Quite often, the HW get stuck in error condition if a stream error
was detected. As documented, the HW should stop immediately and self
reset. There is likely a problem or a miss-understanding of the self
reset mechanism, as unless we make a long pause, the next command
will then report an error even if there is no error in it.
Disabling error detection fixes the issue, and let the decoder continue
after an error. This patch is safe for backport into older kernels.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently, the driver tries to validat the HEVC SPS
against the CAPTURE queue format (i.e. the decoded format).
This is not correct, because typically the SPS control is set
before the CAPTURE queue is negotiated.
Fixes: 135ad96cb4 ("media: hantro: Be more accurate on pixel formats step_width constraints")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Not all DPB entries will be used most of the time. Unused entries will
thus have invalid timestamps. They will produce negative buffer index
which is not specifically handled. This works just by chance in current
code. It will even produce bogus pointer, but since it's not used, it
won't do any harm.
Let's fix that brittle design by skipping writing DPB entry altogether
if timestamp is invalid.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity_remote_pad() is misnamed, as it operates on a pad and
not an entity. Rename it to media_pad_remote_pad_first() to clarify its
behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the newly introduced vb2_find_buffer API to get a vb2_buffer
given a buffer timestamp.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the newly introduced vb2_find_buffer API to get a vb2_buffer
given a buffer timestamp.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tiles are last remaining unimplemented functionality for HEVC. Implement
it.
[hverkuil: fix checkpatch warning, split long line in two]
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that controls can be dynamic arrays, we need to know how many
elements are in such array. Add a helper for that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that we have infrastructure for reporting errors, let's add two
checks, which will make sure slice can be actually decoded.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During decoding setup stage for complex codecs like HEVC driver can
detect inconsistent values in controls or some other task, like
allocating memory, can fail.
Currently setup stage has no way of signalling error. Change return type
of setup callback to int and if returned value is not zero, skip
decoding and finish job immediately with error flag.
While currently there is only one place when setup can fail, it's
expected that there will be more such cases in the future, when HEVC
decoding is improved.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently error messages when control creation fails are very sparse.
Granted, user should never observe them. However, developer working on
codecs can. In such cases additional information like which control
creation failed and error number are very useful.
Expand error messages with additional info.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that we know real purpose of "not low delay" flag, logic for
applying this flag should be fixed too. According to vendor and
reference implementation, low delay is signaled when POC of current
frame is lower than POC of at least one reference of a slice.
Implement mentioned logic and invert it to conform to flag meaning. Also
don't apply flag for I frames. They don't have any reference.
This fixes decoding of 3 reference bitstreams.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Bit 21 in register 0x24 (slice header info 1) actually represents
negated version of low delay flag. This can be seen in vendor Cedar
library source code. While this flag is not part of the standard, it can
be found in reference HEVC implementation.
Fix macro name and change it to flag.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that infrastructure for 10-bit decoding exists, enable it for
Allwinner H6.
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that we have proper infrastructure for postprocessing 10-bit
formats, store VP9 bit depth in context.
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently chroma offset calculation assumes only 1 byte per luma, with
no consideration for stride.
Take necessary information from destination pixel format which makes
calculation completely universal.
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some postproc legacy registers were set in VP9 code. Move them to
postproc and fix their value.
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When allocating aux buffers for postprocessing, it's assumed that base
buffer size is the same as that of output. Coincidentally, that's true
most of the time, but not always. 10-bit source also needs aux buffer
size which is appropriate for 10-bit native format, even if the output
format is 8-bit. Similarly, mv sizes and other extra buffer size also
depends on source width/height, not destination.
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for supporting 10-bit formats, add mechanism which will
filter formats based on pixel depth.
Hantro G2 supports only one decoding format natively and that is based
on bit depth of current video frame. Additionally, it makes no sense to
upconvert bitness, so filter those out too.
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'F.7.3.6.1 General slice segment header syntax' section of HEVC
specification describes that a slice header always end aligned on
byte boundary, therefore we only need to provide the data offset in bytes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of bits to skip in the slice header can be computed
in the driver by using sps, pps and decode_params information.
This makes it possible to remove Hantro dedicated control.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make explicit that V4L2_CID_STATELESS_HEVC_SLICE_PARAMS control is
a dynamic array control type.
