Daniel Borkmann says:
====================
pull-request: bpf-next 2019-09-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Now that initial BPF backend for gcc has been merged upstream, enable
BPF kselftest suite for bpf-gcc. Also fix a BE issue with access to
bpf_sysctl.file_pos, from Ilya.
2) Follow-up fix for link-vmlinux.sh to remove bash-specific extensions
related to recent work on exposing BTF info through sysfs, from Andrii.
3) AF_XDP zero copy fixes for i40e and ixgbe driver which caused umem
headroom to be added twice, from Ciara.
4) Refactoring work to convert sock opt tests into test_progs framework
in BPF kselftests, from Stanislav.
5) Fix a general protection fault in dev_map_hash_update_elem(), from Toke.
6) Cleanup to use BPF_PROG_RUN() macro in KCM, from Sami.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
"ctx:file_pos sysctl:read write ok" fails on s390 with "Read value !=
nux". This is because verifier rewrites a complete 32-bit
bpf_sysctl.file_pos update to a partial update of the first 32 bits of
64-bit *bpf_sysctl_kern.ppos, which is not correct on big-endian
systems.
Fix by using an offset on big-endian systems.
Ditto for bpf_sysctl.file_pos reads. Currently the test does not detect
a problem there, since it expects to see 0, which it gets with high
probability in error cases, so change it to seek to offset 3 and expect
3 in bpf_sysctl.file_pos.
Fixes: e1550bfe0d ("bpf: Add file_pos field to bpf_sysctl ctx")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20190816105300.49035-1-iii@linux.ibm.com/
Pull networking fixes from David Miller:
1) Don't corrupt xfrm_interface parms before validation, from Nicolas
Dichtel.
2) Revert use of usb-wakeup in btusb, from Mario Limonciello.
3) Block ipv6 packets in bridge netfilter if ipv6 is disabled, from
Leonardo Bras.
4) IPS_OFFLOAD not honored in ctnetlink, from Pablo Neira Ayuso.
5) Missing ULP check in sock_map, from John Fastabend.
6) Fix receive statistic handling in forcedeth, from Zhu Yanjun.
7) Fix length of SKB allocated in 6pack driver, from Christophe
JAILLET.
8) ip6_route_info_create() returns an error pointer, not NULL. From
Maciej Żenczykowski.
9) Only add RDS sock to the hashes after rs_transport is set, from
Ka-Cheong Poon.
10) Don't double clean TX descriptors in ixgbe, from Ilya Maximets.
11) Presence of transmit IPSEC offload in an SKB is not tested for
correctly in ixgbe and ixgbevf. From Steffen Klassert and Jeff
Kirsher.
12) Need rcu_barrier() when register_netdevice() takes one of the
notifier based failure paths, from Subash Abhinov Kasiviswanathan.
13) Fix leak in sctp_do_bind(), from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
cdc_ether: fix rndis support for Mediatek based smartphones
sctp: destroy bucket if failed to bind addr
sctp: remove redundant assignment when call sctp_get_port_local
sctp: change return type of sctp_get_port_local
ixgbevf: Fix secpath usage for IPsec Tx offload
sctp: Fix the link time qualifier of 'sctp_ctrlsock_exit()'
ixgbe: Fix secpath usage for IPsec TX offload.
net: qrtr: fix memort leak in qrtr_tun_write_iter
net: Fix null de-reference of device refcount
ipv6: Fix the link time qualifier of 'ping_v6_proc_exit_net()'
tun: fix use-after-free when register netdev failed
tcp: fix tcp_ecn_withdraw_cwr() to clear TCP_ECN_QUEUE_CWR
ixgbe: fix double clean of Tx descriptors with xdp
ixgbe: Prevent u8 wrapping of ITR value to something less than 10us
mlx4: fix spelling mistake "veify" -> "verify"
net: hns3: fix spelling mistake "undeflow" -> "underflow"
net: lmc: fix spelling mistake "runnin" -> "running"
NFC: st95hf: fix spelling mistake "receieve" -> "receive"
net/rds: An rds_sock is added too early to the hash table
mac80211: Do not send Layer 2 Update frame before authorization
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Fix error path of nf_tables_updobj(), from Dan Carpenter.
2) Move large structure away from stack in the nf_tables offload
infrastructure, from Arnd Bergmann.
3) Move indirect flow_block logic to nf_tables_offload.
4) Support for synproxy objects, from Fernando Fernandez Mancera.
5) Support for fwd and dup offload.
6) Add __nft_offload_get_chain() helper, this implicitly fixes missing
mutex and check for offload flags in the indirect block support,
patch from wenxu.
7) Remove rules on device unregistration, from wenxu. This includes
two preparation patches to reuse nft_flow_offload_chain() and
nft_flow_offload_rule().
Large batch from Jeremy Sowden to make a second pass to the
CONFIG_HEADER_TEST support and a bit of housekeeping:
8) Missing include guard in conntrack label header, from Jeremy Sowden.
9) A few coding style errors: trailing whitespace, incorrect indent in
Kconfig, and semicolons at the end of function definitions.
