Since many omaps run on battery, we should have the battery
drivers enabled. Let's also enable the reset driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some distros are now using systemd, so let's enable most of
what's recommended at:
http://cgit.freedesktop.org/systemd/systemd/tree/README
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
cgroup_pidlist_start() holds cgrp->pidlist_mutex and then calls
pidlist_array_load(), and cgroup_pidlist_stop() releases the mutex.
It is wrong that we release the mutex in the failure path in
pidlist_array_load(), because cgroup_pidlist_stop() will be called
no matter if cgroup_pidlist_start() returns errno or not.
Fixes: 4bac00d16a
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Add rtc node to both the at91sam9g45 SoC family and the at91sam9m10g45ek board.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DSS related pinmux and display data nodes required to support HDMI
and DVI video out on CM-T54.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the IO chain reconfigure fixed, we can now enable the PMIC
scripts for LDP.
Note that at least on my es3.0 based LDP, the UART seems to be
flakey after wake-up events from off-idle and hangs but eventually
continues.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we have support for this in board-rx51-peripherals.c, let's
add it to the .dts files too.
Note that the reset GPIO will eventually go to the driver.
For now let's just pull it down and skip any further reset
in case the bootloader has configured the MAC address so
NFSroot works.
Also note that after 3430-sdp are using proper GPMC timings
we can remove the tests for smsc,lan91c94 in gpmc.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are external pulls on these lines and enabling the
internal pulls can cause issue. This is because the internal
pulls are parallel with the external pulls. So let's clear
the internal I2C pulls.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.
Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compared to legacy booting, we don't have wake-up events enabled
for device tree based booting. This means that if deeper idle
states are enabled, the device won't wake up to UART events and
seems like it has hung.
Let's fix that by adding the wake-up interrupt. Note that we
don't need to set the PIN_OFF_WAKEUPENABLE any longer, that's
handled by the wake-up interrupt when the serial driver does
request_irq on it.
Tested with the following on omap3-overo-summit that has the
ES2.1 omap:
#!/bin/bash
uarts=$(find /sys/class/tty/ttyO*/device/power/ -type d)
for uart in $uarts; do
echo 3000 > $uart/autosuspend_delay_ms
done
uarts=$(find /sys/class/tty/ttyO*/power/ -type d)
for uart in $uarts; do
echo enabled > $uart/wakeup
echo auto > $uart/control
done
echo 1 > /sys/kernel/debug/pm_debug/enable_off_mode
# grep -i uart /proc/interrupts
90: 1085 INTC 74 OMAP UART2
338: 5 pinctrl 366 OMAP UART2
# grep ^core_pwrdm /sys/kernel/debug/pm_debug/count
core_pwrdm (ON),OFF:1654,RET:131,INA:39,ON:1825...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.
And also let's enable thermal as explained by Nishant Menon:
Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.
[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.
Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cc824534d4 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.
As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can only determine the final security level when both pairing request
and response have been exchanged. When initiating pairing the starting
target security level is set to MEDIUM unless explicitly specified to be
HIGH, so that we can still perform pairing even if the remote doesn't
have MITM capabilities. However, once we've received the pairing
response we should re-consult the remote and local IO capabilities and
upgrade the target security level if necessary.
Without this patch the resulting Long Term Key will occasionally be
reported to be unauthenticated when it in reality is an authenticated
one.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This switches the SAMA5D3 to use the new atmel,sama5d3-pinctrl id that was
added with the drive strength options patch.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: second compatible string kept as at91sam9x5]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The atmel_nand driver is now able to handle the nfc clock, add it to sama5d3.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The original code are the same as RB_DECLARE_CALLBACKS().
CC: Michel Lespinasse <walken@google.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 98683650 "Merge branch 'drbd-8.4_ed6' into
for-3.8-drivers-drbd-8.4_ed6" switches to the new augment API, but the
new API requires that the tree is augmented before rb_insert_augmented()
is called, which is missing.
