This change implements the set_channel() ethtool operation,
preserving the current defaults values and allowing up set
the number of queues in the range set ad device creation
time.
The update operation tries hard to leave the device in a
consistent status in case of errors.
RFC v1 -> RFC v2:
- don't flip device status on set_channel()
- roll-back the changes if possible on error - Jackub
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract in simpler helpers the code to enable and disable a
range of xdp/napi instance, with the common property that
"disable" helpers can't fail.
Will be used by the next patch. No functional change intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth get_channel currently reports for channels being both RX/TX and
combined. As Jakub noted:
"""
ethtool man page is relatively clear, unfortunately the kernel code
is not and few read the man page. A channel is approximately an IRQ,
not a queue, and IRQ can't be dedicated and combined simultaneously
"""
This patch changes the information exposed by veth_get_channels,
setting max_combined to zero, being more consistent with the above
statement. The ethtool_channels is always cleared by the caller, we just
need to avoid setting the 'combined' fields.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cf8331825a.
There are better Linux interfaces to export the different LED modes
and blinking reasons.
Revert this patch for now and come up with better solution later.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210719101640.16047-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For hardware limitation, port VLAN filter is port level, and
effective for all the functions of the port. So if not support
port VLAN bypass, it's necessary to disable the port VLAN filter,
in order to support function level VLAN filter control.
Fixes: 2ba306627f ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When VF need response from PF, VF will wait (1us - 1s) to receive
the response, or it will wait timeout and the VF action fails.
If VF do not receive response in 1st action because timeout,
the 2nd action may receive response for the 1st action, and get
incorrect response data.VF must reciveve the right response from
PF,or it will cause unexpected error.
This patch adds match_id to check mailbox response from PF to VF,
to make sure VF get the right response:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
This scheme depends on PF driver supports match_id, if PF driver doesn't
support then VF will uses the original scheme.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the qcom_scm driver to be loadable as a permenent module.
This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).
Reviving this now that Saravana's fw_devlink defaults to on,
which should avoid loading troubles seen before.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20210707045320.529186-1-john.stultz@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF till now only manages the allocation and freeing of
MCAM rules for other PF/VFs in system. To implement
L2 switching between all CGX mapped PF and VFs, AF
requires MCAM entries for DMAC rules for each PF and VF.
This patch modifies AF driver such that AF can also
allocate MCAM rules and install rules for other
PFs and VFs. All the checks like channel verification
for RX rules and PF_FUNC verification for TX rules are
relaxed in case AF is allocating or installing rules.
Also all the entry and counter to owner mappings are
set to NPC_MCAM_INVALID_MAP when they are free indicating
those are not allocated to AF nor PF/VFs.
This patch also ensures that AF allocated and installed
entries are displayed in debugfs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_config_vf_promiscuous_mode() calls
i40e_getnum_vf_vsi_vlan_filters() without acquiring the
mac_filter_hash_lock spinlock.
This is unsafe because mac_filter_hash may get altered in another thread
while i40e_getnum_vf_vsi_vlan_filters() traverses the hashes.
Simply adding the spinlock in i40e_getnum_vf_vsi_vlan_filters() is not
possible as it already gets called in i40e_get_vlan_list_sync() with the
spinlock held. Therefore adding a wrapper that acquires the spinlock and
call the correct function where appropriate.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Fix-suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change. The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized. So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.
Fixes: 93cb62d98e ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path. Define a function to abort FW reset and
consolidate all error paths to call this new function.
Fixes: dab62e7c2d ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum
bandwidth constraints. Thus, zero is a legal value for a given TC.
However, if all the other TCs sum up to 100%, then at least one
hardware queue will starve, resulting in guaranteed TX timeouts.
Reject such nonsensical configurations.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument of phy_clear_bits_mmd(..., u16 val); is u16 and not
int, just inline the value into the function call arguments.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all vmxnet3 version 6 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 6, provided
the emulation advertises support for version 6.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the maximum configurable mtu to 9190
to accommodate jumbo packets of overlay traffic.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As vmxnet3 supports IP/TCP/UDP RSS, this patch sets appropriate
hash type based on the type of RSS performed.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vmxnet3 version 4 added support for ESP RSS. However, only IPv4 was
supported. With vmxnet3 version 6, this patch enables RSS for ESP
IPv6 packets as well.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With version 6, vmxnet3 relaxes the restriction on queues to
be power of two. This is helpful in cases (Edge VM) where
vcpus are less than 8 and device requires more than 4 queues.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, vmxnet3 supports maximum of 8 Tx/Rx queues. With increase
in number of vcpus on a VM, to achieve better performance and utilize
idle vcpus, we need to increase the max number of queues supported.
