From a turbostat point of view, Cometlake is like Kabylake.
Suggested-by: Rui Zhang <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974
that has KRAIT processors the voltage/current value of each OPP
varies based on the silicon variant in use.
The required OPP related data is determined based on
the efuse value. This is similar to the existing code for
kryo cores. So adding support for krait cores here.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
commit 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
add more xdp stats to veth driver
Align veth xdp stats accounting to mellanox, intel and marvell
implementation. Introduce the following xdp counters:
- rx_xdp_tx
- rx_xdp_tx_errors
- tx_xdp_xmit
- tx_xdp_xmit_errors
- rx_xdp_redirect
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove atomic64_add from veth_xdp_xmit hotpath and rely on
xdp_xmit_err/xdp_tx_err counters
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_xmit counter in order to distinguish between XDP_TX and
ndo_xdp_xmit stats. Introduce the following ethtool counters:
- rx_xdp_tx
- rx_xdp_tx_errors
- tx_xdp_xmit
- tx_xdp_xmit_errors
- rx_xdp_redirect
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish between rx_drops and xdp_drops since the latter is already
reported in rx_packets. Report xdp_drops in ethtool statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_tx, xdp_redirect and rx_drops counters in veth_stats data
structure. Move stats accounting in veth_poll. Remove xdp_xmit variable
in veth_xdp_rcv_one/veth_xdp_rcv_skb and rely on veth_stats counters.
This is a preliminary patch to align veth xdp statistics to mlx, intel
and marvell xdp implementation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move xdp stats in veth_stats data structure. This is a preliminary patch
to align xdp statistics to mlx5, ixgbe and mvneta drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_SYSFS declaration of sysfs_group_change_owner() is different
from the !CONFIG_SYSFS version and thus causes build failurs when
!CONFIG_SYSFS is set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 303a42769c ("sysfs: add sysfs_group{s}_change_owner()")
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: phy: mscc: add support for RGMII MAC mode
This series adds support for the RGMII MAC mode for the VSC8584 PHY
family and for RGMII_ID modes (Tx and/or Rx).
I decided to drop the custom delay for now. I made some tests and it
seemed to be working quite well. If we find out we really need to lower
the delay, which I doubt, I'll send support for it.
Since v2:
- Dropped support for custom dt bindings.
- Add the 2ns delay based on the interface mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.
Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew reported:
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reported-by: Andrew Smith <andrew.smith@digi.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Offload TC action skbedit priority
Petr says:
The TC action "skbedit priority P" has the effect of assigning skbprio of P
to SKBs that it's applied on. In HW datapath of a switch, the corresponding
action is assignment of internal switch priority. Spectrum switches allow
setting of packet priority based on an ACL action, which is good match for
the skbedit priority gadget. This patchset therefore implements offloading
of this action to the Spectrum ACL engine.
After a bit of refactoring in patch #1, patch #2 extends the skbedit action
to support offloading of "priority" subcommand.
On mlxsw side, in patch #3, the QOS_ACTION flexible action is added, with
fields necessary for priority adjustment. In patch #4, "skbedit priority"
is connected to that action.
Patch #5 implements a new forwarding selftest, suitable for both SW- and
HW-datapath testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that runs traffic through a port such that skbedit priority
action acts on it during forwarding. Test that at egress, it is classified
correctly according to the new priority at a PRIO qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skbedit action "priority" is used for adjusting SKB priority. Allow
drivers to offload the action by introducing two new skbedit getters and a
new flow action, and initializing appropriately in tc_setup_flow_action().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two functions is_tcf_skbedit_mark() and is_tcf_skbedit_ptype() have a
very similar structure. A follow-up patch will add one more such function.
Instead of more cut'n'pasting, extract a helper function that checks
whether a TC action is an skbedit with the required flag. Convert the two
existing functions into thin wrappers around the helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX8/8X SCU MU is dedicated for communication between SCU and Cortex-A
cores from hardware design, and could not be reused for other purpose.
Per i.MX8/8X Reference mannual, Chapter "12.9.2.3.2 Messaging Examples",
Passing short messages: Transmit register(s) can be used to pass
short messages from one to four words in length. For example, when
a four-word message is desired, only one of the registers needs to
have its corresponding interrupt enable bit set at the receiver side;
the message’s first three words are written to the registers whose
interrupt is masked, and the fourth word is written to the other
register (which triggers an interrupt at the receiver side).
i.MX8/8X SCU firmware IPC is an implementation of passing short
messages. But current imx-mailbox driver only support one word
message, i.MX8/8X linux side firmware has to request four TX
and four RX to support IPC to SCU firmware. This is low efficent
and more interrupts triggered compared with one TX and
one RX.
