Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In three places, the driver calls of_get_property and reads the property
length although the length is not used. Update the calls to not request
the length.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race condition between
both of them.
To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The label is only used once, so we delete it and use the
return statement instead of the goto statement.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210625121108.162868-1-dingsenjie@163.com
After some crashes in the 3D engine (!) on the Samsung GT-I8530
it turns out that the main firmware file can be device dependent,
something that was previously only handled for the NVRAM
parameter file.
Rewrite the code a bit so we can a per-board suffixed firmware
binary as well, if this does not exist we fall back to the
canonical firmware name.
Example: a 4330 device with the OF board compatible is
"samsung,gavini". We will first try
"brcmfmac4330-sdio.samsung,gavini.bin" then "brcmfmac4330-sdio.bin"
if that does not work.
Cc: phone-devel@vger.kernel.org
Cc: newbyte@disroot.org
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210711231659.255479-1-linus.walleij@linaro.org
There is no need in extra call indirection and check from impossible
flow where someone tries to set namespace without prior call
to devlink_alloc().
Instead of this extra logic and additional EXPORT_SYMBOL, use specialized
devlink allocation function that receives net namespace as an argument.
Such specialized API allows clear view when devlink initialized in wrong
net namespace and/or kernel users don't try to change devlink namespace
under the hood.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To have more accurate error return type use -EOPNOTSUPP instead of
-EINVAL.
Link: https://lore.kernel.org/r/20210729151732.30995-1-pkushwaha@marvell.com
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c0255717 ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Fixes: 91c0255717 ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/r/20210729141246.GA1267@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the function bcm_enetsw_probe(), 'ret' will be assigned by
bcm_enet_change_mtu(), so 'ret = 0' make no sense.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipvlan device is created on a bond device, the link state
of the ipvlan device may be abnormal. This is because bonding device
allows to add physical network card device in the down state and so
NETDEV_CHANGE event will not be notified to other listeners, so ipvlan
has no chance to update its link status.
The following steps can cause such problems:
1) bond0 is down
2) ip link add link bond0 name ipvlan type ipvlan mode l2
3) echo +enp2s7 >/sys/class/net/bond0/bonding/slaves
4) ip link set bond0 up
After these steps, use ip link command, we found ipvlan has NO-CARRIER:
ipvlan@bond0: <NO-CARRIER, BROADCAST,MULTICAST,UP,M-DOWN> mtu ...>
We can deal with this problem like VLAN: Add handling of NETDEV_UP
events. If we receive NETDEV_UP event, we will update the link status
of the ipvlan.
Signed-off-by: Di Zhu <zhudi21@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mirroring rules are added in shared filter blocks, the same
mirroring rule has to be configured on all the switch ports that are
part of the same block.
In case a switch port joins a shared block after mirroring filters have
been already added to it, then all the mirror rules should be offloaded
to the port. The reverse, removal of mirroring rules, has to be done at
block unbind.
For this purpose, the dpaa2_switch_block_offload_mirror() and
dpaa2_switch_block_unoffload_mirror() functions are added and called
upon binding and unbinding a switch port to/from a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the infrastructure added in the previous patch, extend tc-flower
support with FLOW_ACTION_MIRRED based on VLAN.
Tested with:
tc qdisc add dev eth8 ingress_block 1 clsact
tc filter add block 1 ingress protocol 802.1q flower skip_sw \
vlan_id 100 action mirred egress mirror dev eth6
tc filter del block 1 ingress pref 49152
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per port mirroring for the DPAA2 switch. We support
only single mirror port, therefore we allow mirroring rules only as long
as the destination port is always the same.
Unlike all the actions (drop, redirect, trap) already supported by the
dpaa2-switch driver, adding mirroring filters in shared blocks is not
achieved by a singular ACL entry added in a table shared by the ports.
This is why, when a new mirror filter is added in a block we have to got
through all the switch ports sharing it and configure the filter
individually on all.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary MC API for setting up and configuring the mirroring
feature on the DPSW DPAA2 object.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_matchall_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the necessary steps to offload a filter by using the ACL table
in a separate function - dpaa2_switch_cls_flower_replace_acl().
