Add device-tree bindings for the ARM CCI-400 on Exynos5420. There
are two slave interfaces: one for the A15 cluster and one for the
A7 cluster.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add generic cluster power control functions for exynos based SoCS
for cluster power up/down and to know the cluster status.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use generic exynos cpu power control functions to power up/down
and to know the status of the cpu in platsmp and hotplug code.
Signed-off-by: Leela Krishna Amudala <leela.krishna@linaro.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add generic cpu power control functions for exynos based
SoCS for cpu power up/down and to know the cpu status.
Signed-off-by: Leela Krishna Amudala <leela.krishna@linaro.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The attached change significantly improves the performance of the LWS-CAS code
in syscall.S.
This allows a number of packages to build (e.g., zeromq3, gtest and libxs)
that previously failed because slow LWS-CAS performance under contention. In
particular, interrupts taken while the lock was taken degraded performance
significantly.
The change does the following:
1) Disables interrupts around the CAS operation, and
2) Changes the loads and stores to use the ordered completer, "o", on
PA 2.0. "o" and "ma" with a zero offset are equivalent. The latter is
accepted on both PA 1.X and 2.0.
The use of ordered loads and stores probably makes no difference on all
existing hardware, but it seemed pedantically correct. In particular, the CAS
operation must complete before LDCW lock is released. As written before, a
processor could reorder the operations.
I don't believe the period interrupts are disabled is long enough to
significantly increase interrupt latency. For example, the TLB insert code is
longer. Worst case is a memory fault in the CAS operation.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
Ratelimit printing of userspace segfaults and make it runtime
configurable via the /proc/sys/debug/exception-trace variable. This
should resolve syslog from growing way too fast and thus prevents
possible system service attacks.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC: stable@vger.kernel.org # v2.6.34+
This patch adds the device tree to support Toradex Colibri T30, a
computer on module which can be used on different carrier boards.
The module consists of a Tegra 30 SoC, two PMIC, DDR3L RAM, eMMC,
a LM95245 temperature sensor and an AX88772B USB Ethernet
Controller. Furthermore, there is a STMPE811 and SGTL5000 audio
codec which are not yet supported. Anything that is not self
contained on the module is disabled by default.
The device tree for the Evaluation Board includes the modules
device tree and enables the supported pheripherials of the carrier
board (the Evaluation Board supports almost all of them).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Change introduced by 88e48d7b33
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.
However change brought by be1db4f661
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.
Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.
Reported-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.
Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.
This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.
Fix this by releasing the primary_if in batadv_frag_send_packet().
Introduced by ee75ed8887
("batman-adv: Fragment and send skbs larger than mtu")
Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.
Introduced in cb1c92ec37
("batman-adv: add debugfs support to view multiif tables").
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Add the corresponding trace if we have a full match in a non-terminal
rule. Note that the traces will look slightly different than in
x_tables since the log message after all expressions have been
evaluated (contrary to x_tables, that emits it before the target
action). This manifests in two differences in nf_tables wrt. x_tables:
1) The rule that enables the tracing is included in the trace.
2) If the rule emits some log message, that is shown before the
trace log message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The vb2 queue timestamp_flags field must be set by drivers, as enforced
by a WARN_ON in vb2_queue_init. The UVC gadget driver failed to do so.
This resulted in the following warning.
[ 2.104371] g_webcam gadget: uvc_function_bind
[ 2.105567] ------------[ cut here ]------------
[ 2.105567] ------------[ cut here ]------------
[ 2.106779] WARNING: CPU: 0 PID: 1 at drivers/media/v4l2-core/videobuf2-core.c:2207 vb2_queue_init+0xa3/0x113()
Fix it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The UVC gadget driver doesn't support interlaced video but left the
buffer field uninitialized. Set it to V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The wall time clock isn't useful for applications as it can jump around
due to time adjustement. Switch to the monotonic clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last reason for static memory mapping is the HBI (board
identification number) check early in the machine code.
Moving the check to the sysreg driver makes it possible to
completely remove the early mapping and init functions.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
As all cores must be properly described in the Device Tree,
there is no point in getting their numbers from SCU on
A5/A9 platforms. This significantly simplifies the code,
removing the need for flat-tree scanning and early static
mapping.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
arm_dt_init_cpu_maps parses the device tree, validates and sets the
cpu_possible_mask appropriately. It is unnecessary to do another DT
parse to get the number of cpus, use num_possible_cpus instead.
