The static config of the sja1105 switch is a long stream of bytes which
is programmed to the hardware in chunks (portions with the chip select
continuously asserted) of max 256 bytes each. Each chunk is a
spi_message composed of 2 spi_transfers: the buffer with the data and a
preceding buffer with the SPI access header.
Only that certain SPI controllers, such as the spi-sc18is602 I2C-to-SPI
bridge, cannot keep the chip select asserted for that long.
The spi_max_transfer_size() and spi_max_message_size() functions are how
the controller can impose its hardware limitations upon the SPI
peripheral driver.
For the sja1105 driver to work with these controllers, both buffers must
be smaller than the transfer limit, and their sum must be smaller than
the message limit.
Regression-tested on a switch connected to a controller with no
limitations (spi-fsl-dspi) as well as with one with caps for both
max_transfer_size and max_message_size (spi-sc18is602).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has been described by Mark Brown as "not using the
[ SPI ] API at all idiomatically" due to the use of cs_change:
https://patchwork.kernel.org/project/netdevbpf/patch/20210520135031.2969183-1-olteanv@gmail.com/
According to include/linux/spi/spi.h, the chip select is supposed to be
asserted for the entire length of a SPI message, as long as cs_change is
false for all member transfers. The cs_change flag changes the following:
(i) When a non-final SPI transfer has cs_change = true, the chip select
should temporarily deassert and then reassert starting with the next
transfer.
(ii) When a final SPI transfer has cs_change = true, the chip select
should remain asserted until the following SPI message.
The sja1105 driver only uses cs_change for its first property, to form a
single SPI message whose layout can be seen below:
this is an entire, single spi_message
_______________________________________________________________________________________________
/ \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false
____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__
The fact of the matter is that spi_max_message_size() has an ambiguous
meaning if any non-final transfer has cs_change = true.
If the SPI master has a limitation in that it cannot keep the chip
select asserted for more than, say, 200 bytes (like the spi-sc18is602),
the normal thing for it to do is to implement .max_transfer_size and
.max_message_size, and limit both to 200: in the "worst case" where
cs_change is always false, then the controller can, indeed, not send
messages larger than 200 bytes.
But the fact that the SPI controller's max_message_size does not
necessarily mean that we cannot send messages larger than that.
Notably, if the SPI master special-cases the transfers with cs_change
and treats every chip select toggling as an entirely new transaction,
then a SPI message can easily exceed that limit. So there is a
temptation to ignore the controller's reported max_message_size when
using cs_change = true in non-final transfers.
But that can lead to false conclusions. As Mark points out, the SPI
controller might have a different kind of limitation with the max
message size, that has nothing at all to do with how long it can keep
the chip select asserted.
For example, that might be the case if the device is able to offload the
chip select changes to the hardware as part of the data stream, and it
packs the entire stream of commands+data (corresponding to a SPI
message) into a single DMA transfer that is itself limited in size.
So the only thing we can do is avoid ambiguity by not using cs_change at
all. Instead of sending a single spi_message, we now send multiple SPI
messages as follows:
spi_message 0 spi_message 1 spi_message n
____________________________ ___________________________ _____________________________
/ \ / \ / \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false
____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__
which is clearer because the max_message_size limit is now easier to
enforce. What is transmitted on the wire stays, of course, the same.
Additionally, because we send no more than 2 transfers at a time, we now
avoid dynamic memory allocation too, which might be seen as an
improvement by some.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the Motorcomm yt8511 phy that will be used in the
production Pine64 rk3566-quartz64 development board.
It supports gigabit transfer speeds, rgmii, and 125mhz clk output.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating to latest mainline for some testing on the GARDENA smart
gateway based on the MT7628, I noticed that ethernet does not work any
more. Commit e9229ffd55 ("net: ethernet: mtk_eth_soc: implement
dynamic interrupt moderation") introduced this problem, as it missed the
RX_DIM & TX_DIM configuration for this SoC variant. This patch fixes
this by calling mtk_dim_rx() & mtk_dim_tx() in this case as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: e9229ffd55 ("net: ethernet: mtk_eth_soc: implement dynamic interrupt moderation")
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Reto Schneider <code@reto-schneider.ch>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to keep around the dentry pointers for the debugfs
files as they will all be automatically removed when the subdir is
removed. So save the space and logic involved in keeping them around by
just getting rid of them entirely.
