There is no need to keep FSF address in the head of the file. While here, fix
few typos in the header.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The downstream ChromeOS 3.8 kernel sets the clock frequency
for the I2C bus 7 at 400kHz. Do the same change in mainline.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5420 based Peach Pit and the Exynos5800 based Peach Pi
machines have an i2c ISL29018 light sensor. This patch adds the
device nodes needed to support this device.
These DTS snippets were taken from the downstream Chrome OS 3.8
kernel Device Tree for Peach Pit and Pi boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch creates a thermistor fragment carrying the NTC
Thermistor nodes as children of the IIO based ADC.
This fragment is included in exynos5420-peach-pit.dts and
exynos5800-peach-pi.dts.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding regulators for hdmi for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding regulators for HDMI for Peach-pi board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 based Peach Pit and Exynos5800 based Peach Pi boards
uses a Maxim 77802 power management IC to drive regulators and
its Real Time Clock. This patch adds support for this chip.
These are the device nodes and pinctrl configuration that
are present on the Peach pit DeviceTree source file in the
the Chrome OS kernel 3.8 tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sun4i-apb0 clock, as found on all platforms using it, is a
power-of-two-based divider clock, with a special divider of 2
for value 0.
This was causing the clock framework to incorrectly calculate
the clock rate for apb1 and related modules on sun6i and sun8i.
On sun[4/5/7]i, u-boot SPL configures the divider with value 1
for /2 divider, so no suprises there.
This patch adds a proper divider table for it, so the correct
clock rate can be calculated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
4283c70e91 ("PCI: pciehp: Make pcie_wait_cmd() self-contained") added
a cache of the most recent command written to the Slot Control register.
This register is only 16 bits wide, but the cache ("slot_ctrl") is 32 bits.
Reduce slot_ctrl to a u16 so it matches the register size. No functional
change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There's not really a good way to determine whether firmware has already
configured a device with _HPP/_HPX settings. On legacy systems, the BIOS
has probably configured everything, but on UEFI systems it is not required
to do so.
Per the PCI Firmware Specification, rev 3.1, sec 3.5, if PCI_COMMAND_IO or
PCI_COMMAND_MEMORY is set, we can assume firmware has set the corresponding
BARs and maybe we can assume it has configured the rest of the device. And
if a bridge has PCI_COMMAND_PARITY or PCI_COMMAND_SERR set, we can assume
firmware has configured the bridge. But we can't tell much about devices
without BARs.
I think it should be safe to apply _HPP and _HPX settings anyway, even if
firmware has already configured the device, so configure everything we
find.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Linux manages MPS and MRRS settings to keep them consistent across the PCIe
fabric. BIOS doesn't participate in this Linux management, so ignore that
part of any _HPX settings it supplies.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
We currently apply _HPP settings only to:
- non-bridge devices, and
- PCI-to-PCI bridges
i.e., we do not apply them to PCI-to-ISA bridges and the like. It has been
that way since _HPP support was added by 40abb96c51 ("pciehp: Fix
programming hotplug parameters"), but I don't think there's any reason to
exclude these other bridges.
Apply _HPP settings to hot-added PCI devices of any type.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Do not clear PCI_COMMAND_SERR or PCI_COMMAND_PARITY based on _HPP. The
spec (ACPI rev 5.0, sec 6.2.7) says that when "Enable SERR" is set to 1,
we should enable SERR in the command register. It says nothing about
*disabling* SERR or PERR; in fact, the example in 6.2.7.1 says we should
leave PERR alone unless "Enable PERR" is 1.
For hot-added devices, this probably doesn't matter because they power up
with these bits cleared. But in addition to hot-plugged devices, the spec
allows the platform to use _HPP for "configuration of PCI devices not
configured by the BIOS at system boot," and it may make a difference for
devices present at boot.
This change means that if BIOS enables SERR or PERR on a device, and it
supplies _HPP or _HPX with the SERR or PERR bits *cleared*, we will now
leave SERR or PERR reporting enabled on that device instead of disabling it
as we previously did.
