Add device ID specific to AM64 and J7200 in pci_endpoint_test so that
endpoints configured with those deviceIDs can use pci_endpoint_test
driver.
Link: https://lore.kernel.org/r/20210811123336.31357-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
AM64 has the same PCIe IP as in J7200 with certain erratas not
applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host"
compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.
Link: https://lore.kernel.org/r/20210811123336.31357-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
If re-registering an MR in hns_roce_rereg_user_mr(), we should return NULL
instead of passing 0 to ERR_PTR for clarity.
Fixes: 4e9fc1dae2 ("RDMA/hns: Optimize the MR registration process")
Link: https://lore.kernel.org/r/20210804125939.20516-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In Kconfig, references to config symbols do not use the prefix "CONFIG_".
Commit fa0cf568fd ("RDMA/irdma: Add irdma Kconfig/Makefile and remove
i40iw") selects config CONFIG_AUXILIARY_BUS in config INFINIBAND_IRDMA,
but intended to select config AUXILIARY_BUS.
Fixes: fa0cf568fd ("RDMA/irdma: Add irdma Kconfig/Makefile and remove i40iw")
Link: https://lore.kernel.org/r/20210817084158.10095-1-lukas.bulwahn@gmail.com
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.
/sys/kernel/tracing # ls events/task/task_rename
enable filter format hist id trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[ 113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read
To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.
Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add Documentation to help users use PCI endpoint to create virtual
functions using configfs. An endpoint function is designated as a
virtual endpoint function device when it is linked to a physical
endpoint function device (instead of a endpoint controller).
Link: https://lore.kernel.org/r/20210819123343.1951-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Populate sriov_configure ops with pci_sriov_configure_simple to
configure SR-IOV device.
Link: https://lore.kernel.org/r/20210819123343.1951-8-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that support for SR-IOV is added in PCIe endpoint core, add support
to configure virtual functions in the Cadence PCIe EP driver.
Link: https://lore.kernel.org/r/20210819123343.1951-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Simplify code to get register base address for
configuring PCI BAR.
Link: https://lore.kernel.org/r/20210819123343.1951-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
While the physical function has to be linked to endpoint controller, the
virtual function has to be linked to a physical function. Add support to
link a physical function to a virtual function in pci-ep-cfs.
Link: https://lore.kernel.org/r/20210819123343.1951-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support to add virtual function in endpoint core. The virtual
function can only be associated with a physical function instead of a
endpoint controller. Provide APIs to associate a virtual function with
a physical function here.
[weiyongjun1@huawei.com: PCI: endpoint: Fix missing unlock on error in
pci_epf_add_vepf() - Reported-by: Hulk Robot <hulkci@huawei.com>]
Link: https://lore.kernel.org/r/20210819123343.1951-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add binding to specify virtual function (associated with each physical
function) in endpoint mode.
Link: https://lore.kernel.org/r/20210819123343.1951-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
In preparation to allow event probes to use the process_fetch_insn()
callback in trace_probe_tmpl.h, change the data passed to it from a
pointer to pt_regs, as the event probe will not be using regs, and make it
a void pointer instead.
Update the process_fetch_insn() callers for kprobe and uprobe events to
have the regs defined in the function and just typecast the void pointer
parameter.
Link: https://lkml.kernel.org/r/20210819041842.291622924@goodmis.org
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Instead of a boolean "is_return" have traceprobe_set_print_fmt() take a
type (currently just PROBE_PRINT_NORMAL and PROBE_PRINT_RETURN). This will
simplify adding different types. For example, the development of the
event_probe, will need its own type as it prints an event, and not an IP.
Link: https://lkml.kernel.org/r/20210819041842.104626301@goodmis.org
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As reported by a comment in the c_can_start_xmit() this was not a FIFO.
C/D_CAN controller sends out the buffers prioritized so that the lowest
buffer number wins.
What did c_can_start_xmit() do if head was less tail in the tx ring ? It
waited until all the frames queued in the FIFO was actually transmitted
by the controller before accepting a new CAN frame to transmit, even if
the FIFO was not full, to ensure that the messages were transmitted in
the order in which they were loaded.
