Most of the packets return true for is_last_ethertype_ip, surround it
with likely compiler hint.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extend the stats group API to have an update_stats() callback which
will be used to fetch the hardware or software counters data.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Merge the per priority traffic and pfc groups into one group, because
both groups share the same update_stats() callback which will be
introduced in the upcoming patch.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-channel counter ch#_eq_rearm to monitor how many lost interrupt
recovery actions happened upon TX timeouts.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Up until this patch, on every TX timeout we would try to do channels
recovery. However, in case of a lost interrupt for an EQ, the channel
associated to it cannot be recovered if reopened as it would never get
another interrupt on sent/received traffic, and eventually ends up with
another TX timeout (Restarting the EQ is not part of channel recovery).
This patch adds a mechanism for explicitly polling EQ in case of a TX
timeout in order to recover from a lost interrupt. If this is not the
case (no pending EQEs), perform a channels full recovery as usual.
Once a lost EQE is recovered, it triggers the NAPI to run and handle all
pending completions. This will free some budget in the bql (via calling
netdev_tx_completed_queue) or by clearing pending TXWQEs and waking up
the queue. One of the above actions will move the queue to be ready for
transmit again.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When TX timeout occurs, EQ consumer index and irqn can help in debug for
understanding the SW state of EQ. Add them to the logger prints for the
relevant EQ only.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver callback for TX timeout is being called, it handles all
stopped xmit queues (not only the ones which their timeout expired).
Add usecs since last transmit to TX timeout logs per send queue in order
to monitor if the queue timeout expired.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For a given hairpin packet buffer size, different queue sizes
(values of log_hairpin_num_packets) determine how the data is broken
to strides on the RQ. Currently the chosen value is set to 64B strides.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support RSS for hairpin traffic. We create multiple hairpin RQ/SQ pairs
and RSS TTC table per hairpin instance and steer the related flows
through that table so they are spread between the pairs.
We open one pair per 50Gbs link speed, for all speeds <= 50Gbs, there
is one pair and no RSS while for 100Gbs ports two RSSed pairs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance the hairpin setup code at the core to support a set of N
(RQ,SQ) pairs. This will be later used by the caller to set RSS
spreading among the different RQs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This will allow to be able and set TC rule whose steering dest is
RSS TTC steering table.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to use RSS for hairpin, we refactor the code that deals with
setup of the TTC steering tables. This is done using an interim ttc
params object that has the flow table attributes, TIR numbers, etc.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As part of the QoS model, on xmit, the HW mandates that all packets going
through a given SQ have the same priority. To align hairpin SQs with that,
we use the priority given as part of the matching for the hairpin hash key.
This ensures that flows/packets mapped to different HW priorities will
go through different hairpin instances. If no priority is given for
matching, we treat that as an 8th priority, this is in order not to
harm cases where priority is specified.
Only the PCP priority trust model is supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The peer vhca id spans less bits vs the ifindex and can
well serve for the hairpin hash key, move to use that.
This is a pre-step to put more info into the hairpin hash
key in downstream patch while keeping it at 32 bits.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Yuchung Cheng says:
====================
tcp: do not use RTT from delayed ACKs for min-RTT
This patch set prevents TCP sender from using RTT samples from
(suspected) delayed ACKs as the minimum RTT, to avoid unbounded
over-estimation of the network path delay. This issue is common
when a connection has extended periods of one packet chit-chat
beyond the min RTT filter window. The first patch does that for TCP
general min RTT estimation. The second patch addresses specifically
the BBR congestion control's min RTT filter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A persistent connection may send tiny amount of data (e.g. health-check)
for a long period of time. BBR's windowed min RTT filter may only see
RTT samples from delayed ACKs causing BBR to grossly over-estimate
the path delay depending how much the ACK was delayed at the receiver.
This patch skips RTT samples that are likely coming from delayed ACKs. Note
that it is possible the sender never obtains a valid measure to set the
min RTT. In this case BBR will continue to set cwnd to initial window
which seems fine because the connection is thin stream.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids having TCP sender or congestion control
overestimate the min RTT by orders of magnitude. This happens when
all the samples in the windowed filter are one-packet transfer
like small request and health-check like chit-chat, which is farily
common for applications using persistent connections. This patch
tries to conservatively labels and skip RTT samples obtained from
this type of workload.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Letting tipc_poll() dereference a socket's pointer to struct tipc_group
entails a race risk, as the group item may be deleted in a concurrent
tipc_sk_join() or tipc_sk_leave() thread.
We now move the 'open' flag in struct tipc_group to struct tipc_sock,
and let the former retain only a pointer to the moved field. This will
eliminate the race risk.
Reported-by: syzbot+799dafde0286795858ac@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the switch block in l2tp_nl_cmd_session_create() that
checks pseudowire-specific parameters since just L2TP_PWTYPE_ETH and
L2TP_PWTYPE_PPP are currently supported and no actual checks are
performed. Moreover the L2TP_PWTYPE_IP/default case presents a harmless
issue in error handling (break instead of goto out_tunnel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
on T6, IPv6 filter would occupy 2 tids instead of 4.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kmalloc() failure to allocate memory generates enough information
and doesn't need to be accompanied by another driver print.