This patch also removes setting cpu_present_mask as platforms should
only re-initialize it in smp_prepare_cpus() if present != possible.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch adds a trival sched clock source using free
running, 24MHz clocked counter present in the ARM Ltd.
reference platforms (Versatile, RealView, Versatile
Express) System Registers block.
This code replaces the call in the VE machine code.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Move the Kconfig entry for Versatile (& Express) clock drivers
into a separate file and add individual options for sp810
and vexpress_osc drivers, as they are optional in some
configurations and may have separate dependencies.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:
* LEDs code has been completely removed and replaced with
"gpio-leds" nodes in the tree (referencing dedicated
GPIO subnodes in sysreg - bindings documentation updated);
this also better fits the reality as some variants of the
motherboard don't have all the LEDs populated
* syscfg bridge code has been extracted into a separate
driver (placed in drivers/misc for no better place)
* all the ID & MISC registers are defined as sysconf
making them available for other drivers should they need
to use them (and also to the user via /sys/kernel/debug/regmap
which can be helpful in platform debugging)
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Define syscon platform data structure that can be used
to define a regmap config name. This is particularly useful
in the regmap debugfs when there is more than one syscon
device registered, to distinguish the register blocks.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
In "Device Tree powered" systems, platform devices are usually massively
populated with of_platform_populate() call, executed at some level of
initcalls, either by generic architecture or by platform-specific code.
There are situations though where certain devices must be created (and
bound with drivers) before all the others. This presents a challenge,
as devices created explicitly would be created again by
of_platform_populate().
This patch tries to solve that issue in a generic way, adding a
"populated" flag for a DT node description. Subsequent
of_platform_populate() will skip such nodes (and its children) in
a similar way to the non-available ones.
This patch also adds of_platform_depopulate() as an operation
complementary to the _populate() one. It removes a platform or an amba
device populated from the Device Tree, together with its all children
(leaving, however, devices without associated of_node untouched)
clearing the "populated" flag on the way.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
I managed to drop a change to stream ID setting from commit 49fee17816
("ASoC: Intel: Only export one Baytrail DAI") leading to non-working
simultaneous capture-playback since after one DAI conversion
rtd->cpu_dai->id + 1 will be the same for both playback and capture.
Use substream->stream + 1 like it was in original Liam's patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
adding new device id for SMSC USB334x devices.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some circumstances when g_audio is being unloaded there happens
an endless loop in udc driver. It has happend on a board with
s3c-hsotg. If there are requests in endpoint's queue, they are completed
in a loop. But completing them might cause appending new requests
to the queue. This patch causes agdev_iso_complete() to return immediately
if request's status is -ESHUTDOWN. If it does not return immediately,
then although the current request is removed from the queue, a new one
is appended to the queue, so the above mentioned loop cannot end.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Select the MFD_SUN6I_PRCM option when sun6i arch is enabled in order to get
the PRCM (Power/Reset/Clock Management) related drivers compiled.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This fixes a bug when dwc3_pci_register_phys() fails and leaves device enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
First usage of ret variable will re-write initial value. Thus, there is no need
to initialize it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
_PAGE_IOMAP is used in xen_remap_domain_mfn_range() to prevent the
pfn_pte() call in remap_area_mfn_pte_fn() from using the p2m to translate
the MFN. If mfn_pte() is used instead, the p2m look up is avoided and
the use of _PAGE_IOMAP is no longer needed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
PCI devices may have BARs located above the end of RAM so mark such
frames as identity frames in the p2m (instead of the default of
missing).
PFNs outside the p2m (above MAX_P2M_PFN) are also considered to be
identity frames for the same reason.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In xen_add_extra_mem(), if the WARN() checks for bad MFNs trigger it is
likely that they will trigger at lot, spamming the log.
Use WARN_ONCE() instead.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Large (multi-GB) identity ranges currently require a unique middle page
(filled with p2m_identity entries) per 1 GB region.