This patch enhances vmxnet3 to support maximum of 32 Tx/Rx queues.
Increasing the Rx queues also increases the probability of distrubuting
the traffic from different flows to different queues with RSS.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 is currently at version 4 and this patch initiates the
preparation to accommodate changes for upto version 6. Introduced
utility macros for vmxnet3 version 6 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nguy/next-queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-07-16
Vinicius Costa Gomes says:
Add support for steering traffic to specific RX queues using Flex Filters.
As the name implies, Flex Filters are more flexible than using
Layer-2, VLAN or MAC address filters, one of the reasons is that they
allow "AND" operations more easily, e.g. when the user wants to steer
some traffic based on the source MAC address and the packet ethertype.
Future work include adding support for offloading tc-u32 filters to
the hardware.
The series is divided as follows:
Patch 1/5, add the low level primitives for configuring Flex filters.
Patch 2/5 and 3/5, allow ethtool to manage Flex filters.
Patch 4/5, when specifying filters that have multiple predicates, use
Flex filters.
Patch 5/5, Adds support for exposing the i225 LEDs using the LED subsystem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 9a5605505d (" bonding: Add struct bond_ipesc to manage SA") is causing
following build error when XFRM is not selected in kernel config.
lld: error: undefined symbol: xfrm_dev_state_flush
>>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453)
>>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a
Fixes: 9a5605505d (" bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Taehee Yoo <ap420073@gmail.com>
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each i225 has three LEDs. Export them via the LED class framework.
Each LED is controllable via sysfs. Example:
$ cd /sys/class/leds/igc_led0
$ cat brightness # Current Mode
$ cat max_brightness # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1
The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently flex filters are only used for filters containing user data.
However, it makes sense to utilize them also for filters having
multiple conditions, because that's not supported by the driver at the
moment. Add it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allows Flex Filters to be installed.
The previous restriction to the types of filters that can be installed
can now be lifted.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex filter mechanism to extend the current ethtool filter
operations by intercoperating the user data. This allows to match
eight more bytes within a Ethernet frame in addition to macs, ether
types and vlan.
The matching pattern looks like this:
* dest_mac [6]
* src_mac [6]
* tpid [2]
* vlan tci [2]
* ether type [2]
* user data [8]
This can be used to match Profinet traffic classes by FrameID range.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.
Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
According to reference guides mt7530 (mt7620) and mt7531:
NOTE: When IVL is reset, MAC[47:0] and FID[2:0] will be used to
read/write the address table. When IVL is set, MAC[47:0] and CVID[11:0]
will be used to read/write the address table.
Since the function only fills in CVID and no FID, we need to set the
IVL bit. The existing code does not set it.
This is a fix for the issue I dropped here earlier:
http://lists.infradead.org/pipermail/linux-mediatek/2021-June/025697.html
With this patch, it is now possible to delete the 'self' fdb entry
manually. However, wifi roaming still has the same issue, the entry
does not get deleted automatically. Wifi roaming also needs a fix
somewhere else to function correctly in combination with vlan.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement Wake-on-LAN feature for 88X3310 and 88E2110.
This is done by enabling WoL interrupt and WoL detection and
configuring MAC address into WoL magic packet registers
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netdevsim only supports a single queue per port, which is
insufficient for testing multi-queue TC schedulers e.g. sch_mq. Extend
the current sysfs interface so that users can create ports with multiple
queues:
$ echo "[ID] [PORT_COUNT] [NUM_QUEUES]" > /sys/bus/netdevsim/new_device
As an example, echoing "2 4 8" creates 4 ports, with 8 queues per port.
Note, this is compatible with the current interface, with default number
of queues set to 1. For example, echoing "2 4" creates 4 ports with 1
queue per port; echoing "2" simply creates 1 port with 1 queue.
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the clang build warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1862:13: error: variable 'cur_data_offset' set but not used [-Werror,-Wunused-but-set-variable]
dma_addr_t cur_data_offset;
Signed-off-by: Bill Wendling <morbo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'bitmap_alloc()/bitmap_free()' instead of hand-writing it.
This makes the code less verbose.