Fixes: d69a24e036 ("IB/mlx5: Move IB event processing onto a workqueue")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Now that all callers who care about RoCE addresses have been
converted to use rdma_read_gids() simplify rdma_addr_get_sgid()
to only support real GID addresses.
Callers should only use it for OPA and IB transports.
The now deleted implementation for RoCE has several bugs related to IPv6
support and incorrect/inconsistent 'GID' addresses compared to the CM
paths.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Use the newly introduced rdma_read_gids() to read the SGID and DGID for
the connection which returns GID correctly for RoCE transport as well.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
Therefore use transport agnostic rdma_read_gids() API provided by rdma_cm
module.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make use of rdma_read_gids() API to read SGID and DGID which returns
correct GIDs for RoCE and other transports.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
Therefore use transport agnostic rdma_read_gids() API provided by rdma_cm
module.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch introduces an API that allows legacy applications to query
GIDs for a rdma_cm_id which is used during connection establishment.
GIDs are stored and created differently for iWarp, IB and RoCE transports.
Therefore rdma_read_gids() returns GID for all the transports hiding
such internal details to caller.
It is usable for client side and server side connections.
In general continued use of GID based addressing outside of IB is
discouraged, so rdma_read_gids() should not be used by any new ULPs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Lorenzo Bianconi says:
====================
l2tp: set l2specific_len based on l2specific_type
Do not rely on l2specific_len value provided by userspace but set sublayer
length according to l2specific_type.
Mark L2TP_ATTR_L2SPEC_LEN attribute as not used
Changes since v2:
- drop the patch related to a fix in the switch default case in
l2tp_nl_cmd_session_create()
- use L2SPECTYPE_NONE as default case in l2tp_get_l2specific_len()
Changes since v1:
- remove l2specific_len parameter
- add sanity check on l2specific_type provided by userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove l2specific_len configuration parameter since now L2-Specific
Sublayer length is computed according to l2specific_type provided by
userspace.
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove l2specific_len dependency while building l2tpv3 header or
parsing the received frame since default L2-Specific Sublayer is
always four bytes long and we don't need to rely on a user supplied
value.
Moreover in l2tp netlink code there are no sanity checks to
enforce the relation between l2specific_len and l2specific_type,
so sending a malformed netlink message is possible to set
l2specific_type to L2TP_L2SPECTYPE_DEFAULT (or even
L2TP_L2SPECTYPE_NONE) and set l2specific_len to a value greater than
4 leaking memory on the wire and sending corrupted frames.
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sanity check on l2specific_type provided by userspace in
l2tp_nl_cmd_session_create() since just L2TP_L2SPECTYPE_DEFAULT and
L2TP_L2SPECTYPE_NONE are currently supported.
Moreover explicitly set l2specific_type to L2TP_L2SPECTYPE_DEFAULT
only if the userspace does not provide a value for it
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy says:
====================
cxgb4: reduce memory footprint for collecting firmware dump
Firmware dump can be large (upto 2 GB). In low memory conditions,
ethtool fails to allocate such large memory. So, use zlib deflate
to compress collected firmware dump.
Patch 1 updates collection logic to use compression.
Patch 2 adds zlib deflate to compress collected firmware dump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use zlib deflate to compress firmware dump. Collect and compress
as much firmware dump as possible into a 32 MB buffer.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update firmware dump collection logic to use compression when available.
Let collection logic attempt to do compression, instead of returning out
of memory early.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut reported a bug about devision by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is devision by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc4 ("net/mlx5e: Added BW check for DIM decision mechanism")
Fixes: 4c4dbb4a73 ("net/mlx5e: Move dynamic interrupt coalescing code to include/linux")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch removed all users of these two functions. Hence
also remove the functions themselves.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make sure that calling blk_mq_run_hw_queue() or
blk_mq_kick_requeue_list() triggers a queue run without delay even
if blk_mq_delay_run_hw_queue() has been called recently and if its
delay has not yet expired.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Most blk-mq functions have a name that follows the pattern blk_mq_${action}.
However, the function name blk_mq_request_direct_issue is an exception.
Hence rename this function. This patch does not change any functionality.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- The conversion of enums into their actual numbers to display
in the event format file had an off-by-one bug, that could cause
an enum not to be converted, and break user space parsing tools.
- A fix to a previous fix to bring back the context recursion checks.
The interrupt case checks for NMI, IRQ and softirq, but the softirq
returned the same number regardless if it was set or not, although
the logic would force it to be set if it were hit.
-----BEGIN PGP SIGNATURE-----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=O7m4
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.15-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more small fixes
- The conversion of enums into their actual numbers to display in the
event format file had an off-by-one bug, that could cause an enum
not to be converted, and break user space parsing tools.