By storing the frames in the FIFO without requiring its transmission, we
will be able to use the full size of the FIFO even in cases such as the
one described above. The transmission interrupt will trigger their
transmission only when all the messages previously loaded but stored in
less priority positions of the buffers have been transmitted.
Link: https://lore.kernel.org/r/20210807130800.5246-5-dariobin@libero.it
Suggested-by: Gianluca Falavigna <gianluca.falavigna@inwind.it>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The algorithm is already used successfully by other CAN drivers
(e.g. mcp251xfd). Its implementation was kindly suggested to me by
Marc Kleine-Budde following a patch I had previously submitted. You can
find every detail at https://lore.kernel.org/patchwork/patch/1422929/.
The idea is that after this patch, it will be easier to patch the driver
to use the message object memory as a true FIFO.
Link: https://lore.kernel.org/r/20210807130800.5246-4-dariobin@libero.it
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The c_can_poll() handles RX/TX events unconditionally. It may therefore
happen that c_can_do_tx() is called unnecessarily because the interrupt
was triggered by the reception of a frame. In these cases, we avoid to
execute unnecessary statements and exit immediately.
Link: https://lore.kernel.org/r/20210807130800.5246-3-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The C_CAN/D_CAN cores implement 2 interfaces to manage the message
objects. To avoid concurrency and the need for locking one interface
is used in the TX path (IF_TX). While the other one, named IF_RX is
used from NAPI context only. As this interface is not only used to
manage RX, but also TX message objects, this patch renames IF_RX to
IF_NAPI.
Link: https://lore.kernel.org/r/20210809080608.171545-1-mkl@pengutronix.de
Cc: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert the Bosch C_CAN/D_CAN controller device tree binding
documentation to json-schema.
Document missing properties.
Remove "ti,hwmods" as it is no longer used in TI dts.
Make "clocks" required as it is used in all dts.
Update the examples.
Link: https://lore.kernel.org/r/20210805192750.9051-1-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Give FIFO writes the same treatment as reads to avoid fixed costs of
individual transfers on a slow bus (e.g., tcan4x5x).
Link: https://lore.kernel.org/r/20210817050853.14875-4-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On peripherals communicating over a relatively slow SPI line
(e.g. tcan4x5x), individual transfers have high fixed costs.
This causes the driver to spend most of its time waiting between
transfers and severely limits throughput.
Reduce these overheads by reading more than one word at a time.
Writing could get a similar treatment in follow-on commits.
Link: https://lore.kernel.org/r/20210817050853.14875-3-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
[mkl: remove __packed from struct id_and_dlc]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If FIFO reads or writes fail due to the underlying regmap (e.g., SPI)
I/O, propagate that up to the m_can driver, log an error, and disable
interrupts, similar to the mcp251xfd driver.
While reworking the FIFO functions to add this error handling,
add support for bulk reads and writes of multiple registers.
Link: https://lore.kernel.org/r/20210817050853.14875-2-matt@bitbashing.io
Signed-off-by: Matt Kline <matt@bitbashing.io>
[mkl: re-wrap long lines, remove WARN_ON, convert to netdev block comments]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the commenting style in the m_can driver.
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Link: https://lore.kernel.org/r/20210819111703.599686-2-mkl@pengutronix.de
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD block on RZ/G2L SoC is almost identical to one found on
R-Car Gen3 SoC's. On RZ/G2L SoC interrupt sources for each channel
are split into different sources and the IP doesn't divide (1/2)
CANFD clock within the IP.
This patch adds compatible string for RZ/G2L family and splits
the irq handlers to accommodate both RZ/G2L and R-Car Gen3 SoC's.
Link: https://lore.kernel.org/r/20210727133022.634-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
[mkl: fixed typo: recieve -> receive, thanks Geert]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the patch 07ff4aed01 ("time/timecounter: Mark 1st argument of
timecounter_cyc2time() as const") some instances of the struct
mcp251xfd_priv can be marked as const. This patch marks these as
const.
Link: https://lore.kernel.org/r/20210813091027.159379-1-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The documentation of struct es58x_fd_tx_conf_msg explains in details
the different TDC parameters. However, those description are redundant
with the documentation of struct can_tdc.
