The purpose of this patch is to guarantee that ab8500-debug will
record the regulator registers before they are modified by the
ab8500 regulator driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for HW request is added in the external regulator
driver. A flag in the board configuration can be set to
let HW control the regulator when there is no SW request.
This means that the regulator will be put in high power
mode when there is a SW request and in HW-request mode
otherwise.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI drivers should be able to carry their private data around.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei client bus will present some of the mei clients
as devices for other standard subsystems
Implement the probe, remove, match, device addtion routines, along with
the sysfs and uevent ones. mei_cl_device_id is also added to
mod_devicetable.h
A mei-cleint-bus.txt document describing the rationale and the API usage
is also added while ABI/testing/sysfs-bus-mei describeis the modalias ABI.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1869305009 ("mm: introduce VM_POPULATE flag to
better deal with racy userspace programs").
VM_POPULATE only has any effect when userspace plays racy games with
vmas by trying to unmap and remap memory regions that mmap or mlock are
operating on.
Also, the only effect of VM_POPULATE when userspace plays such games is
that it avoids populating new memory regions that get remapped into the
address range that was being operated on by the original mmap or mlock
calls.
Let's remove VM_POPULATE as there isn't any strong argument to mandate a
new vm_flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some USB fixes to resolve issues reported recently, as well as a new
device id for the ftdi_sio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFUaA0ACgkQMUfUDdst+yk0AACfe9iitBiGERSO4NsyIvypoJ1q
vOgAoKek8fiPmTKrZl18n79oX28qU9x2
=Oee3
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes to resolve issues reported recently, as well
as a new device id for the ftdi_sio driver."
* tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
usb: Fix compile error by selecting USB_OTG_UTILS
USB: serial: fix hang when opening port
USB: EHCI: fix bug in iTD/siTD DMA pool allocation
xhci: Don't warn on empty ring for suspended devices.
usb: xhci: Fix TRB transfer length macro used for Event TRB.
usb/acpi: binding xhci root hub usb port with ACPI
usb: add find_raw_port_number callback to struct hc_driver()
usb: xhci: fix build warning
Here are some small char/misc driver fixes that resolve issues recently
reported against the 3.9-rc kernels. All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFUdOAACgkQMUfUDdst+ykb9QCeKb0WfCxqwPFZDCAbIiyX9AyA
1OMAoJU7WJo1/wpfyyTLr6RuN8E0X0p/
=1+Ic
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes that resolve issues
recently reported against the 3.9-rc kernels. All have been in
linux-next for a while."
* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Fix process-to-process DRGAMs.
mei: ME hardware reset needs to be synchronized
mei: add mei_stop function to stop mei device
extcon: max77693: Initialize register of MUIC device to bring up it without platform data
extcon: max77693: Fix bug of wrong pointer when platform data is not used
extcon: max8997: Check the pointer of platform data to protect null pointer error
Pull userns fixes from Eric W Biederman:
"The bulk of the changes are fixing the worst consequences of the user
namespace design oversight in not considering what happens when one
namespace starts off as a clone of another namespace, as happens with
the mount namespace.
The rest of the changes are just plain bug fixes.
Many thanks to Andy Lutomirski for pointing out many of these issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Restrict when proc and sysfs can be mounted
ipc: Restrict mounting the mqueue filesystem
vfs: Carefully propogate mounts across user namespaces
vfs: Add a mount flag to lock read only bind mounts
userns: Don't allow creation if the user is chrooted
yama: Better permission check for ptraceme
pid: Handle the exit of a multi-threaded init.
scm: Require CAP_SYS_ADMIN over the current pidns to spoof pids.
The Marvell EBU SoCs have a configurable physical address space
layout: the physical ranges of memory used to address PCI(e)
interfaces, NOR flashes, SRAM and various other types of memory are
configurable by software, through a mechanism of so-called 'address
decoding windows'.
This new driver mvebu-mbus consolidates the existing code to address
the configuration of these memory ranges, which is spread into
mach-mvebu, mach-orion5x, mach-mv78xx0, mach-dove and mach-kirkwood.