- A fix to a previous fix to bring back the context recursion checks.
The interrupt case checks for NMI, IRQ and softirq, but the softirq
returned the same number regardless if it was set or not, although
the logic would force it to be set if it were hit"
* tag 'trace-v4.15-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix converting enum's from the map in trace_event_eval_update()
ring-buffer: Fix duplicate results in mapping context to bits in recursive lock
Fixes the following sparse warnings:
net/core/devlink.c:2297:25: warning:
symbol 'devlink_resource_find' was not declared. Should it be static?
net/core/devlink.c:2322:6: warning:
symbol 'devlink_resource_validate_children' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fixes from Dmitry Torokhov:
- a fix for use-after-free in Synaptics RMI4 driver
- correction to multitouch contact tracking on certain ALPS touchpads
(which got broken when we tried to fix the 2-finger scrolling)
- touchpad on Lenovo T640p is switched over to SMbus/RMI
- a few device node refcount fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - prevent UAF reported by KASAN
Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
Input: of_touchscreen - add MODULE_LICENSE
Input: 88pm860x-ts - fix child-node lookup
Input: twl6040-vibra - fix child-node lookup
Input: twl4030-vibra - fix sibling-node lookup
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:289:5: warning:
symbol 'mlxsw_sp_kvdl_part_occ' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable miistat is not used. So it is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"Two bugfixes for the I2C core: Lixing Wang fixed a refcounting problem
with DT nodes. Jeremy Compostella fixed a buffer overflow possibility
when using a 'don't use' ioctl interface directly"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core-smbus: prevent stack corruption on read I2C_BLOCK_DATA
i2c: core: decrease reference count of device node in i2c_unregister_device
Pull NVMe fixes for 4.16 from Christoph.
* 'nvme-4.16' of git://git.infradead.org/nvme:
nvme-pci: clean up SMBSZ bit definitions
nvme-pci: clean up CMB initialization
nvme-fc: correct hang in nvme_ns_remove()
nvme-fc: fix rogue admin cmds stalling teardown
nvmet: release a ns reference in nvmet_req_uninit if needed
nvme-fabrics: fix memory leak when parsing host ID option
nvme: fix comment typos in nvme_create_io_queues
nvme: host delete_work and reset_work on separate workqueues
nvme-pci: allocate device queues storage space at probe
nvme-pci: serialize pci resets
Pull libata fixlet from Tejun Heo:
"This just adds one more entry for liteon optical drives to the device
blacklist for large IOs.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: apply MAX_SEC_1024 to all LITEON EP1 series devices
Pull cgroup fix from Tejun Heo:
"cgroup.threads should be delegatable (ie. a container should be able
to write to it from inside) but was missing the flag.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: make cgroup.threads delegatable
Pull workqueue fixlet from Tejun Heo:
"One patch to add touch_nmi_watchdog() while dumping workqueue debug
messages to avoid triggering the lockup detector spuriously.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: avoid hard lockups in show_workqueue_state()
We have various small DT fixes, and one important regression fix:
The recent device tree bugfixes that were intended to address issues that
'dtc' started warning about in 4.15 fixed various USB PHY device nodes,
but it turns out that we had code that depended on those nodes being
incorrect and the probe failing with a particular error code. With the
workaround we can also deal with correct device nodes.
The DT fixes include:
- Allwinner A10 and A20 had the display pipeline set up incorrectly
(introduced in v4.15)
- The Altera PMU lacked an interrupt-parent (never worked)
- Pin muxing on the Openblocks A7 (never worked)
- Clocks might get set up wrong on Armada 7K/8K (4.15 regression)
We now have additional device tree patches to address all the remaining
warnings introduced in 4.15, but decided to queue them for 4.16 instead,
to avoid risking another regression like the USB PHY thing mentioned
above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=57ve
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"We have various small DT fixes, and one important regression fix:
The recent device tree bugfixes that were intended to address issues
that 'dtc' started warning about in 4.15 fixed various USB PHY device
nodes, but it turns out that we had code that depended on those nodes
being incorrect and the probe failing with a particular error code.
With the workaround we can also deal with correct device nodes.
The DT fixes include:
- Allwinner A10 and A20 had the display pipeline set up incorrectly
(introduced in v4.15)
- The Altera PMU lacked an interrupt-parent (never worked)
- Pin muxing on the Openblocks A7 (never worked)
- Clocks might get set up wrong on Armada 7K/8K (4.15 regression)
We now have additional device tree patches to address all the
remaining warnings introduced in 4.15, but decided to queue them for
4.16 instead, to avoid risking another regression like the USB PHY
thing mentioned above.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
phy: work around 'phys' references to usb-nop-xceiv devices
ARM: sunxi_defconfig: Enable CMA
arm64: dts: socfpga: add missing interrupt-parent
ARM: dts: sun[47]i: Fix display backend 1 output to TCON0 remote endpoint
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: da850-lcdk: Remove leading 0x and 0s from unit address
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