By doing this change, we remove one of the last in-kernel user that was
storing the result of debugfs_create_bool(), so that api can be cleaned
up.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Chao Yu <chao@kernel.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210518163304.3702015-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep around the dentry pointers for the debugfs
files as they will all be automatically removed when the subdir is
removed. So save the space and logic involved in keeping them around by
just getting rid of them entirely.
By doing this change, we remove one of the last in-kernel user that was
storing the result of debugfs_create_bool(), so that api can be cleaned
up.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210518163309.3702100-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be a mistake to fix conflicts when removing RFC tag to
repost the patch.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the compiler warns when a new value is added to the enum but
not to the string translation like:
drivers/net/ethernet/ibm/ibmvnic.c: In function 'adapter_state_to_string':
drivers/net/ethernet/ibm/ibmvnic.c:832:2: warning: enumeration value 'VNIC_FOOBAR' not handled in switch [-Wswitch]
switch (state) {
^~~~~~
drivers/net/ethernet/ibm/ibmvnic.c: In function 'reset_reason_to_string':
drivers/net/ethernet/ibm/ibmvnic.c:1935:2: warning: enumeration value 'VNIC_RESET_FOOBAR' not handled in switch [-Wswitch]
switch (reason) {
^~~~~~
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Lijun Pan <lijunp213@gmail.com>
Link: https://lore.kernel.org/netdev/CAOhMmr701LecfuNM+EozqbiTxFvDiXjFdY2aYeKJYaXq9kqVDg@mail.gmail.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
Code indent should use tabs where possible, so
use tabs instead of space for code indent.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Braces {} are not necessary for single statement blocks,
so remove these braces {}.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect code indent for conditional statements.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some blank lines after declarations as required.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/net/ethernet/microchip/encx24j600 files follows
this syntax, but the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none
drivers/net/ethernet/microchip/encx24j600_hw.h emits:
warning: expecting prototype for h(). Prototype was for _ENCX24J600_HW_H() instead
Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9 ("ixgbe: Enable jumbo frames support w/ SR-IOV")
Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-05-20
This series contains updates to igc driver only.
Andre Guedes says:
This series adds AF_XDP zero-copy feature to igc driver.
The initial patches do some code refactoring, preparing the code base to
land the AF_XDP zero-copy feature, avoiding code duplications. The last
patches of the series are the ones implementing the feature.
The last patch which indeed implements AF_XDP zero-copy support was
originally way too lengthy so, for the sake of code review, I broke it
up into two patches: one adding support for the RX functionality and the
other one adding TX support.
---
v2:
Patch 8/9 - "igc: Enable RX via AF_XDP zero-copy"
* In XDP_PASS flow, copy metadata too into the skb.
* When HW timestamp is added by the NIC, after copying it into
a local variable, update xdp_buff->data_meta so that
metadata length when XDP program is called 0.
* In igc_xdp_enable_pool(), call xsk_pool_dma_unmap() on
failure.
Known issues:
When an XDP application is running in Tx-Only mode with Zero-Copy
enabled, it is not expected to add the frames to the fill-queue. I have
noticed the following two issues in this scenario:
- If XDP_USE_NEED_WAKEUP flag is not set by application, igc_poll()
will go into infinite loop because the buffer allocation resulting
in igc_clean_rx_irq_zc() indicating that all work is not done and NAPI
should keep polling. This does not occur if XDP_USE_NEED_WAKEUP
flag is set.
- Since there are no buffers allocated by userspace for the fill
queue, there is no memory allocated for the NIC to copy the data
to. If the packet received is destined to the hardware queue where
XDP application is running, no packets are received even on other
queues.
Both these issues can be mitigated by adding a few frames to the
fill queue. The second issue can also be mitigated by making sure no
packets are being received on the hardware queue where Rx is running.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all debugfs commands have been reconstructed, and the
debugfs file node cmd is useless. So remove this debugfs file node.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for serv info is implemented by
"echo xxxx > cmd", and record the inforamtion in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"serv_info" for it, and query it by command "cat serv_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat service_task_info
local_clock: [ 114.203321]
delta: 784(ms)
last_service_task_processed: 4294918512(jiffies)
last_service_task_cnt: 4
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for dump mac tnl status is
implemented by "echo xxxx > cmd", and record the information
in dmesg. It's unnecessary and heavy. To improve it, create
a single file "mac_tnl_status" for it, and query it by command
"cat mac_tnl_status", return the result to userspace, rather
than record in dmesg.