Following patches convert each Marvell EBU SoC family to use this
driver, therefore removing the old code that was configuring the
address decoding windows.
It is worth mentioning that the MVEBU_MBUS Kconfig option is
intentionally added as a blind option. The new driver implements and
exports the mv_mbus_dram_info() function, which is used by various
Marvell drivers throughout the tree to get access to window
configuration parameters that they require. This function is also
implemented in arch/arm/plat-orion/addr-map.c, which ultimately gets
removed at the end of this patch series. So, in order to preserve
bisectability, we want to ensure that *either* this new driver, *or*
the legacy code in plat-orion/addr-map.c gets compiled in.
By making MVEBU_MBUS a blind option, we are sure that only a platform
that does 'select MVEBU_MBUS' will get this new driver compiled
in. Therefore, throughout the next patches that convert the Marvell
sub-architectures one after the other to this new driver, we add the
'select MVEBU_MBUS' and also ensure to remove plat-orion/addr-map.c
from the build for this specific sub-architecture. This ensures that
bisectability is preserved.
Ealier versions of this driver had a DT binding, but since those were
not yet agreed upon, they were removed. The driver still uses
of_device_id to find the SoC specific details according to the string
passed to mvebu_mbus_init(). The plan is to re-introduce a proper DT
binding as a followup set of patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Translates SCSI commands in SG_IO ioctl to NVMe commands.
Uses the scsi-nvme translation spec from nvmexpress.org as reference.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was unnoticed for some time that assigning to current->policy is
no longer sufficient to set a real time priority for a kernel thread.
Reported-by: Charlie Suffin <Charlie.Suffin@stratus.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The issue was that if the connection broke while we did the
gracefull state change to C_DISCONNECTING (C_TEARDOWN), then
we returned a success code from the state engine. (SS_CW_NO_NEED)
The result of that is that we missed to call the fence-peer
script in such a case.
Fixed that by introducing a new error code (SS_OUTDATE_WO_CONN).
This one should never reach back into user space.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
And some manual common subexpression elimination which may help the
compiler produce smaller code.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This ensures that a function pointer passed into CLOCKSOURCE_OF_DECLARE
takes the same arguments that we use for calling that function later.
Also fix the extraneous semicolon at end of the CLOCKSOURCE_OF_DECLARE
definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tokenring support was deleted in v3.5. One last holdout of the macro
CONFIG_TR escaped that fate. Until now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 40893fd(net: switch to use skb_probe_transport_header())
involes a new error accidently. When NET_SKBUFF_DATA_USES_OFFSE is
not enabled, below compile error happens:
CC net/packet/af_packet.o
net/packet/af_packet.c: In function ‘packet_sendmsg_spkt’:
net/packet/af_packet.c:1516:2: error: implicit declaration of function ‘skb_probe_transport_header’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [net/packet/af_packet.o] Error 1
make[1]: *** [net/packet] Error 2
make: *** [net] Error 2
As it seems skb_probe_transport_header() is not related to
NET_SKBUFF_DATA_USES_OFFSE, we should move the definition of
skb_probe_transport_header() out of scope of
NET_SKBUFF_DATA_USES_OFFSE macro.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean out initialisation that is handled by SoC. Regulator
settings for Vpll (partly), Vsmps1, Vsmps2, Vsmps3 (partly),
Vrf1, Varm, Vape, Vbb, Vmod are cleaned out. They should not
be touched by the kernel.
We also update many of the initialisation values to be more
in-line with the current development efforts of ST-Ericsson
internal engineers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some more chip IDs to bcma_pmu_get_alp_clock()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, we need probe and set the transport header for packets (e.g from
untrusted source). This patch introduces a new helper
skb_probe_transport_header() which tries to probe and set the l4 header through
skb_flow_dissect(), if not just set the transport header to the hint passed by
caller.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i915 driver uses sg lists for memory without backing 'struct page'
pages, similarly to other IO memory regions, setting only the DMA
address for these. It does this, so that it can program the HW MMU
tables in a uniform way both for sg lists with and without backing pages.