Similar to the common p2m_mid_missing middle page for large missing
regions, introduce a p2m_mid_identity page (filled with p2m_identity
entries) which can be used instead.
set_phys_range_identity() thus only needs to allocate new middle pages
at the beginning and end of the range.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Allow set_phys_range_identity() to work with a range that overlaps
MAX_P2M_PFN by clamping pfn_e to MAX_P2M_PFN.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
early_p2m_alloc_middle() allocates a new leaf page and
early_p2m_alloc() allocates a new middle page. This is confusing.
Swap the names so they match what the functions actually do.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Execution is not going to continue after telling Xen about the crash.
Let other panic notifiers run by postponing the final hypercall as much
as possible.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Make the CONFIG_OF=n prototpe of of_node_full_name() mateh the CONFIG_OF=y
version.
Fixes compile warnings like this:
sound/soc/soc-core.c: In function 'soc_check_aux_dev':
sound/soc/soc-core.c:1667:3: warning: passing argument 1 of 'of_node_full_name' discards 'const' qualifier from pointer target type [enabled by default]
codecname = of_node_full_name(aux_dev->codec_of_node);
when CONFIG_OF is not defined.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
PSCIv0.2 adds a new function called AFFINITY_INFO, which
can be used to query if a specified CPU has actually gone
offline. Calling this function via cpu_kill ensures that
a CPU has quiesced after a call to cpu_die. This helps
prevent the CPU from doing arbitrary bad things when data
or instructions are clobbered (as happens with kexec)
in the window between a CPU announcing that it is dead
and said CPU leaving the kernel.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The PSCI v0.2+ spec defines standard values for PSCI function IDs.
Add a new binding entry so that pre v0.2 implementations can
use DT entries for function IDs and v0.2+ implementations use
standard entries as defined by the PSCIv0.2 specification.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The PSCIv0.2 spec defines standard values of function IDs
and introduces a few new functions. Detect version of PSCI
and appropriately select the right PSCI functions.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
with the right capability number. irqfd for s390x was
introduced with 3.15-rc1, so this fix should still go into
Linus tree for 3.15
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uARM
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-for-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
Here is a fix that aligns the irqfd code changes for 3.15
with the right capability number. irqfd for s390x was
introduced with 3.15-rc1, so this fix should still go into
Linus tree for 3.15
* acpi-video:
ACPI / video: correct DMI tag for Dell Inspiron 7520
ACPI / video: Add use_native_backlight quirks for more systems
* acpi-blacklist:
ACPI / blacklist: Add dmi_enable_osi_linux quirk for Asus EEE PC 1015PX
ACPI: blacklist win8 OSI for Dell Inspiron 7737
* acpi-ac:
ACPI: Revert "ACPI / AC: convert ACPI ac driver to platform bus"
* acpi-proc:
ACPI / proc: Do not say when /proc interfaces will be deleted in Kconfig
ACPI: Revert "ACPI / Battery: Remove battery's proc directory"
ACPI: Revert "ACPI: Remove CONFIG_ACPI_PROCFS_POWER and cm_sbsc.c"
* acpica:
ACPICA: Tables: Restore old behavor to favor 32-bit FADT addresses.
ACPICA: Tables: Fix invalid pointer accesses in acpi_tb_parse_root_table().
* acpi-tpm:
ACPI / TPM: Fix resume regression on Chromebooks
* acpi-processor:
ACPI / processor: do not mark present at boot but not onlined CPU as onlined
On SNB the BIOS provided WM memory latency values seem insufficient to
handle high resolution displays.
In this particular case the display mode was a 2560x1440@60Hz, which
makes the pixel clock 241.5 MHz. It was empirically found that a memory
latency value if 1.2 usec is enough to avoid underruns, whereas the BIOS
provided value of 0.7 usec was clearly too low. Incidentally 1.2 usec
is what the typical BIOS provided values are on IVB systems.
Increase the WM memory latency values to at least 1.2 usec on SNB.
Hopefully this won't have a significant effect on power consumption.
v2: Increase the latency values regardless of the pixel clock
Cc: Robert N <crshman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70254
Tested-by: Robert Navarro <crshman@gmail.com>
Tested-by: Vitaly Minko <vitaly.minko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
