LVDS panel, make/model described as:
AU Optronics Corporation - B101XTN01.0 (H/W:0A)
See:
http://www.encore-electronic.com/media/B101XTN01.0.pdf
Tested with panel attached to an Inforce IFC6410 board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull "ARM: LPC32xx: Device tree updates" from Roland Stigge:
This enables ubifs in the lpc32xx defconfig.
* 'lpc32xx/defconfig' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: defconfig update
If we are running in a kdump environment, resources are scarce.
For some SCSI setups with a huge set of shared tags, we run out
of memory allocating what the drivers is asking for. So implement
a scale back logic to reduce the tag depth for those cases, allowing
the driver to successfully load.
We should extend this to detect low memory situations, and implement
a sane fallback for those (1 queue, 64 tags, or something like that).
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The uses of "rcu_assign_pointer()" are NULLing out the pointers.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Link: http://lkml.kernel.org/p/20140822142822.GA32391@ada
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Dave Jones reported seeing a bug from one of my TLB tracepoints:
http://lkml.kernel.org/r/20140806181801.GA4605@redhat.com
I've been running these patches for months and never saw this.
But, a big chunk of my testing, especially with all the debugging
enabled, was in a vm where intel_idle doesn't work. On the
systems where I was using intel_idle, I never had lockdep enabled
and this tracepoint on at the same time.
This patch ensures that whenever we have lockdep available, we do
_some_ RCU activity at the site of the tracepoint, despite
whether the tracepoint's condition matches or even if the
tracepoint itself is completely disabled. This is a bit of a
hack, but it is pretty self-contained.
I confirmed that with this patch plus lockdep I get the same
splat as Dave Jones did, but without enabling the tracepoint
explicitly.
Link: http://lkml.kernel.org/p/20140807175204.C257CAC5@viggo.jf.intel.com
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Dave Jones <davej@redhat.com>,
Cc: paulmck@linux.vnet.ibm.com
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Allowing function callbacks to declare their own trampolines requires
that each ftrace_ops that has a trampoline must have some sort of
accounting that keeps track of which ops has a trampoline attached
to a record.
The easy way to solve this was to add a "tramp_hash" that created a
hash entry for every function that a ops uses with a trampoline.
But since we can have literally tens of thousands of functions being
traced, that means we need tens of thousands of descriptors to map
the ops to the function in the hash. This is quite expensive and
can cause enabling and disabling the function graph tracer to take
some time to start and stop. It can take up to several seconds to
disable or enable all functions in the function graph tracer for this
reason.
The better approach albeit more complex, is to keep track of how ops
are being enabled and disabled, and use that along with the counting
of the number of ops attached to records, to determive what ops has
a trampoline attached to a record at enabling and disabling of
tracing.
To do this, the tramp_hash has been replaced with an old_filter_hash
and old_notrace_hash, which get the copy of the ops filter_hash and
notrace_hash respectively. The old hashes is kept until the ops has
been modified or removed and the old hashes are used with the logic
of the accounting to determine the ops that have the trampoline of
a record. The reason this has less of a footprint is due to the trick
that an "empty" hash in the filter_hash means "all functions" and
an empty hash in the notrace hash means "no functions" in the hash.
This is much more efficienct, doesn't have the delay, and takes up
much less memory, as we do not need to map all the functions but
just figure out which functions are mapped at the time it is
enabled or disabled.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add three new flags for ftrace_ops:
FTRACE_OPS_FL_ADDING
FTRACE_OPS_FL_REMOVING
FTRACE_OPS_FL_MODIFYING
These will be set for the ftrace_ops when they are first added
to the function tracing, being removed from function tracing
or just having their functions changed from function tracing,
respectively.
This will be needed to remove the tramp_hash, which can grow quite
big. The tramp_hash is used to note what functions a ftrace_ops
is using a trampoline for. Denoting which ftrace_ops is being
modified, will allow us to use the ftrace_ops hashes themselves,
which are much smaller as they have a global flag to denote if
a ftrace_ops is tracing all functions, as well as a notrace hash
if the ftrace_ops is tracing all but a few. The tramp_hash just
creates a hash item for every function, which can go into the 10s
of thousands if all functions are using the ftrace_ops trampoline.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When dumping the enabled_functions, use the first op that is
found with a trampoline to the record, as there should only be
one, as only one ops can be registered to a function that has
a trampoline.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_hash_move() currently frees the old hash that is passed to it
after replacing the pointer with the new hash. Instead of having the
function do that chore, have the caller perform the free.
This lets the ftrace_hash_move() be used a bit more freely, which
is needed for changing the way the trampoline logic is done.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The clean up that adds the helper function ftrace_ops_get_func()
caused the default function to not change when DYNAMIC_FTRACE was not
set and no ftrace_ops were registered. Although static tracing is
not very useful (not having DYNAMIC_FTRACE set), it is still supported
and we don't want to break it.
Clean up the if statement even more to specifically have the default
function call ftrace_stub when no ftrace_ops are registered. This
fixes the small bug for static tracing as well as makes the code a
bit more understandable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When RANDOMIZE_BASE (KASLR) is enabled; or the sum of all loaded
modules exceeds 512 MiB, then loading modules fails with a warning
(and hence a vmalloc allocation failure) because the PTEs for the
newly-allocated vmalloc address space are not zero.
WARNING: CPU: 0 PID: 494 at linux/mm/vmalloc.c:128
vmap_page_range_noflush+0x2a1/0x360()
This is caused by xen_setup_kernel_pagetables() copying
level2_kernel_pgt into level2_fixmap_pgt, overwriting many non-present
entries.
Without KASLR, the normal kernel image size only covers the first half
of level2_kernel_pgt and module space starts after that.