Without a valid page pointer we can't call nth_page to get the current
page in __sg_page_iter_next, so add a helper that relevant users can
call separately. Also add a helper to get the DMA address of the current
page (idea from Daniel).
Convert all places in i915, to use the new API.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only allow unprivileged mounts of proc and sysfs if they are already
mounted when the user namespace is created.
proc and sysfs are interesting because they have content that is
per namespace, and so fresh mounts are needed when new namespaces
are created while at the same time proc and sysfs have content that
is shared between every instance.
Respect the policy of who may see the shared content of proc and sysfs
by only allowing new mounts if there was an existing mount at the time
the user namespace was created.
In practice there are only two interesting cases: proc and sysfs are
mounted at their usual places, proc and sysfs are not mounted at all
(some form of mount namespace jail).
Cc: stable@vger.kernel.org
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When a read-only bind mount is copied from mount namespace in a higher
privileged user namespace to a mount namespace in a lesser privileged
user namespace, it should not be possible to remove the the read-only
restriction.
Add a MNT_LOCK_READONLY mount flag to indicate that a mount must
remain read-only.
CC: stable@vger.kernel.org
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Guarantee that the policy of which files may be access that is
established by setting the root directory will not be violated
by user namespaces by verifying that the root directory points
to the root of the mount namespace at the time of user namespace
creation.
Changing the root is a privileged operation, and as a matter of policy
it serves to limit unprivileged processes to files below the current
root directory.
For reasons of simplicity and comprehensibility the privilege to
change the root directory is gated solely on the CAP_SYS_CHROOT
capability in the user namespace. Therefore when creating a user
namespace we must ensure that the policy of which files may be access
can not be violated by changing the root directory.
Anyone who runs a processes in a chroot and would like to use user
namespace can setup the same view of filesystems with a mount
namespace instead. With this result that this is not a practical
limitation for using user namespaces.
Cc: stable@vger.kernel.org
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Mainly useful internally but exported since this is a public API that's
being checked for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to register an input device containing no events.
This allows drivers using the quirk MULTI_INPUT to register one input
per report effectively used.
For backward compatibility, we need to add a quirk to request
this behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SCSI emulation has the ability to send format commands, so we need
to add the definition of the command. Also add a missing error code.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
nvme-scsi.c uses several data structures and definitions that were
previously private to nvme-core.c. Move the definitions to nvme.h,
protected by __KERNEL__.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
It turns out that some UEFI systems provide apparently an apparently valid
PCI ROM BAR that turns out to contain garbage, so the attempt in 547b52463
to prefer the ROM from the BAR actually breaks a different set of machines.
As Linus pointed out, the graphics drivers are probably in the best
position to make this judgement, so this basically reverts 547b52463 and
f9a37be0f and adds a new helper function. Followup patches will add support
to nouveau and radeon for probing this ROM source if they can't find a ROM
from some other source.
[bhelgaas: added reporter and bugzilla pointers, s/f4eb5ff05/547b52463]
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=927451
Reference: http://lkml.kernel.org/r/kg69ef$vdb$1@ger.gmane.org
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Chris Murphy <bugzilla@colorremedies.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking fixes from David Miller:
1) Always increment IPV4 ID field in encapsulated GSO packets, even
when DF is set. Regression fix from Pravin B Shelar.
2) Fix per-net subsystem initialization in netfilter conntrack,
otherwise we may access dynamically allocated memory before it is
actually allocated. From Gao Feng.
3) Fix DMA buffer lengths in iwl3945 driver, from Stanislaw Gruszka.
4) Fix race between submission of sync vs async commands in mwifiex
driver, from Amitkumar Karwar.
5) Add missing cancel of command timer in mwifiex driver, from Bing
Zhao.
6) Missing SKB free in rtlwifi USB driver, from Jussi Kivilinna.
7) Thermal layer tries to use a genetlink multicast string that is
longer than the 16 character limit. Fix it and add a BUG check to
prevent this kind of thing from happening in the future.
From Masatake YAMATO.
8) Fix many bugs in the handling of the teardown of L2TP connections,
UDP encapsulation instances, and sockets. From Tom Parkin.
9) Missing socket release in IRDA, from Kees Cook.