This is intended to help with the code readability when the mirroring
support is added.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, shared filter blocks were implemented only by ACL tables
shared between ports. Going forward, when the mirroring support will be
added, this will not be true anymore.
Rename the dpaa2_switch_acl_tbl into dpaa2_switch_filter_block so that
we make it clear that the structure is used not only for filters that
use the ACL table but will be used for all the filters that are added in
a block.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the dpaa2_switch_tc_parse_action() function was used for all
the supported tc actions since all of them were implemented by adding
ACL table entries. In the next commits, the dpaa2-switch driver will
gain mirroring support which is not using the same HW feature.
Make sure that we specify the ACL in the function name so that we make
it clear that it's only used for specific actions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the qede module version which is not needed and not allowed
with inbox drivers.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the qed module version which is not needed and not allowed
with inbox drivers.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Surprisingly, this configuration:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1
still has the sja1105 switch sending untagged packets to the CPU (and
failing to decode them, since dsa_find_designated_bridge_port_by_vid
searches by VID 1 and rightfully finds no bridge VLAN 1 on a port).
Dumping the switch configuration, the VLANs are managed properly:
- the pvid of swp2 is 1 in the MAC Configuration Table, but
- only the CPU port is in the port membership of VLANID 1 in the VLAN
Lookup Table
When the ingress packets are tagged with VID 1, they are properly
dropped. But when they are untagged, they are able to reach the CPU
port. Also, when the pvid in the MAC Configuration Table is changed to
e.g. 55 (an unused VLAN), the untagged packets are also dropped.
So it looks like:
- the switch bypasses ingress VLAN membership checks for untagged traffic
- the reason why the untagged traffic is dropped when I make the pvid 55
is due to the lack of valid destination ports in VLAN 55, rather than
an ingress membership violation
- the ingress VLAN membership cheks are only done for VLAN-tagged traffic
Interesting. It looks like there is an explicit bit to drop untagged
traffic, so we should probably be using that to preserve user expectations.
Note that only VLAN-aware ports should drop untagged packets due to no
pvid - when VLAN-unaware, the software bridge doesn't do this even if
there is no pvid on any bridge port and on the bridge itself. So the new
sja1105_drop_untagged() function cannot simply be called with "false"
from sja1105_bridge_vlan_add() and with "true" from sja1105_bridge_vlan_del.
Instead, we need to also consider the VLAN awareness state. That means
we need to hook the "drop untagged" setting in all the same places where
the "commit pvid" logic is, and it needs to factor in all the state when
flipping the "drop untagged" bit: is our current pvid in the VLAN Lookup
Table, and is the current port in that VLAN's port membership list?
VLAN-unaware ports will never drop untagged frames because these checks
always succeed by construction, and the tag_8021q VLANs cannot be changed
by the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we no longer have the ultra-central sja1105_build_vlan_table(),
we need to be more careful about checking all corner cases manually.
For example, when a port leaves a VLAN-aware bridge, it becomes
standalone so its pvid should become a tag_8021q RX VLAN again. However,
sja1105_commit_pvid() only gets called from sja1105_bridge_vlan_add()
and from sja1105_vlan_filtering(), and no VLAN awareness change takes
place (VLAN filtering is a global setting for sja1105, so the switch
remains VLAN-aware overall).
This means that we need to put another sja1105_commit_pvid() call in
sja1105_bridge_member().
Fixes: 6dfd23d35e ("net: dsa: sja1105: delete vlan delta save/restore logic")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an empty drivers/net/mctp/, for future interface drivers.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leveraging the previous patch we can now avoid orphaning the
skb in the veth gro path, allowing correct backpressure.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are issues when adding a bridge FDB entry as VLAN-aware
and deleting it as VLAN-unaware, or vice versa.
However this is an unneeded complication, since the bridge always
installs its default FDB entries in VLAN 0 to match on VLAN-unaware
ports, and in the default_pvid (VLAN 1) to match on VLAN-aware ports.