Also, use 'bitmap_alloc()' instead of 'bitmap_zalloc()' because the bitmap
is fully overridden by a 'bitmap_copy()' call just after its allocation.
While at it, remove an extra and unneeded space.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'tail' pointer is also free-running count, so it needs to be masked
as 'adminq_prod_cnt' does, to become an index value of AdminQ buffer.
Fixes: 5cdad90de6 ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi Linus,
Please, pull the following patches that fix many fall-through
warnings when building with Clang and -Wimplicit-fallthrough.
This pull-request also contains the patch for Makefile that enables
-Wimplicit-fallthrough for Clang, globally.
It's also important to notice that since we have adopted the use of
the pseudo-keyword macro fallthrough; we also want to avoid having
more /* fall through */ comments being introduced. Notice that contrary
to GCC, Clang doesn't recognize any comments as implicit fall-through
markings when the -Wimplicit-fallthrough option is enabled. So, in
order to avoid having more comments being introduced, we have to use
the option -Wimplicit-fallthrough=5 for GCC, which similar to Clang,
will cause a warning in case a code comment is intended to be used
as a fall-through marking. The patch for Makefile also enforces this.
We had almost 4,000 of these issues for Clang in the beginning,
and there might be a couple more out there when building some
architectures with certain configurations. However, with the
recent fixes I think we are in good shape and it is now possible
to enable -Wimplicit-fallthrough for Clang. :)
Thanks!
-----BEGIN PGP SIGNATURE-----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=XVNN
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-clang-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"This fixes many fall-through warnings when building with Clang and
-Wimplicit-fallthrough, and also enables -Wimplicit-fallthrough for
Clang, globally.
It's also important to notice that since we have adopted the use of
the pseudo-keyword macro fallthrough, we also want to avoid having
more /* fall through */ comments being introduced. Contrary to GCC,
Clang doesn't recognize any comments as implicit fall-through markings
when the -Wimplicit-fallthrough option is enabled.
So, in order to avoid having more comments being introduced, we use
the option -Wimplicit-fallthrough=5 for GCC, which similar to Clang,
will cause a warning in case a code comment is intended to be used as
a fall-through marking. The patch for Makefile also enforces this.
We had almost 4,000 of these issues for Clang in the beginning, and
there might be a couple more out there when building some
architectures with certain configurations. However, with the recent
fixes I think we are in good shape and it is now possible to enable
the warning for Clang"
* tag 'Wimplicit-fallthrough-clang-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (27 commits)
Makefile: Enable -Wimplicit-fallthrough for Clang
powerpc/smp: Fix fall-through warning for Clang
dmaengine: mpc512x: Fix fall-through warning for Clang
usb: gadget: fsl_qe_udc: Fix fall-through warning for Clang
powerpc/powernv: Fix fall-through warning for Clang
MIPS: Fix unreachable code issue
MIPS: Fix fall-through warnings for Clang
ASoC: Mediatek: MT8183: Fix fall-through warning for Clang
power: supply: Fix fall-through warnings for Clang
dmaengine: ti: k3-udma: Fix fall-through warning for Clang
s390: Fix fall-through warnings for Clang
dmaengine: ipu: Fix fall-through warning for Clang
iommu/arm-smmu-v3: Fix fall-through warning for Clang
mmc: jz4740: Fix fall-through warning for Clang
PCI: Fix fall-through warning for Clang
scsi: libsas: Fix fall-through warning for Clang
video: fbdev: Fix fall-through warning for Clang
math-emu: Fix fall-through warning
cpufreq: Fix fall-through warning for Clang
drm/msm: Fix fall-through warning in msm_gem_new_impl()
...
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ
QL41000 ethernet controller:
BUG: scheduling while atomic: kworker/0:4/531/0x00000200
[qed_probe:488()]hw prepare failed
kernel BUG at mm/vmalloc.c:2355!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu
pstate: 00400009 (nzcv daif +PAN -UAO)
Call trace:
vunmap+0x4c/0x50
iounmap+0x48/0x58
qed_free_pci+0x60/0x80 [qed]
qed_probe+0x35c/0x688 [qed]
__qede_probe+0x88/0x5c8 [qede]
qede_probe+0x60/0xe0 [qede]
local_pci_probe+0x48/0xa0
work_for_cpu_fn+0x24/0x38
process_one_work+0x1d0/0x468
worker_thread+0x238/0x4e0
kthread+0xf0/0x118
ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in
theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in
_qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang <Lijian.Zhang@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