10) Remove unused ipt_init() and ip6t_init() declarations.
11) Inline xt_hashlimit, ebt_802_3 and xt_physdev headers. They are
only used once.
12) Update include directive in several netfilter files.
13) Remove unused include/net/netfilter/ipv6/nf_conntrack_icmpv6.h.
14) Move nf_ip6_ext_hdr() to include/linux/netfilter_ipv6.h
15) Move several synproxy structure definitions to nf_synproxy.h
16) Move nf_bridge_frag_data structure to include/linux/netfilter_bridge.h
17) Clean up static inline definitions in nf_conntrack_ecache.h.
18) Replace defined(CONFIG...) || defined(CONFIG...MODULE) with IS_ENABLED(CONFIG...).
19) Missing inline function conditional definitions based on Kconfig
preferences in synproxy and nf_conntrack_timeout.
20) Update br_nf_pre_routing_ipv6() definition.
21) Move conntrack code in linux/skbuff.h to nf_conntrack headers.
22) Several patches to remove superfluous CONFIG_NETFILTER and
CONFIG_NF_CONNTRACK checks in headers, coming from the initial batch
support for CONFIG_HEADER_TEST for netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
`struct nf_hook_ops`, `struct nf_hook_state` and the `nf_hookfn`
function typedef appear in function and struct declarations and
definitions in a number of netfilter headers. The structs and typedef
themselves are defined by linux/netfilter.h but only when
CONFIG_NETFILTER is enabled. Define them unconditionally and add
forward declarations in order to remove CONFIG_NETFILTER conditionals
from the other headers.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move some `struct nf_conntrack` code from linux/skbuff.h to
linux/nf_conntrack_common.h. Together with a couple of helpers for
getting and setting skb->_nfct, it allows us to remove
CONFIG_NF_CONNTRACK checks from net/netfilter/nf_conntrack.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A few headers contain instances of:
#if defined(CONFIG_XXX) or defined(CONFIG_XXX_MODULE)
Replace them with:
#if IS_ENABLED(CONFIG_XXX)
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is a struct definition function in nf_conntrack_bridge.h which is
not specific to conntrack and is used elswhere in netfilter. Move it
into netfilter_bridge.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is an inline function in ip6_tables.h which is not specific to
ip6tables and is used elswhere in netfilter. Move it into
netfilter_ipv6.h and update the callers.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three netfilter headers are only included once. Inline their contents
at those sites and remove them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Two headers include declarations of functions which are never defined.
Remove them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Several header-files, Kconfig files and Makefiles have trailing
white-space. Remove it.
In netfilter/Kconfig, indent the type of CONFIG_NETFILTER_NETLINK_ACCT
correctly.
There are semicolons at the end of two function definitions in
include/net/netfilter/nf_conntrack_acct.h and
include/net/netfilter/nf_conntrack_ecache.h. Remove them.
Fix indentation in nf_conntrack_l4proto.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In-between the MAC & PHY there can be a mode converter, which converts one
mode to another (e.g. GMII-to-RGMII).
The converter, can be passive (i.e. no driver or OS/SW information
required), so the MAC & PHY need to be configured differently.
For the `stmmac` driver, this is implemented via a `mac-mode` property in
the device-tree, which configures the MAC into a certain mode, and for the
PHY a `phy_interface` field will hold the mode of the PHY. The mode of the
PHY will be passed to the PHY and from there-on it work in a different
mode. If unspecified, the default `phy-mode` will be used for both.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently returns max-buf-size as size of the config attribute.
This patch incorporates changes to read this value from MFW (if available)
and provide it to the user. Also did a trivial clean up in this path.
Fixes: d44a3ced70 ("qede: Add support for reading the config id attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are two regression fixes for bugs that got introduced
during the system call rework that went into linux-5.1
but only bisected and fixed now:
- One patch affects semtimedop() on many of the less
common 32-bit architectures, this just needs a single-line
bugfix.
- The other affects only sparc64 and has a slightly more
invasive workaround to apply the same change to sparc64
that was done to the generic code used everywhere else.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XsII
-----END PGP SIGNATURE-----
Merge tag 'ipc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ipc regression fixes from Arnd Bergmann:
"Fix ipc regressions from y2038 patches
These are two regression fixes for bugs that got introduced during the
system call rework that went into linux-5.1 but only bisected and
fixed now:
- One patch affects semtimedop() on many of the less common 32-bit
architectures, this just needs a single-line bugfix.
- The other affects only sparc64 and has a slightly more invasive
workaround to apply the same change to sparc64 that was done to the
generic code used everywhere else"
* tag 'ipc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ipc: fix sparc64 ipc() wrapper
ipc: fix semtimedop for generic 32-bit architectures
GCC unescapes escaped string section names while Clang does not. Because
__section uses the `#` stringification operator for the section name, it
doesn't need to be escaped.