L4[511]->level3_kernel_pgt[510]->level2_kernel_pgt[ 0..255]->kernel
[256..511]->module
[511]->level2_fixmap_pgt[ 0..505]->module
This allows 512 MiB of of module vmalloc space to be used before
having to use the corrupted level2_fixmap_pgt entries.
With KASLR enabled, the kernel image uses the full PUD range of 1G and
module space starts in the level2_fixmap_pgt. So basically:
L4[511]->level3_kernel_pgt[510]->level2_kernel_pgt[0..511]->kernel
[511]->level2_fixmap_pgt[0..505]->module
And now no module vmalloc space can be used without using the corrupt
level2_fixmap_pgt entries.
Fix this by properly converting the level2_fixmap_pgt entries to MFNs,
and setting level1_fixmap_pgt as read-only.
A number of comments were also using the the wrong L3 offset for
level2_kernel_pgt. These have been corrected.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
This patch adds the devicetree documentation for the Mediatek UART.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device has a highspeed register which influences the calcualtion
of the divisor. The chip lacks support for some baudrates. When requested,
we set the divisor to the next smaller baudrate and adjust the c_cflag
accordingly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The architectures supported by this driver, arm and sh, have expensive
implementations of writel(), reliant on spin locks and explicit L2 cache
management. These architectures provide a cheaper writel_relaxed() which
is much better suited to peripherals that do not perform DMA. The
situation with readl()/readl_relaxed()is similar although less acute.
This driver does not use DMA and will be more power efficient and more
robust (due to absence of spin locks during console I/O) if it uses the
relaxed variants.
The driver supports COMPILE_TEST and therefore falls back to writel()
when writel_relaxed() does not exist.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: kernel@stlinux.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0dcaa2499b improved error
handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req"
should be placed after "pm_runtime_disable(&pdev->dev)".
Signed-off-by: Xiang Wang <wangx@marvell.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I am leaving Samsung, so my current e-mail address is not going to work
any longer. Replace it with my private one. In addition, Sylwester
Nawrocki is being added as co-maintainer for Samsung clock drivers to
take some of the responsibilities, as I will be doing my part in my spare
time.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the IRQCHIP_SKIP_SET_WAKE flag to baytrail gpio irq_chip
to resolve unbalaced IRQ wake disable warnings.
Suggested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix ERROR: "devm_regmap_init_i2c" [drivers/regulator/isl9305.ko] undefined!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ATH10K_DEBUGFS must depend on DEBUG_FS, otherwise
ath10k will generate an invalid pointer on module load.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On 32bit systems the bitmap was too small and it
was overwritten partially by the stat completion
structure. This was visible with 10.2 firmware
only due to it using a few of the last service
ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 7c7b9cf53d ("ASoC: simple-card: fixup cpu_dai_name
clear case") changed the way that "sound-dai" properties are handled,
which leads to the clock frequency not being picked up from the
node that the phandle points to, as correctly identified by gcc
with this warning:
sound/soc/generic/simple-card.c: In function 'asoc_simple_card_sub_parse_of':
sound/soc/generic/simple-card.c:165:7: warning: 'node' may be used uninitialized in this function [-Wmaybe-uninitialized]
This restores the previous behavior by using the node from
of_parse_phandle_with_args() that was previously being
returned from of_parse_phandle().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dpcm_path_get may return -ENOMEM when allocating memory for list
fails. We should not keep processing path or start up dpcm dai in
this case.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These of_node_get() were added to balance refcount decrements inside of
of_find_node_by_name().
See: commit c92f5dd2c4 ("regulator: Add missing of_node_put()")
However of_find_node_by_name() was then replaced by of_get_child_by_name(),
which doesn't call of_node_put() against its input parameter.
So, need to remove these unnecessary of_node_get() calls.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The old handling of prefix pages was broken in the diag10 ballooner.
We now rely on gmap_discard to check for start > end and do a
slow path if the prefix swap pages are affected:
1. discard the pages from start to prefix
2. discard the absolute 0 pages
3. discard the pages after prefix swap to end
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Due to the earlier check we know that ipte_lock_count must be 0.
No need to add a useless if. Let's make clear that we are going
to always wakeup when we execute that code.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
We must not fallthrough if the conditions for external call are not met.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Currently we fill up a full 5 level page table to hold the guest
mapping. Since commit "support gmap page tables with less than 5
levels" we can do better.
Having more than 4 TB might be useful for some testing scenarios,
so let's just limit ourselves to 16TB guest size.
Having more than that is totally untested as I do not have enough
swap space/memory.
We continue to allow ucontrol the full size.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
We now propagate interrupt injection errors back to the ioctl. We
should mark functions that might fail with __must_check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
We have to provide a per guest crypto block for the CPUs to
enable MSA4 instructions. According to icainfo on z196 or
later this enables CCM-AES-128, CMAC-AES-128, CMAC-AES-192
and CMAC-AES-256.
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split MSA4/protected key into two patches]
This patch removes the unused asm/rwlock.h and rwlock.S files.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1408037251-45918-3-git-send-email-Waiman.Long@hp.com
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Francesco Fusco <ffusco@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Graf <tgraf@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As the x86 architecture now uses qrwlock for its read/write lock
implementation, it is no longer necessary to keep the old rwlock code
around. This patch removes the old rwlock code in the asm/spinlock.h
and asm/spinlock_types.h files. Now the ARCH_USE_QUEUE_RWLOCK
config parameter cannot be removed from x86/Kconfig or there will be
a compilation error.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/r/1408037251-45918-2-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The patch folding the atomic ops had a silly fail in the _return primitives.
Fixes: 4f3316c2b5 ("locking,arch,sparc: Fold atomic_ops")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140902094016.GD31157@worktop.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
