com>
Fixes: 76cc9580e3 ("pstore: Replace arguments for write() API")
Fixes: a61072aae6 ("pstore: Replace arguments for erase() API")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Commit d224e93818 ("drivers/md/dm-ioctl.c: use kvmalloc rather than
opencoded variant") left out the __GFP_HIGH flag when converting from
__vmalloc to kvmalloc. This can cause the DM ioctl to fail in some low
memory situations where it wouldn't have failed earlier. Add __GFP_HIGH
back to avoid any potential regression.
Fixes: d224e93818 ("drivers/md/dm-ioctl.c: use kvmalloc rather than opencoded variant")
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit cc7b0d4955 ("PCI: designware: Update PCI config space remap
function") made PCI configuration requests non-posted, which means we now
get a synchronous abort when the CFG space read to probe for downstream
devices times out.
Synchronous aborts need to be handled differently from the async aborts we
were getting before, in particular the PC needs to be advanced when
resolving the abort. This is mostly a copy of what other PCI drivers do on
ARM to handle those aborts.
[bhelgaas: changelog, "Fixes"]
Fixes: cc7b0d4955 ("PCI: designware: Update PCI config space remap function")
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
When a switch endpoint is configured without NTB, the mmio_ntb registers
will read all zeros. However, in corner case configurations where the
partition ID is not zero and NTB is not enabled, the code will have the
wrong partition ID and this causes the driver to use the wrong set of
drivers. To fix this we simply take the partition ID from the system info
region.
Reported-by: Dingbao Chen <dingbao.chen@microsemi.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert from "cdev_add() + device_add()" to cdev_device_add(), and from
"device_del() + cdev_del()" to cdev_device_del().
[bhelgaas: changelog]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If NO_DMA=y:
drivers/built-in.o: In function `__pci_epc_create':
(.text+0xef4e): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epc_add_epf':
(.text+0xf676): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_alloc_space':
(.text+0xfa32): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_free_space':
(.text+0xfac4): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Default value of io.low limit is 0. If user doesn't configure the limit,
last patch makes cgroup be throttled to very tiny bps/iops, which could
stall the system. A cgroup with default settings of io.low limit really
means nothing, so we force user to configure all settings, otherwise
io.low limit doesn't take effect. With this stragety, default setting of
latency/idle isn't important, so just set them to very conservative and
safe value.
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a cgroup with low limit 0 for both bps/iops, the cgroup's low limit
is ignored and we throttle the cgroup with its max limit. In this way,
other cgroups with a low limit will not get protected. To fix this, we
don't do the exception any more. cgroup will be throttled to a limit 0
if it uese default setting. To avoid completed stall, we give such
cgroup tiny IO resources.
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
These info are important to understand what's happening and help debug.
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
For idle time, children's setting should not be bigger than parent's.
For latency target, children's setting should not be smaller than
parent's. The leaf nodes will adjust their settings according to the
hierarchy and compare their IO with the settings and do
upgrade/downgrade. parents nodes don't need to track their IO
latency/idle time.
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a kthread forks (e.g. usermodehelper since commit 1da5c46fa9) but
fails in copy_process() between calling dup_task_struct() and setting
p->set_child_tid, then the value of p->set_child_tid will be inherited
from the parent and get prematurely freed by free_kthread_struct().
kthread()
- worker_thread()
- process_one_work()
| - call_usermodehelper_exec_work()
| - kernel_thread()
| - _do_fork()
| - copy_process()
| - dup_task_struct()
| - arch_dup_task_struct()
| - tsk->set_child_tid = current->set_child_tid // implied
| - ...
| - goto bad_fork_*
| - ...
| - free_task(tsk)
| - free_kthread_struct(tsk)
| - kfree(tsk->set_child_tid)
- ...
- schedule()
- __schedule()
- wq_worker_sleeping()
- kthread_data(task)->flags // UAF
The problem started showing up with commit 1da5c46fa9 since it reused
->set_child_tid for the kthread worker data.
A better long-term solution might be to get rid of the ->set_child_tid
abuse. The comment in set_kthread_struct() also looks slightly wrong.
Debugged-by: Jamie Iles <jamie.iles@oracle.com>
Fixes: 1da5c46fa9 ("kthread: Make struct kthread kmalloc'ed")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jamie Iles <jamie.iles@oracle.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170509073959.17858-1-vegard.nossum@oracle.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Markus reported that the glibc/nptl/tst-robustpi8 test was failing after
commit:
cfafcd117d ("futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()")
The following trace shows the problem:
ld-linux-x86-64-2161 [019] .... 410.760971: SyS_futex: 00007ffbeb76b028: 80000875 op=FUTEX_LOCK_PI
ld-linux-x86-64-2161 [019] ...1 410.760972: lock_pi_update_atomic: 00007ffbeb76b028: curval=80000875 uval=80000875 newval=80000875 ret=0
ld-linux-x86-64-2165 [011] .... 410.760978: SyS_futex: 00007ffbeb76b028: 80000875 op=FUTEX_UNLOCK_PI
ld-linux-x86-64-2165 [011] d..1 410.760979: do_futex: 00007ffbeb76b028: curval=80000875 uval=80000875 newval=80000871 ret=0
ld-linux-x86-64-2165 [011] .... 410.760980: SyS_futex: 00007ffbeb76b028: 80000871 ret=0000
ld-linux-x86-64-2161 [019] .... 410.760980: SyS_futex: 00007ffbeb76b028: 80000871 ret=ETIMEDOUT
Task 2165 does an UNLOCK_PI, assigning the lock to the waiter task 2161
which then returns with -ETIMEDOUT. That wrecks the lock state, because now
the owner isn't aware it acquired the lock and removes the pending robust
list entry.