This fixes an Oops observed in distro's that use systemd and not
net.core.bpf_jit_enable=1, when their kernels are compiled with Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/619
Link: https://bugs.llvm.org/show_bug.cgi?id=42950
Link: https://marc.info/?l=linux-netdev&m=156412960619946&w=2
Link: https://lore.kernel.org/lkml/20190904181740.GA19688@gmail.com/
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[Cherry-picked from the __section cleanup series for 5.3]
[Adjusted commit message]
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Matt bisected a sparc64 specific issue with semctl, shmctl and msgctl
to a commit from my y2038 series in linux-5.1, as I missed the custom
sys_ipc() wrapper that sparc64 uses in place of the generic version that
I patched.
The problem is that the sys_{sem,shm,msg}ctl() functions in the kernel
now do not allow being called with the IPC_64 flag any more, resulting
in a -EINVAL error when they don't recognize the command.
Instead, the correct way to do this now is to call the internal
ksys_old_{sem,shm,msg}ctl() functions to select the API version.
As we generally move towards these functions anyway, change all of
sparc_ipc() to consistently use those in place of the sys_*() versions,
and move the required ksys_*() declarations into linux/syscalls.h
The IS_ENABLED(CONFIG_SYSVIPC) check is required to avoid link
errors when ipc is disabled.
Reported-by: Matt Turner <mattst88@gmail.com>
Fixes: 275f22148e ("ipc: rename old-style shmctl/semctl/msgctl syscalls")
Cc: stable@vger.kernel.org
Tested-by: Matt Turner <mattst88@gmail.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1) Allover mlx5 cleanups
2) Added port congestion counters to ethtool stats:
Add 3 counters per priority to ethtool using PPCNT:
2.1) rx_prio[p]_buf_discard - the number of packets discarded by device
due to lack of per host receive buffers
2.2) rx_prio[p]_cong_discard - the number of packets discarded by device
due to per host congestion
2.3) rx_prio[p]_marked - the number of packets ECN marked by device due
to per host congestion
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl1xgcsACgkQSD+KveBX
+j7XSwf6A6Ri61kZ4fLRfrKcMn7rq7uzUn855UjtNQUpDlmoKSu9lY+SGtMQMENq
7AMvUmgZJe2Sw47o3N9mxqPa86HS9uGDFhnF7HOKxa/4uzoqqvvdget4BhP0h1xS
tRDXScnuZfPIs1nuA0w1obgzYb0FwOJhtB1m3rQ6iywAohwmM8mYe9jPREfIGaoy
U9p+DZEJHIC2YKy4G7hymbNbaKMgMG9IYl9axNyqbGaA9xPTPO4+pBBFvEXffLh6
UAk7p3XHV0ZIiKq1STIqDJpz6ucP88ywg9Hnkkrz2U82xuk/E43tBvIM9pxgl/bh
UhJcoL2Wlr5aHNHgIlBgWZ07Q+J0aQ==
=iM0A
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-09-05
1) Allover mlx5 cleanups
2) Added port congestion counters to ethtool stats:
Add 3 counters per priority to ethtool using PPCNT:
2.1) rx_prio[p]_buf_discard - the number of packets discarded by device
due to lack of per host receive buffers
2.2) rx_prio[p]_cong_discard - the number of packets discarded by device
due to per host congestion
2.3) rx_prio[p]_marked - the number of packets ECN marked by device due
to per host congestion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fix from Dmitry Torokhov:
"A tiny update from Benjamin removing a mistakenly added Elan PNP ID so
that the device is again handled by hid-multitouch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - remove Lenovo Legion Y7000 PnpID
Looks like the Bios of the Lenovo Legion Y7000 is using ELAN061B
when the actual device is supposed to be used with hid-multitouch.
Remove it from the list of the supported device, hoping that
no one will complain about the loss in functionality.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203467
Fixes: 738c06d0e4 ("Input: elan_i2c - add hardware ID for multiple Lenovo laptops")
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Including:
* Revert for an Intel VT-d patch that caused problems for some
users.
* Removal of a feature in the Intel VT-d driver that was never
supported in hardware. This qualifies as a fix because the
code for this feature sets reserved bits in the invalidation
queue descriptor, causing failed invalidations on real
hardware.
* Two fixes for AMD IOMMU driver to fix a race condition and to
add a missing IOTLB flush when kernel is booted in kdump mode.
-----BEGIN PGP SIGNATURE-----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=SEs8
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Revert an Intel VT-d patch that caused problems for some users.
- Removal of a feature in the Intel VT-d driver that was never
supported in hardware. This qualifies as a fix because the code for
this feature sets reserved bits in the invalidation queue descriptor,
causing failed invalidations on real hardware.
- Two fixes for AMD IOMMU driver to fix a race condition and to add a
missing IOTLB flush when kernel is booted in kdump mode.
