Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.
The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.
This patch adds
[1] the neccessary fields for nand_onfi_params{},
[2] and adds the onfi_ext_ecc_info{} for Extended ECC information,
[3] adds onfi_ext_section{} for extended sections,
[4] and adds onfi_ext_param_page{} for the Extended Parameter Page.
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
[Brian: amended for checkpatch.pl]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1.) Why add the ECC information to the nand_chip{} ?
Each nand chip has its requirement for the ECC correctability, such as
"4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte".
This ECC info is very important to the nand controller, such as gpmi.
Take the Micron MT29F64G08CBABA for example, its geometry is
8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB.
If we do not provide the ECC info to the gpmi nand driver, it has to
calculate the ECC correctability itself. The gpmi driver will gets the 56bit
ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility.
The gpmi will quits in this case. But in actually, the gpmi can supports
this nand chip if it can get the right ECC info.
2.) about the new fields.
The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds.
The two fields should be set from the nand chip's datasheets.
For example:
"4bit ECC for each 512Byte" could be:
@ecc_strength_ds = 4, @ecc_step_ds = 512.
"40bit ECC for each 1024Byte" could be:
@ecc_strength_ds = 40, @ecc_step_ds = 1024.
3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}?
The @strength and @size in nand_ecc_ctrl{} is used by the nand controller
driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a build error that occurs when CONFIG_PM is enabled
and CONFIG_PM_SLEEP isn't:
>> drivers/usb/host/ohci-pci.c:294:10: error: 'usb_hcd_pci_pm_ops' undeclared here (not in a function)
.pm = &usb_hcd_pci_pm_ops
Since the usb_hcd_pci_pm_ops structure is defined and used when
CONFIG_PM is enabled, its declaration should not be protected by
CONFIG_PM_SLEEP.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NAND_BBT_SCANEMPTY is a strange, badly-supported option with omap as its
single remaining user.
NAND_BBT_SCANEMPTY was likely used by accident in omap2[1]. And anyway,
omap2 doesn't scan the chip for bad blocks (courtesy of
NAND_SKIP_BBTSCAN), and so its use of this option is irrelevant.
This patch drops the NAND_BBT_SCANEMPTY option.
[1] http://lists.infradead.org/pipermail/linux-mtd/2012-July/042902.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_base.c shouldn't have to know the implementation details of
nand_bbt's in-memory BBT. Specifically, nand_base shouldn't perform the
bit masking and shifting to isolate a BBT entry.
Instead, just move some of the BBT code into a new nand_markbad_bbt()
interface. This interface allows external users (i.e., nand_base) to
mark a single block as bad in the BBT. Then nand_bbt will take care of
modifying the in-memory BBT and updating the flash-based BBT (if
applicable).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current system requires everyone to set up notifiers, manage directory
locking, etc.
What we really want to do is have the rpc_client create its directory,
and then create all the entries.
This patch will allow the RPCSEC_GSS and NFS code to register all the
objects that they want to have appear in the directory, and then have
the sunrpc code call them back to actually create/destroy their pipefs
dentries when the rpc_client creates/destroys the parent.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The clnt->cl_principal is being used exclusively to store the service
target name for RPCSEC_GSS/krb5 callbacks. Replace it with something that
is stored only in the RPCSEC_GSS-specific code.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HDMI_IDENTIFIER was felt too generic, rename it to what it is, the IEEE
OUI corresponding to HDMI Licensing, LLC.
http://standards.ieee.org/develop/regauth/oui/oui.txt
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
We just got rid of the version of hdmi_vendor_infoframe that had a byte
array for anyone to poke at. It's now time to shuffle around the naming
of hdmi_hdmi_infoframe to make hdmi_vendor_infoframe become the HDMI
vendor specific structure.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
With this last bit, hdmi_infoframe_pack() is now able to pack any
infoframe we support.