So we add the augment-code to drbd_insert_interval() when it travels the
tree up to down before rb_insert_augmented(). See the example in
include/linux/interval_tree_generic.h or Documentation/rbtree.txt.
drbd_insert_interval() may cancel the insertion when traveling, in this
case, the just added augment-code does nothing before cancel since the
@this node is already in the subtrees in this case.
CC: Michel Lespinasse <walken@google.com>
CC: stable@kernel.org # v3.10+
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Declare the SCKC (Slow Clock Configuration) block and its clks.
Make use of the clk32k clk instead of slow_osc where appropriate.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Otherwise the clock for can0 will never get enabled.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: stable@vger.kernel.org # v3.14
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9g20 support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9rl support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This reverts commit b96de000bc.
This commit is triggering failures to mount by subvolume id in some
configurations. The main problem is how many different ways this
scanning function is used, both for scanning while mounted and
unmounted. A proper cleanup is too big for late rcs.
For now, just revert the commit and we'll put a better fix into a later
merge window.
Signed-off-by: Chris Mason <clm@fb.com>
This reverts commit be0a8887bb.
The original commit f2267089ea
(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) ended up being reverted because it caused
more issues then fixed. We will also revert this counter part
commit so we start clean to properly add that idea back.
Cc: Li Jun <b47624@freescale.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
The tracepoint of extent map doesn't parse @flag correctly, we set @flag via
set_bit(), so we need to parse it on a bit bias.
Also add the missing flag, EXTENT_FLAG_FS_MAPPING.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
The following commit enhanced the merge_extent_mapping() to reduce
fragment in extent map tree, but it can't handle case which existing
lies before map_start:
51f39 btrfs: Use right extent length when inserting overlap extent map.
[BUG]
When existing extent map's start is before map_start,
the em->len will be minus, which will corrupt the extent map and fail to
insert the new extent map.
This will happen when someone get a large extent map, but when it is
going to insert it into extent map tree, some one has already commit
some write and split the huge extent into small parts.
[REPRODUCER]
It is very easy to tiger using filebench with randomrw personality.
It is about 100% to reproduce when using 8G preallocated file in 60s
randonrw test.
[FIX]
This patch can now handle any existing extent position.
Since it does not directly use existing->start, now it will find the
previous and next extent around map_start.
So the old existing->start < map_start bug will never happen again.
[ENHANCE]
This patch will insert the best fitted extent map into extent map tree,
other than the oldest [map_start, map_start + sectorsize) or the
relatively newer but not perfect [map_start, existing->start).
The patch will first search existing extent that does not intersects with
the desired map range [map_start, map_start + len).
The existing extent will be either before or behind map_start, and based
on the existing extent, we can find out the previous and next extent
around map_start.
So the best fitted extent would be [prev->end, next->start).
For prev or next is not found, em->start would be prev->end and em->end
wold be next->start.
With this patch, the fragment in extent map tree should be reduced much
more than the 51f39 commit and reduce an unneeded extent map tree search.
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
This patch fixes the detection of the 'open_writers' violation for mmaped
files.
before) an 'open_writers' violation is detected if the policy contains
a rule with the criteria: func=FILE_CHECK mask=MAY_READ
after) an 'open_writers' violation is detected if the current event
matches one of the policy rules.
With the old behaviour, the 'open_writers' violation is not detected
in the following case:
policy:
measure func=FILE_MMAP mask=MAY_EXEC
steps:
1) open a shared library for writing
2) execute a binary that links that shared library
3) during the binary execution, modify the shared library and save
the change
result:
the 'open_writers' violation measurement is not present in the IMA list.
Only binaries executed are protected from writes. For libraries mapped
in memory there is the flag MAP_DENYWRITE for this purpose, but according
to the output of 'man mmap', the mmap flag is ignored.
Since ima_rdwr_violation_check() is now called by process_measurement()
the information about if the inode must be measured is already provided
by ima_get_action(). Thus the unnecessary function ima_must_measure()
has been removed.
Changes in v3 (Dmitry Kasatkin):
- Violation for MMAP_CHECK function are verified since this patch
- Changed patch description a bit
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
This patch fixes a race condition between two functions that try to access
the same inode. Since the i_mutex lock is held and released separately
in the two functions, there may be the possibility that a violation is
not correctly detected.