* tag 'iommu-fixes-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix race in increase_address_space()
iommu/amd: Flush old domains in kdump kernel
iommu/vt-d: Remove global page flush support
Revert "iommu/vt-d: Avoid duplicated pci dma alias consideration"
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloaded OvS datapath rules are translated one to one to tc rules,
for example the following simplified OvS rule:
recirc_id(0),in_port(dev1),eth_type(0x0800),ct_state(-trk) actions:ct(),recirc(2)
Will be translated to the following tc rule:
$ tc filter add dev dev1 ingress \
prio 1 chain 0 proto ip \
flower tcp ct_state -trk \
action ct pipe \
action goto chain 2
Received packets will first travel though tc, and if they aren't stolen
by it, like in the above rule, they will continue to OvS datapath.
Since we already did some actions (action ct in this case) which might
modify the packets, and updated action stats, we would like to continue
the proccessing with the correct recirc_id in OvS (here recirc_id(2))
where we left off.
To support this, introduce a new skb extension for tc, which
will be used for translating tc chain to ovs recirc_id to
handle these miss cases. Last tc chain index will be set
by tc goto chain action and read by OvS datapath.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map capability bit indicating that HCA supports port buffer's congestion
counters. Also map registers with the corresponding counters.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add set/get drv_data helpers for mdio device.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1vrJITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIC8BB/98XcWiaInD+SM6UjD2dVd1r0zhPKJS
WBK58G81+op3YP4DY8Iy+C24uZBlSlutVGoD/PIrZF39xXsnOtJuMVHC4LvtdADC
30uI/61JQNEjuX2AiTFudqDvYjZZKZ28HLqEnO2pWk3dMVL3+fkS3i7VQR7KJ/Gr
BYM6EzCdkbuWW/zsAVbKLJ8NswVmcdjP7eSK+exKppoWMtgCglZw1X6iP5YXDnbK
h3dGs687u8RfUra7j7vgnJzyQU4draMPsabaLDT5qw1PgYQ3k8MTVMBlULR0+HHO
qkBqumRwfOxay0z0XOgRuWrICKTH/b0SRLp3H53ZyfDo6+4TC9KGHRgX
=gwfZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.4-20190904' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-09-04 j1939
this is a pull request for net-next/master consisting of 21 patches.
the first 12 patches are by me and target the CAN core infrastructure.
They clean up the names of variables , structs and struct members,
convert can_rx_register() to use max() instead of open coding it and
remove unneeded code from the can_pernet_exit() callback.
The next three patches are also by me and they introduce and make use of
the CAN midlayer private structure. It is used to hold protocol specific
per device data structures.
The next patch is by Oleksij Rempel, switches the
&net->can.rcvlists_lock from a spin_lock() to a spin_lock_bh(), so that
it can be used from NAPI (soft IRQ) context.
The next 4 patches are by Kurt Van Dijck, he first updates his email
address via mailmap and then extends sockaddr_can to include j1939
members.
The final patch is the collective effort of many entities (The j1939
authors: Oliver Hartkopp, Bastian Stender, Elenita Hinds, kbuild test
robot, Kurt Van Dijck, Maxime Jayat, Robin van der Gracht, Oleksij
Rempel, Marc Kleine-Budde). It adds support of SAE J1939 protocol to the
CAN networking stack.
SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.
P.S.: This pull request doesn't invalidate my last pull request:
"pull-request: can-next 2019-09-03".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add forward declaration for struct gpio_desc in order to address
the following:
./include/linux/phy_fixed.h:48:17: error: 'struct gpio_desc' declared inside parameter list [-Werror]
./include/linux/phy_fixed.h:48:17: error: its scope is only this definition or declaration, which is probably not what you want [-Werror]
Fixes: 71bd106d25 ("net: fixed-phy: Add fixed_phy_register_with_gpiod() API")
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1uJGETHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIMnjCACzqf14rTtjFAS86C1KIjRaQu6XEZt5
2VFq3WqFB3OVgcvtJISIuDk9sN2oY0f3z8mSSCn56qgy1YOCmYnUNMArp7pbFSim
oPaM10gF/2FS4TM58nofqEBN4+sYVp5u1Sx/RAqSqNN9Ga6n0AtgsIG9Tt26FZuy
e3LPZFlXh9vhsZshGSFBrn+jL7y+tsVUxE1nw9FZ8W+lnp/JiyVYVL5LDzTZA24N
i7U5ENGMyCsakuRa/pm+l/OkwIXAuEyvr0R6H0SOAxuAVI+shqhu0le7QmDVtbz5
PiHNShILoZQzd9j8N3m3QOpgwHSIbmBHueRhgNRM6NahO+PWe4R3dvbT
=TBQL
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.4-20190903' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-09-03
this is a pull request for net-next/master consisting of 15 patches.
The first patch is by Christer Beskow, targets the kvaser_pciefd driver
and fixes the PWM generator's frequency.
The next three patches are by Dan Murphy, the tcan4x5x is updated to use
a proper interrupts/interrupt-parent DT binding to specify the devices
IRQ line. Further the unneeded wake ups of the device is removed from
the driver.
A patch by me for the mcp25xx driver removes the deprecated board file
setup example. Three patches by Andy Shevchenko simplify clock handling,
update the driver from OF to device property API and simplify the
mcp251x_can_suspend() function.
