Add support for devices XDPE12254, XDPE12284.
All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-5-vadimp@mellanox.com
[groeck: Added missing break statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend "vrm_version" with the type for Intel IMVP9 and AMD 6.25mV VID
modes.
Add calculation for those types.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-3-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-2-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1578411640-16929-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/hwmon/w83627ehf.c: In function 'w83627ehf_check_fan_inputs':
drivers/hwmon/w83627ehf.c:1296:24: warning:
variable 'fan4min' set but not used [-Wunused-but-set-variable]
commit 62000264cfa8 ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200108034514.50130-1-yuehaibing@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1: +23.0°C
or directly from sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +23.0°C, highest = +34.0°C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for a number of manufacturer-specific registers in the
debugfs entries, as well as support to read and write the
PMBUS_ON_OFF_CONFIG register through debugfs.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-2-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now the nct677* are gone, we can clean up some flags that are
always the same now and simplify some code.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nct6775 and nct6776 are supported by the separate nct6775.c driver,
so remove the code from the w83627ehf driver.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191225023225.2785-2-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix sparse warning:
drivers/hwmon/w83627ehf.c:1202:1: warning:
symbol 'sensor_dev_attr_pwm1_target' was not declared. Should it be static?
and many more similar messages.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Link: https://lore.kernel.org/r/20191213015605.172472-1-chenzhou10@huawei.com
[groeck: Dropped all but one log message from description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a chip is write protected, we can not change any limits, and we can
not clear status flags. This may be the reason why clearing status flags
is reported to not work for some chips. Detect the condition in the pmbus
core. If the chip is write protected, set limit attributes as read-only,
and set the flag indicating that the status flag should be ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon ABI supports enable attributes since commit fb41a710f8
("hwmon: Document the sensor enable attribute"), but did not
add support for those attributes to the hwmon core. Do that now.
Since the enable attributes are logically the most important attributes,
they are added as first attribute to the attribute list. Move
hwmon_in_enable from last to first place for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the old hwmon_device_register code to
devm_hwmon_device_register_with_info.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20191124202030.45360-3-linux@treblig.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the generic PCI host binding to DT schema. The derivative Juno,
PLDA XpressRICH3-AXI, and Designware ECAM bindings all just vary in
their compatible strings. The simplest way to convert those to
schema is just add them into the common generic PCI host schema.
The HiSilicon ECAM and Cavium ThunderX PEM bindings have an additional
'reg' entry, but are otherwise the same binding as well.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Will Deacon <will@kernel.org>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the Arm Versatile PCI host binding to a DT schema.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
syzbot reported an out-of-bound access in em_nbyte. As initially
analyzed by Eric, this is because em_nbyte sets its own em->datalen
in em_nbyte_change() other than the one specified by user, but this
value gets overwritten later by its caller tcf_em_validate().
We should leave em->datalen untouched to respect their choices.
I audit all the in-tree ematch users, all of those implement
->change() set em->datalen, so we can just avoid setting it twice
in this case.
Reported-and-tested-by: syzbot+5af9a90dad568aa9f611@syzkaller.appspotmail.com
Reported-by: syzbot+2f07903a5b05e7f36410@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the reader of the document is aware that some active
installation of the libyaml development package is required and
provide two examples.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 DFSDM bindings to DT schema format
using json-schema.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
On many arm64 qcom device trees, running `make dtbs_check` yells:
timer@17c20000: #size-cells:0:0: 1 was expected
It appears that someone was trying to assert the fact that sub-nodes
describing frames would never have a size that's more than 32-bits
big. That does indeed appear to be true for all cases I could find.
Currently many arm64 qcom device tree files have a #address-cells and
about in commit bede7d2dc8 ("arm64: dts: qcom: sdm845: Increase
address and size cells for soc"). That means the only way we can
shrink them down is to use a non-empty ranges.
Since forever it has said in "writing-bindings.txt" to "DO use
non-empty 'ranges' to limit the size of child buses/devices". I guess
we should start listening to it.
I believe (but am not certain) that this also means that we should use
"ranges" to simplify the "reg" of our sub devices by specifying an
offset. Let's update the example in the bindings to make this
obvious.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This series provides updates to mlx5 driver.
1) Misc small cleanups
2) Some SW steering updates including header copy support
3) Full ethtool statistics support for E-Switch uplink representor
Some refactoring was required to share the bare-metal NIC ethtool
stats with the Uplink representor. On Top of this Vlad converts the
ethtool stats support in E-Swtich vports representors to use the mlx5e
"stats groups" infrastructure and then applied all applicable stats
to the uplink representor netdev.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl4pPoQACgkQSD+KveBX
+j43XAf/fFagUye8gFCFI2Yg0tbaDXKKvp+Z6zfA8K8URVXSksSE6dr9VraWVO8C
dtYvyv+u9IKerdi0j/uuHOHvuYAr/MwY9AV/uxltU3bxKfIbQp6puRoSU5CPVKZN
20dqN/zpbm0Tzk/k8WSpeZaPg+im5sFn7HUIoSL14AJW6KrjU6jP/pBjQMJVIcMs
Yq+QBsC9PWSfH3O4MX5qYg8IRbtXWIQplVeSU9A5Rj9+ParbMmyKOhRwq7ZcNDMM
UMA/y2z7FZ0ENQ1dajs4Yu/MiAX50sfU9M0TXwbCxim5437l26lQw3sum62Zr/Oz
rmyyVhNAX7Vm+SkHKaX85p2pOcejkQ==
=GB6e
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-01-22
This series provides updates to mlx5 driver.
1) Misc small cleanups
2) Some SW steering updates including header copy support
3) Full ethtool statistics support for E-Switch uplink representor
Some refactoring was required to share the bare-metal NIC ethtool
stats with the Uplink representor. On Top of this Vlad converts the
ethtool stats support in E-Swtich vports representors to use the mlx5e
"stats groups" infrastructure and then applied all applicable stats
to the uplink representor netdev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain says:
====================
Fixes for SONIC ethernet driver
Various SONIC driver problems have become apparent over the years,
including tx watchdog timeouts, lost packets and duplicated packets.
The problems are mostly caused by bugs in buffer handling, locking and
(re-)initialization code.
This patch series resolves these problems.
This series has been tested on National Semiconductor hardware (macsonic),
qemu-system-m68k (macsonic) and qemu-system-mips64el (jazzsonic).
The emulated dp8393x device used in QEMU also has bugs.
I have fixed the bugs that I know of in a series of patches at,
https://github.com/fthain/qemu/commits/sonic
Changed since v1:
- Minor revisions as described in commit logs.
- Deferred net-next patches.
Changed since v2:
- Minor revisions as described in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
Add PHY IDs for DP83825/6
Adding new PHY IDs for the DP83825 and DP83826 TI Ethernet PHYs to the DP83822
PHY driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY IDs for the DP83825CS, DP83825CM and the DP83825S devices to the
DP83822 driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