Suppose there are two processes, A (reader) and B (writer), if the
following sequence happens:
A: ima_rdwr_violation_check()
B: ima_rdwr_violation_check()
B: process_measurement()
B: starts writing the inode
A: process_measurement()
the ToMToU violation (a reader may be accessing a content different from
that measured, due to a concurrent modification by a writer) will not be
detected. To avoid this issue, the violation check and the measurement
must be done atomically.
This patch fixes the problem by moving the violation check inside
process_measurement() when the i_mutex lock is held. Differently from
the old code, the violation check is executed also for the MMAP_CHECK
hook (other than for FILE_CHECK). This allows to detect ToMToU violations
that are possible because shared libraries can be opened for writing
while they are in use (according to the output of 'man mmap', the mmap()
flag MAP_DENYWRITE is ignored).
Changes in v5 (Roberto Sassu):
* get iint if action is not zero
* exit process_measurement() after the violation check if action is zero
* reverse order process_measurement() exit cleanup (Mimi)
Changes in v4 (Dmitry Kasatkin):
* iint allocation is done before calling ima_rdrw_violation_check()
(Suggested-by Mimi)
* do not check for violations if the policy does not contain 'measure'
rules (done by Roberto Sassu)
Changes in v3 (Dmitry Kasatkin):
* no violation checking for MMAP_CHECK function in this patch
* remove use of filename from violation
* removes checking if ima is enabled from ima_rdrw_violation_check
* slight style change
Suggested-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
We set the DMA configuration on USARTs in the SoC DT in (ARM: at91: sama5d3:
add usart dma configurations). As the audio must work with DMA channels, we
reserve some dma channels for audio, or else audio won't work.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: move to the sama5d3xmb.dtsi to cover all board variants]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable interrupts from all 32 bundles.
Signed-off-by: Conor McLoughlin <conor.mcloughlin@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't abort clock initialization if we cannot match an entry in
tegra_clk_init_table to a valid entry in the clk array.
Also log a corresponding error message.
This was discovered when testing a patch that removed the EMC clock from
tegra124_clks but left a mention in tegra_clk_init_table.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
The limited color range knob is in the port registers on
g4x and vlv/chv for HDMI, and on g4x for DP. Add the relevant code
to read out the hardware state into pipe config. On vlv/chv the
DP port limited color range knob is in PIPECONF for which we
already have readout code.
Cc: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
They were not used, and we don't need them, so we shouldn't bother with
keeping values in the flags field that could be misleading.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we can't get MSI-X vectors, we disable a few features which require
MSI-X vectors. Print warnings just like we do when disabling DCB.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Again, we should not be directly using netif_printk, as we have our own
error print routines that we generate. In addition, instead of using an
early return we can just use the else block of this one line if
statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In this case, disabling DCB is not an error. We can still function, but
we just have to let the user know. In addition, since we call this
during probe before allocating our netdevice structure, we should use
e_dev_warn instead of e_warn.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our calculated v_budget doesn't matter except if we allocate MSI-X
vectors. We shouldn't need to calculate this outside of the function, so
don't. Instead, only calculate it once we attempt to acquire MSI-X
vectors. This helps collocate all of the MSI-X vector code together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add these clocks to the binding header so that EMC timings that have
them as parent can refer to the clocks.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
We already have to kfree this value if we fail, and this is only part of
MSI-X mode, so we should simply allocate the value where we need it.
This is cleaner, and makes it a lot more obvious why we are freeing it
inside of ixgbe_acquire_msix_vectors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to how ixgbevf handles acquiring MSI-X vectors, we can return an
error code instead of relying on the flag being set. This makes it more
clear that we have failed to setup MSI-X mode, and also will make it
easier to consolidate MSI-X related code all into the single function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netif_printk relies on our netdevice structure to be registered
already. We may call ixgbe_acquire_msix_vectors prior to registering our
netdevice, so we should not use the netdevice specific printk.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