The remaining 7 patches are by me and clean up checkpatch warnings in
the generic CAN device infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.
J1939, ISO 11783 and NMEA 2000 all share the same high level protocol.
SAE J1939 can be considered the replacement for the older SAE J1708 and
SAE J1587 specifications.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Elenita Hinds <ecathinds@gmail.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The size of this structure will be increased with J1939 support. To stay
binary compatible, the CAN_REQUIRED_SIZE macro is introduced for
existing CAN protocols.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes the old method of allocating the per device protocol
specific memory via a netdevice_notifier. This had the drawback, that
the allocation can fail, leading to a lot of null pointer checks in the
code. This also makes the live cycle management of this memory quite
complicated.
This patch switches from the allocating the struct can_dev_rcv_lists in
a NETDEV_REGISTER call to using the dev->ml_priv, which is allocated by
the driver since the previous patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch introduces the CAN midlayer private structure ("struct
can_ml_priv") which should be used to hold protocol specific per device
data structures. For now it's only member is "struct can_dev_rcv_lists".
The CAN midlayer private is allocated via alloc_netdev()'s private and
assigned to "struct net_device::ml_priv" during device creation. This is
done transparently for CAN drivers using alloc_candev(). The slcan, vcan
and vxcan drivers which are not using alloc_candev() have been adopted
manually. The memory layout of the netdev_priv allocated via
alloc_candev() will looke like this:
+-------------------------+
| driver's priv |
+-------------------------+
| struct can_ml_priv |
+-------------------------+
| array of struct sk_buff |
+-------------------------+
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Abstract:
--------
Mellanox ConnetX devices supports packet matching, packet modification and
redirection. These functionalities are also referred to as flow-steering.
To configure a steering rule, the rule is written to the device owned
memory, this memory is accessed and cached by the device when processing
a packet.
Steering rules are constructed from multiple steering entries (STE).
Rules are configured using the Firmware command interface. The Firmware
processes the given driver command and translates them to STEs, then
writes them to the device memory in the current steering tables.
This process is slow due to the architecture of the command interface and
the processing complexity of each rule.
The highlight of this patchset is to cut the middle man (The firmware) and
do steering rules programming into device directly from the driver, with
no firmware intervention whatsoever.
Motivation:
-----------
Software (driver managed) steering allows for high rule insertion rates
compared to the FW steering described above, this is achieved by using
internal RDMA writes to the device owned memory instead of the slow
command interface to program steering rules.
Software (driver managed) steering, doesn't depend on new FW
for new steering functionality, new implementations can be done in the
driver skipping the FW layer.
Performance:
------------
The insertion rate on a single core using the new approach allows
programming ~300K rules per sec. (Done via direct raw test to the new mlx5
sw steering layer, without any kernel layer involved).
Test: TC L2 rules
33K/s with Software steering (this patchset).
5K/s with FW and current driver.
This will improve OVS based solution performance.
Architecture and implementation details:
----------------------------------------
Software steering will be dynamically selected via devlink device
parameter. Example:
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
mlx5 software steering module a.k.a (DR - Direct Rule) is implemented
and contained in mlx5/core/steering directory and controlled by
MLX5_SW_STEERING kconfig flag.
mlx5 core steering layer (fs_core) already provides a shim layer for
implementing different steering mechanisms, software steering will
leverage that as seen at the end of this series.
When Software Steering for a specific steering domain
(NIC/RDMA/Vport/ESwitch, etc ..) is supported, it will cause rules
targeting this domain to be created using SW steering instead of FW.
The implementation includes:
Domain - The steering domain is the object that all other object resides
in. It holds the memory allocator, send engine, locks and other shared
data needed by lower objects such as table, matcher, rule, action.
Each domain can contain multiple tables. Domain is equivalent to
namespaces e.g (NIC/RDMA/Vport/ESwitch, etc ..) as implemented
currently in mlx5_core fs_core (flow steering core).
Table - Table objects are used for holding multiple matchers, each table
has a level used to prevent processing loops. Packets are being
directed to this table once it is set as the root table, this is done
by fs_core using a FW command. A packet is being processed inside the
table matcher by matcher until a successful hit, otherwise the packet
will perform the default action.
Matcher - Matchers objects are used to specify the fields mask for
matching when processing a packet. A matcher belongs to a table, each
matcher can hold multiple rules, each rule with different matching
values corresponding to the matcher mask. Each matcher has a priority
used for rule processing order inside the table.
Action - Action objects are created to specify different steering actions
such as count, reformat (encapsulate, decapsulate, ...), modify
header, forward to table and many other actions. When creating a rule
a sequence of actions can be provided to be executed on a successful
match.
Rule - Rule objects are used to specify a specific match on packets as
well as the actions that should be executed. A rule belongs to a
matcher.
STE - This layer is used to hold the specific STE format for the device
and to convert the requested rule to STEs. Each rule is constructed of
an STE chain, Multiple rules construct a steering graph. Each node in
the graph is a hash table containing multiple STEs. The index of each
STE in the hash table is being calculated using a CRC32 hash function.
