Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Resolves compile warning about use of a deprecated function call:
drivers/net/ethernet/amd/nmclan_cs.c: In function ‘nmclan_config’:
drivers/net/ethernet/amd/nmclan_cs.c:624:3: warning: ‘pcmcia_request_exclusive_irq’ is deprecated (declared at include/pcmcia/ds.h:213) [-Wdeprecated-declarations]
ret = pcmcia_request_exclusive_irq(link, mace_interrupt);
Updates pcmcia_request_exclusive_irq() to pcmcia_request_irq().
CC: Roger Pao <rpao@paonet.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot make struct qdisc_skb_cb bigger without impacting IPoIB,
or increasing skb->cb[] size.
Commit e0f31d8498 ("flow_keys: Record IP layer protocol in
skb_flow_dissect()") broke IPoIB.
Only current offender is sch_choke, and this one do not need an
absolutely precise flow key.
If we store 17 bytes of flow key, its more than enough. (Its the actual
size of flow_keys if it was a packed structure, but we might add new
fields at the end of it later)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: e0f31d8498 ("flow_keys: Record IP layer protocol in skb_flow_dissect()")
Signed-off-by: David S. Miller <davem@davemloft.net>
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get more comprehensive and integrated thermal management, it adds ntc
thermistor to thermal framework as a thermal sensor. It's governed thermal
susbsystem only if it is described in DT node. Otherwise, it just notifies
temperature to userspace via sysfs as it used to be.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code
and reduce code size.
Cc: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp103 temperature sensor driver registers with the hwmon framework by calling
hwmon_device_register_with_groups but does not have a .remove method to call
hwmon_device_unregister to unregister from the framework when the device is no
longer needed. Fix this by calling devm_hwmon_device_register_with_groups.
Signed-off-by: Sundar J Dev <sundarjayakumardev@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit 412ca1550c ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).
CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Thibaut Collet <thibaut.collet@6wind.com>
Suggested-by: Thibaut Collet <thibaut.collet@6wind.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ATA drivers need the dma drain size workaround, and thus need to
call blk_mq_start_request before the S/G mapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Moved blk_mq_rq_timed_out() definition to the private blk-mq.h header.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 8cb34819cdd5d(blk-mq: unshared timeout handler) introduces
blk-mq's own timeout handler, and removes following line:
blk_queue_rq_timed_out(q, blk_mq_rq_timed_out);
which then causes blk_add_timer() to bypass adding the timer,
since blk-mq no longer has q->rq_timed_out_fn defined.
This patch fixes the problem by bypassing the check for blk-mq,
so that both request deadlines are still set and the rolling
timer updated.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's not uncommon for crash dump kernels to be limited to 128MB or
something low in that area. This is normally not a problem for
devices as we don't use that much memory, but for some shared SCSI
setups with huge queue depths, it can potentially fill most of
memory with tons of request allocations. blk-mq does scale back
when it fails to allocate memory, but it scales back just enough
so that blk-mq succeeds. This could still leave the system with
not enough memory to make any real progress.
Check if we are in a kdump environment and limit the hardware
queues and tag depth.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch removes two unnecessary blk_clear_rq_complete(),
the REQ_ATOM_COMPLETE flag is cleared inside blk_mq_start_request(),
so:
- The blk_clear_rq_complete() in blk_flush_restore_request()
needn't because the request will be freed later, and clearing
it here may open a small race window with timeout.
- The blk_clear_rq_complete() in blk_mq_requeue_request() isn't
necessary too, even though REQ_ATOM_STARTED is cleared in
__blk_mq_requeue_request(), in theory it still may cause a small
race window with timeout since the two clear_bit() may be
reordered.
Signed-off-by: Ming Lei <ming.lei@canoical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow blk-mq to pass an argument to the timeout handler to indicate
if we're timing out a reserved or regular command. For many drivers
those need to be handled different.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Duplicate the (small) timeout handler in blk-mq so that we can pass
arguments more easily to the driver timeout handler. This enables
the next patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't do a kmalloc from timer to handle timeouts, chances are we could be
under heavy load or similar and thus just miss out on the timeouts.
Fortunately it is very easy to just iterate over all in use tags, and doing
this properly actually cleans up the blk_mq_busy_iter API as well, and
prepares us for the next patch by passing a reserved argument to the
iterator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we've changed the driver API on the submission side use the
opportunity to fix up the name on the completion side to fit into the
general scheme.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we call blk_mq_start_request from the core blk-mq code before calling into
->queue_rq there is a racy window where the timeout handler can hit before we've
fully set up the driver specific part of the command.