If 2161 is killed, the robust list will not clear out this futex and the
subsequent acquire on this futex will then (correctly) result in -ESRCH
which is unexpected by glibc, triggers an internal assertion and dies.
Task 2161 Task 2165
rt_mutex_wait_proxy_lock()
timeout();
/* T2161 is still queued in the waiter list */
return -ETIMEDOUT;
futex_unlock_pi()
spin_lock(hb->lock);
rtmutex_unlock()
remove_rtmutex_waiter(T2161);
mark_lock_available();
/* Make the next waiter owner of the user space side */
futex_uval = 2161;
spin_unlock(hb->lock);
spin_lock(hb->lock);
rt_mutex_cleanup_proxy_lock()
if (rtmutex_owner() !== current)
...
return FAIL;
....
return -ETIMEOUT;
This means that rt_mutex_cleanup_proxy_lock() needs to call
try_to_take_rt_mutex() so it can take over the rtmutex correctly which was
assigned by the waker. If the rtmutex is owned by some other task then this
call is harmless and just confirmes that the waiter is not able to acquire
it.
While there, fix what looks like a merge error which resulted in
rt_mutex_cleanup_proxy_lock() having two calls to
fixup_rt_mutex_waiters() and rt_mutex_wait_proxy_lock() not having any.
Both should have one, since both potentially touch the waiter list.
Fixes: 38d589f2fd ("futex,rt_mutex: Restructure rt_mutex_finish_proxy_lock()")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Bug-Spotted-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Link: http://lkml.kernel.org/r/20170519154850.mlomgdsd26drq5j6@hirez.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
-----BEGIN PGP SIGNATURE-----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=luks
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.12a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 4.12 cycle.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
Pull networking fixes from David Miller:
"Mostly netfilter bug fixes in here, but we have some bits elsewhere as
well.
1) Don't do SNAT replies for non-NATed connections in IPVS, from
Julian Anastasov.
2) Don't delete conntrack helpers while they are still in use, from
Liping Zhang.
3) Fix zero padding in xtables's xt_data_to_user(), from Willem de
Bruijn.
4) Add proper RCU protection to nf_tables_dump_set() because we
cannot guarantee that we hold the NFNL_SUBSYS_NFTABLES lock. From
Liping Zhang.
5) Initialize rcv_mss in tcp_disconnect(), from Wei Wang.
6) smsc95xx devices can't handle IPV6 checksums fully, so don't
advertise support for offloading them. From Nisar Sayed.
7) Fix out-of-bounds access in __ip6_append_data(), from Eric
Dumazet.
8) Make atl2_probe() propagate the error code properly on failures,
from Alexey Khoroshilov.
9) arp_target[] in bond_check_params() is used uninitialized. This
got changes from a global static to a local variable, which is how
this mistake happened. Fix from Jarod Wilson.
10) Fix fallout from unnecessary NULL check removal in cls_matchall,
from Jiri Pirko. This is definitely brown paper bag territory..."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
net: sched: cls_matchall: fix null pointer dereference
vsock: use new wait API for vsock_stream_sendmsg()
bonding: fix randomly populated arp target array
net: Make IP alignment calulations clearer.
bonding: fix accounting of active ports in 3ad
net: atheros: atl2: don't return zero on failure path in atl2_probe()
ipv6: fix out of bound writes in __ip6_append_data()
bridge: start hello_timer when enabling KERNEL_STP in br_stp_start
smsc95xx: Support only IPv4 TCP/UDP csum offload
arp: always override existing neigh entries with gratuitous ARP
arp: postpone addr_type calculation to as late as possible
arp: decompose is_garp logic into a separate function
arp: fixed error in a comment
tcp: initialize rcv_mss to TCP_MIN_MSS instead of 0
netfilter: xtables: fix build failure from COMPAT_XT_ALIGN outside CONFIG_COMPAT
ebtables: arpreply: Add the standard target sanity check
netfilter: nf_tables: revisit chain/object refcounting from elements
netfilter: nf_tables: missing sanitization in data from userspace
netfilter: nf_tables: can't assume lock is acquired when dumping set elems
netfilter: synproxy: fix conntrackd interaction
...
The driver checks an incorrect flag of functionality of adapter.
When a driver requires i2c_smbus_read_byte_data and
i2c_smbus_write_byte_data, it should check I2C_FUNC_SMBUS_BYTE_DATA
instead I2C_FUNC_I2C.
This patch fixes the problem.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
fix extra controller reference taken on reconnect by moving
reference to initial controller create
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
correct nvme status set on abort. Patch that changed status to being actual
nvme status crossed in the night with the patch that added abort values.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Per the review by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
Looked at existing warn vs info vs err dev_xxx levels for the messages
printed on reconnects and deletes:
- Resets due to error and resets transitioned to deletes are dev_warn
- Other reset/disconnect messages are dev_info
- Removed chatty io queue related messages
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