Remove most of the description.
Also, fixes a typo in the reference to the datasheet (E701 -> E70).
Link: https://lore.kernel.org/r/20210815033248.98111-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sanity checks on the control modes will reject any request related
to an unsupported features, even turning it off.
Example on an interface which does not support CAN-FD:
$ ip link set can0 type can bitrate 500000 fd off
RTNETLINK answers: Operation not supported
This patch lets such command go through (but requests to turn on an
unsupported feature are, of course, still denied).
Link: https://lore.kernel.org/r/20210815033248.98111-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.
This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.
Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable termination-* binding and provide validation example for it.
Link: https://lore.kernel.org/r/20210818071232.20585-3-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some boards provide GPIO controllable termination resistor. Provide
binding to make use of it.
Link: https://lore.kernel.org/r/20210818071232.20585-2-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The dmabuf memory registrations are missing the restrack handling and
hence do not appear in rdma tool.
Fixes: bfe0cc6eb2 ("RDMA/uverbs: Add uverbs command for dma-buf based MR registration")
Link: https://lore.kernel.org/r/20210812135607.6228-1-galpress@amazon.com
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix the below crash when deleting a slave from the unaffiliated list
twice. First time when the slave is bound to the master and the second
when the slave is unloaded.
Fix it by checking if slave is unaffiliated (doesn't have ib device)
before removing from the list.
RIP: 0010:mlx5r_mp_remove+0x4e/0xa0 [mlx5_ib]
Call Trace:
auxiliary_bus_remove+0x18/0x30
__device_release_driver+0x177/x220
device_release_driver+0x24/0x30
bus_remove_device+0xd8/0x140
device_del+0x18a/0x3e0
mlx5_rescan_drivers_locked+0xa9/0x210 [mlx5_core]
mlx5_unregister_device+0x34/0x60 [mlx5_core]
mlx5_uninit_one+0x32/0x100 [mlx5_core]
remove_one+0x6e/0xe0 [mlx5_core]
pci_device_remove+0x36/0xa0
__device_release_driver+0x177/0x220
device_driver_detach+0x3c/0xa0
unbind_store+0x113/0x130
kernfs_fop_write_iter+0x110/0x1a0
new_sync_write+0x116/0x1a0
vfs_write+0x1ba/0x260
ksys_write+0x5f/0xe0
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 93f8244431 ("RDMA/mlx5: Convert mlx5_ib to use auxiliary bus")
Link: https://lore.kernel.org/r/17ec98989b0ba88f7adfbad68eb20bce8d567b44.1628587493.git.leonro@nvidia.com
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
svc_xprt_free() already "puts" the bc_xprt before calling the
transport's "free" method. No need to do it twice.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Don't populate the array stpa on the stack but instead it
static const. Makes the object code smaller by 81 bytes:
Before:
text data bss dec hex filename
54993 17248 0 72241 11a31 ./drivers/net/ethernet/ti/cpsw_new.o
After:
text data bss dec hex filename
54784 17376 0 72160 119e0 ./drivers/net/ethernet/ti/cpsw_new.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array spec_opcode on the stack but instead it
static const. Makes the object code smaller by 158 bytes:
Before:
text data bss dec hex filename
12271 3976 128 16375 3ff7 .../hisilicon/hns3/hns3pf/hclge_cmd.o
After:
text data bss dec hex filename
12017 4072 128 16217 3f59 .../hisilicon/hns3/hns3pf/hclge_cmd.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array speeds on the stack but instead it
static const. Makes the object code smaller by 17 bytes:
Before:
text data bss dec hex filename
39987 14200 64 54251 d3eb .../huawei/hinic/hinic_sriov.o
After:
text data bss dec hex filename
39906 14264 64 54234 d3da .../huawei/hinic/hinic_sriov.o
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen says:
====================
Indirect dev ingress qdisc creation order
The first patch is just a cleanup of the code.
The second patch is fixing the dependency in ingress qdisc creation
relative to offloading driver registration to filter configurations.
v1 -> v2:
Fix warning - variable set but not used
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