See also 40abb96c51 ("pciehp: Fix programming hotplug parameters"), where
this code was first added.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The ACPI _HPP method was defined before PCIe existed, so its documentation
only mentions PCI. The _HPX Type 0 setting record is essentially identical
to _HPP, but the spec (ACPI rev 5.0, sec 6.2.8.1) says it should be applied
to PCI, PCI-X, and PCIe devices, with settings being ignored if they are
not applicable.
Some platforms with both conventional PCI and PCIe devices provide only
_HPP (not _HPX), so treat _HPP the same way as an _HPX Type 0 record and
apply it to PCIe devices as well as PCI and PCI-X.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
All pci_configure_slot() uses have been removed, so remove the definition
as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
We now configure each PCI device as it is enumerated, in pci_device_add(),
so remove the configuration done in acpiphp.
That configuration, in pci_configure_device(), does not include the
MPS/MRRS configuration done by pcie_bus_configure_settings(), so keep
that here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
We now configure each PCI device as it is enumerated, in pci_device_add(),
so remove the configuration done in shpchp.
That configuration, in pci_configure_device(), does not include the
MPS/MRRS configuration done by pcie_bus_configure_settings(), so keep
that here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
We now configure each PCI device as it is enumerated, in pci_device_add(),
so remove the configuration done in pciehp.
That configuration, in pci_configure_device(), does not include the
MPS/MRRS configuration done by pcie_bus_configure_settings(), so keep
that here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Some platforms can tell the OS how to configure PCI devices, e.g., how to
set cache line size, error reporting enables, etc. ACPI defines _HPP and
_HPX methods for this purpose.
This configuration was previously done by some of the hotplug drivers using
pci_configure_slot(). But not all hotplug drivers did this, and per the
spec (ACPI rev 5.0, sec 6.2.7), we can also do it for "devices not
configured by the BIOS at system boot."
Move this configuration into the PCI core by adding pci_configure_device()
and calling it from pci_device_add(), so we do this for all devices as we
enumerate them.
This is based on pci_configure_slot(), which is used by hotplug drivers.
I omitted:
- pcie_bus_configure_settings() because it configures MPS and MRRS, which
requires global knowledge of the fabric and must be done later, and
- configuration of subordinate devices; that will happen when we call
pci_device_add() for those devices.
Because pci_configure_slot() was only done by hotplug drivers, this initial
version of pci_configure_device() only configures hot-added devices,
ignoring anything added during boot.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Move pci_configure_slot() and related functions from
drivers/pci/hotplug/pcihp_slot to drivers/pci/probe.c.
This is to prepare for doing device configuration during the normal
enumeration process instead of just after hot-add.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move code around to put all the ACPI power management stuff together and
all the pieces related to ACPI methods (_CBA, _HPP, _HPX) together.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_get_hp_params() and related functions from
drivers/pci/hotplug/acpi_pcihp.c to drivers/pci/pci-acpi.c.
Previously, pci_get_hp_params() was used only by hotplug drivers. But
future changes will move this into the normal device enumeration process,
so it will be used even when CONFIG_HOTPLUG_PCI is not set.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We configure cache line size and other settings of hot-added devices, e.g.,
based on ACPI _HPP or _HPX methods. Previously we skipped this for display
devices, but ACPI rev 5.0, sec 6.2.7 and 6.2.8 have no requirement to skip
them.
Remove the check so we configure display devices the same way we configure
other devices.
See also ac81860ea0 ("PCI: hotplug: pciehp: Removed check for hotplug of
display devices").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The ftrace_enabled variable is set to zero in the self tests to keep
delayed functions from being traced and messing with the checks. This
only needs to be done when the checks are being performed, otherwise,
if ftrace_enabled is off when calls back to the utility that is being
tested, it can cause errors to happen and the tests can fail with
false positives.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the last ftrace_ops is unregistered, all the function records should
have a zeroed flags value. Make sure that is the case when the last ftrace_ops
is unregistered.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWAc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen ARM bugfix from Stefano Stabellini:
"The patches fix the "xen_add_mach_to_phys_entry: cannot add" bug that
has been affecting xen on arm and arm64 guests since 3.16. They
require a few hypervisor side changes that just went in xen-unstable.