So instead of trying to outsmart the bridge, just install all entries it
gives us, and they will start matching packets when the vlan_filtering
mode changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW can report to driver via ASYNC event if it encountered an
invalid signal on any TSIO PIN. Driver will log this event
for the user to take corrective action.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Arvind Susarla <arvind.susarla@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the PPS pins are configured, the FW can report
PPS values using ASYNC event. This patch adds the
ASYNC event handler and subsequent reporting of the
events to kernel.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application will send ioctls to set/clear PPS pin functions
based on user input. This patch implements the driver
callbacks that will configure the TSIO pins using firmware
commands. After firmware reset, the TSIO pins will be reconfigured
again.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1PPS (One Pulse Per Second) is a signal generated either
by the NIC PHC or an external timing source.
Integrating the support to configure and use 1PPS using
the TSIO pins along with PTP timestamps will add Grand
Master capability to the 5750X family chipsets.
This patch initializes the driver data structures and
registers the 1PPS with kernel, based on the TSIO pins'
capability in the hardware. This will create a /dev/ppsX
device which applications can use to receive PPS events.
Later patches will define functions to configure and use
the pins.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error recovery or hot firmware upgrade, the chip may be under
reset and the PHC register read cycles may cause completion timeouts.
Check that the chip is not under reset condition before proceeding
to read the PHC by checking the flag BNXT_STATE_IN_FW_RESET. We also
need to take the ptp_lock before we set this flag to prevent race
conditions.
We need this logic because the PHC now will stay registered after
bnxt_close().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by Richard Cochran that registering the PHC during
probe is better than during ifup, so move bnxt_ptp_init() back to
bnxt_init_one(). In order to work correctly after firmware reset which
may result in PTP config. changes, we modify bnxt_ptp_init() to return
if the PHC has been registered earlier. If PTP is no longer supported
by the new firmware, we will unregister the PHC and clean up.
This partially reverts:
d7859afb68 ("bnxt_en: Move bnxt_ptp_init() to bnxt_open()")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some products (So) may have two different types of products
with different mac-type that are otherwise equivalent, and
have the same PNVM data, so the PNVM file will contain two
(or perhaps later more) HW-type TLVs. Accept the file and
use the data section that contains any matching entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210719140154.a6a86e903035.Ic0b1b75c45d386698859f251518e8a5144431938@changeid
The nubus core ignores the return value of the remove callback (in
nubus_device_remove()) and all implementers return 0 anyway.
So make it impossible for future drivers to return an unused error code
by changing the remove prototype to return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/20210727080840.3550927-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX8QM ENET IP version support timing specification that MAC
integrate clock delay in RGMII mode, the delayed TXC/RXC as an
alternative option to work well with various PHYs.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8MQ ENET version support IEEE802.3az eee mode, add
eee mode tx lpi enable to support ethtool interface.
usage:
1. set sleep and wake timer to 5ms:
ethtool --set-eee eth0 eee on tx-lpi on tx-timer 5000
2. check the eee mode:
~# ethtool --show-eee eth0
EEE Settings for eth0:
EEE status: enabled - active
Tx LPI: 5000 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
Note: For realtime case and IEEE1588 ptp case, it should disable
EEE mode.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENET of imx8mq and imx8qm are basically the same as imx6sx,
but they have new features support based on imx6sx, like:
- imx8mq: supports IEEE 802.3az EEE standard.
- imx8qm: supports RGMII mode delayed clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nfp_tunnel_add_ipv6_off() fails, it should return error code
in nfp_fl_ct_add_offload().
Fixes: 5a2b930416 ("nfp: flower-ct: compile match sections of flow_payload")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink is an integral part of mlx5 driver and all flows ensure that
devlink_*_register() will success. That makes the ->registered check
an obsolete.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit that introduced devlink support released devlink resources in
wrong order, that made an unwind flow to be asymmetrical. In addition,
the am65-cpsw-nuss used internal to devlink core field - registered.
In order to fix the unwind flow and remove such access to the
registered field, rewrite the code to call devlink_port_unregister only
on registered ports.
Fixes: 58356eb31d ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