At the same time, because it's impractical to make two commits out of
this, we get rid of the version that encourages the open coding of the
vendor infoframe packing. We can do so because the only user of this API
has been ported in:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Aug 12 18:08:37 2013 +0100
gpu: host1x: Port the HDMI vendor infoframe code the common helpers
v2: Change oui to be an unsigned int (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
We'll need the HDMI OUI for the HDMI vendor infoframe data, so let's
move the DRM one to hdmi.h, might as well use the hdmi header to store
some hdmi defines.
(Note that, in fact, infoframes are part of the CEA-861 standard, and
only the HDMI vendor specific infoframe is special to HDMI, but
details..)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Provide the same programming model than the other infoframe types.
The generic _pack() function can't handle those yet as we need to move
the vendor OUI in the generic hdmi_vendor_infoframe structure to know
which kind of vendor infoframe we are dealing with.
v2: Fix the value of Side-by-side (half), hmdi typo, pack 3D_Ext_Data
(Ville Syrjälä)
v3: Future proof the sending of 3D_Ext_Data (Ville Syrjälä), Fix
multi-lines comment style (Thierry Reding)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Just like:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Aug 12 11:53:24 2013 +0100
video/hdmi: Don't let the user of this API create invalid infoframes
But this time for the horizontal/vertical bar data present bits.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
To set the active aspect ratio value in the AVI infoframe today, you not
only have to set the active_aspect field, but also the active_info_valid
bit. Out of the 1 user of this API, we had 100% misuse, forgetting the
_valid bit. This was fixed in:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Aug 6 20:32:17 2013 +0100
drm: Don't generate invalid AVI infoframes for CEA modes
We can do better and derive the _valid bit from the user wanting to set
the active aspect ratio.
v2: Fix multi-lines comment style (Thierry Reding)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
While poking at something using the for-3.12/* trees, I hit the
following compile error:
drivers/built-in.o: In function `tegra_pcie_map_irq':
/builddir/build/BUILD/kernel-3.10.fc20/linux-3.11.0-0.rc6.git4.1.fc20.armv7hl/drivers/pci/host/pci-tegra.c:640:
undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
drivers/built-in.o: In function `tegra_msi_map':
/builddir/build/BUILD/kernel-3.10.fc20/linux-3.11.0-0.rc6.git4.1.fc20.armv7hl/drivers/pci/host/pci-tegra.c:1227:
undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
make: *** [vmlinux] Error 1
Since our .config had CONFIG_CPU_IDLE off. We should probably provide
an empty function to handle this to avoid cluttering up pci-tegra.c
with conditionals.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
[swarren, removed unnecessary return statement]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
For at91 boards, there are different IPs for adc. Different IPs has different
STARTUP & PRESCAL mask in ADC_MR.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is identical to of_parse_phandle_with_args(), except that the
number of argument cells is fixed, rather than being parsed out of the
node referenced by each phandle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Vx7M
-----END PGP SIGNATURE-----
Merge tag 'mmp-irq' of git://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into late/all
From Haojian Zhuang:
Move irq driver out of mach-mmp to support multiplatform
* tag 'mmp-irq' of git://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
The new macro netdev_for_each_upper_dev_rcu(dev, upper, iter) iterates
through the dev->upper_dev_list starting from the first element, using
the netdev_upper_get_next_dev_rcu(dev, &iter).
Must be called under RCU read lock.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds lower_dev_list list_head to net_device, which is the same
as upper_dev_list, only for lower devices, and begins to use it in the same
way as the upper list.
It also changes the way the whole adjacent device lists work - now they
contain *all* of upper/lower devices, not only the first level. The first
level devices are distinguished by the bool neighbour field in
netdev_adjacent, also added by this patch.
There are cases when a device can be added several times to the adjacent
list, the simplest would be:
/---- eth0.10 ---\
eth0- --- bond0
\---- eth0.20 ---/
where both bond0 and eth0 'see' each other in the adjacent lists two times.
To avoid duplication of netdev_adjacent structures ref_nr is being kept as
the number of times the device was added to the list.