A couple of days ago David sent out a pull request with a few other
Xen fixes (it is already in master). Sorry we didn't synchronized
better among us"
* tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: remove mach_to_phys rbtree
xen/arm: reimplement xen_dma_unmap_page & friends
xen/arm: introduce XENFEAT_grant_map_identity
The matches_pnp_id function from the synaptics driver is useful for other
drivers too. Make it a generic psmouse helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
nstat->multicast refers to received packets, not transmitted as
is returned here. Change it so that received packet stats are
given.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-09-11
Please pull this batch of fixes intended for the 3.17 stream:
For the mac80211 bits, Johannes says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
For the iwlwifi bits, Emmanuel says:
"I re-enable scheduled scan on firmware that contain the fix for
the bug that Linus reported. A few trivial fixes: endianity issues,
the same DTIM period fix that I did in mac80211. Eyal fixes a few
issues we identified with EAPOL, we now send them just as if they were
management frames, this solves interrop issues. Johannes has another
set of trivial fixes, while Luca fixes the way we configure the filters
in the firmware. Last but not least, a new device is added by Oren."
Emmanuel was traveling, resulting in his pull to be a bit larger than
I would have liked to see at this point. FWIW, I have asked Emmanuel
to be much more strict for any more pull requests in this cycle.
In addition to the above, Sujith Manoharan reverts an earlier ath9k
patch. The earlier change was found to allow for the device to sleep
too long and miss beacons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending out a burst of packets across multiple descriptors,
it is sufficient to send one LDC "start" trigger for
the first descriptor, so do not send an LDC "start" for every
pass through vnet_start_xmit. Similarly, it is sufficient to send
one "DRING_STOPPED" trigger for the last dring (and if that
fails, hold off and send the trigger later).
Optimizations to the number of LDC messages helps avoid
filling up the LDC channel with superfluous LDC messages
that risk triggering flow-control on the channel,
and also boosts performance.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlQRT78ACgkQjTAFq1RaXHPWdACeMBxR8SuasImK4tZSMZf7Sw7F
1bkAoJkftw6Aup9IV9uty4xohLb4pVgX
=kha5
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.17-20140911' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-09-11
this is a pull request for the current release cycle of a single patch.
The patch by David Jander fixes a scheduling while atomic problem in the
flexcan driver, that was introduced by me in v3.14-rc6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It will use pr_info_one() to print the version info of the
driver in probe function only once. No need to use the static
variable here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2abb7cdc0d ("udp: Add support for doing checksum unnecessary
conversion") caused napi_gro_cb structs with the "flush" field zero to
take the "udp_gro_receive" path rather than the "set flush to 1" path
that they would previously take. As a result I saw booting from an NFS
root hang shortly after starting userspace, with "server not
responding" messages.
This change to the handling of "flush == 0" packets appears to be
incidental to the goal of adding new code in the case where
skb_gro_checksum_validate_zero_check() returns zero. Based on that and
the fact that it breaks things, I'm assuming that it is unintentional.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Address reference counting issues with sock_queue_err_skb
After looking over the code for skb_clone_sk after some comments made by
Eric Dumazet I have come to the conclusion that skb_clone_sk is taking the
correct approach in how to handle the sk_refcnt when creating a buffer that
is eventually meant to be returned to the socket via the sock_queue_err_skb
function.
However upon review of other callers I found what I believe to be a
possible reference count issue in the path for handling "wifi ack" packets.
To address this I have applied the same logic that is currently in place so
that the sk_refcnt will be forced to stay at least 1, or we will not
provide an skb to return in the sk_error_queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible issue with the use, or lack thereof of sk_refcnt and
sk_wmem_alloc in the wifi ack status functionality.