Some drivers may be able to receive multiple slices in one control
to improve decoding performance.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The HEVC specification describes the following:
"PicOrderCntVal is derived as follows:
PicOrderCntVal = PicOrderCntMsb + slice_pic_order_cnt_lsb
The value of PicOrderCntVal shall be in the range of
−2^31 to 2^31 − 1, inclusive."
To match with these definitions change __u16 pic_order_cnt[2]
into __s32 pic_order_cnt_val.
Change v4l2_ctrl_hevc_slice_params->slice_pic_order_cnt to __s32 too.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 1f82f2df52 ("media: hantro: Enable H.264 on Rockchip VDPU2")
enabled H.264 on some SoCs with VDPU2 cores. This had the side-effect
of exposing H.264 coded format as supported on RK3399.
Fix this and clarify how the codec is explicitly disabled on RK3399 on
this driver.
Fixes: 1f82f2df52 ("media: hantro: Enable H.264 on Rockchip VDPU2")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
None of the shared helpers are used anymore. Make this official by
dropping inclusion of imx-media.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The only event that the driver allows subscribing to,
V4L2_EVENT_IMX_FRAME_INTERVAL_ERROR, is never generated. Drop events
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Inline the imx7_csi_enum_pixel_formats() function in its only caller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver won't accept unsupported pixel formats, there's thus no need
to validate it in imx7_csi_pad_link_validate().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The device supports 14-bit greyscale formats the same way it supports
14-bit Bayer formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The list of supported formats comes from helpers shared with the i.MX6
IPUv3 and is incorrect in multiple regards:
- 10-, 12- and 14-bit Bayer formats are stored in memory as SBGGR10,
SBGGR12 and SBGGR14 respectively (plus components permutations), not
SBGGR16. Same thing for greyscale formats.
- 16-bit RAW formats are not supported by the hardware.
Fix the supported formats table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When trying a format on the video node, if the requested pixel format
isn't supported, fallback to the default with a simpler logic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Inline the imx7_csi_init_mbus_fmt() function in its only caller. This
allows simplifying the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx7_csi_pixfmt cycles field is never used nor set, the bayer field
is never used, and the planar field is never set. Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
All the format lookup functions are called with a ANY selector, drop
selector support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When trying a format on the subdev sink pad, if the requested media bus
code isn't supported, fallback to the default with a simpler logic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Define a macro for the default media bus code and use it through the
driver to replace a hardcoded value and a dynamic query from the
pixel_formats table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the same default image width and height for both the CSI subdev and
the video node to achieve a consistent default through the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A large number of formats defined in the pixel_formats array are not
supported, as shown by the switch-case check in
imx7_csi_pad_link_validate(). Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The formats specific to the IPUv3 are not supported by the CSI bridge.
Drop them, along with the related code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx7_csi_try_colorimetry() function supports the unrelated image
converter hardware as it originates from shared helpers. Drop that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the enum ipu_color_space cs field in struct imx7_csi_pixfmt with
a bool yuv field. This decouples the driver from the unrelated IPUv3
headers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To prepare for code refactoring, copy the format helpers used by this
driver from imx-media-utils.c. Rename structures and functions to avoid
name clashes, no functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel memory allocators already complain loudly to the log when
allocation fails. There's no need for an additional message.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Decouple from the IMX7_CSI_VIDEO_DEF_PIX_WIDTH,
IMX7_CSI_VIDEO_DEF_PIX_HEIGHT and IMX_MEDIA_EOF_TIMEOUT macros defined
in shared helpers by duplicating them in the imx7-media-csi driver, with
a rename to avoid name clashes. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Decouple from the imx_media_dma_buf structure defined in shared helpers
by duplicating it in the imx7-media-csi driver, along with the two small
alloc and free functions. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the subdev pointer stored in platform drv data with the imx7_csi
pointer. Drop a now redundant dev_set_drvdata() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the driver doesn't use any helper that relies on the
imx_media_video_dev structure anymore, merge its fields directly in the
imx7_csi structure. Update all the users accordingly, and drop the list
field that isn't used by the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Decouple from the imx_media_buffer structure defined in shared helpers
by duplicating it in the imx7-media-csi driver. No functional change
intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the driver doesn't use any helper that relies on the
imx_media_dev structure anymore, merge the three fields of the
imx_media_dev structure directly in the imx7_csi structure. Update all
the users accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