The 'full view' is achieved by adding, on link creation, all of the
upper_dev's upper_dev_list devices as upper devices to all of the
lower_dev's lower_dev_list devices (and to the lower_dev itself), and vice
versa. On unlink they are removed using the same logic.
I've tested it with thousands vlans/bonds/bridges, everything works ok and
no observable lags even on a huge number of interfaces.
Memory footprint for 128 devices interconnected with each other via both
upper and lower (which is impossible, but for the comparison) lists would be:
128*128*2*sizeof(netdev_adjacent) = 1.5MB
but in the real world we usualy have at most several devices with slaves
and a lot of vlans, so the footprint will be much lower.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
device_hotplug_lock is held around the acpi_bus_trim() call in
acpi_scan_hot_remove() which generally removes devices (it removes
ACPI device objects at least, but it may also remove "physical"
device objects through .detach() callbacks of ACPI scan handlers).
Thus, potentially, device sysfs attributes are removed under that
lock and to remove those attributes it is necessary to hold the
s_active references of their directory entries for writing.
On the other hand, the execution of a .show() or .store() callback
from a sysfs attribute is carried out with that attribute's s_active
reference held for reading. Consequently, if any device sysfs
attribute that may be removed from within acpi_scan_hot_remove()
through acpi_bus_trim() has a .store() or .show() callback which
acquires device_hotplug_lock, the execution of that callback may
deadlock with the removal of the attribute. [Unfortunately, the
"online" device attribute of CPUs and memory blocks is one of them.]
To avoid such deadlocks, make all of the sysfs attribute callbacks
that need to lock device hotplug, for example store_online(), use
a special function, lock_device_hotplug_sysfs(), to lock device
hotplug and return the result of that function immediately if it is
not zero. This will cause the s_active reference of the directory
entry in question to be released and the syscall to be restarted
if device_hotplug_lock cannot be acquired.
[show_online() actually doesn't need to lock device hotplug, but
it is useful to serialize it with respect to device_offline() and
device_online() for the same device (in case user space attempts to
run them concurrently) which can be done with the help of
device_lock().]
Reported-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reported-and-tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
This patch moves the pca953x.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch implements RFC6980: Drop fragmented ndisc packets by
default. If a fragmented ndisc packet is received the user is informed
that it is possible to disable the check.
Cc: Fernando Gont <fernando@gont.com.ar>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
From Christian Daudt, SoC changes for Broadcom.
* 'armsoc/for-3.12/soc' of git://github.com/broadcom/bcm11351: (673 commits)
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
+ Linux 3.11-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- introduce support for MSI on PCI
- fix s390 build breakage when !HAVE_GENERIC_HARDIRQS
NOTE: This branch is a dependency for changes going though arm-soc from both
Thomas Petazzoni and Thierry Reding.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSC9XJAAoJEAi3KVZQDZAebeUIAJCZtJ9cth52Hhbw5hZCpuwy
9F7C8FVrOA66xw9ryFBhcKMFZN9G1YAciaBmIXSXL6Zxj/p4ZTDdzfyiWHM67Hvj
Bq+fD6GgtARB3zmi10dWhIqKOEXC7wmG68u3k4xengLxB8d4VlGHRXnrAzz+XAyo
y6mtCgzfALXkjNTTHmZW3ecuxiyXo2T7IP2e5feK8qgmFRvBR0vWdv59Kk/qurSd
E/9MjdtMJjLIXy/+h0vbAQbujA7g3e+P0JaNsxNDPxDIrWG3a61gzOqlbkgNZKIu
HCaSxg37d2cPG9PVTdoWq88nZ1+aVBfWQdaL59jmui2lZ6LNZtrnwnsSg6SOzEA=
=/x8J
-----END PGP SIGNATURE-----
Merge tag 'msi-3.12' of git://git.infradead.org/linux-mvebu into next/drivers
From Jason Cooper:
mvebu msi pci changes for v3.12
- introduce support for MSI on PCI
- fix s390 build breakage when !HAVE_GENERIC_HARDIRQS
NOTE: This branch is a dependency for changes going though arm-soc from both
Thomas Petazzoni and Thierry Reding.