10) Fix fec driver modular build, from Fabio Estevam.
11) Erroneous use of kfree() instead of free_netdev() in lantiq_etop,
from Wei Yongjun.
12) Fix bugs in handling of queue numbers and steering rules in mlx4
driver, from Moshe Lazer, Hadar Hen Zion, and Or Gerlitz.
13) Some FOO_DIAG_MAX constants were defined off by one, fix from Andrey
Vagin.
14) TCP segmentation deferral is unintentionally done too strongly,
breaking ACK clocking. Fix from Eric Dumazet.
15) net_enable_timestamp() can legitimately be invoked from software
interrupts, and in a way that is safe, so remove the WARN_ON().
Also from Eric Dumazet.
16) Fix use after free in VLANs, from Cong Wang.
17) Fix TCP slow start retransmit storms after SACK reneging, from
Yuchung Cheng.
18) Unix socket release should mark a socket dead before NULL'ing out
sock->sk, otherwise we can race. Fix from Paul Moore.
19) IPV6 addrconf code can try to free static memory, from Hong Zhiguo.
20) Fix register mis-programming, NULL pointer derefs, and wrong PHC
clock frequency in IGB driver. From Lior LevyAlex Williamson, Jiri
Benc, and Jeff Kirsher.
21) skb->ip_summed logic in pch_gbe driver is reversed, breaking packet
forwarding. Fix from Veaceslav Falico.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
ipv4: Fix ip-header identification for gso packets.
bonding: remove already created master sysfs link on failure
af_unix: dont send SCM_CREDENTIAL when dest socket is NULL
pch_gbe: fix ip_summed checksum reporting on rx
igb: fix PHC stopping on max freq
igb: make sensor info static
igb: SR-IOV init reordering
igb: Fix null pointer dereference
igb: fix i350 anti spoofing config
ixgbevf: don't release the soft entries
ipv6: fix bad free of addrconf_init_net
unix: fix a race condition in unix_release()
tcp: undo spurious timeout after SACK reneging
bnx2x: fix assignment of signed expression to unsigned variable
bridge: fix crash when set mac address of br interface
8021q: fix a potential use-after-free
net: remove a WARN_ON() in net_enable_timestamp()
tcp: preserve ACK clocking in TSO
net: fix *_DIAG_MAX constants
net/mlx4_core: Disallow releasing VF QPs which have steering rules
...
PCI defines PCI_DEVFN(), PCI_SLOT(), and PCI_FUNC() interfaces; however,
it doesn't have interfaces to return PCI bus and PCI device id. Drivers
(AMD IOMMU, and AER) implement module specific definitions for PCI_BUS()
and AMD_IOMMU driver also has a module specific interface to calculate PCI
device id from bus number and devfn.
Add PCI_BUS_NUM and PCI_DEVID interfaces to return PCI bus number and PCI
device id respectively to avoid the need for duplicate definitions in other
modules. AER driver code and AMD IOMMU driver define PCI_BUS. AMD IOMMU
driver defines an interface to calculate device id from bus number, and
devfn pair.
PCI_DEVFN(), PCI_SLOT(), and PCI_FUNC() interfaces are exported to
user-space via uapi/linux/pci.h. However, in the interest to keep the new
interfaces as kernel only and not export them to user-space unnecessarily,
added them to linux/pci.h instead.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Not all clocks are required to be decomposed into basic clock
types but at the same time want to use the functionality
provided by these basic clock types instead of duplicating.
For example, Tegra SoC has ~100 clocks which can be decomposed
into Mux -> Div -> Gate clock types making the clock count to
~300. Also, parent change operation can not be performed on gate
clock which forces to use mux clock in driver if want to change
the parent.
Instead aggregate the basic clock types functionality into one
clock and just use this clock for all operations. This clock
type re-uses the functionality of basic clock types and not
limited to basic clock types but any hardware-specific
implementation.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds discard support to block queues if the nvme device is capable of
deallocating blocks as indicated by the controller's optional command support.
A discard flagged bio request will submit an NVMe deallocate Data Set
Management command for the requested blocks.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into asoc-arizona
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