The display style is below:
$ cat mac_tnl_status
Recently generated mac tnl interruption:
[0111204.175437] status = 0x30
[0154120.329912] status = 0x30
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets qset shaper parameters by implementing debugfs
command "echo dump qs shaper > cmd", this command will dump info in
dmesg. It's unnecessary and heavy.
As there is "tm_qset" file in tm directory for dump qset info, to
optimize these command, merge qset shaper parameters to tm_qset
file and use cat command to get them.
The display style is below:
$ cat tm_qset
ID MAP_PRI LINK_VLD MODE DWRR IR_B IR_U IR_S BS_B BS_S FLAG
0000 0 1 dwrr 100 150 7 0 5 20 0
0001 0 0 sp 0 150 7 0 5 20 0
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets qos buffer config by implementing debugfs command
"echo dump qos buf cfg > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_buf_cfg" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_buf_cfg
tx_packet_buf_tc_0: 0x120
tx_packet_buf_tc_1: 0x120
tx_packet_buf_tc_2: 0x120
tx_packet_buf_tc_3: 0x120
tx_packet_buf_tc_4: 0x0
tx_packet_buf_tc_5: 0x0
tx_packet_buf_tc_6: 0x0
tx_packet_buf_tc_7: 0x0
......
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets priority map by implementing debugfs command
"echo dump qos pri map > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_pri_map" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_pri_map
vlan_to_pri: 0
PRI TC
0 0
1 1
2 2
3 3
4 0
5 1
6 2
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets pause config by implementing debugfs command
"echo dump qos pause cfg > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_pause_cfg" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_pause_cfg
pause_trans_gap: 0x7f
pause_trans_time: 0xffff
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets tc schedule info by implementing debugfs command
"echo dump tc > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.
To optimize it, create a single file "tc_sch_info" and use cat command
to get info. It will return info to userspace, rather than record in
dmesg.
The display style is below:
$ cat tc_sch_info
enabled tc number: 4
weight_offset: 14
TC MODE WEIGHT
0 dwrr 25
1 dwrr 25
2 dwrr 25
3 dwrr 25
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets some tm info by implementing debugfs command
"echo dump tm > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.
In addition, the info of this command mixes info of qset, priority,
pg and port. Qset and priority have their own command to get info of
themself, so can remove info of qset and priority from this command.
To optimize it, create two new files "tm_pg", "tm_port" in tm directory
and use cat command to separately get info of pg and port.
The display style is below:
$ cat tm_pg
ID PRI_MAP MODE DWRR C_IR_B C_IR_U C_IR_S C_BS_B C_BS_S ...
00 0x1f dwrr 1 75 9 0 31 20 ...
$ cat tm_port
IR_B IR_U IR_S BS_B BS_S FLAG RATE(Mbps)
75 9 0 31 20 1 200000
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for tm map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"tm_map" for it, and query it by command "cat tm_map",
return the result to userspace, rather than record in dmesg.
As user can't specify queue id in cat command, driver will return info
of all queue id.
The display style is below:
$ cat tm_map
queue_id qset_id pri_id tc_id
0000 0000 00 00
INDEX | TM BP QSET MAPPING:
0000 | 00000000:00000000:00000000:00000000:00000000:00000000:00000000
0256 | 00000000:00000000:00000000:00000000:00000000:00000002:00000000
0512 | 00000000:00000000:00000000:00000004:00000000:00000000:00000000
0768 | 00000000:00000008:00000000:00000000:00000000:00000000:00000000
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for fd tcam is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"fd_tcam" for it, and query it by command "cat fd_tcam",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat fd_tcam
read result tcam key x(31):
00000000
00000000
00000000
08000000
00000600
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
read result tcam key y(31):
00000000
00000000
00000000
f7ff0000
0000f900
00000000
00000000
00000000
00000000
00000000
00000000
00000000
0000fff8
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for queue info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create two files
"rx_queue_info" and "tx_queue_info" for it, and query it
by command "cat rx_queue_info" and "cat tx_queue_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat rx_queue_info
QUEUE_ID BD_NUM BD_LEN TAIL HEAD FBDNUM PKTNUM ...