Move the call to blk_mq_start_request into the driver so the driver can start
the request only once it is fully set up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pass an explicit parameter for the last request in a batch to ->queue_rq
instead of using a request flag. Besides being a cleaner and non-stateful
interface this is also required for the next patch, which fixes the blk-mq
I/O submission code to not start a time too early.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When requests are retried due to hw or sw resource shortages,
we often stop the associated hardware queue. So ensure that we
restart the queues when running the requeue work, otherwise the
queue run will be a no-op.
Signed-off-by: Jens Axboe <axboe@fb.com>
__blk_mq_alloc_rq_maps() can be invoked multiple times, if we scale
back the queue depth if we are low on memory. So don't clear
set->tags when we fail, this is handled directly in
the parent function, blk_mq_alloc_tag_set().
Reported-by: Robert Elliott <Elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We should not insert requests into the flush state machine from
blk_mq_insert_request. All incoming flush requests come through
blk_{m,s}q_make_request and are handled there, while blk_execute_rq_nowait
should only be called for BLOCK_PC requests. All other callers
deal with requests that already went through the flush statemchine
and shouldn't be reinserted into it.
Reported-by: Robert Elliott <Elliott@hp.com>
Debugged-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch should fix the bug reported in
https://lkml.org/lkml/2014/9/11/249.
We have to initialize at least the atomic_flags and the cmd_flags when
allocating storage for the requests.
Otherwise blk_mq_timeout_check() might dereference uninitialized
pointers when racing with the creation of a request.
Also move the reset of cmd_flags for the initializing code to the point
where a request is freed. So we will never end up with pending flush
request indicators that might trigger dereferences of invalid pointers
in blk_mq_timeout_check().
Cc: stable@vger.kernel.org
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reported-by: Paulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Tested-by: Paulo De Rezende Pinatti <ppinatti@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we start the request, we set the deadline and flip the bits
marking the request as started and non-complete. However, it's
important that the deadline store is ordered before flipping the
bits, otherwise we could have a small window where the request is
marked started but with an invalid deadline. This can confuse the
timeout handling.
Suggested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fixes the following randconfig build failure:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c: In function
> ‘pch_ptp_match’:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c:130:2: error:
> implicit declaration of function ‘ptp_classify_raw’
> [-Werror=implicit-function-declaration]
> if (ptp_classify_raw(skb) == PTP_CLASS_NONE)
> ^
> cc1: some warnings being treated as errors
> make[5]: *** [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.o] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LIBFC depends upon SCSI_FC_ATTRS and select's CRC32C.
The only alternative would be to 'select' CRC32C and all of
SCSI_FC_ATTRS direct and indirect dependencies in the Kconfig section
for every LIBFCOE user which makes little sense.
Subsequently, use 'depends' instead of 'select' for LIBFCOE too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "ROM" and unknown probe types within the obsolete "direct-mapped"
probe function used the nonexistent "mtd_rom" probe instead of the
intended "map_rom".
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We had several problems here. First, a race condition on QP1 mac
handling between mlx4_ib_update_qps and mlx4_ib_modify_qp, which is
fixed by taking the qp mutex in mlx4_ib_update_qps.
Also, qp->pri.smac_port was not updated in mlx4_ib_update_qps.
Last, in __mlx4_ib_modify_qp we did not properly handle the case where
the mac is zero, but port is non-zero.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Automatic Path Migration is not supported under RoCE. Therefore,
return a "not-supported" error if the caller attempts to set an
alternate path in a QP context.
In addition, if there are no IB ports configured, do not report
APM capability in the device flags returned by mlx4_ib_query_device.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For native functions (non-SR-IOV), there's no reason to update
the smac_index, as QP1 is a GSI QP.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The source MAC is needed in RoCE when building the QP1 header.
Currently, this is obtained from the source net device. However, the net
device may not yet exist, or can be destroyed in parallel to this QP1 send
operation (e.g through the VPI port change flow) so accessing it may cause
a kernel crash.
To fix this, we maintain a source MAC cache per port for the net device in
struct mlx4_ib_roce. This cached MAC is initialized to be the default MAC
address obtained during HCA initialization via QUERY_PORT. This cached MAC
is updated via the netdev event notifier handler.
Since the cached MAC is held in an atomic64 object, we do not need locking
when accessing it.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a chance that the VF mlx4 RoCE driver (mlx4_ib) may see a 0-mac
as the current default MAC address when a RoCE interface first comes up.
In this case, the RoCE driver registers the 0-mac to get its MAC index --
used in the INIT2RTR transition when it creates its proxy Q1 qp's.
If we do not allow QP1 to be created, the RoCE driver will not come up.