* tag 'msi-3.12' of git://git.infradead.org/linux-mvebu:
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
Signed-off-by: Olof Johansson <olof@lixom.net>
The "Report ID" field of a HID report is used to build indexes of
reports. The kernel's index of these is limited to 256 entries, so any
malicious device that sets a Report ID greater than 255 will trigger
memory corruption on the host:
[ 1347.156239] BUG: unable to handle kernel paging request at ffff88094958a878
[ 1347.156261] IP: [<ffffffff813e4da0>] hid_register_report+0x2a/0x8b
CVE-2013-2888
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSGqS5AAoJEHm+PkMAQRiGFxEH/3VrqF6WAkcviNiW/0DCdO8k
v6Wi7Sp5LxVkwzmOCHCV1tTHwLRlH3cB9YmJlGQ0kHCREaAuEQAB0xJXIW7dnyYj
Qq7KoRZEMe3wizmjEsj8qsrhfMLzHjBw67hBz2znwW/4P7YdgzwD7KRiEat+yRC9
ON3nNL2zIqpfk92RXvVrSVl4KMEM+WNbOfiffgBiEP24Ja1MJMFH1d4i6hNOaB0x
9Pb3Lw8let92x+8Ao5jnjKdKMgVsoZWbN/TgQR8zZOHM38AGGiDgk18vMz+L+hpS
jqfjckxj1m30jGq0qZ9ZbMZx3IGif4KccVr30MqNHJpwi6Q24qXvT3YfA3HkstM=
=nAab
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc7' into devel
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
Don't allow mounting sysfs unless the caller has CAP_SYS_ADMIN rights
over the net namespace. The principle here is if you create or have
capabilities over it you can mount it, otherwise you get to live with
what other people have mounted.
Instead of testing this with a straight forward ns_capable call,
perform this check the long and torturous way with kobject helpers,
this keeps direct knowledge of namespaces out of sysfs, and preserves
the existing sysfs abstractions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* pci/misc:
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
This just replaces the dentry count/lock combination with the lockref
structure that contains both a count and a spinlock, and does the
mechanical conversion to use the lockref infrastructure.
There are no semantic changes here, it's purely syntactic. The
reference lockref implementation uses the spinlock exactly the same way
that the old dcache code did, and the bulk of this patch is just
expanding the internal "d_count" use in the dcache code to use
"d_lockref.count" instead.
This is purely preparation for the real change to make the reference
count updates be lockless during the 3.12 merge window.
[ As with the previous commit, this is a rewritten version of a concept
originally from Waiman, so credit goes to him, blame for any errors
goes to me.
Waiman's patch had some semantic differences for taking advantage of
the lockless update in dget_parent(), while this patch is
intentionally a pure search-and-replace change with no semantic
changes. - Linus ]
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces a new "lockref" structure that supports the concept of
lockless updates of reference counts that still honor an attached
spinlock.
NOTE! This reference implementation is not the optimized lockless
version, rather it is the fallback implementation using standard
spinlocks. The actual optimized versions will be merged into 3.12, but
I wanted to get the infrastructure in place and document the new
interfaces.