Memory pool - Used for managing and caching device owned memory for rule
insertion. The memory is being allocated using DM (device memory) API.
Communication with device - layer for standard RDMA operation using RC QP
to configure the device steering.
Command utility - This module holds all of the FW commands that are
required for SW steering to function.
Patch planning and files:
-------------------------
1) First patch, adds the support to Add flow steering actions to fs_cmd
shim layer.
2) Next 12 patch will add a file per each Software steering
functionality/module as described above. (See patches with title: DR, *)
3) Add CONFIG_MLX5_SW_STEERING for software steering support and enable
build with the new files
4) Next two patches will add the support for software steering in mlx5
steering shim layer
net/mlx5: Add API to set the namespace steering mode
net/mlx5: Add direct rule fs_cmd implementation
5) Last two patches will add the new devlink parameter to select mlx5
steering mode, will be valid only for switchdev mode for now.
Two modes are supported:
1. DMFS - Device managed flow steering
2. SMFS - Software/Driver managed flow steering.
In the DMFS mode, the HW steering entities are created through the
FW. In the SMFS mode this entities are created though the driver
directly.
The driver will use the devlink steering mode only if the steering
domain supports it, for now SMFS will manages only the switchdev
eswitch steering domain.
User command examples:
- Set SMFS flow steering mode::
$ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime
- Read device flow steering mode::
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl1uxPAACgkQSD+KveBX
+j5AkggAymoYqG2G+s8cLa4vQFySaD1Td3VzzWglp7PlpDBE3UcSoMAMg/gIDU1D
8F04PeCsJ6snt1ICk56vPNyAEHWfWeBUd56+QK5lEJBuwozyFvBh6HP81Bnr6T/n
n6uTx45ljAFQPTHJjEOLBPSzEXecLu07+mvpzSoW0F3ehfGbELhL1IkVobr/RELx
z4xZW9uM2vm5ylheWvjf4V1S/SvokgJazW9+4fh//rl8tfXgun5IfPoS0hqKie1/
h5sjcMSYkYR4gLVqrhKmBYHmHVl/h0TYROckW8iC/+XX7ailSo9uPG7lPa6cm+GE
7Bajlbz4oD/K5RWoByo+q+dmyjeVhQ==
=M9bS
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-09-01-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-09-01 (Software steering support)
Abstract:
--------
Mellanox ConnetX devices supports packet matching, packet modification and
redirection. These functionalities are also referred to as flow-steering.
To configure a steering rule, the rule is written to the device owned
memory, this memory is accessed and cached by the device when processing
a packet.
Steering rules are constructed from multiple steering entries (STE).
Rules are configured using the Firmware command interface. The Firmware
processes the given driver command and translates them to STEs, then
writes them to the device memory in the current steering tables.
This process is slow due to the architecture of the command interface and
the processing complexity of each rule.
The highlight of this patchset is to cut the middle man (The firmware) and
do steering rules programming into device directly from the driver, with
no firmware intervention whatsoever.
Motivation:
-----------
Software (driver managed) steering allows for high rule insertion rates
compared to the FW steering described above, this is achieved by using
internal RDMA writes to the device owned memory instead of the slow
command interface to program steering rules.
Software (driver managed) steering, doesn't depend on new FW
for new steering functionality, new implementations can be done in the
driver skipping the FW layer.
Performance:
------------
The insertion rate on a single core using the new approach allows
programming ~300K rules per sec. (Done via direct raw test to the new mlx5
sw steering layer, without any kernel layer involved).
Test: TC L2 rules
33K/s with Software steering (this patchset).
5K/s with FW and current driver.
This will improve OVS based solution performance.
Architecture and implementation details:
----------------------------------------
Software steering will be dynamically selected via devlink device
parameter. Example:
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
mlx5 software steering module a.k.a (DR - Direct Rule) is implemented
and contained in mlx5/core/steering directory and controlled by
MLX5_SW_STEERING kconfig flag.
mlx5 core steering layer (fs_core) already provides a shim layer for
implementing different steering mechanisms, software steering will
leverage that as seen at the end of this series.
When Software Steering for a specific steering domain
(NIC/RDMA/Vport/ESwitch, etc ..) is supported, it will cause rules
targeting this domain to be created using SW steering instead of FW.
The implementation includes:
Domain - The steering domain is the object that all other object resides
in. It holds the memory allocator, send engine, locks and other shared
data needed by lower objects such as table, matcher, rule, action.
Each domain can contain multiple tables. Domain is equivalent to
namespaces e.g (NIC/RDMA/Vport/ESwitch, etc ..) as implemented
currently in mlx5_core fs_core (flow steering core).
Table - Table objects are used for holding multiple matchers, each table
has a level used to prevent processing loops. Packets are being
directed to this table once it is set as the root table, this is done
by fs_core using a FW command. A packet is being processed inside the
table matcher by matcher until a successful hit, otherwise the packet
will perform the default action.
