The TI sci-clk driver can scan the DT for all clocks provided by system
firmware and does this by checking the clocks property of all nodes, so
we must add this to the dwc3 nodes so USB clocks are available.
Without this USB does not work with latest system firmware i.e.
[ 1.714662] clk: couldn't get parent clock 0 for /interconnect@100000/dwc3@4020000
Fixes: cc54a99464 ("arm64: dts: ti: k3-am6: add USB suppor")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Enabling KASLR forces the use of non-global page-table entries for kernel
mappings, as this is a decision that we have to make very early on before
mapping the kernel proper. When used in conjunction with the "kpti=off"
command-line option, it is possible to use non-global kernel mappings but
with the kpti trampoline disabled.
Since commit 09e3c22a86 ("arm64: Use a variable to store non-global
mappings decision"), arm64_kernel_unmapped_at_el0() reflects only the use of
non-global mappings and does not take into account whether the kpti
trampoline is enabled. This breaks context switching of the TPIDRRO_EL0
register for 64-bit tasks, where the clearing of the register is deferred to
the ret-to-user code, but it also breaks the ARM SPE PMU driver which
helpfully recommends passing "kpti=off" on the command line!
Report whether or not KPTI is actually enabled in
arm64_kernel_unmapped_at_el0() and check the 'arm64_use_ng_mappings' global
variable directly when determining the protection flags for kernel mappings.
Cc: Mark Brown <broonie@kernel.org>
Reported-by: Hongbo Yao <yaohongbo@huawei.com>
Tested-by: Hongbo Yao <yaohongbo@huawei.com>
Fixes: 09e3c22a86 ("arm64: Use a variable to store non-global mappings decision")
Signed-off-by: Will Deacon <will@kernel.org>
Driver should clear FIFO in PDI, or the previously stored sample data
in FIFO will generate pop noise when stream is started. The soft reset
bit will clear all the FIFO to zero and is self-cleared after that.
Signed-off-by: randerwang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enable multi-link (aka multi-master configuration). In this
configuration, updates and commands with the 'ssp_sync' tag will be
deferred and controlled by the gsync hardware signal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a good idea on paper, but it's not recommended at all when
operating in multi-master mode. It's also not recommended when doing
bank switches, since the retransmission would happen at the next SSP,
and the command protocol is stuck in the mean time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In multi-master mode, the IP will only accept SSP intervals with
integer relationships between the frame rate and the gsync frequency.
E.g for a 48kHz frame rate and 4 kHz gsync signal, the SSP interval
can only be 1, 2, 3, 4, 6, 12.
To simplify we only allow one SSP per gsync interval.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel QA reported a very rare case, possibly hardware-dependent, where
a Slave can become UNATTACHED during a clock stop sequence, which
leads to timeouts and failed suspend sequences.
This patch suppresses the handling of all Slave events while this
transition happens. The two cases that matter are:
a) alerts: if the Slave wants to signal an alert condition, it can do
so using the in-band wake, so there's almost no impact with this
patch.
b) sync loss or imp-def reset: in those cases, bringing back the Slave
to functional state requires a complete re-enumeration. It's better to
just ignore this case and restart cleanly, rather than attempt a
'clean' suspend.
Validation results show the timeouts no longer visible with this patch.
GitHub issue: https://github.com/thesofproject/linux/issues/1678
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After system resumes from S3, io timeout occurs when setting one
unused master on Comet Lake platform. In this case, the master is
reset to default state, and FIFOLEVEL is reset to default value,
but msg_count used for tracing FIFOLEVEL is still with old value,
so FIFOLEVEL will not be set if a new msg FIFO usage is equal to
the old msg_count.
This patch updates msg_count to default value of FIFOLEVEL when
resetting master.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for clock stop and restart, with two configuration
parameters:
1) when entering the ClockStop mode, Slave-initiated wakes can be
prevented.
2) When exiting the ClockStop mode, the caller can request a Bus Reset
(either if all Slaves were configured in ClockStopMode1 or the Master
IP lost context and enumeration is required)
The code handles the case where no Slaves are present by configuring
the IP to treat COMMAND_IGNORED as success.