Specifically if a socket were to request acknowledgements, and the socket
were to have sk_refcnt drop to 0 resulting in it waiting on sk_wmem_alloc
to reach 0 it would be possible to have sock_queue_err_skb orphan the last
buffer, resulting in __sk_free being called on the socket. After this the
buffer is enqueued on sk_error_queue, however the queue has already been
flushed resulting in at least a memory leak, if not a data corruption.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds some documentation to the call skb_clone_sk. This is
meant to help clarify the purpose of the function for other developers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we try to rmmod the driver for an interface while sockets with
setsockopt(JOIN_ANYCAST) are alive, some refcounts aren't cleaned up
and we get stuck on:
unregister_netdevice: waiting for ens3 to become free. Usage count = 1
If we LEAVE_ANYCAST/close everything before rmmod'ing, there is no
problem.
We need to perform a cleanup similar to the one for multicast in
addrconf_ifdown(how == 1).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani says:
====================
net: arc_emac: fix tx issues
the patches below solve some issues found in the tx ring reclaim
strategy currently implemented in the arc_emac driver.
Without these patches a simple outgoing UDP flow blocks almost
immediately with the socket send buffer full, until some new rx
packets trigger a clean of the tx ring.
Everything seems to work fine on a Radxa Rock with this fix applied.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So here's the header cleanup, rebased on top of drm-next. Two new header
files are created here:
- drivers/gpu/drm/drm_internal.h for non-legacy drm.ko private
declarations.
- include/drm/drm_legacy.h for legacy interfaces used by non-kms drivers.
And of course lots fo stuff gets shuffled into the already existing
drivers/gpu/drm/drm_legacy.h for drm.ko internal stuff.
topic branch smoke-tested in drm-intel-nightly for a bit. And the 0day
tester also worked through it (and found a few places I didn't add a
static to functions).
* tag 'topic/drm-header-rework-2014-09-12' of git://anongit.freedesktop.org/drm-intel:
drm: Move DRM_MAGIC_HASH_ORDER into drm_drv.c
drm: Move drm_class to drm_internal.h
drm: Move LOCK_TEST_WITH_RETURN to <drm/drm_legacy.h>
drm: Move legacy buffer structures to <drm/drm_legacy.h>
drm: Move drm_memory.c map support declarations to <drm/drm_legacy.h>
drm: Purge ioctl forward declarations from drmP.h
drm: unexport drm_global_mutex
drm: Move piles of functions from drmP.h to drm_internal.h
drm: Move vblank related module options into drm_irq.c
drm: Drop drm_sysfs_class from drmP.h
drm: Move __drm_pci_free to drm_legacy.h
drm: Create drm legacy driver header
drm: Move drm_legacy_vma_flush into drm_legacy.h
drm: Move sg functions into drm_legacy.h
drm: Move dma functions into drm_legacy.h
Locks the k_itimer's it_lock member when handling the alarm timer's
expiry callback.
The regular posix timers defined in posix-timers.c have this lock held
during timout processing because their callbacks are routed through
posix_timer_fn(). The alarm timers follow a different path, so they
ought to grab the lock somewhere else.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Avoids sending a signal to alarm timers created with sigev_notify set to
SIGEV_NONE by checking for that special case in the timeout callback.
The regular posix timers avoid sending signals to SIGEV_NONE timers by
not scheduling any callbacks for them in the first place. Although it
would be possible to do something similar for alarm timers, it's simpler
to handle this as a special case in the timeout.
Prior to this patch, the alarm timer would ignore the sigev_notify value
and try to deliver signals to the process anyway. Even worse, the
sanity check for the value of sigev_signo is skipped when SIGEV_NONE was
specified, so the signal number could be bogus. If sigev_signo was an
unitialized value (as it often would be if SIGEV_NONE is used), then
it's hard to predict which signal will be sent.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Returns the time remaining for an alarm timer, rather than the time at
which it is scheduled to expire. If the timer has already expired or it
is not currently scheduled, the it_value's members are set to zero.
This new behavior matches that of the other posix-timers and the POSIX
specifications.
This is a change in user-visible behavior, and may break existing
applications. Hopefully, few users rely on the old incorrect behavior.