If we do not register the 0-mac, but simply use a random mac-index,
QP1 will attempt to send packets with an someone's else source MAC which
will get the system into more troubled.
Since a 0-mac was previously used to indicate a free slot, this leads to
errors, both when the 0-mac is registered and when it is unregistered.
The required fix is to check in addition that the slot containing the
0-mac has a reference count of zero.
Additionally, when comparing MAC addresses, need to mask out the 2 MSBs
of the u64 mac on both sides of the comparison.
Note that when the EN driver (mlx4_en) comes up, it set itself a proper
mac --> the RoCE driver gets to be notified on that and further handing
is done with the update qp command, as was added by commit 9433c18891
("IB/mlx4: Invoke UPDATE_QP for proxy QP1 on MAC changes").
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When marsheling a user path to the kernel struct ib_sa_path, need
to zero smac, dmac and set the vlan id to the "no vlan" value.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Reported-by: Aleksey Senin <alekseys@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When device is being removed (e.g during VPI port link type change
from ETH to IB), tasks for gid table changes should not be executed.
Flush the current queue of tasks and block further tasks from entering the queue.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Chuck Lever reported the following stack trace:
=================================
[ INFO: inconsistent lock state ]
3.16.0-rc2-00024-g2e78883 #17 Tainted: G E
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&(&iboe->lock)->rlock){+.?...}, at: [<ffffffffa065f68b>] mlx4_ib_addr_event+0xdb/0x1a0 [mlx4_ib]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810b3110>] mark_irqflags+0x110/0x170
[<ffffffff810b4806>] __lock_acquire+0x2c6/0x5b0
[<ffffffff810b4bd9>] lock_acquire+0xe9/0x120
[<ffffffff815f7f6e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa0661084>] mlx4_ib_scan_netdevs+0x34/0x260 [mlx4_ib]
[<ffffffffa06612db>] mlx4_ib_netdev_event+0x2b/0x40 [mlx4_ib]
[<ffffffff81522219>] register_netdevice_notifier+0x99/0x1e0
[<ffffffffa06626e3>] mlx4_ib_add+0x743/0xbc0 [mlx4_ib]
[<ffffffffa05ec168>] mlx4_add_device+0x48/0xa0 [mlx4_core]
[<ffffffffa05ec2c3>] mlx4_register_interface+0x73/0xb0 [mlx4_core]
[<ffffffffa05c505e>] cm_req_handler+0x13e/0x460 [ib_cm]
[<ffffffff810002e2>] do_one_initcall+0x112/0x1c0
[<ffffffff810e8264>] do_init_module+0x34/0x190
[<ffffffff810ea62f>] load_module+0x5cf/0x740
[<ffffffff810ea939>] SyS_init_module+0x99/0xd0
[<ffffffff815f8fd2>] system_call_fastpath+0x16/0x1b
irq event stamp: 336142
hardirqs last enabled at (336142): [<ffffffff810612f5>] __local_bh_enable_ip+0xb5/0xc0
hardirqs last disabled at (336141): [<ffffffff81061296>] __local_bh_enable_ip+0x56/0xc0
softirqs last enabled at (336004): [<ffffffff8106123a>] _local_bh_enable+0x4a/0x50
softirqs last disabled at (336005): [<ffffffff810617a4>] irq_exit+0x44/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&iboe->lock)->rlock);
<Interrupt>
lock(&(&iboe->lock)->rlock);
*** DEADLOCK ***
The above problem was caused by the spin lock being taken both in the process
context and in a soft-irq context (in a netdev notifier handler).
The required fix is to use spin_lock/unlock_bh() instead of spin_lock/unlock
on the iboe lock.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When a RoCE port becomes active and the netdev of the port has upper
device (e.g bond/team), GIDs derived from the upper dev should appear
in the port's RoCE GID table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no need to reset the gid table twice and we need to do it only
for Ethernet ports. Also, no need to actively scan ndetdevs since it's
being done immediatly after we register netdev notifiers.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When reading the IPv6 addresses from the net-device, make sure to
avoid adding a duplicate entry to the GID table because of equality
between the default GID we generate and the default IPv6 link-local
address of the device.
Fixes: acc4fccf4e ("IB/mlx4: Make sure GID index 0 is always occupied")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When Ethernet netdev is not present for a port (e.g. when the link
layer type of the port is InfiniBand) it's possible to dereference a
null pointer when we do netdevice scanning.
To fix that, we move a section of code that needs to run only when
netdev is present to a proper if () statement.
Fixes: ad4885d279 ("IB/mlx4: Build the port IBoE GID table properly under bonding")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