The exit_reset part can be dealt with in the caller, along with the
required syncArm/syncGo sequence in multi-link mode.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If master is in clock stop state, driver can't modify registers
in master except the registers for clock stop setting.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need for the clock_stop_exit argument with the latest
implementation
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add uevent support to MHI bus so that the client drivers can be autoloaded
by udev when the MHI devices gets created. The client drivers are
expected to provide MODULE_DEVICE_TABLE with the MHI id_table struct so
that the alias can be exported.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for transferring data between external modem and host
processor using MHI protocol.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for processing the MHI data and control
events from the client device. The client device can report various
events such as EE events, state change events by interrupting the
host through IRQ and adding events to the event rings allocated by
the host during initialization.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI protocol supports downloading RDDM (RAM Dump) image from the
device through BHIE. This is useful to debugging as the RDDM image
can capture the firmware state.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI supports downloading the device firmware over BHI/BHIe (Boot Host
Interface) protocol. Hence, this commit adds necessary helpers, which
will be called during device power up stage.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for basic MHI PM operations such as
mhi_async_power_up, mhi_sync_power_up, and mhi_power_down. These
routines places the MHI bus into respective power domain states
and calls the state_transition APIs when necessary. The MHI
controller driver is expected to call these PM routines for
MHI powerup and powerdown.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for transitioning the MHI states as a
part of the power management operations. Helpers functions are
provided for the state transitions, which will be consumed by the
actual power management routines.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: removed dma_zalloc_coherent() and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for ringing channel and event ring doorbells
by MHI host. The MHI host can use the channel and event ring doorbells
for notifying the client device about processing transfer and event
rings which it has queued using MMIO registers.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for creating and destroying MHI devices. The
MHI devices binds to the MHI channels and are used to transfer data
between MHI host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI client drivers with the
MHI stack. MHI client drivers binds to one or more MHI devices inorder
to sends and receive the upper-layer protocol packets like IP packets,
modem control messages, and diagnostics messages over MHI bus.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI controller drivers with
the MHI stack. MHI controller drivers manages the interaction with the
MHI client devices such as the external modems and WiFi chipsets. They
are also the MHI bus master in charge of managing the physical link
between the host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: added static config for controllers and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: removed DT dependency, splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200220095854.4804-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI (Modem Host Interface) is a communication protocol used by the
host processors to control and communicate with modems over a high
speed peripheral bus or shared memory. The MHI protocol has been
designed and developed by Qualcomm Innovation Center, Inc., for use
in their modems. This commit adds the documentation for the bus and
the implementation in Linux kernel.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: converted to .rst and splitted the patch]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200227184808.GA1925@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-robot did find a type error in the min(a, b)
function used by this driver if built for x86_64 or riscv.
Althought it is very unlikely that this driver is built
for those platforms it could be used as a template
for something else and therefore should be correct.
The problem is that we implicitly cast a size_t to
unsigned int inside the implementation of the min() function.
Since size_t may differ on different compilers and
plaforms there may be warnings or not.
So let's use only size_t variables on all platforms.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: srinivas.kandagatla@linaro.org
Cc: prasannatsmkumar@gmail.com
Cc: malat@debian.org
Cc: paul@crapouillou.net
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-15-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-14-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and nvmem cells.
To fetch for example the MAC address:
dd if=/sys/devices/platform/134100d0.efuse/jz4780-efuse0/nvmem bs=1 skip=34 count=6 status=none | xxd
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-13-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
[converted to yaml]
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-12-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EPERM if reg_read is NULL in bin_attr_nvmem_read() or if
reg_write is NULL in bin_attr_nvmem_write().
This prevents NULL dereferences such as the one described in
03cd45d2e2 ("thunderbolt: Prevent crash if non-active NVMem file is
read")
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-10-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put the write-protect GPIO descriptor in nvmem_release() so that it can
be automatically released when the associated device's reference count
drops to 0.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Cc: stable <stable@vger.kernel.org>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to free the ida mapping and nvmem struct if the write-protect
GPIO lookup fails.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Visibly separate the GPIO request from the previous operation in the
code with a newline.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add nvmem_cell_read_u64() helper to ease read of an u64 value on consumer
side. This helper is useful on some sunxi platform that has 64 bits data
cells stored in no volatile memory.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there are nvmem_cell_read_u16 and nvmem_cell_read_u32.
They are very similar, let's strip out a common part.
And use nvmem_cell_read_common to simplify their implementation.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MP has 96 banks with each bank 4 words. And it has different
ctrl register layout, so add new macros for that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old drivers/char/rtc.c driver was originally the implementation
for x86 PCs but got subsequently replaced by the rtc class driver
on all architectures except alpha.
Move alpha over to the portable driver and remove the old one
for good.
The CONFIG_JS_RTC option was only ever used on SPARC32 but
has not been available for many years, this was used to build
the same rtc driver with a different module name.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: linux-alpha@vger.kernel.org
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200226224322.187960-2-alexandre.belloni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two EFI RTC drivers, the original drivers/char/efirtc.c
driver and the more modern drivers/rtc/rtc-efi.c.
Both implement the same interface, but the new one does so
in a more portable way.
Move everything over to that one and remove the old one.
Cc: linux-ia64@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200226224322.187960-1-alexandre.belloni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