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: Richard Larocque <rlarocque@google.com>
[jstultz: minor style tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
timeval_to_jiffies tried to round a timeval up to an integral number
of jiffies, but the logic for doing so was incorrect: intervals
corresponding to exactly N jiffies would become N+1. This manifested
itself particularly repeatedly stopping/starting an itimer:
setitimer(ITIMER_PROF, &val, NULL);
setitimer(ITIMER_PROF, NULL, &val);
would add a full tick to val, _even if it was exactly representable in
terms of jiffies_ (say, the result of a previous rounding.) Doing
this repeatedly would cause unbounded growth in val. So fix the math.
Here's what was wrong with the conversion: we essentially computed
(eliding seconds)
jiffies = usec * (NSEC_PER_USEC/TICK_NSEC)
by using scaling arithmetic, which took the best approximation of
NSEC_PER_USEC/TICK_NSEC with denominator of 2^USEC_JIFFIE_SC =
x/(2^USEC_JIFFIE_SC), and computed:
jiffies = (usec * x) >> USEC_JIFFIE_SC
and rounded this calculation up in the intermediate form (since we
can't necessarily exactly represent TICK_NSEC in usec.) But the
scaling arithmetic is a (very slight) *over*approximation of the true
value; that is, instead of dividing by (1 usec/ 1 jiffie), we
effectively divided by (1 usec/1 jiffie)-epsilon (rounding
down). This would normally be fine, but we want to round timeouts up,
and we did so by adding 2^USEC_JIFFIE_SC - 1 before the shift; this
would be fine if our division was exact, but dividing this by the
slightly smaller factor was equivalent to adding just _over_ 1 to the
final result (instead of just _under_ 1, as desired.)
In particular, with HZ=1000, we consistently computed that 10000 usec
was 11 jiffies; the same was true for any exact multiple of
TICK_NSEC.
We could possibly still round in the intermediate form, adding
something less than 2^USEC_JIFFIE_SC - 1, but easier still is to
convert usec->nsec, round in nanoseconds, and then convert using
time*spec*_to_jiffies. This adds one constant multiplication, and is
not observably slower in microbenchmarks on recent x86 hardware.
Tested: the following program:
int main() {
struct itimerval zero = {{0, 0}, {0, 0}};
/* Initially set to 10 ms. */
struct itimerval initial = zero;
initial.it_interval.tv_usec = 10000;
setitimer(ITIMER_PROF, &initial, NULL);
/* Save and restore several times. */
for (size_t i = 0; i < 10; ++i) {
struct itimerval prev;
setitimer(ITIMER_PROF, &zero, &prev);
/* on old kernels, this goes up by TICK_USEC every iteration */
printf("previous value: %ld %ld %ld %ld\n",
prev.it_interval.tv_sec, prev.it_interval.tv_usec,
prev.it_value.tv_sec, prev.it_value.tv_usec);
setitimer(ITIMER_PROF, &prev, NULL);
}
return 0;
}
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Turner <pjt@google.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Paul Turner <pjt@google.com>
Reported-by: Aaron Jacobs <jacobsa@google.com>
Signed-off-by: Andrew Hunter <ahh@google.com>
[jstultz: Tweaked to apply to 3.17-rc]
Signed-off-by: John Stultz <john.stultz@linaro.org>
In the Dell XPS 13 9333, it appears that sometimes the bus get confused
and corrupts the incoming data. It fills the input report with the
sentinel value "ff". Synaptics told us that such behavior does not comes
from the touchpad itself, so we filter out such reports here.
Unfortunately, we can not simply discard the incoming data because they
may contain useful information. Most of the time, the misbehavior is
quite near the end of the report, so we can still use the valid part of
it.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1123584
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DWC3 glue layer is hardware layer around Synopsys DesignWare
USB3 core. Its purpose is to supply Synopsys IP with required
clocks, voltages and interface it with the rest of the SoC.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit c801e3cc19 ("ipv4: Clarify in docs that accept_local requires rp_filter.").
It is not needed anymore since commit 1dced6a854 ("ipv4: Restore accept_local behaviour in fib_validate_source()").
Suggested-by: Julian Anastasov <ja@ssi.bg>
Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