0 0 0 0 0 0 0 ...
1 0 0 0 0 0 0 ...
2 0 0 0 0 0 0 ...
$ cat tx_queue_info
QUEUE_ID BD_NUM TC TAIL HEAD FBDNUM OFFSET PKTNUM ...
0 0 0 0 0 0 0 0 ...
1 0 0 0 0 0 0 0 ...
2 0 0 0 0 0 0 0 ...
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for queue map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"queue_map" for it, and query it by command "cat queue_map",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat queue_map
local_queue_id global_queue_id vector_id
0 0 341
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for reg is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create some files
"bios_common/ssu/igu_egu/rpu/ncsi/rtc/ppp/rcb/tqp/mac" for it,
and query it by command "cat xxx", return the result to
userspace, rather than record in dmesg.
The display style is below:
$ cat bios_common
BP_CPU_STATE: 0x0
DFX_MSIX_INFO_NIC_0: 0xc000
DFX_MSIX_INFO_NIC_1: 0x0
DFX_MSIX_INFO_NIC_2: 0x0
DFX_MSIX_INFO_NIC_3: 0x0
DFX_MSIX_INFO_ROC_0: 0xc000
DFX_MSIX_INFO_ROC_1: 0x0
DFX_MSIX_INFO_ROC_2: 0x0
DFX_MSIX_INFO_ROC_3: 0x0
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmitting packets via AF_XDP zero-copy mechanism.
The packet transmission itself is implemented by igc_xdp_xmit_zc() which
is called from igc_clean_tx_irq() when the ring has AF_XDP zero-copy
enabled. Likewise i40e and ice drivers, the transmission budget used is
the number of descriptors available on the ring.
A new tx buffer type is introduced to 'enum igc_tx_buffer_type' to
indicate the tx buffer uses memory from xsk pool so it can be properly
cleaned after transmission or when the ring is cleaned.
The I225 controller has only 4 Tx hardware queues so the main difference
between igc and other Intel drivers that support AF_XDP zero-copy is
that there is no tx ring dedicated exclusively to XDP. Instead, tx
rings are shared between the network stack and XDP, and netdev queue
lock is used to ensure mutual exclusion. This is the same approach
implemented to support XDP_TX and XDP_REDIRECT actions.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for receiving packets via AF_XDP zero-copy mechanism.
Add a new flag to 'enum igc_ring_flags_t' to indicate the ring has
AF_XDP zero-copy enabled so proper ring setup is carried out during ring
configuration in igc_configure_rx_ring().
RX buffers can now be allocated via the shared pages mechanism (default
behavior of the driver) or via xsk pool (when AF_XDP zero-copy is
enabled) so a union is added to the 'struct igc_rx_buffer' to cover both
cases.
When AF_XDP zero-copy is enabled, rx buffers are allocated from the xsk
pool using the new helper igc_alloc_rx_buffers_zc() which is the
counterpart of igc_alloc_rx_buffers().
Likewise other Intel drivers that support AF_XDP zero-copy, in igc we
have a dedicated path for cleaning up rx irqs when zero-copy is enabled.
This avoids adding too many checks within igc_clean_rx_irq(), resulting
in a more readable and efficient code since this function is called from
the hot-path of the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Up to this point, Tx buffers are associated with either a skb or a xdpf,
and the IGC_TX_FLAGS_XDP flag was enough to distinguish between these
two case. However, with upcoming patches that will add AF_XDP zero-copy
support, a third case will be introduced so this flag-based approach
won't fit well.
In preparation to land AF_XDP zero-copy support, replace the
IGC_TX_FLAGS_XDP flag by an enum which will be extended once zero-copy
support is introduced to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
unmaps Tx buffers into its own local helper so we can reuse it, avoiding
code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
updates the driver RX stats in its own local helper so it can be reused
in the zero-copy path. Likewise, encapsulate TX stats code as well.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