[ Also note that this particular commit is drastically cut-down minimal
version of the original patch by Waiman. In order to properly credit
the original author I'm marking Waiman as the author here, but in the
end this patch bears little resemblance to the patch by Waiman. So
blame any errors on me editing things down to the point where I can
introduce the infrastructure before the merge window for 3.12 actually
opens. - Linus ]
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/of_net.h:16: warning: type qualifiers ignored on function return type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
From Lorenzo Pieralisi:
This patch series contains:
- GIC driver update to add a method to disable the GIC CPU IF
- TC2 MCPM update to add GIC CPU disabling to suspend method
- TC2 CPU idle big.LITTLE driver
* cpuidle/biglittle:
cpuidle: big.LITTLE: vexpress-TC2 CPU idle driver
ARM: vexpress: tc2: disable GIC CPU IF in tc2_pm_suspend
drivers: irq-chip: irq-gic: introduce gic_cpu_if_down()
ARM: vexpress/TC2: implement PM suspend method
ARM: vexpress/TC2: basic PM support
ARM: vexpress: Add SCC to V2P-CA15_A7's device tree
ARM: vexpress/TC2: add Serial Power Controller (SPC) support
ARM: vexpress/dcscb: fix cache disabling sequences
Signed-off-by: Olof Johansson <olof@lixom.net>
When processors are about to hit low power states, the assertion of
standbywfi signal, triggered by the wfi instruction, is essential to
entering low power modes. If an IRQ is pending on the processor at the
time wfi is issued, the wfi instruction completes and the processor
restarts execution without asserting the standbywfi signal. Depending
on the platform power controller HW this behaviour can be acceptable or
not; if this behaviour must be prevented software should be provided
with a way to disable the routing of interrupts to the core IRQ pins.
On systems where raw GIC distributor interrupts are connected to the power
controller as wake-up events (hence the power controller still senses
IRQs and can wake up cores upon IRQ pending), the GIC CPU interface can
be disabled on power down, so that the GIC CPU IF output is gated and wfi
cannot complete, thereby preventing the standbywfi issue.
This patch adds a simple function to the GIC driver that allows to
disable the GIC CPU IF from power down procedures.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[rewrote commit log]
Signed-off-by: Olof Johansson <olof@lixom.net>
When DEBUG is defined, dev_dbg_ratelimited uses dynamic debug data
structures even when CONFIG_DYNAMIC_DEBUG is not defined.
It leads to build break.
For example, when I try to use dev_dbg_ratelimited in USB code and
CONFIG_USB_DEBUG is enabled, but CONFIG_DYNAMIC_DEBUG is not, I get:
CC [M] drivers/usb/host/xhci-ring.o
drivers/usb/host/xhci-ring.c: In function ‘xhci_queue_intr_tx’:
drivers/usb/host/xhci-ring.c:3059:3: error: implicit declaration of function ‘DEFINE_DYNAMIC_DEBUG_METADATA’ [-Werror=implicit-function-declaration]
drivers/usb/host/xhci-ring.c:3059:3: error: ‘descriptor’ undeclared (first use in this function)
drivers/usb/host/xhci-ring.c:3059:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/usb/host/xhci-ring.c:3059:3: error: implicit declaration of function ‘__dynamic_pr_debug’ [-Werror=implicit-function-declaration]
drivers/usb/host/xhci-ring.c: In function ‘xhci_queue_isoc_tx_prepare’:
drivers/usb/host/xhci-ring.c:3847:3: error: ‘descriptor’ undeclared (first use in this function)
cc1: some warnings being treated as errors
make[2]: *** [drivers/usb/host/xhci-ring.o] Error 1
make[1]: *** [drivers/usb/host] Error 2
make: *** [drivers/usb/] Error 2
This patch separates definition for CONFIG_DYNAMIC_DEBUG and DEBUG cases.
[Note, Sarah moved the comment above the macro to avoid checkpatch
warnings.]
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement ib_create_flow() and ib_destroy_flow().
Translate the verbs structures provided by the user to HW structures
and call the MLX4_QP_FLOW_STEERING_ATTACH/DETACH firmware commands.
On the ATTACH command completion, the firmware provides a 64-bit
registration ID, which is placed into struct mlx4_ib_flow that wraps
the instance of struct ib_flow which is retuned to caller. Later,
this reg ID is used for detaching that flow from the firmware.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When I included the "empty" function for sysfs_create_groups() when
CONFIG_SYSFS=n, I forgot to return a value for it, so things blew up the
build. This patch fixes that, stupid me.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