Matcher - Matchers objects are used to specify the fields mask for
matching when processing a packet. A matcher belongs to a table, each
matcher can hold multiple rules, each rule with different matching
values corresponding to the matcher mask. Each matcher has a priority
used for rule processing order inside the table.
Action - Action objects are created to specify different steering actions
such as count, reformat (encapsulate, decapsulate, ...), modify
header, forward to table and many other actions. When creating a rule
a sequence of actions can be provided to be executed on a successful
match.
Rule - Rule objects are used to specify a specific match on packets as
well as the actions that should be executed. A rule belongs to a
matcher.
STE - This layer is used to hold the specific STE format for the device
and to convert the requested rule to STEs. Each rule is constructed of
an STE chain, Multiple rules construct a steering graph. Each node in
the graph is a hash table containing multiple STEs. The index of each
STE in the hash table is being calculated using a CRC32 hash function.
Memory pool - Used for managing and caching device owned memory for rule
insertion. The memory is being allocated using DM (device memory) API.
Communication with device - layer for standard RDMA operation using RC QP
to configure the device steering.
Command utility - This module holds all of the FW commands that are
required for SW steering to function.
Patch planning and files:
-------------------------
1) First patch, adds the support to Add flow steering actions to fs_cmd
shim layer.
2) Next 12 patch will add a file per each Software steering
functionality/module as described above. (See patches with title: DR, *)
3) Add CONFIG_MLX5_SW_STEERING for software steering support and enable
build with the new files
4) Next two patches will add the support for software steering in mlx5
steering shim layer
net/mlx5: Add API to set the namespace steering mode
net/mlx5: Add direct rule fs_cmd implementation
5) Last two patches will add the new devlink parameter to select mlx5
steering mode, will be valid only for switchdev mode for now.
Two modes are supported:
1. DMFS - Device managed flow steering
2. SMFS - Software/Driver managed flow steering.
In the DMFS mode, the HW steering entities are created through the
FW. In the SMFS mode this entities are created though the driver
directly.
The driver will use the devlink steering mode only if the steering
domain supports it, for now SMFS will manages only the switchdev
eswitch steering domain.
User command examples:
- Set SMFS flow steering mode::
$ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime
- Read device flow steering mode::
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow steering actions: modify header and packet reformat
to the fs_cmd shim layer. This allows each namespace to define
possibly different functionality for alloc/dealloc action commands.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Global pages support is removed from VT-d spec 3.0. Since global pages G
flag only affects first-level paging structures and because DMA request
with PASID are only supported by VT-d spec. 3.0 and onward, we can
safely remove global pages support.
For kernel shared virtual address IOTLB invalidation, PASID
granularity and page selective within PASID will be used. There is
no global granularity supported. Without this fix, IOTLB invalidation
will cause invalid descriptor error in the queued invalidation (QI)
interface.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-by: Sanjay K Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Merge mlx5-next patches needed for upcoming mlx5 software steering.
1) Alex adds HW bits and definitions required for SW steering
2) Ariel moves device memory management to mlx5_core (From mlx5_ib)
3) Maor, Cleanups and fixups for eswitch mode and RoCE
4) Mark, Set only stag for match untagged packets
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Return MLX5_ESWITCH_NONE when CONFIG_MLX5_ESWITCH
is not selected.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move the device memory allocation and deallocation commands
SW ICM memory to mlx5_core to expose this API for all
mlx5_core users.
This comes as preparation for supporting SW steering in kernel
where it will be required to allocate and register device
memory for direct rule insertion.
In addition, an API to register this device memory for future
remote access operations is introduced using the create_mkey
commands.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
The patch adds driver support for configuring the grc dump config flags.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for reading the config id attributes from NVM
flash partition.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Make exported ftrace function not static
- Fix NULL pointer dereference in reading probes as they are created
- Fix NULL pointer dereference in k/uprobe clean up path
- Various documentation fixes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXWpTNRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qpXtAPsGoHDHkgPIyl9bnV0oZfwLrAl4qEyg
RpVp9ZMcG4UtMwEAp/SXRFzvL+EUiKyd1U3FZy2jhVec3+hX7SzIGqgONA4=
=ee8V
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Small fixes and minor cleanups for tracing:
- Make exported ftrace function not static
- Fix NULL pointer dereference in reading probes as they are created
- Fix NULL pointer dereference in k/uprobe clean up path
- Various documentation fixes"
* tag 'trace-v5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Correct kdoc formats
ftrace/x86: Remove mcount() declaration
tracing/probe: Fix null pointer dereference
tracing: Make exported ftrace_set_clr_event non-static
ftrace: Check for successful allocation of hash
ftrace: Check for empty hash and comment the race with registering probes
ftrace: Fix NULL pointer dereference in t_probe_next()
The function ftrace_set_clr_event is declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination. Because the
function was decided to be a part of API, this commit removes the static
attribute and adds the declaration to the header.