To make SCU MU work,
- parse the size of msg.
- Only enable TR0/RR0 interrupt for transmit/receive message.
- For TX/RX, only support one TX channel and one RX channel
- For RX, support receive msg larger than 4 u32 words.
- Support 6 channels, TX0/RX0/RXDB[0-3], not support TXDB.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add imx_mu_generic_tx for data send and imx_mu_generic_rx for interrupt
data receive.
Pack original mu chans related code into imx_mu_init_generic
Add tx/rx/init hooks into imx_mu_dcfg
With these, it will be a bit easy to introduce i.MX8/8X SCU type
MU dedicated to communicate with SCU.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX8/8X SCU MU is dedicated for communication between SCU
and Cortex-A cores from hardware design, it could not be reused
for other purpose. To use SCU MU more effectivly, add "fsl,imx8-scu-mu"
compatile to support fast IPC.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Commit a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.
As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implement flush, client can flush the executing
command buffer or abort the still waiting for event
command buffer, so controller do not need to implement
atomic_exe feature. remove it.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
For client driver which need to reorganize the command buffer, it could
use this function to flush the send command buffer.
If the channel doesn't be started (usually in waiting for event), this
function will abort it directly.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is not any client driver using this feature now,
so remove it from binding.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Allwinner sun6i, sun8i, sun9i, and sun50i SoCs contain a hardware
message box used for communication between the ARM CPUs and the ARISC
management coprocessor. This mailbox contains 8 unidirectional
4-message FIFOs.
Add a driver for it, so it can be used with the Linux mailbox framework.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This mailbox hardware is present in Allwinner sun6i, sun8i, sun9i, and
sun50i SoCs. Add a device tree binding for it.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In this function,we don't need dev_err() message because when something
goes wrong,platform_get_irq() and devm_platform_ioremap_resource() have
print an error message itself, so we should remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_chip_specific_setup':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1378:8: warning:
variable 's' set but not used [-Wunused-but-set-variable]
It's not used since commit b6334be64d ("net/liquidio: Delete driver version assignment")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/crypto/chelsio/chcr_algo.c: In function 'chcr_device_init':
drivers/crypto/chelsio/chcr_algo.c:1440:18: warning:
variable 'adap' set but not used [-Wunused-but-set-variable]
commit 567be3a5d2 ("crypto: chelsio - Use multiple txq/rxq per tfm
to process the requests") involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the OcteonTX cpt options in crypto Kconfig and Makefile
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the cryptographic accelerator unit virtual functions on
OcteonTX 83XX SoC.
Co-developed-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the cryptographic acceleration unit (CPT) on
OcteonTX CN83XX SoC.
Co-developed-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Creats common Kconfig and Makefile for Marvell crypto drivers.
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At function exit, do not leave the expanded key in the rk struct
which got allocated on the stack.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The wake token cannot be sent without ignoring the nack for the
device address
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Combine found device and created qp into one operation instead of found
device and create qp both are independent operations. when execute
multiple tasks, the different threads may find same device at the same
time, but the number of queues is insufficient on the device. causing
one of threads fail to create a qp. Now fix this, First find device then
create qp, if result failure. the current thread will find next device.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Optimize finding hpre device process according to priority of numa
distance.
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Encapsulate hisi_qm_alloc_qps_node() to new interface to replace
find_zip_device(), which will fix the bug of creating QP failure
especially in multi-thread scenario.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Prior, passing in chunks of 2, 3, or 4, followed by any additional
chunks would result in the chacha state counter getting out of sync,
resulting in incorrect encryption/decryption, which is a pretty nasty
crypto vuln: "why do images look weird on webpages?" WireGuard users
never experienced this prior, because we have always, out of tree, used
a different crypto library, until the recent Frankenzinc addition. This
commit fixes the issue by advancing the pointers and state counter by
the actual size processed. It also fixes up a bug in the (optional,
costly) stride test that prevented it from running on arm64.
Fixes: b3aad5bad2 ("crypto: arm64/chacha - expose arm64 ChaCha routine as library function")
Reported-and-tested-by: Emil Renner Berthing <kernel@esmil.dk>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