Link: http://lkml.kernel.org/r/20190704172110.27041-1-efremov@linux.com
Fixes: f45d1225ad ("tracing: Kernel access to Ftrace instances")
Reviewed-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
I've noticed that the "slab" value in memory.stat is sometimes 0, even
if some children memory cgroups have a non-zero "slab" value. The
following investigation showed that this is the result of the kmem_cache
reparenting in combination with the per-cpu batching of slab vmstats.
At the offlining some vmstat value may leave in the percpu cache, not
being propagated upwards by the cgroup hierarchy. It means that stats
on ancestor levels are lower than actual. Later when slab pages are
released, the precise number of pages is substracted on the parent
level, making the value negative. We don't show negative values, 0 is
printed instead.
To fix this issue, let's flush percpu slab memcg and lruvec stats on
memcg offlining. This guarantees that numbers on all ancestor levels
are accurate and match the actual number of outstanding slab pages.
Link: http://lkml.kernel.org/r/20190819202338.363363-3-guro@fb.com
Fixes: fb2f2b0adb ("mm: memcg/slab: reparent memcg kmem_caches on cgroup removal")
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of the fixes this time are for OMAP hardware,
here is a breakdown of the significant changes:
Various device tree bug fixes:
- TI am57xx boards need a voltage level fix to avoid damaging SD cards
- vf610-bk4 fails to detect its flash due to an incorrect description
- meson-g12a USB phy configuration fails
- meson-g12b reboot should not power off the SD card
- Some corrections for apparently harmless differences from the
documentation.
Regression fixes:
- ams-delta FIQ interrupts broke in 5.3
- TI am3/am4 mmc controllers broke in 5.2
The logic_pio driver (used on some Huawei ARM servers) needs a few
bug fixes for reliability.
A couple of compile-time warning fixes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdaUf1AAoJEJpsee/mABjZ+7YQALOXvCCfmYKkOSflNKEVXuiZ
tL7uj5PT2E136JoAoyEs8pqXLSpFnC/PxZ7GuN3+ZD0lqVz8PbIn5MhJ9KRrRzSF
lazjW++VQcFt1KR77l2umVi9/KiYD7UXU1HHmWN8+D/PX6EM+Gv1j65Ve8oTRn76
kfsq58y2YC6Rqv9dkiK91mteQ2bdA9b4O33V5M+Idq3aBwyNr5KKihDsNKPSvKl9
ibGmfGnukVcrVtU2reaUxNp2G1OsIKswq2bB0VwUlFMipPxML6rv94dJxDblb2Ns
nq3LeG+1TF9mbAxya2sWaF6fIBpxdEU5llFYRoIknSS+F9qM/nSVsi5WsyJJnCxk
mEvJLhhtt4gH2TZmPvZ6sPWFSVBHDnr8V3F4c0//aTRCN+tV7BCYbf8f3rv/CRNq
MLRsw8gHVPZyUUK9M4afeR3PqEx4/hbU9mpCtduAsiudnA1gtDBfQp8ODMop8aJ1
tCCdbFPoZIKKU/yhUm0OAbykPLVGb9zWGBNwYWuNs6IZFkyksGoFg1AspzKGvrcD
Knywz9dSmiDxRi3qDjVEd/9Rr/CtvUHmbaGq8RlTHmbB7WYoW84UPSD419V4j9vd
eIn4ScejKJCZUDACQsQXh7nnbg+QtnMq+3ODzvjsax2FAEKd8xtaZElSs8OA0U6b
xdqEuHPNY8VWBFXwAfdp
=mV+7
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The majority of the fixes this time are for OMAP hardware, here is a
breakdown of the significant changes:
Various device tree bug fixes:
- TI am57xx boards need a voltage level fix to avoid damaging SD
cards
- vf610-bk4 fails to detect its flash due to an incorrect description
- meson-g12a USB phy configuration fails
- meson-g12b reboot should not power off the SD card
- Some corrections for apparently harmless differences from the
documentation.
Regression fixes:
- ams-delta FIQ interrupts broke in 5.3
- TI am3/am4 mmc controllers broke in 5.2
The logic_pio driver (used on some Huawei ARM servers) got a few bug
fixes for reliability.
And a couple of compile-time warning fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
soc: ixp4xx: Protect IXP4xx SoC drivers by ARCH_IXP4XX || COMPILE_TEST
soc: ti: pm33xx: Make two symbols static
soc: ti: pm33xx: Fix static checker warnings
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: dts: Fix incomplete dts data for am3 and am4 mmc
bus: ti-sysc: Simplify cleanup upon failures in sysc_probe()
ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack
ARM: dts: dra74x: Fix iodelay configuration for mmc3
ARM: dts: am335x: Fix UARTs length
ARM: OMAP2+: Fix omap4 errata warning on other SoCs
bus: hisi_lpc: Add .remove method to avoid driver unbind crash
bus: hisi_lpc: Unregister logical PIO range to avoid potential use-after-free
lib: logic_pio: Add logic_pio_unregister_range()
lib: logic_pio: Avoid possible overlap for unregistering regions
lib: logic_pio: Fix RCU usage
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
ARM: dts: vf610-bk4: Fix qspi node description
ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7
...
